Paradyne 3166 DSU Reference guide

Brand: Paradyne

Model: 3166 DSU

Category: Networking

Type: Reference guide

ACCULINK 3166 DSU/CSU

QUICK REFERENCE

Document No. 3166-A2-GL11-10

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be

copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated

into any human or computer language in any form or by any means, electronic,

mechanical, magnetic, manual or otherwise, or disclosed to third parties without the

express written permission of Paradyne Corporation, 8545 126th Ave. N.,

Largo, FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the

contents hereof and specifically disclaims any implied warranties of merchantability or

fitness for a particular purpose. Further, Paradyne Corporation reserves the right to

revise this publication and to make changes from time to time in the contents hereof

without obligation of Paradyne Corporation to notify any person of such revision or

changes.

Changes and enhancements to the product and to the information herein will be

documented and issued as a new release to this manual.

Warranty, Sales, and Service Information

Contact your local sales representative, service representative, or distributor directly for

any help needed. For additional information concerning warranty, sales, service, repair,

installation, documentation, training, distributor locations, or Paradyne worldwide office

locations, use one of the following methods:

 Via the Internet: Visit the Paradyne World Wide Web site at

http://www.paradyne.com

 Via Telephone: Call our automated call system to receive current information via

fax or to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Trademarks

All products and services mentioned herein are the trademarks, service marks,

registered trademarks or registered service marks of their respective owners.

Document Feedback

We welcome your comments and suggestions about this document. Please mail them

to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,

or send e-mail to [email protected]. Include the number and title of this

document in your correspondence. Please include your name and phone number if you

are willing to provide additional clarification.

ACCULINK 3166 DSU/CSU

Quick Reference

Document Number 3166-A2-GL11-10

November 1998

Product Documentation on the World Wide Web

Complete documentation for this product is available at www.paradyne.com.

Select

Service & Support

→

Technical Manuals

→

T1/E1 Digital Access Devices.

Select the following document:

3166-A2-GB20

ACCULINK 3166 DSU/CSU User’s Guide

To request a paper copy of a Paradyne document:

 Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

 Outside the U.S.A., call 1-727-530-8623

Before installing your DSU/CSU, read the

Important Safety Instructions

on page 15.

Quick Start Procedure

The following procedure is for experienced DSU/CSU users who are familiar with the

3166 DSU/CSU installation process and have no special requirements for their

application. See the

ACCULINK 3166 DSU/CSU User’s Guide

for more information.

1. Install the rear connector module loosely onto the 3000 Series Carrier. Do not

tighten the screw.

98-16083

3000 Series

Carrier

Slots

Tabs

Rear

Connector

Module

NOTE:

If an auxiliary backplane for Models 3151 or 3161 DSUs is installed in the

same carrier, verify that it is mounted over slots 9–16. Slot 9 is rendered

inaccessible if the auxiliary backplane is mounted over slots 1–8.

2. Insert the DSU/CSU circuit card into the appropriate slot in the carrier and lock the

latch.

Circuit

Card

Guides

Circuit

Pack

Lock

Latch

Open

(Unlocked)

Closed

(Locked)

495-14813

3. Tighten the screw on the rear connector module.

4. Attach a modular cable (not included) to the COM connector of the rear connector

module. (See the

User’s Guide

for detailed cable and connector information.)

Connect the other end to a terminal or PC.

5. Attach the DB25 port cable to the PORT 1 connector on the rear connector module.

Connect the other end of the cable to the customer premises equipment.

6. Attach the network cable to the Network connector on the rear connector module.

Connect the other end of the network cable to the connection provided by the

telephone company.

7. To daisy-chain the diagnostic channel with that of other 3166 DSU/CSUs or a T1

auxiliary backplane, insert one end of the short diagnostic channel extension cable

into either DIAGNOSTIC CHANNEL connector on the rear connector module.

Insert the other end into either DIAGNOSTIC CHANNEL connector of a

neighboring 3166 rear connector module, or the diagnostic channel connector of a

T1 auxiliary backplane.

