Rockwell Automation Allen-Bradley ClearMark Quick start guide

Brand: Rockwell Automation

Model: Allen-Bradley ClearMark

Type: Quick start guide

QUICK START

Bulletin 1492 Allen-Bradley ClearMark™ Printer

Table of Contents

Introduction

This guide provides the basic information required to start up your ClearMark printer. For

detailed information on specific product features or configurations, refer to the ClearMark

printer user manual, publication 1492-UM008*-EN-P. Read this guide carefully before you

use the ClearMark printer and retain it for future reference.

Section Page

Unpacking and Inspecting 2

Installation Requirements 3

Preparing the System 3

Driver and Software Installation 5

Calibrating the ClearMark Printer 8

Printing with the ClearMark Printer 13

Unpacking and Inspecting

Figure 1 - Removing the Printer from Packaging

1. Take printer out of box

2. Remove protective foam

3. Place on a flat, stable surface

4. Check the delivery contents:

–Printer

–Power cord

–USB cable

– Quick Start Guide (this document)

–ClearMark Printer user manual

–ClearTools™ Software user manual

– Printer driver and ClearTools

software CD

– Two marker cards (Cat. No. 1492-M5X5)

–Output rail

Grips

ATTENTION: Printer weight is

approximately 65 lb. Always use

two people and make use of the

grips when moving.

Installation Requirements

• Operating Temperature: +68…95 °F (+20…35 °C)

•Power Source:

– Cat No. 1492-PRINT110: 100...120V, 50/60 Hz, 8 A

– Cat. No. 1492-PRINT220: 220...240V, 50/60 Hz, 4 A

Figure 2 - Printer Overview and Clearance Requirements - in. (mm)

Preparing the System

Figure 3 - Insert output rail

1. Insert the output rail

Maintenance Cover for Printing System

Ink Cartridge Cover

Operating and Control Panel Display

Maintenance Cover

for Waste Pad

Output Rail

Loader - Input

9.84”

(250 mm)

7.87”

(100 mm)

9.84”

(250 mm)

3.94”

(100 mm)

3.94”

(100 mm)

Figure 4 - Load marker cards

2. Load the marker cards into the printer (see picture on printer for

insertion)

Figure 5 - Power and data connections

3. Make the necessary power and data connections.

ATTENTION: Do not

open the printer covers

during operation

Power

Cord

USB

Cable

Network Cable

(if desired)

Driver and Software Installation

Figure 6 - Language Selection

1. Insert the “Printer Driver and Soware” CD into your CD drive. e

CD starts automatically, If not, locate setup.exe found on the CD.

2. Please select your language and conrm by clicking the [

] button.

Figure 7 - Printer Driver Installation

1. First install the printer driver.

a. Select Install→Printer Driver→ClearMark Printer→

32 bit: Vista/XP/Win2000/Windows 7 or

64 bit: Windows Vista/Windows 7

2. Accept the license agreement and click [Next].

3. Choose “Connect with USB cable” and click [Next].

4. Confirm that the printer is off and click [Next].

5. Turn on the printer.

6. Click [No] for default printer.

7. Choose “Never display status monitor” and click [Next].

Figure 8 - Status Monitor

8. Click [Finish]. The driver is now installed.

9. Next, Install ClearTools soware.

a. Select Install→Soware→ClearTools→Vista/XP/Win2000/Windows 7

Figure 9 - Software Installation

10. Click [Next].

11. Accept the license agreement and click [Next].

12. Click [Next].

13. Click [Install].

14. Click [Finish]. e ClearTools soware is now installed.

Calibrating the ClearMark Printer

Note: Affects all Cards

1. To open ClearTools, Go to Start→Programs→Rockwell Automation→

ClearTools→ClearTools.

2. Double click on "1492-M5X5" in the variant list.

3. In the first column, 5 marker tags down, place a capital "X" as shown.

See Figure 10. Note: It is critical to select this tag.

Figure 10 -

4. On the display on the top of the printer, press the “Heating 1 and

Heating 2” buttons so that the LED lights are off.

a. The printed card can be cleaned with water and used again.

b. The distances required for calibrating the printer are not distorted by

the heat effects.

