RGBlink FLEX RS1 Quick start guide

FLEX RS1 Quick Start

• 4K@60Hz input via DP 1.2, HDMI 2.0 with

internal 4:4:4 processing and HDR

compliance.

• 4K@30Hz input via Dual Link DVI, HDMI

1.4

• 3 Different Operation Mode: Rotation,

Edge Blending and Splicing

• Independent output scaling to any

aspect or resolution

• Rotation: Any degree rotation for each

of the output

• Edge Blending: Independent edge

blending for each output

• Splicing: Image splicing for each 2K

output

• Cascade multiple units for additional

screens

• Control Support: Art-Net DMX512-A, RS

232, IP (TCP/UDP)

• Manage with XPOSE on Windows,

M

a

c

O

S

,

i

O

S

,

2/27

CONTENTS

Product Introduction ......................................................................................................... 3

Packing Configuration ...................................................................................................... 4

Hardware Orientation ....................................................................................................... 5

Front Panel ................................................................................................................... 5

Rear Panel .................................................................................................................... 6

Software Operation ........................................................................................................... 7

Software Installation .................................................................................................... 7

Environment Requirements .................................................................................. 7

Software Operation .................................................................................................. 10

Login to the Software ......................................................................................... 10

Web Links ............................................................................................................. 11

Connect Setting .................................................................................................. 11

System Setting ..................................................................................................... 11

Input Settings ....................................................................................................... 15

Output Settings .................................................................................................... 15

Operation Mode ................................................................................................. 18

Logout .................................................................................................................. 25

Contact Information ....................................................................................................... 27

!

Zhu Maggy 11/22/2018 5:22 PM

Deleted: 12

Zhu Maggy 11/22/2018 5:22 PM

Deleted: 12

Zhu Maggy 11/22/2018 5:22 PM

Deleted: 12

3/27

Product Introduction

FLEX RS1 enables creative video split including any degree rotation, edge

blending for the projector and video wall hard splicing. It supports two HDMI inputs,

a dual-link DVI input, a Display Port input and four DVI outputs. FLEX RS1 supports

up to 4K2K, the UHD input resolution. Different resolutions can be set in each

output.

FLEX RS1 features in multiple cascade, and simple managed by XPOSE software.

System Connection

RGBlink video processing solutions

provide a range of flexible configuration

options for professional applications.

4/27

AC Power Cable

!

RJ45 to DB9

Cable

RJ45 to RS232

RS232 to USB

Cable

Packing Configuration

Note:

AC Power Cable supplied as standard according to destination market.

USB Cable

!

HDMI Cable

Antistatic Bag

!

DVI to HDMI

Cable

!

5/27

Hardware Orientation

Front Panel

!

Panel Instruction

SIGNAL

Signal indicator lights when

device has connected with

input signal.

USB

Interface

To upgrade the device

POWER

Power indicator lights when

device has power supply.

6/27

Rear Panel

Input Interface

1

Input Card Slots

Supports input signals including dual-link DVI, HDMI1.4, HDMI2.0, DP1.2.

Each HDMI module supports 1 HDMI-A input.

Output Interface

4

4 DVI outputs

Control Interface

2

SLAVE IN

Connect to XPOSE software by RS 232. RGBlink supports a USB to RS

232 converter and the RS 232 to RJ45 cable for this connection, as

standard accessories.

5

ART-NET IN

Connect to ARTNET controller.

6

ART-NET loop

Connect to another equipment to make mutiple cascade.

Power Connection

3

Power Switch

7

AC 85-264V 50/60HZ

7/27

Software Operation

Software Installation

Minimum Requirements

Windows

Operation System

Windows 7/8/10

Processor

1GHz/32 bit or 64 bit processor

Memory

2Gb

Hard Disk

16Gb

Graphics

128Mb/DirectX9

Display

1280X720

Mac

!

Operation System

Mac OS

Processor

1.0GHz+

Memory

512M+

Hard Disk

512M+

Graphics

512M+

Display

1366x768

8/27

!

1. Double click icon, it will pop-up the Installer Language

box, select the language, for example, select “English”, and click “OK” to

confirm.

!

It will pop-up the installer box, and click “Next” to install, as follows:

!

2. Select “Browse...” to select the XPOSE software install location and click install:

!

9/27

3. User should get the rights in “Roles Management” when install the software to

disk C if the system is Windows 7 or above.

!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!

!

!!!!!

!

