Paradyne 3165 Reference guide

Brand: Paradyne

Model: 3165

Category: Modems

Type: Reference guide

ACCULINK 3165 DSU/CSU

QUICK REFERENCE

Document No. 3165-A2-GL11-40

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be

copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated

into any human or computer language in any form or by any means, electronic,

mechanical, magnetic, manual or otherwise, or disclosed to third parties without the

express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo,

FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the

contents hereof and specifically disclaims any implied warranties of merchantability or

fitness for a particular purpose. Further, Paradyne Corporation reserves the right to

revise this publication and to make changes from time to time in the contents hereof

without obligation of Paradyne Corporation to notify any person of such revision or

changes.

Changes and enhancements to the product and to the information herein will be

documented and issued as a new release to this manual.

Warranty, Sales, and Service Information

Contact your local sales representative, service representative, or distributor directly for

any help needed. For additional information concerning warranty, sales, service, repair,

installation, documentation, training, distributor locations, or Paradyne worldwide office

locations, use one of the following methods:

 Via the Internet: Visit the Paradyne World Wide Web site at

http://www.paradyne.com

 Via Telephone: Call our automated call system to receive current information via

fax or to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A, call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them

to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,

or send e-mail to [email protected]. Include the number and title of this

document in your correspondence. Please include your name and phone number if you

are willing to provide additional clarification.

Trademarks

All products and services mentioned herein are the trademarks, service marks,

registered trademarks or registered service marks of their respective owners.

ACCULINK 3165 DSU/CSU

Quick Reference

Document Number 3165-A2-GL11-40

November 1998

Product Documentation on the World Wide Web

We provide complete product documentation online. This lets you search the

documentation for specific topics and print only what you need, reducing the waste of

surplus printing. It also helps us maintain competitive prices for our products.

Complete documentation for this product is available at www.paradyne.com.

Select

Service & Support

→

Technical Manuals

→

T1/E1 Digital Access Devices.

Select the following document:

Document No. 3160-A2-GB21

ACCULINK 316x Data Service Unit/Channel Service Unit Operator’s Guide

To request a paper copy of a Paradyne document:

 Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

 Outside the U.S.A., call 1-727-530-8623

Before installing the DSU/CSU, read the

Important Safety Instructions

beginning on

page 17.

Quick Start Procedure

The following procedure is for experienced DSU/CSU users who are familiar with the

3165 DSU/CSU installation process and have no special requirements for their

application. See the

ACCULINK 316x Data Service Unit/Channel Service Unit

Operator’s Guide

for more information.

1. Attach the power cord to the rear of the DSU/CSU and the other end to a grounded

115 Vac power outlet.

2. Attach the 3165 DSU/CSU network connection to the T1 network using the

appropriate cable. Attach the 3165 DSU/CSU to the customer premises equipment

via the port connector.

3. Power on the DSU/CSU to perform the power-up self-test.

4. If you intend to use front panel emulation, connect the cable from the PC to the

COM port on the rear panel of the DSU/CSU.

5. If you intend to manage the 3165 DSU/CSU with SNMP, cable either the COM or

MODEM port (as appropriate for your configuration). Then, configure the SNMP

management link.

6. The Factory 1 configuration for ESF framing format and B8ZS line coding format is

the default configuration and is appropriate for most networks. If this configuration

does not work for you, try the Factory 2 configuration for D4 framing format and

AMI line coding format. To further customize configuration options, refer to

Changing Configuration Options

in Chapter 3,

Operation

, and to Appendix C,

Configuration Options

in the

ACCULINK 316x Data Service Unit/Channel Service

Unit Operator’s Guide

7. During the power-up self-test, the FAIL LED flashes, then all LEDs blink twice.

When the test is complete, verify that the DSU/CSU is functional by observing that

the OK and NETWORK SIG LEDs are lit.

97-15578

PSTN

T1 Network

Modem

Power

Modem

Power

Front

Panel

3165 DSU/CSU

3165

DSU/CSU

3165

DSU/CSU

Serial

Port

COM Port

Network

Port

Modem

Port

COM

Port

Network

Port

Modem

Port

Network

Port

SNMP Manager

Workstation

SNMP Manager

Workstation

CAUTION:

AUX PORT OR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK

AUX PORT

COM PORT MODEM

DTE

POWER

NETWORK

NEC

CLASS 2

INPUT

CAUTION:

AUX PORT OR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK

AUX PORT

COM PORT MODEM

DTE

POWER

NETWORK

NEC

CLASS 2

INPUT

Terminal

T1 or Serial Connections

Dial Connections

Cabling Examples

Configuration Options

Configuration options are accessed from the Configuration branch of the front panel

menu.