98-16080

PORT

CLOCK IN

DIAGNOSTIC

CHAN

PORT

DTE

DTE DTE DTE DTE DTE DTE

DTE

SLT 8 (16)

SLOT 6 (14)

SLOT 7 (15)

SLOT 5 (13)

SLOT 4 (12) SLOT 3 (11)

SLOT 2 (10)

SLOT 1 (9)

T1 NETWORK

INTERFACE

COMCODE

107170409

MODEL NO.

3100-F1-900

DIAGNOSTIC

CHAN

CAUTION:

DISCONNECT ALL TELEPHONE LINES AT THE NETWORK

INTERFACE BEFORE TOUCHING OR SERVICING

Diagnostic Channel

Extension Cable

NET

PORT 1

COM

DIAGNOSTIC

CHANNEL

NET

PORT 1

COM

DIAGNOSTIC

CHANNEL

The power-up self-test begins when power is applied. During the power-up self-test, the

Fail LED flashes, then all LEDs blink twice. When the test is complete, verify that the

DSU/CSU is functional by observing that the OK and NET Sig LEDs are lit.

The Factory 1 configuration for ESF framing format and B8ZS line coding format is the

default configuration and is appropriate for most networks. If this configuration does not

work for you, try the Factory 2 configuration for D4 framing format and AMI line coding

format. To further customize configuration options, refer to

Changing Configuration

Options

in Chapter 3,

Operation

, and Appendix C,

Configuration Options

, in the

ACCULINK 3166 DSU/CSU User’s Guide

Configuration Options

Configuration options are accessed from the Cnfig branch of the front panel menu.

DSU ESF

Stat

98-16084-01

DevHS

STest Perf TStat LED ID

T1 Prt1Prt1UserTelco

Cur

24Tot

Intvl

FarNear

Cur

8Tot

Intvl

Test

Rlpbk Lpbk Ptrns Lamp

QRSS 511

Abort Mon

LLBUP

LLBDN

54UP

54DN

FT1UP

FT1DN

PLB RLBLLBAbort DCLB DTLB

QRSS1in8 511

Send

Cnfig Ctrl

Rel

ClrReg

Reset

CID

Passwd

ACO

Call

Load Edit Area From:

Choose Function:

Activ Cust1 Cust2 Fact1 Fact2

User AlarmNETPrt1 Chan Gen Mgmt

Gen Trap

Prt1ClearDsply

Save

Cust1Activ Cust2

Edit

User Prt1

FarNear

DiscDial ChDir

1 . . 5,A

(Directory)

1 . . 5,A

(Directory)

Available only if a device

failure has occured.

Clear

Table 1. Port Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

E530 E530

Port Type:

V.35 V.35

Selects the

ort ty

e: EIA

530A,

Port Type:

RS449 RS449

e por

ype:

EIA

530A

V.35, RS449, or X.21.

X.21 X.21

BRt

Nx64 Nx64

Enables the port to either Nx56 or

Base Rate:

Nx56 Nx56

Enables

the

ort

either

Nx56

Nx64 rates.

Disab Disab

N t DCLB

V.54 V.54

Network-initiated DCLB, allows

DCLB b ll d b i b d

Net DCLB:

FT1 FT1

DCLB to be controlled by inband

V.54 or FT1 (ANSI) codes.

Both Both

()

Disab Disab

Port LB:

DTLB DTLB

Port-initiated Loopbacks, allows

L b k t b i iti t d th h

Port LB:

DCLB DCLB

Loopbacks to be initiated through

the port by the external DTE.

Both Both

Disab Disab

All Ones:

DTR DTR

All ones sent to network

(

DTE

)

All Ones:

RTS RTS

All

ones

sent

network

(DTE)

when DTR or RTS interrupted.

Both Both

Rcv Yellow:

None None

Data port remains enabled, or is

di bl d i i Y ll

Rcv

Yellow:

(Received Yellow)

Halt Halt

disabled, on receiving Yellow on

network T1.

