Pulsar AWZ710 Operating instructions

Brand: Pulsar

Model: AWZ710

Type: Operating instructions

Pulsar AWZ710 is a foot-operated emergency button that silently indicates alarm situations. It has numerous programmable functions for flexible adjustment to installation requirements. The optical technology-based pushbutton detector sends output signals in the form of contact connection/disconnection.

AWZ 710

v1.0

PN-K foot-operated emergency button

Edition

: 1 from the 11

February 2008

Supercedes edition

: -----------

07052009

1. Technical description, usage.

PN-K foot-operated emergency button is used for silent indication of alarm situation

occurrence, the unit is equipped with numerous programming functions which enable the

flexible adjustment to requirements of a particular installation. The pushbutton detector is made

according to the optical technology. The output signal is presented in a form of contacts

connection/disconnection (silently).

Fig. 1. The plate overview.

Terminals description:

12V

- button supply

GND

- ground

RST

- reset input

- output relay closing contact

- relay anchor

TAMP

- sabotage switch contacts

2. Optical indication.

Indication in normal operation:

• LED continuous lighting indicates button output activation.

• Fast flashing indicates time countdown unless alarm call off or power supply restart.

3. Parameters programming

Entering the programming: press PROG/RESET button for more than 2 s and release. The diode

will start flashing fast, in this mode short button pressing selects parameters we want to edit, the

number of active parameter is signalized by flashes of LED diode

Notice! If the button is not pressed in 20s, device will exit the programming mode.

Programs:

1. Emergency button press time.

2. Alarm call off time.

3. Output maintenance in monostable status

4. Output operation mode selection.

5. Exit programming.

Time set:

The program selection is confirmed by holding button pressed, it is confirmed by short flashes.

Another button press lights the LED diode. The time of pressed button is the time of a programmed

parameter. After button releasing the length of time set is sent to the device memory and the device

quits to the “main menu”.

Alarm call off time: it is time for calling off incidental button press, factory preset is 0s. To call off the

alarm during the call off time countdown, the button should be pressed again.

Button press time: required time of continuously pressed button to cause reaction. Factory preset is

1 s.

Output operation mode selection:

Short button press changes operation mode as below:

1) Monostable – output is active for a particular period of time (backup time change – program 3)

2) Catch – the output is active since “mass” connection to RTS input or short flash of PROG button.

3) Bistable – first disturbance activates the output, another disturbance deactivate the output etc.

The number of currently chosen mode is signalized by short diode flashes (1,2,3).

Acceptance: long press of PROG/RESET button or elapsing 20s.

Output reset in the CATCH mode: short press of PROG/RESET button or ground connection to

RTS input.

Fig. 2. Parameters programming.

Technical parameters:

Parameter

Value

Notes

Supply voltage

11-14VDC

Current consumption 17mA

30mA

Relay deactivated

Relay activated

Maximal switching current of output relay

0.5A

Maximal voltage of

contacts 50V DC or 30V

Working temperature 0°C ÷ 40°C

Dimensions width x height x depth 67 x 40 x 107 [mm]

WEEE MARK

The waste electric and electronic products, do not mix with general household

waste. There are separate collection system for used electric and electronic

products in accordance with legislation under the WEEE Directive

and is effective only with EU.

WARRANTY :

24 months since the sale date, 36 months since the production date.

THE WARRANTY IS VALID ONLY after presenting the invoice of the sale to which the claim refers.

Pulsar K.Bogusz Sp.j.

Siedlec 150, 32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail:

[email protected]

http://

www.pulsarspj.com.pl

Pulsar AWZ710 Operating instructions

Pulsar AWZ710 Operating instructions

Pulsar AWZ710 Operating instructions

Related papers

Other documents