DSU ESF

Stat

97-15579

DevHS

STest Perf TSt at LED ID

T1 PrtnPrtnUserTelco

Cur

24Tot

Intvl

FarNear

Cur

8Tot

Intvl

Test

Rlpbk Lpbk Ptrns Lamp

QRSS 511

Abort Mon

LLBUP

LLBDN

54UP

54DN

FT1UP

FT1DN

PLB DLB RLBLLBAbort DCLB DTLB

QRSS 1in8 511

Send

Cnfig Ctrl

Rel

ClrReg

Reset

CID

Passwd

Call

DiscDial ChDir

1 . . 5,A

(Directory)

1 . . 5,A

(Directory)

User Prt1

FarNear

Load Edit Area From:

Choose Function:

Activ Cust1 Cust2 Fact1 Fact2

User AlarmNET Chan Gen Mgmt

Gen Trap

ClearDsply

Save

Cust1Activ Cust2

Edit

Port

Factory default configuration options are shown in boldface type in the following tables.

Table 1. Port Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

E530 E530

Port Type:

V.35 V.35

Selects the

ort t

e: EIA-530A,

Port Type:

RS449 RS449

e por

ype:

EIA

530A

V.35, RS449, or X.21.

X.21 X.21

Base Rate:

Nx64 Nx64

Enables the

ort to either Nx56 or

Base Rate:

Nx56 Nx56

e por

o e

ith

Nx64 rates.

Disab Disab

Net DCLB:

V.54 V.54

Network-initiated DCLB, allows

DCLB to be controlled by inband

Net DCLB:

FT1 FT1

DCLB to be controlled by inband

V.54 or FT1 (ANSI) codes.

Both Both

()

Disab Disab

Port LB:

DTLB DTLB

Port-initiated Loopbacks, allows

Loopbacks to be initiated through

Port LB:

DCLB DCLB

Loopbacks to be initiated through

the port by the external DTE.

Both Both

epo by ee e a

Disab Disab

All Ones:

DTR DTR

All ones sent to network (DTE) T1

All Ones:

RTS RTS

All

ones

sent

network

(DTE)

when DTR or RTS interrupted.

Both Both

Rcv Yellow:

None None

Data port remains enabled, or is

disabled on receiving Yellow on

Rcv

Yellow:

(Received Yellow)

Halt Halt

disabled, on receiving Yellow on

network T1.

Tx Clock:

Int Int

Selects whether the transmitted

data clock is internal (TXC) or

Tx Clock:

Ext Ext

data clock is internal (TXC) or

external (XTXC).

InvertTxC:

Enab Enab

Selects

hase inversion of the

nver

(Invert Tx Clock)

Disab Disab

s p

ase

nvers

on o

transmit clock (TXC).

InvertData:

Enab Enab

Allows the data on the port to be

InvertData:

Disab Disab

Allows

the

data

the

port

inverted.

Table 1. Port Configuration Options (2 of 2)

Option Comments/DescriptionFactory 2Factory 1

10E–4 10E–4

10E–5 10E–5

Err Rate:

(Excessive Error

10E–6 10E–6

Selects the error rate threshold for

Excessive Error Rate Alarm

(Excessive Error

Rate)

10E–7 10E–7

Excessive Error Rate Alarm.

ae)

10E–8 10E–8

10E–9 10E–9

Table 2. Network Interface Configuration Options

Option Factory 1 Factory 2 Comments/Description

NET Framing:

D4 D4

Selects D4 or ESF framing format

NET Framing:

ESF ESF

Selects D4 or ESF framing format.

NET Coding:

AMI AMI

Selects AMI or B8ZS line coding

NET Coding:

B8ZS B8ZS

Selects

AMI

B8ZS

line

coding

format.

0.0 0.0

LBO:

–7.5 –7.5

Provides Line Build Out in dB

LBO:

–15 –15

Provides Line Build Out in dB.

–22.5 –22.5

ANSI PRM:

Enab Enab

Sends ANSI Performance Report

ANSI PRM:

Disab Disab

Sends

ANSI

Performance

Report

Messages.

Mgmt Link:

Disab Disab

Specifies whether the FDL’s

Mgmt Link:

SNMP SNMP

Specifies

whether

the

FDLs

Management Link is enabled.

