2. Contacta
  3. STS-K072
STS-K072

Contacta STS-K072 User guide

  • Hello! I am an AI chatbot trained to assist you with the Contacta STS-K072 User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Installation &
User Guide
Window Intercom System
Speaker Pod and Screen Mounted
Microphone - STS-K072
February 2022
2
Contents
Product Overview
Components
Connections
Installation Instructions
Speaker & Microphone Kit Installation
  StaSideInstallation
Customer/Visitor Installation
Hearing Loop Installation
 AmplierSetup
Troubleshooting
Engineer’s Mode
3
3
4
5
6
6
7
10
11
13
14
Contactahasapolicyofcontinuousproductdevelopment,andthereforesmallspecication
changesmaynotbereectedinthismanual.Images,labels,packaging,accessoriesandproduct
coloursaresubjecttochangewithoutnotice.
3
Speaker & Microphone Components
Product Overview
Window intercom systems provide assistance for clear communication where
normal speech is impaired by use of glass, a security screen or other similar
barriers.
There is an optional hearing loop facility, providing additional assistance for
hearingdevicewearers.
1. Installation and User Manual
2. Amplier
3. IEC Lead
4. Power Supply
5. HearingLoopAerial
(optional)
Fixing Kit:
• Adhesive Clip x 10
• No.6x1/2”CountersunkScrewsx15
• P-Clips x 6
5
General Components
1. Speaker Pod
2. StaPod
3. Screen Mounted Microphone
with Bent Stem
4
3
2
1
1
3
24
4
Connections
When removing green connectors for feeding cables through holes,
ensure all are refitted at the correct polarity before connection to the
amplifier.
It is recommended to take photos as a record before taking any cables
apart. This is to ensure proper reconnection; incorrect wiring may impact
performance.
5
Werecommendthatinstallationiscarriedoutbyaqualiedengineer,
adheringtorelevantstandards.
Checkthecontentsoftheboxtofamiliariseyourselfwiththecomponents.
Installation Instructions
A basic toolkit recommended to install the system will include:
Trim cables if necessary (excluding the power supply)
to the required length to connect to the back of the
amplier.Bareapproximately6mmofthecableendsto
connecttothe2pinplugs.
• Wire Cutters/Strippers
• Tape Measure
• Pencil or Marker Pen
• Cable Ties
• Trunking
• Screwdrivers(FlatorBlade2.5mm
and Phillips Head PH2)
• Battery or Mains Drill
• Drillbits: 2mm, 3mm, 5mm and 7mm
• Cable Tacking Gun (10mm)
Recommended Tools
Staff Counter Side
Customer / Visitor
Counter Side
StaPod
Screen Mounted
Microphone
Speaker Pod
Negative -
or screened cable
Positive +
6
1. Placetheamplierunderthestacounter,ensuringthatitwillnot
obstructstawhentheyaresitting.
2. Markthefourxingpointsfortheamplierunderthecounter.
4. Drillandxtheamplierinplaceusingthesuppliedscrews.
6. Installtheamplier’spowersupplyclosetoapowersocketoutletusing
thesuppliedmountingbracketandxingscrews.
Fixing points
AmplierInstallation
7
Microphone & Speaker Installation
1. Position the screen mounted microphone stem’s on the customer side of
thecountertop.
2. Markthe2xingpointsand1cableroutereadyfordrilling(seethe
diagrambelow).
3. Drillpilotholesforthexingsandacableholeifneccesary.
4. Feedwiringthroughthecableholebacktotheamplierandxthe
microphoneinplaceusingthesuppliedscrews.
5. Fix the microphone head to the screen using the double-sided pad
supplied.
6. Placethestapodonthestasideofthecountertop,ensuringit
doesnotcauseanobstructionandisasclosetostaaspossible.The
recommended minimum distance between this pod and the screen
mountedmicrophoneis300mm.
Staff Counter Side
Customer / Visitor
Counter Side
StaPod
Screen Mounted
Microphone
Speaker Pod
8
7. Place the speaker pod on the customer side of the counter top, ensuring it
doesnotcauseanobstruction.
8. Speakerpodsandstapodscanbeeitherfreestandingorxed.Moveto
step14ifyoudonotwishtoxthepodstothecounter.
9. Usecablemanagementholesinthecountertorunthestapodand
speakerpodcablestotheamplier.Iftherearenotalreadycable
managementholes,drillsuitablelocationsneartherearofboththesta
andcustomersidesofthecounter.
10. Thereare2xingmethodsforthespeakerpod/stapod.Eitherxthe
pods to a surface using (a) the provided double-sided sticky pad or (b) the
providedscrews.
a. Toxthepodinplaceusingthedouble-sidedadhesivepad:
i. Removeonesideofthelinerandadherethistothebaseofthe
podcentrally.
ii. Removethesecondlinerandadherethepodinitsdesired
location.
b. Toxthepodsusingthescrews:
i. Screwx2countersunkscrewsintothexingsurfaceata28mm
distanceapart.
ii. Ensurethatapproximately4mmofthescrewheadisabovethe
xingsurface.