Tx Clock:

Int Int

Selects whether the transmitted

d t l k i i t l (TXC)

Tx Clock:

Ext Ext

data clock is internal (TXC) or

external (XTXC).

InvertTxC:

Enab Enab

Selects phase inversion of the

InvertTxC:

(Invert Tx Clock)

Disab Disab

Selects

hase

inversion

the

transmit clock (TXC).

InvertData:

Enab Enab

Allows the data on the port to be

InvertData:

Disab Disab

Allows

the

data

the

ort

inverted.

EDL:

Enab Enab

Specifies whether the Embedded

EDL:

Disab Disab

S ecifies

whether

the

Embedded

Data Link is enabled.

Table 1. Port Configuration Options (2 of 2)

Option Comments/DescriptionFactory 2Factory 1

10E–4 10E–4

10E–5 10E–5

Err Rate:

(E i E

10E–6 10E–6

Selects the error rate threshold for

EiERtAl

(Excessive Error

Rate)

10E–7 10E–7

Excessive Error Rate Alarm.

)

10E–8 10E–8

10E–9 10E–9

Disab Disab

Near end:

Maint Maint

Specifies whether the device will

iti d f

Near-end:

Send Send

maintain near-end performance

statistics.

Both Both

Far end:

Disab Disab

Specifies whether the device will

iti f d f

Far-end:

Maint Maint

maintain far-end performance

statistics.

Mgmt Link:

Enab Enab

Specifies whether the EDL

Mgmt Link:

Disab Disab

S ecifies

whether

the

EDL

Management Link is enabled.

Table 2. Network Interface Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

NET Framing:

D4 D4

Selects D4 or ESF framing format

NET Framing:

ESF ESF

Selects D4 or ESF framing format.

NET Coding:

AMI AMI

Selects AMI or B8ZS line coding

NET Coding:

B8ZS B8ZS

Selects

AMI

B8ZS

line

coding

format.

0.0 0.0

LBO:

–7.5 –7.5

Provides Line Build Out in dB

LBO:

–15 –15

Provides Line Build Out in dB.

–22.5 –22.5

ANSI PRM:

Enab Enab

Sends ANSI Performance Report

ANSI PRM:

Disab Disab

Sends

ANSI

Performance

Re ort

Messages.

Mgmt Link:

Enab Enab

Specifies whether the FDL’s

Mgmt Link:

Disab Disab

S ecifies

whether

the

FDLs

Management Link is enabled.

Table 2. Network Interface Configuration Options (2 of 2)

Option Comments/DescriptionFactory 2Factory 1

NET LLB:

Enab Enab

Network-initiated LLB allows LLB to

NET LLB:

Disab Disab

Network initiated

LLB

allows

LLB

be controlled by inband LLB codes.

NET PLB:

Enab Enab Network-initiated PLB allows PLB

to be controlled by FDL PLB

NET PLB:

Disab Disab

to be controlled by FDL PLB

messages.

(Not available

62411

Provides enforcement of ones

d i i AT&T TR

BitStuff:

ava

when Net Coding

Part68

density protection per AT&T TR

62411, ANSI T1

403, and FCC

is B8ZS)

Disab

62411

ANSI

403

, an

FCC

Part 68 Technical Publication.

Circuit Ident:

Edit Edit

Specifies the transmission vendor’s

Circuit

Ident:

Clear Clear

S ecifies

the

transmission

vendor s

circuit identifier.

Table 3. General Configuration Options

Option Factory 1 Factory 2 Comments/Description

NET NET

Clock Src:

Prt1 Prt1 Selects the clock source to be

dth tlkfth

Clock Src:

Int Int

used as the master clock for the

DSU/CSU.

Ext Ext

SU/CSU

TstTimout:

Enab Enab

Specifies whether the durations of

i iti t d t t li it d b

TstTimout:

Disab Disab

user-initiated tests are limited by

Tst Duration.

10 10

TstDuration:

Up Up

Specifies the duration of

iii dl b k d

ura

on:

Down Down

user-initiated loopback and pattern

tests.

