Optimus XEMED-P User manual

Brand: Optimus

Model: XEMED-P

Type: User manual

1 XELLIP washable master station - 604-0008D

TECHNICAL SHEET

XELLIP

System

XELLIP washable master station

with easy clean surface

Installation

Programming

Connection Use

INTRODUCTION

Product references: 540.4000 - 540.4100 (WI-FI)

The XELLIP washable master station with easy clean surface is part of a complete, powerful Full IP multimedia system.

With native SIP, it includes the following functions (according to the version):

 Establishing audio communication over IP

 Registration on SIP Server (can register with three servers)

 Managing a 12-button keypad

 Managing function keys (line tap, end call, directory, call on hold, etc.)

 Managing 1 to 4 programmable function buttons

 Managing an "on-off" input

 Managing automatisms developed on the interfaces (time and logic relations)

 Managing station profiles according to time slots

 A 128x64-pixel graphic display.

 A single-pole dry contact to control a keeper or other organ

 Supports the connection of an external amplifier (for example, an induction loop amplifier, ref. 540.3000)

 Thanks to its embedded web server, it can be configured, monitored and operated from any browser

 The PoE (Power over Ethernet) function

 The Wi-Fi function is available (optional)

 Secure the Ethernet network by using the 802.1X protocol (Radius)

 Integrate SNMP protocol (Simple Network Management Protocol)

 Update by TFTP.

 Backup on power failure.

 Integrate VLANs

VERSIONS

• The standard version of the washable master station has audio functions

• Wi-Fi functionality optional

2 XELLIP washable master station - 604-0008D

CONNECTION

15-30VDC Power supply

J45: ETHERNET & 10/100 POE

USB (NC)

Logic input

Relay output

Reset Button

Amplifier connection

or magnétic induction loop

R T E C

• Power supply connection

The station requires a power supply of 15 V to 30 V.

Comment: the station can be powered by the PoE network

• Connection to the IP network

The connection is carried out by a 10/100 Mbit RJ45 Ethernet link.

• Connection of the relay output

The connection is carried out via a 3-point terminal block providing a "make-and-break contact" interface (TRC).

If you use one of these relay outputs to control an AC or DC door release, wire a non-polarised 58 V diode in parallel on the

dry contact between C and T or between C and R according to the intended use (diode included).

• Input connection

An on-off input allows the connection of a dry contact (do not supply power). In order to be activated, the input must be

earthed.

The contact can be up to 1 km away.

3 XELLIP washable master station - 604-0008 D

USE

• IP address of the station

Every station must have its own IP address in the network. This address can be provided by the network server (DHCP

addressing) or configured manually. The address can be configured from a PC using the web server of the station (The

station is delivered by default with a DHCP address. If no DHCP server is present, then the station will take a fixed IP

address of domain IP4All: 169.254.xx.xx. The IP address of station will be found by the application CastelIPSearch).

• Accessing the web server of the station

You can use any web browser, such as Firefox or Internet Explorer, to connect to the web server of the station. To do so,

open your internet browser on any PC connected to the network and enter: "https://" followed by the IP address of the

station ([https://ip_address_of_the_station]). You will then be connected directly to the web page for the station. Now

you simply need to enter your username (default: admin) and password (default: admin) to access the functions of the

web server.

The web server provides information on the station and allows you to configure it.

In order to access all the functions, go to View / Full view.

On-line help, which can be accessed from any menu, provides information on the

various functions of the web server.

4 XELLIP washable master station - 604-0008 D

FUNCTIONS

The washable master station is designed to dialogue, via the IP network, with other XELLIP stations, softphones, SIP phones or any

other elements that are compatible with the SIP standard.

• General functions of the washable master station

 Configuring a network connection

 Setting up a SIP account

 Managing audio communication

o Setting the level of priority of the station

o Setting a call and communication time-out

o Automatic pick-up with and without delay

o Enabling secret mode for automatic pick-up

• Functions of the audio interface

 Setting the speaker volume and the microphone volume

 Setting the voice transmission mode (Full Duplex / Half Duplex)

 Setting a noise-reduction level

 Configuring the RTP port number

 Validating / invalidating audio codecs

 Setting ringtones and dial tones

 Setting DTMF commands for controlling, for example, the local relay.

• Functions of the on-off input interface

 Configuring the STATUS or COUNTER input

 Configuring the active status of the input (contact open or closed)

 Setting a timer for acknowledging a status change (anti-bounce function)

 Configuring the counter threshold

 Inhibiting the input

• Programmable button functions

All the buttons are programmable and can be used for:

 Making a call to 1 to 10 stations, simultaneously or with a time-delay

 Controlling the local relay, the relay of the station making or receiving the communication

 Sending a DTMF code

 Activating forwarding to a station

 Activating a call transfer

 Activating "do not disturb" mode

• Functions of the output interface

The relay output interface can be programmed for:

 Configuring the type of relay output: monostable, bistable or flashing

 Configuring the type of NO/NC contact

 Controlling the Start/Stop output

 Controlling the Forcing Open/Closed output



Configuring the time parameters of the output

• Web server profile function

You can create, edit or delete operating profiles for the station. Each profile indicates a priority for the station, a configuration of the

function buttons, a directory configuration (blacklist/whitelist) and access rights to the station.

The station can operate with a single profile or with various profiles according to time slots or according to the voice-transmission

user logged into the station.

• Web server user function

The web server of the station allows you to grant, edit or remove user rights, specifying the username, password and operating

language of the user.

In the user tab, you can create, import, export and view a directory. This directory contains all the users that can be

contacted from the station.