NET LLB:

Enab Enab

Network-initiated LLB allows LLB to

NET LLB:

Disab Disab

Network-initiated

LLB

allows

LLB

be controlled by inband LLB codes.

NET PLB:

Enab Enab Network-initiated PLB allows PLB

to be controlled by FDL PLB

NET PLB:

Disab Disab

to be controlled by FDL PLB

messages.

62411 62411

Provides enforcement of ones

d it t ti AT&T TR

BitStuff:

Part68 Part68

Provides enforcement of ones

density protection per AT&T TR

62411

ANSI T1-403

and FCC

BitStuff:

Disab Disab

62411

ANSI

403

, an

FCC

Part 68 Technical Publication.

Circuit Ident:

Edit Edit

Specifies the transmission vendor’s

Circuit

Ident:

Clear Clear

Specifies

the

transmission

vendor s

circuit identifier.

Table 3. Channel Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

Block Block

Determines how channels are

Assign By:

ACAMI ACAMI

Determines how channels are

assigned: contiguous blocks,

ACAMI i di id l h l

Assign By:

Chan Chan

assigned: contiguous blocks,

ACAMI or individual channels.

Port Rate:

64 (56)

128 (112)

192 (168)

256 (224)

320 (280)

384 (336)

448 (392)

512 (448)

576 (504)

640 (560)

704 (616)

768 (672)

832 (728)

896 (784)

960 (840)

1024 (896)

1088 (952)

1152 (1008)

1216 (1064)

1280 (1120)

1344 (1176)

1408 (1232)

1472 (1288)

1536 (1344)

64 (56)

128 (112)

192 (168)

256 (224)

320 (280)

384 (336)

448 (392)

512 (448)

576 (504)

640 (560)

704 (616)

768 (672)

832 (728)

896 (784)

960 (840)

1024 (896)

1088 (952)

1152 (1008)

1216 (1064)

1280 (1120)

1344 (1176)

1408 (1232)

1472 (1288)

1536 (1344)

Selects the data rate for the port.

The possible rates depend on

whether the port is configured for

Nx56 or Nx64.

This configuration option only

appears if the “Assigned By”

configuration option is Block or

ACAMI.

Table 3. Channel Configuration Options (2 of 2)

Option Factory 1 Factory 2 Comments/Description

Clear Clear

Clears (unassigns) channels for

this port.

Start At:

N1 (D1)

N2 (D2)

N3 (D3)

N4 (D4)

N5 (D5)

N6 (D6)

N7 (D7)

N8 (D8)

N9 (D9)

N10 (D10)

N11 (D11)

N12 (D12)

N13 (D13)

N14 (D14)

N15 (D15)

N16 (D16)

N17 (D17)

N18 (D18)

N19 (D19)

N20 (D20)

N21 (D21)

N22 (D22)

N23 (D23)

N24 (D24)

N1 (D1)

N2 (D2)

N3 (D3)

N4 (D4)

N5 (D5)

N6 (D6)

N7 (D7)

N8 (D8)

N9 (D9)

N10 (D10)

N11 (D11)

N12 (D12)

N13 (D13)

N14 (D14)

N15 (D15)

N16 (D16)

N17 (D17)

N18 (D18)

N19 (D19)

N20 (D20)

N21 (D21)

N22 (D22)

N23 (D23)

N24 (D24)

This configuration option appears if

the “Assigned By” configuration

option is Block or ACAMI.

Line 1 Displays: Line 2 Displays: Meaning Comments/Description

— Unassigned

N1 N2 N3 ...... N24:

Prt1

Channel assigned

to port 1

This configuration option appears if

the “Assigned By” configuration

option is individual channels

......

N24:

(If assigned to NET)

D1 D2 D3 ..... D24:

(If assigned to DTE)

D1, D2 ... D24

Channel assigned

to this DTE

channel

gyg

option is individual channels

(Chan).

Function key under the channel

(N1 N2 t ) i ( i )

(If assigned to DTE)

N1, N2 ... N24

Channel assigned

to this NET

channel

Function

key

under

the

channel

(N1, N2 etc.) assigns (unassigns)

port (1, 2, 3, or 4) to that channel.

Table 4. General Configuration Options

Option Factory 1 Factory 2 Comments/Description

Gen Yellow:

Enab Enab

Yellow alarm is

enerated b

the

ow:

(Generate Yellow)

Disab Disab

ow a

arm

s genera

DSU/CSU on LOS, LOF, or AIS.