Save Save

Table 4. User Configuration Options (1 of 3)

Option Factory 1 Factory 2 Comments/Description

Self Test:

Enab Enab

Allows b

pass of self-test on

Self-Test:

Disab Disab

Allows

by ass

self-test

initialization.

Dial In:

Enab Enab

Controls whether dial-in access is

Dial-In:

Disab Disab

Controls

whether

dial in

access

allowed.

Password:

None None

Controls whether a password is

Password:

Com Com

Controls

whether

assword

required for remote access.

Com Port:

Enab Enab

Controls whether the COM port is

Com Port:

Disab Disab

Controls

whether

the

COM

ort

enabled or disabled.

Mgmt Mgmt

Com Use:

ASCII ASCII

Controls how the COM port is

used.

Term Term

used

Disab Disab

ComExtDev:

AT AT

Specifies the type of external

commands allowed.

Other Other

commands

allowed

ComConnPrefix:

Edit Edit

Controls the COM port’s connect

ComConnPrefix:

Clear Clear

Controls

the

COM

orts

connect

prefix.

ComConnected:

Edit Edit

Controls the COM port’s connect

ComConnected:

Clear Clear

Controls

the

COM

orts

connect

indication string.

ComEsca

eSeq:

Edit Edit

Controls the COM port’s escape

ComEscapeSeq:

Clear Clear

Controls

the

COM

orts

esca e

sequence.

None None

0.2s 0.2s

ComEscDel:

0.4s 0.4s

Controls the COM port’s escape

ComEscDel:

0.6s 0.6s

Controls

the

COM

orts

esca e

sequence delay.

0.8s 0.8s

1.0s 1.0s

ComDisconnect:

Edit Edit

Controls the COM port’s

ComDisconnect:

Clear Clear

Controls

the

COM

orts

disconnect string.

Table 4. User Configuration Options (2 of 3)

Option Comments/DescriptionFactory 2Factory 1

1.2 1.2

2.4 2.4

Com Rate:

(C i ti P t

4.8 4.8

Selects the bit rate for the COM

(Communication Port

Rate)

9.6 9.6

Selects

the

bit

rate

for

the

COM

port.

ae)

14.4 14.4

19.2 19.2

Char Length:

7 7

Selects the character len

th for the

Char Length:

8 8

Selects

the

character

length

for

the

COM port.

CParity:

None None

CParity:

(Communication Port

Pit)

Even Even

Selects the parity for the COM port.

(

Parity)

Odd Odd

CSto

Bits:

1 1

CStop Bits:

(Communication Port

1.5 1.5

Selects the number of stop bits for

the COM

ort.

(

Stop Bits)

2 2

the

COM

port

Ignore DTR:

Yes Yes

Specifies whether the COM port

Ignore DTR:

No No

S ecifies

whether

the

COM

ort

ignores DTR.

CmInActTm:

(COM P t I ti it

Enab Enab

Specifies whether the

i ti t di t

(COM Port Inactivity

Timeout)

Disab Disab

communication port disconnects

after a certain period of inactivity.

5 5

CmDiscTm:

(COM Port

Up Up

Specifies the period of inactivity

(1 to 60 minutes) that causes a

(COM

Port

Disconnect Time)

Down Down

minutes)

that

causes

disconnect if CmInActTm is

enabled.

Save Save

enabled

TnSession:

Enab Enab

Specifies whether the DSU/CSU

dtTl t i

TnSession:

(Telnet Session)

Disab Disab

responds to Telnet session

requests.

TnPaswd:

Enab Enab

Specifies whether a password is

TnPaswd:

(Telnet Password)

Disab Disab

S ecifies

whether

assword

required for Telnet sessions.

Table 4. User Configuration Options (3 of 3)

Option Comments/DescriptionFactory 2Factory 1

TnInActTm:

(T l t I ti it

Enab Enab

Specifies whether a Telnet session

di t ft t i i d

(Telnet Inactivity

Timeout)

Disab Disab

disconnects after a certain period

of inactivity.