• Function for voice-transmission users of the station

In the user tab, you can create, edit or delete the voice-transmission users to whom you assign a profile. Then, a user can

log into the station using his/her username and password and activate his/her profile on the station.

• Relation functions of the web server

The web server can be used to configure automatisms also known as relations. There are two types of relations:

 Time: launches actions in identified time slots. Time relations have three levels of priority (high, medium and low).

 Logic:

o logic condition: launches actions when certain conditions are fulfilled (active, standby, etc.). A logic relation can

include several conditions using operators such as AND, OR, NOT and XOR. Moreover, a logic relation can launch

several actions.

5 XELLIP washable master station - 604-0008 D

o Digital condition (counter): performs actions by comparing the value of a counter with various thresholds. It is also

possible to add or subtract counter values and to compare the result obtained.

• Logic input functions (or flags) of the web server

Logic inputs enable two functions, specifically:

 to create a logic state capable of conditioning actions in the relations.

 to create a counter which will be updated according to events and according to the value of this counter for possibly

launching one or more actions.

• Backing up and recovering system parameters

The parameters of the station can be fully backed up and recovered (configuration, profiles, relations, directory, etc.).

The station can be reset to its factory default settings by pressing the reset button for 10 seconds when starting up the

station.

• Administration management SNMP

The station includes an agent SNMP (Simple Network Management Protocol) to respond to SNMP requests and to send

notifications (traps) to a SNMP manager.

From web pages, you can:

 Configure different community (read / write)

 Configure system data (“sysContact” and “sysLocation”)

 Configure notifications (recipient, community ...)

 Download “MIB Castel”

It supports SNMPv1 and SNMPv2c versions.

• Autotest function

The station has several tests to validate its functioning:

 Autotest “Micro and speaker”: to test the remote operation of speakers and microphone. From the page "Advanced

Settings", it is possible to adjust levels of the test following the installation environment. This test can be triggered

from the web server or an SNMP command. The test result is visible through the history of the web server and an

SNMP notification.

 Autotest “keys”: the detection of a blocked mechanical button (contact for over 20s) is indicated by an SNMP

notification and an event is reported in the history of the web server.

• Update by TFTP

Updating software with TFTP can be very useful when several stations must be updated.

The station is looking forward a TFTP server which provides the available software release. If the station is concerned

by this update, it downloads it and flashes it independently.

The updating software takes place most of the time when the software release on the server is newer than the one

installed on the station.

It is possible to force an updating process to a specific release of the TFTP server.

The TFTP server can request the stations to reset the current configuration, so the data partition is cleared.

It is possible to configure the station to detect a new release when the station is starting or cyclically.

• Backup on power failure

When a power failure occurs, the station must be able to backup the following:

 counter values

 History

 secured events (these events are defined in VDIPServeur)



The states of interfaces

6 XELLIP washable master station - 604-0008 D

INSTALLATION

• Flush mounting:

- Make a recess in the support with the following minimum dimensions: height 268 mm, width 112 mm and depth

48 mm.

- Position and attach the embeddable base in the recess, pressing the embedding abutments against the support in

which the recess is made.

- Position and clip the plate onto the base.

40= =

60= =

130

= =

26= =

47 4

110= =

Butée d’encastrement

IMPORTANT WARNING: Use a flat screwdriver to remove the plate, inserting the tip in the slot provided for this

purpose at the bottom of the plate. Next, rotate the screwdriver and pull manually in order to release the plate from its

support.

7 XELLIP washable master station - 604-0008 D

TECHNICAL SPECIFICATIONS

• Conformity with European standards

- Safety according to EN 60950

- EMC emissions according to EN 55022 class B

- EMC immunity according to EN 55024

• Mechanical properties

- Protection rating IP54 according to EN 60529.

- Polyester front panel.

- Weight: 1.5 kg

- Raised or flush mounting (optional).

- Dimensions: Front panel: H 280 mm x W 130 mm

Embeddable base: H 265 mm x W 110 mm x D 47 mm

Strap (optional): H 282.5 mm x W 132.5 mm x D 65 mm

• General electrical properties

- Protection against electric shocks, class 3 according to EN 60950

- Storage temperature: -20 ºC to +70°C.

- Operating temperature: 0 to +50°C

- Input voltage: 15 V DC (15 V to 30 V)

- Consumption: 15 V / 150 mA in standby and 15 V / 200 mA during communication

• Button:

- Acquisition speed: 5 Hz (200 ms)

• Input:

- One protected and filtered on-off input

- Acquisition speed: 5 Hz (200 ms)

• Output:

- Potential-free relay output

- Interrupting capacity of the relay 42.4 V AC / 60 V DC / 5 A / 150 VA

-The maximum frequency is 5 Hz (minimum switching time: 200 ms)

• Display:

- Backlit 128x64 pixel graphic display.

- White text on blue background

• Audio codec:

- G711 Ulaw/Alaw

- GSM

- G722

• DTMF:

- RFC-2833

- SIP INFO

• Ethernet 10/100 Mbit network:

- Static IP or DHCP

- Wi-Fi wireless network according to IEEE 802.11b/g standard

- PoE class 2 according to IEEE 802.3af standard

-802.1X protocol (Radius)

-SNMP v1 & v2c

Protect the environment

Dispose of the product in

accordance with environmental

conservation rules

CASTEL

Z.I. de Saint Lambert des levées - 49412 SAUMUR Cedex - FRANCE

www.castel.fr - Tel.: +33 2 41 40 41 40 - Fax: +33 2 41 40 41 49

Non-contractual document. The manufacturer reserves the right to make any changes it considers necessary without prior warning.

Optimus XEMED-P User manual

Optimus XEMED-P User manual

Optimus XEMED-P User manual

Related papers

Other documents