NET NET

DTE DTE

Selects the clock source to be

Clock Src:

Prt1 Prt1

Selects the clock source to be

used as the master clock for the

DSU/CSU

Clock Src:

Int Int

used as the master clock for the

DSU/CSU.

Ext Ext

2048 2048

Clock Rate:

1544 1544

Selects the clock rate of the source

if external.

Clock Rate:

8 8

erna

Tst Timeout

Enab Enab

Specifies whether the durations of

user initiated tests are limited by

Tst Timeout

Disab Disab

user-initiated tests are limited by

Tst Duration.

10 10

Tst Duration

Up Up

Specifies the duration of

iii dl b k d

Tst Duration

Down Down

Specifies

the

duration

user-initiated loopback and pattern

tests.

Save Save

tests

Table 5. User Configuration Options (1 of 3)

Option Factory 1 Factory 2 Comments/Description

Self

Test:

Enab Enab

Allows bypass of self-test on

Self-Test:

Disab Disab

Allows

bypass

self

test

initialization.

FP Access:

Enab Enab

Controls whether front panel

FP Access:

Disab Disab

Controls

whether

front

panel

access or display is allowed.

FP Pass:

Enab Enab

Controls whether front panel

FP Pass:

Disab Disab

Controls

whether

front

panel

pass-through is allowed.

Dial

In:

Enab Enab

Controls whether dial-in access is

Dial-In:

Disab Disab

Controls

whether

dial-in

access

allowed.

None None

Password:

Com Com

Controls whether a password is

Password:

Modem Modem

Controls

whether

password

required during a call setup.

Both Both

Mgmt Mgmt

Com Use:

ASCII ASCII

Controls how the COM port is

Com Use:

Daisy Daisy

Controls

how

the

COM

port

used.

Term Term

Com Type:

Async Async

Controls whether the COM port is

Com Type:

Sync Sync

Controls

whether

the

COM

port

synchronous or asynchronous.

Com Clk:

Int Int

Controls whether the COM port

Com Clk:

Ext Ext

Controls

whether

the

COM

port

uses an internal or external clock.

1.2 1.2

2.4 2.4

Com Rate:

4.8 4.8

Com Rate:

(Communication Port

Rt)

9.6 9.6

Selects the bit rate for the COM

ort.

(Communication Port

Rate)

14.4 14.4

por

19.2 19.2

38.4 38.4

Char Length:

7 7

Selects the character length for the

Char Length:

8 8

Selects

the

character

length

for

the

COM port.

CParity:

None None

CParity:

(Communication Port

Parity)

Even Even

Selects the parity for the COM port.

(

Parity)

Odd Odd

py p

Table 5. User Configuration Options (2 of 3)

Option Comments/DescriptionFactory 2Factory 1

CStop Bits:

1 1

CStop Bits:

(Communication Port

St Bit )

1.5 1.5

Selects the number of stop bits for

the COM

ort.

(Communication Port

Stop Bits)

2 2

COM

por

Ignore DTR:

Yes Yes

ecifies whether the COM

ort

Ignore DTR:

No No

pec

ifi

es w

COM

por

ignores DTR.

CmInActTm:

(COM Port Inactivity

Enab Enab

Specifies whether the

communication port disconnects

(COM Port Inactivity

Timeout)

Disab Disab

communication port disconnects

after a certain period of inactivity.

5 5

CmDiscTm:

(

COM Port

Up Up

Specifies the period of inactivity

(

1 to 60 minutes

)

that causes a

(COM

Disconnect Time)

Down Down

)

causes a

disconnect if CmInActTm is

enabled.

Save Save

ena

Mgmt Mgmt

Modem Use:

ASCII ASCII

Controls whether the MODEM port

is used for SNMP mana

ement.

Term Term

s use

SNMP

managemen

Modem Type:

Async Async

Controls whether the MODEM port

Modem Type:

Sync Sync

Controls

whether

the

MODEM

port

is synchronous or asynchronous.

Modem Rate:

1.2 1.2

Selects the bit rate for the MODEM

Modem Rate:

2.4 2.4

Selects

the

bit

rate

for

the

MODEM

port.

MChar Len:

(Modem Port

7 7

Selects the character len

th for the

(Modem Port

Character Length)

8 8

e c

arac

eng

MODEM port.

None None

MParity:

(

Modem Port Parit

Even Even

Selects the parity for the MODEM

ort.

)

Odd Odd

por

MStop Bits:

(Modem Port Stop

1 1

Selects the number of stop bits for

(Modem Port Stop

Bits)

2 2

Selects

the

number

stop

bits

for

the MODEM port.