5 5

TnDiscTm:

(Telnet Disconnect

Up Up

The period of inactivity (1 to

60 minutes) that causes a

(Telnet

Disconnect

Time)

Down Down

minutes)

that

causes

disconnect if TnInActTm is

enabled.

Save Save

enabled

Table 5. Alarm Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

Al M

Disab Disab Does not display alarm messages.

Alrm Msg:

Com Com

Sends alarm messages to COM

port.

SNMP Trap:

Enab Enab

Sends SNMP traps

SNMP Trap:

Disab Disab

Sends SNMP traps.

TrapDisc:

Enab Enab

Specifies whether the modem

ti ill di t ft

TrapDisc:

Disab Disab

connection will disconnect after a

trap is sent.

DialOut:

Enab Enab

Provides the option to allow

ttidiltt dl

DialOut:

Disab Disab

automatic dial-out to send alarm

messages on the COM port.

Call Retry:

Enab Enab

Specifies whether an outgoing call

i t i d b f il d ll

Call Retry:

Disab Disab

is retried on a busy or failed call

attempt.

Dial Delay:

1–4

6–10

1–4

6–10

The time (in minutes) to delay

between successive alarm

dial-outs or retry attempts.

AltDialDir:

None

1–5

None

1–5

The alternate dial-out directory to

use if a call to the primary number

cannot be completed.

Table 5. Alarm Configuration Options (2 of 2)

Option Comments/DescriptionFactory 2Factory 1

10E–4 10E–4

10E–5 10E–5

Err Rate:

(E i E

10E–6 10E–6

The error rate threshold for

EiERtAl

(Excessive Error

Rate)

10E–7 10E–7

Excessive Error Rate Alarm.

Rate)

10E–8 10E–8

10E–9 10E–9

AlrmRela

Enab Enab

Specifies whether to activate the

AlrmRelay:

(Alarm Relay)

Disab Disab

S ecifies

whether

activate

the

alarm relay on an alarm condition.

Table 6. General Management Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

SNMP Mgt:

Enab Enab

Specifies whether the DSU/CSU

d t SNMP i

SNMP Mgt:

Disab Disab

responds to SNMP session

requests.

NMS Valid:

Enab Enab

Specifies whether the DSU/CSU

validates the IP address of an

NMS Valid:

Disab Disab

validates

the

address

SNMP manager attempting

access.

Num Sec Mgrs:

1 1

The number of SNMP mana

ers

Num Sec Mgrs:

2–10 2–10

The

number

SNMP

managers

allowed to access the DSU/CSU.

NMS

IP Adr:

Edit Edit

Allows you to define or clear the

ll bl IP dd f SNMP

NMS

IP Adr:

Clear Clear

allowable IP address of an SNMP

manager.

NMS

Acs:

Read Read

The type of access allowed for an

SNMP i it

NMS

Acs:

R/W R/W

SNMP manager using community

name 1.

System Name:

Edit Edit

The SNMP s

stem name for this

System Name:

Clear Clear

The

SNMP

system

name

for

this

device.

System Location:

Edit Edit

The SNMP s

stem location for this

System Location:

Clear Clear

The

SNMP

system

location

for

this

device.

Table 6. General Management Configuration Options (2 of 2)

Option Comments/DescriptionFactory 2Factory 1

System Contact:

Edit Edit

The SNMP s

stem contact name

System Contact:

Clear Clear

The

SNMP

system

contact

name

for this device.

CommunityName1:

Edit Edit

A community name that is allowed

t thi d i D f lt t

CommunityName1:

Clear Clear

access to this device. Defaults to

public

Access 1:

Read Read

The t

pe of access allowed for

Access 1:

R/W R/W

The

ty e

access

allowed

for

community name 1.

Comm nit Name2

Edit Edit

A communit

name that is allowed

CommunityName2:

Clear Clear

community

name

that

allowed

access to this device.

Access 2:

Read Read

The t

pe of access allowed for

Access 2:

R/W R/W

The

ty e

access

allowed

for

community name 2.