4. Click “Finish” and is ready to run the XPOSE management software:

!

10/27

Software Operation

Login to the Software

1. Double click the icon on the desktop, then login into the interface. The

user name is Admin, and defaultly there is no password. Select “FLEX RS1”, select

language “English” and enter the software by clicking “Login”.

!

2. If user wants to change the language to Chinese, click the drop down arrow

after “Language” and select “Chinese”, then click “Login” to enter the software.

11/27

3. After entering the software, the main interface shows as follows:

XPOSE management software consists of Operation Mode, Input Settings, Output

Settings, System Settings and Log out. In the following parts come with the detail.

Web Links

XPOSE management software sets up the web links. Click the web links icon

on the top left corner, and goes access to RGBlink website.

Connect Setting

The remote controller PC which runs XPOSE connects with Flex RS1 by the USB to

the RS 232 converter and the RS 232 to RJ45 cable (with the standard accessories).

12/27

System Setting

Click “System Setting” in the main interface:

!

1. Connect Setting

Click “Connect Setting”: Select ”COM Port” and “Baud Rate”, click the drop down

arrow after them, and click “OK”.

Setting the device connecting ways: Serial Connect, Ethernet Connect and

Search by this configuration.

13/27

After setting ”COM Port” and “Baud Rate”, pop-up window as follows:

2. IP Settings

Click the “IP Settings”, and pop-up window as follows:

Default “Auto get IP address”. Users can also set IP address, Mask and GateWay

manually. This is usually used if one computer control some devices or remote

control. It takes effect after reboot the software if change IP through network.

14/27

3. System Information

Click “System Information”, and pop-up window as follows:

Display the device version information. Including Model Number, Serial Number, IP

Address, firmware version, etc.

4. Factory Reset

Click “Factory Reset”, and pop-up window as follows:

Click “OK” or “Cancel” to confirm the reset.

15/27

5. Fan Control

Click “Fan Control”, and pop-up window as follows:

Enable or disable the Auto Fan Control, set Fan Speed and click ”Set”, that will

load.

Input Settings

Click the “Input Settings”, and enter the interface as follows:

!

16/27

1. 4K Input Set

Click the “4K Input Set”, and pop-up window as follows:!

!

Click “Work Mode”, click the drop down arrow after the Mode, and select “4K x

2K” or “4K x 1K” or “2K x 1K”.

Click Input 1 Type Including Dual DVI, HDMI 1.4, HDMI 2.0, DP 1.2; Then, click “set”.

Output Settings

Click the “Output Settings”, and enter the interface as follows:

!

17/27

1.Test Pattern

Click the “Test Pattern”, and pop-up window as follows:

!

Click “Output”, click the drop down arrow and select any Ports among the four

boards.

!

Click “Color Choose”, click the drop down arrow and select any color among the

sixteen boards.

!

18/27

2. DE Setting

Click the “DE Setting”, and pop-up window as follows:

!

Brightness: The brightness adjustment range is between 0~128. Click “Set” to

confirm.

DE: User can select one port or all ports, and enable the DE function by sliding the

DE Switch. The settings for DE include X, Y, width, height, line polarity and scene

polarity. Vertical spliting can be selected in “Output Port”.

Operation Mode

Click the “Operation Mode”, and enter the interface as follows:

There is 3 working modes, including the Video Wall mode, Rotation mode and

Blending Mode.

19/27

Independent Mode, Rotation Mode and Projection Mode are included in

operation mode, specific as follows:

1. Independent Mode

Click the “Independent Mode”, and enter to the interface as follows:! !

!

Layer 1~4: X, Y for Layer position, W, Y is Layer size.

There are two ways can change the size and location of the layer:

a. Drag the layer by mouse: click the right window, select any layer, press the rim

of the layer with mouse to drag the size, release the mouse, click the layer again,

and press the mouse to drag the layer to suitable position.

b. Choose number directly: click the left or right window, select any layer and

choose any number as X, Y, W, H to ensure accurate position and size.

Output Setting

Click the Output Settings shortcut and pop-up window as follows:

20/27

Click “port”, click drop down arrow and select any port among the four boards.

This mode allow set each port resolution independently.

Click “resolution”, click drop down arrow and select any resolution among the

sixteen boards.

Width, Height and Frequency can be set.

Page is loading ...

RGBlink FLEX RS1 Quick start guide

RGBlink FLEX RS1 Quick start guide

Related papers

Other documents