28mm
User direction
90 degrees
Note: Place the screws at a 90 degree angle facing the intended
28mm
9
users’standingposition.
iii. Placeyourpodontothescrewheads,ensuringthesetintothe
twistxingpointslocatedonthebottomoftheunit:
iv. Twisttheunitclockwisetotightenitinplace.Ifthepodistootight
orloose,adjustthescrewsaccordingly,thenre-attach.
11. Toxthemousemicrophonetoasurface,usetheprovideddouble-sided
xingpadorscrewthroughthescrew-holeinitscap.
12. Feedthewiresthroughthecablemanagementholes.
13. Avoidlooseortrailingcables.Usetrunkingortopreventtriphazardsor
unitsbeingtuggedfromtheirposition.
14. Routeallcablingneatlytotheamplierlocationonthestaside.
10
Theaerialshouldbexedunderthedesk-toporcountercentrallyonthe
customerorvisitorside,onehalfmountedhorizontallyunderthecounterand
theotherhalfmountedvertically,facingthecustomer/visitor(asintherst
scenariobelow).
Position the aerial under the counter using either the provided P-clips
oranotherxingmethodofyourchoice.Seethediagrambelowfor
recommendedpositioning.
Aistheoptimumlayoutforacounterhearingloop.
B and C are acceptable only if A is not possible and the layout is aligned so
thatthemagneticeldwillbedirectedtowardsuser’sheadheights.
Ensureallhearingloopsignageisdisplayedclearly.
X
X
Hearing Loop Installation
(Optional)
A B C
11
AmplierSetup
1. Connectallgreenplugstothebackoftheamplier,followingthe
locationsprintedabovethesockets(seepage4).
2. PowerontheamplierbypressingtheOn/Obutton.
3. Whenpoweredandinnormaloperationalmodetheamplierwilldisplay
VolumeInLED1andVolumeOutLED1assteadygreen.
4. Whentheamplierisswitchedo,allaudioismutedandnoneofthe
LEDsareilluminated.Pressinganybuttonwillturntheamplieronagain.
5. AdjustVolumeInandVolumeOuttoacomfortablelevel.
6. Press and hold the Volume In (+) or (-) buttons to increase or decrease the
level.ThecorrespondingLEDbarwillshowthevolumesetting.
6. Ensure the mouse microphones are placed as close to their intended
usersaspossible.
7. Checktheamplierisfullyfunctionalbyensuringthered‘fault’lightis
NOTshowingonthefront.
8. The Amplifier is now set up.
OurWindowIntercomSystemampliersarepre-settovolumelevels
suitablefornearlyallusers.ShouldyouneedtoadjusttheMaximum
Volume,DuckingorHearingLooplevelsoutsideofthepre-setamplier
parameters,useEngineer’sMode(seepage13).
Overview of Front Panel Buttons
Volume In (Customer/Visitor to Staff)
Increase and decrease
Volume Out (Staff to Customer/Visitor)
Increase and decrease
Settings
On/O
Setup
12
Factory Default Settings
Toreturntheamplierthefactorydefaultsettings:
1. Unplugthepowersupplyandthenreconnectit.
2. PresstheOn/ObuttonandVolumeIn(-)buttontogether,thenrelease.
3. The Volume In LED bar will have all LEDs illuminated, while the Volume
OutLEDbarwilldisplaythermwarerevisionnumberinaxedpattern
ofLEDs.Thisindicatesthatdefaultsettingshavebeenrestored.
Fault Diagnosis LEDs
• Volume In LED 8 will stay red if there is a
faultwiththestamicrophone.
• Volume Out LED 8 will stay red if there is a
faultwiththecustomer/visitormicrophone.
• VolumeInLED8willashredifthereisa
faultwiththeloop(e.g.abrokenaerial).
13
Symptom Possible Fault Action
There is no
power
detected
through the
amplifier (and
there is power
at the socket).
1) Power jack not plugged in or
faulty.
2)Plugfusehasblown.
3) Faultypowersupplyunit.
4)Faultyamplier.
1)Checkpowerjackisrmlyplugged
in.
2)Replacefuse.Ifitblowsagain,
replacethepowersupplyunit.
3)Replacethepowersupplyunit.
4)Replaceamplier.
The red LED is
illuminated on
front panel.
1) Constant red LED:
Staorcustomer/visitor
microphonefault.
2) Red LED comes on after speech:
Inductionloopfault.
1) Ensure microphone is wired
correctlyandrmlypluggedin. Try
alternative microphone to ensure
portisworking.
2) Ensure induction loop connector is
wiredcorrectlyandrmlypluggedin.