Com IP Adr:

Edit Edit

The IP address for the COM port

Com IP Adr:

Clear Clear

The

address

for

the

COM

ort

when configured for SNMP.

Com NetMask:

Edit Edit

The Subnet Mask needed to

th d i h th COM

Com NetMask:

Clear Clear

access the device when the COM

port is configured for SNMP.

Com Link:

PPP PPP

The link la

er protocol for the COM

Com Link:

SLIP SLIP

The

link

layer

rotocol

for

the

COM

port when configured for SNMP.

Table 7. Management Trap Configuration Options

Option Factory 1 Factory 2 Comments/Description

Num Trap Mgrs:

2–6

The number of trap managers

supported by the device.

Trap

IP Adr:

Edit Edit

Specifies the IP address for each

trap mana

er. This confi

uration

Trap

IP Adr:

Clear Clear

tra

manager

This

configuration

option is repeated for all

managers.

None None

IPBus IPBus

Trap

Dst:

Com Com

Specifies the network destination

for Tra

Manager

FDL FDL

for

Trap

Manager

EDL1 EDL1

Disab Disab

Gen Trap:

Warm Warm Specifies the general trap types to

bl W St t A th ti ti

Gen Trap:

Auth Auth

enable: WarmStart, Authentication

Failure or both.

Both Both

aueobo

Entp Trap:

Enab Enab

Specifies whether the

E t i S ifi t t i

Entp Trap:

Disab Disab

EnterpriseSpecific trap type is

enabled.

Disab Disab

Link Trap:

Up Up Specifies the link trap type to

bl T LikU Lik

Link Trap:

Down Down

enable: Trap on Link Up, Link

Down, or both.

Both Both

o,obo

NET NET

When any link trap types are

Trap I/F:

Port Port

When any link trap types are

enabled, specifies which links to

Tra

I/F:

Both Both

send traps for.

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or

included in the manual.

2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable

operation of the product and to protect it from overheating, these slots and

openings must not be blocked or covered.

3. Do not allow anything to rest on the power cord and do not locate the product

where persons will walk on the power cord.

4. Do not attempt to service this product yourself, as opening or removing covers may

expose you to dangerous high voltage points or other risks. Refer all servicing to

qualified service personnel.

5. General purpose cables are provided with this product. Special cables, which may

be required by the regulatory inspection authority for the installation site, are the

responsibility of the customer.

6. When installed in the final configuration, the product must comply with the

applicable Safety Standards and regulatory requirements of the country in which it

is installed. If necessary, consult with the appropriate regulatory agencies and

inspection authorities to ensure compliance.

7. A rare phenomenon can create a voltage potential between the earth grounds of

two or more buildings. If products installed in separate buildings are

interconnected, the voltage potential may cause a hazardous condition. Consult a

qualified electrical consultant to determine whether or not this phenomenon exists

and, if necessary, implement corrective action prior to interconnecting the products.

8. Input power to the ac voltage configuration of this product must be provided by a

UL-listed or CSA-certified power source with a Class 2 or Limited Power Source

(LPS) output. Input power to the dc voltage configurations of this product must be

provided by a National Electric Code (NEC) or a Canadian Electric Code (CEC)

Class 2 circuit.

9. This product contains a coin cell lithium battery that is only to be replaced at the

factory. Caution: There is a danger of explosion if the battery is incorrectly

replaced. Replace only with the same type. Dispose of used batteries according to

the battery manufacturer’s instructions. Attention: Il y a danger d’explosion s’il y a

remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du

même type. Mettre au rebut les batteries usagées conformément aux instructions

du fabricant.

10. In addition, if the equipment is to be used with telecommunications circuits, take the

following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically

designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone

line has been disconnected at the network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm.

There may be a remote risk of electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

EMI Warnings

WARNING:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements

that no modifications will be made to the equipment unless the changes or

modifications are expressly approved by Paradyne Corporation.

WARNING:

To Users of Digital Apparatus in Canada:

This Class A digital apparatus meets all requirements of the Canadian

interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du

règlement sur le matérial brouilleur du Canada.