5. Select File→Print.

6. In the pull down menu select GelSprinter GX3000/3050N printer .

See Figure 11.

Figure 11 -

7. Click [Map]. (The 1492-M5X5 is now linked to this printer)

8. Click [OK], with the "As Printer" selected. See Figure 11.

9. Click [Calibration].

10. Verify a value of "7" in the box marked "Left" and a "66" in the box

marked "To p ". See Figure 12.

11. Click [Save].

Figure 12 -

12. Load the 1492-M5X5 card.

13. Click “Print”. (Pop-up window appears: leave heat off and click [OK].)

14. If the "X" is centered, proceed to step 19.

15. If the "X" is not centered. Go to File -> Print, and Click [Calibration].

16. See Figure 13 for horizontal adjustments.

17. See Figure 14 for vertical adjustments.

Note: When making adjustments use maximum increments of 0.5 mm.

18. After making a change, Click [Save]. Then click [Print] to check the

card.

a. If centered go to step 19, If not go back to step 15.

Figure 13 -

Figure 14 -

If “X” appears

on this half of

the card

increase the

“Left” number

to move it back

to center.

If “X” appears

on this half of

the card

decrease the

“Left” number

to move it back

to center.

If “X” appears on this half of

the card increase the “Top” number

to move it back to center.

If “X” appears on this half of

the card decrease the “Top” number

to move it back to center.

19. Place a capital "X" in the upper right corner as shown See Figure 15 .

You can leave the "X" in the first column because it will not move with

these upcoming changes.

20. Go to File -> Print, and click [Print].

Figure 15 -

21. If the "X" is centered you are done calibrating and are ready to print. See

section on printing.

22. If the "X" is not centered. Go to File -> Set Printer Correction. See

Figure 16.

Figure 16 -

23. See Figure 17 for horizontal adjustments

24. See Figure 18 for vertical adjustments.

Figure 17 -

Figure 18 -

25. After making changes to the "Width" or "Height", Click [OK]. Then

select File→Print to check the card.

a. If centered move ahead to Printing with the ClearMark printer on

page 13. If not centered go back to Step 22.

If “X“ appears on

this half of the

card decrease

the “Actual Width

)“ number to

move it back to

center.

If “X“ appears on

this half of the

card increase

the “Actual Width

(X)“ number to

move it back to

center.

If “X“ appears on this half of the

card increase the “Actual Height

) “ number to move it back to

center.

If “X“ appears on this half of the

card decrease the “Actual Height

) “ number to move it back to

center.

Printing with the ClearMark printer

1. Select Tools→Product Catalog (or Select File→New).

2. From the product catalog select a desired card (Ex. 1492-M5X10) from

the variant list and double click on it.

Figure 19 -

3. To select all the cells on the marker card hit [Ctrl+A]. (Or select

Edit→Select→All)

Figure 20 -

4. Select the consecutive numbering icon from the toolbar (has 1,2,3 on it)

or hit[F8] on the keyboard. See Figure 20.

Figure 21 - Consecutive Numbering

5. Click [OK] and the card will be numbered 1 through 144. See

Figure 21

Figure 22 -

6. If desired the direction of the text can be changed, by clicking the

orientation icons. See Figure 22

7. Select File -> Print

8. In the pull down menu select the GelSprinter GX 3000/3050N printer

driver.

9. Click [Map].

Note: Every time you are printing a new type of marker card for the first

time, you must map the printer prior to printing.

10. Click [Print] to print the marked card.

Figure 23 -

Publication 1492-QS002B-EN-P - October 2011

Allen-Bradley, Listen. Think. Solve., Rockwell Automation, Rockwell Software, ClearMark, and ClearTools are trademarks of

Rockwell Automation, Inc.

Rockwell Automation Allen-Bradley ClearMark Quick start guide

Brand: Rockwell Automation

Model: Allen-Bradley ClearMark

Type: Quick start guide

Download PDF

report

Rockwell Automation Allen-Bradley ClearMark Quick start guide

Rockwell Automation Allen-Bradley ClearMark Quick start guide

Related papers

Other documents