I can’t hear
audio through
the induction
loop.
1) Induction loop or microphone is
disconnected.
2)Looptesterhasafault.
1 ) Check instructions for correct
connections and, if possible, check
the hearing device with a known
workinghearingloop.
2) Ensure loop tester has a new set
ofbatteries.
I can hear
interference
through
speakers
(buzzing /
whistling /
hissing).
1) Unscreened or poorly earthed
third party equipment is being used
incloseproximity.
2)Internalvolumegainsettohigh.
3) Incorrect power supply being
used.
1)Switchoanythirdparty
equipment to identify the source of
interference.
2)AccesstheamplierEngineer’s
Modetoadjusttheinternalsettings.
3) Ensure that our grounded power
supplyunitisconnected.
Amplifier goes
into feedback.
1)Internalvolumegainsettoohigh.
2) Microphone positioned too close
tospeaker.
1)AccesstheamplierEngineer’s
Modetoadjusttheinternalsettings.
2) Move the microphone to a
locationfurtherfromthespeaker.
Unit does not
go into power
saving mode.
1)Ambientnoiseinareaistoohigh. 1)Switchoanyairconsystems,
desktop fans and/or computers to
reduceambientnoise.
Troubleshooting
If no action is successful please seek assistance from
yourdistributororaContactainstaller.
14
Engineer’s Mode
BeforeenteringEngineer’sMode,cyclethepower.Todothiseither:
• Switchthepoweroatthemainssocketandbackonagain
• Removethepowerconnectorandre-insertit
To enter Engineer’s Mode, simultaneously press and release the following
buttons within 20 seconds of cycling the power:
• Settings button
• Volume In increase button
• Volume Out increase button
Number1LEDontheVolumeInwillashgreentoindicatethatyouarein
Engineer’sMode.
Theon/oandsettingsbuttonsinEngineer’sModeoperateasfollows:
TheamplierwillautomaticallyexitEngineer’sModeifnobuttonsare
pressedfor2minutes.
Thereare3editablesetupareasinEngineer’sMode.Youwillalwaysenter
setuparea1rst.ThegreenVolumeInLEDbarwillashtoindicatewhich
setupareayouarein.
Setup Area 1:
Maximum Volume Adjustment (LED 1 flashes)
Setup Area 1 allows you to adjust the Volume In and Volume Out levels to
furtheroptimisethesystemfortheenvironmentinwhichitisinstalled.
Engineer’s Mode allows you to adjust the Volume In and Out levels, Ducking
levels and Hearing Loop levels to better suit your environment and achieve
thebestpossibleperformance.
Increase maximum
stavolumelevel
Decrease maximum
stavolumelevel
Increase maximum
customer volume level
Decrease maximum
customer volume level
Save and exit Engineer’s Mode
Move to the next setup area
15
1. Ensurethecustomerandstavolumesareturnedcompletelydown.
2. Adjuststa(VolumeIn)volumetoacomfortablelevel.Pressandhold
theVolumeIn(+)or(-)buttonstoincreaseordecreasethelevel.The
correspondingLEDbarwillshowthevolumesetting.
3. Increasecustomer(VolumeOut)volumeuntilfeedbackisheard.Press
and hold the Volume Out (+) or (-) buttons to increase or decrease the
level.ThecorrespondingLEDbarwillshowthevolumesetting.
4. Decreasecustomer(VolumeOut)volumeuntilfeedbackiseliminated.
Setup Area 2:
Ducking Adjustment (LED 2 flashes)
SetupArea2allowsyoutoadjusttheDuckinglevelortoturniton/o.
The ducking function is provided to reduce feedback on a window intercom
system.Feedbackoccurswhentheoverallsettingofbothvolumecontrols
istoohigh.Theduckingsystemworksbydetectingwhichmicrophoneinthe
conversationisbeingused,andtemporarilyreducingthevolumesetting.
Increase
ducking level
Decrease
ducking level
Ducking on
Duckingo
Increase drive
Decrease drive
The drive levels should be adjusted so the red LED 8 is illuminated only when
therearepeaksinthespeechvolume.
Iftheamplierdoesnothavealoopattached,turntheHearingLoopDriveo
asindicatedinthediagramabove.
Setup Area 3:
Hearing Loop Drive Adjustment (LED 3 flashes)
SetupArea3allowsyoutoadjusttheHearingLoopDriveortoturniton/o.
Hearing loops improve communication by enabling hearing device users to
hearsoundsourcesdirectly,cuttingoutbackgroundnoise.
Hearing Loop Drive on
HearingLoopDriveo
www.contacta.co.uk
[email protected].uk
+44 (0) 1732 223900
Technical Support - Ext 5
Further information is available on our website and our YouTube channel.
WindowIntercomSTS-A31HAmplier
Setup Video
Window Intercom Unboxing &
Positioning Guide Video
/