Government Requirements and Equipment Return

Certain governments require that instructions pertaining to CSU connection to the

telephone network be included in the installation and operation manual. Specific

instructions are listed in the following sections.

Notice to Users of the United States Telephone Network

1. This equipment complies with Part 68 of the FCC rules. On the equipment is a label

that contains, among other information, the FCC registration number for this

equipment. The label is on the 3166 DSU/CSU’s circuit card. If requested, this

information must be provided to the telephone company.

2. The T1 network connection should be made using a Universal Service Order Code

(USOC) type RJ48C jack. The Service Order Code 6.0F should be specified to the

telephone company when ordering the T1 line. In addition, the proper Facility

Interface Code must be specified to the Telephone Company. The DSU/CSU can

be configured to support any of the following framing format and line signaling

techniques. The DSU/CSU’s configuration must correspond to the T1 line’s

parameters.

3166 DSU/CSU Facility Interface Codes

Code

Description

04DU9-BN 1.544 Mbps superframe format (SF) without line power

04DU9-DN 1.544 Mbps SF and B8ZS without line power

04DU9-1KN 1.544 Mbps ANSI ESF without line power

04DU-1SN 1.544 Mbps ANSI ESF and B8ZS without line power

3. If the 3166 DSU/CSU causes harm to the telephone network, the telephone

company will notify you in advance that temporary discontinuance of service may

be required. But if advance notice is not practical, the telephone company will notify

the customer as soon as possible. Also, you will be advised of your right to file a

complaint with the FCC if you believe it is necessary.

4. The telephone company may make changes in its facilities, equipment, operations,

or procedures that could affect the operation of the equipment. If this happens, the

telephone company will provide advance notice in order for you to make the

necessary modifications in order to maintain uninterrupted service.

5. If you experience trouble with this equipment, please contact your sales or service

representative (as appropriate) for repair or warranty information. If the product

needs to be returned to the company service center for repair, contact them directly

for return instructions using one of the following methods:

— Via the Internet: Visit the Paradyne World Wide Web site at

http://www.paradyne.com

— Via Telephone: Call our automated call system to receive current information

via fax or to speak with a company representative.

Within the U.S.A., call 1-800-870-2221

Outside the U.S.A., call 1-727-530-2340

If the trouble is causing harm to the telephone network, the telephone company

may request that you remove the equipment from the network until the problem is

resolved.

6. FCC compliant telephone line cords with modular plugs are provided with this

equipment. This equipment is designed to be connected to the telephone network

or premises wiring using a compatible modular jack which is Part 68 compliant.

Notice to Users of the Canadian Telephone Network

The Industry Canada label identifies certified equipment. This certification means that

the equipment meets telecommunications network protective, operational and safety

requirements as prescribed in the appropriate Terminal Equipment Technical

Requirements document(s). The Department does not guarantee the equipment will

operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The equipment

must also be installed using an acceptable method of connection. The customer should

be aware that compliance with the above conditions may not prevent degradation of

service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by

the supplier. Any repairs or alterations made by the user to this equipment, or

equipment malfunctions, may give the telecommunications company cause to request

to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of

the power utility, telephone lines and internal metallic water pipe system, if present, are

connected together. This precaution may be particularly important in rural areas.

CAUTION:

Users should not attempt to make such connections themselves, but should

contact the appropriate electric inspection authority, or electrician, as

appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides an

indication of the maximum number of terminals allowed to be connected to a telephone

interface. The termination on an interface may consist of any combination of devices

subject only to the requirement that the sum of the Ringer Equivalence Numbers of all

the devices does not exceed 5.

If your equipment is in need of repair, refer to

Warranty, Sales, and Service Information

in the front of this document.



*3166–A2–GL11–10*

Paradyne 3166 DSU Reference guide

Brand: Paradyne

Model: 3166 DSU

Category: Networking

Type: Reference guide

Download PDF

report

Paradyne 3166 DSU Reference guide

Paradyne 3166 DSU Reference guide

Related papers

Other documents