LSpaceDsc:

(Long Space

Enab Enab

Selects the long space disconnect

configuration optionforterminating

(Long Space

Disconnect)

Disab Disab

configuration option for terminating

modem connections.

MoInActTm:

(Modem Port

Enab Enab

Specifies whether the modem port

disconnects after a certain period

(Modem Port

Inactivity Timeout)

Disab Disab

disconnects after a certain period

of inactivity.

Table 5. User Configuration Options (3 of 3)

Option Comments/DescriptionFactory 2Factory 1

5 5

MoDiscTm:

(

Modem Port

Up Up

Specifies the period of inactivity

(1 t 60 i t ) th t

Disconnect Time)

Down Down

Specifies the period of inactivity

(1 to 60 minutes) that causes a

disconnect if MInActTm is enabled.

Save Save

d sco ec c s e abed

TnSession:

Enab Enab

Specifies whether the DSU/CSU

responds to Telnet session

ess

on:

(Telnet Session)

Disab Disab

responds to Telnet session

requests.

TnPaswd:

Enab Enab

ecifies whether a

assword is

asw

(Telnet Password)

Disab Disab

pec

ifi

es w

er a passwor

required for Telnet sessions.

TnInActTm:

(Telnet Inactivity

Enab Enab

Specifies whether a Telnet session

disconnects after a certain period

(Telnet Inactivity

Timeout)

Disab Disab

disconnects after a certain period

of inactivity.

5 5

TnDiscTm:

(

Telnet Disconnect

Up Up

The period of inactivity (1 to

60 minutes

)

that causes a

sconnec

Time)

Down Down

)

causes a

disconnect if TnInActTm is

enabled.

Save Save

ena

Table 6. Alarm Configuration Options

Option Factory 1 Factory 2 Comments/Description

Disab Disab Does not display alarm messages.

Al M

Modem Modem

Sends alarm messages to Modem

port.

Alrm Msg:

Com Com

Sends alarm messages to COM

port.

Both Both

Sends alarm messages to both

ports.

SNMP Trap:

Enab Enab

Sends SNMP traps

SNMP Trap:

Disab Disab

Sends SNMP traps.

TrapDisc:

Enab Enab

Specifies whether the modem

connection will disconnect after a

TrapDisc:

Disab Disab

connection will disconnect after a

trap is sent.

DialOut:

Enab Enab

Provides the option to allow

automatic dial out to send alarm

DialOut:

Disab Disab

automatic dial-out to send alarm

messages on MODEM port.

Call Retry:

Enab Enab

Specifies whether an outgoing call

is retried on a busy or failed call

Call Retry:

Disab Disab

pgg

is retried on a busy or failed call

attempt.

Dial Delay:

1–4

6–10

1–4

6–10

The time (in minutes) to delay

between successive alarm

dial-outs or retry attempts.

AltDialDir:

None

1–5

None

1–5

The alternate dial-out directory to

use if a call to the primary number

cannot be completed.

10E–4 10E–4

10E–5 10E–5

Err Rate:

(Excessive Error

10E–6 10E–6 The error rate threshold for

Excessive Error Rate Alarm

(Excessive Error

Rate)

10E–7 10E–7

Excessive Error Rate Alarm.

Rate)

10E–8 10E–8

10E–9 10E–9

Table 7. Management – General Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

SNMP Mgt:

Disab Disab

Specifies whether the DSU/CSU

responds to SNMP session

SNMP Mgt:

Enab Enab

responds to SNMP session

requests.

NMS Valid:

Disab Disab

Specifies whether the DSU/CSU

validates the IP address of an

NMS Valid:

Enab Enab

validates

the

address

SNMP manager attempting

access.

Num Sec Mgrs:

2–10

The number of management

systems authorized to send SNMP

messages to this unit.

NMS

IP Adr:

Edit Edit

Specifies the IP address for each

NMS This configuration option is

NMS

IP Adr:

Clear Clear

NMS. This configuration option is

repeated for all

NMSs.

NMS

ACS:

Read Read

The type of access allowed for

NMS

ACS:

R/W R/W

The

type

access

allowed

for

NMS

System Name:

Edit Edit

The SNMP system name for this

System Name:

Clear Clear

The

SNMP

system

name

for

this

device.

System Location:

Edit Edit

The SNMP system location for this

System Location:

Clear Clear

The

SNMP

system

location

for

this

device.

System Contact:

Edit Edit

The SNMP system contact name

System Contact:

Clear Clear

The

SNMP

system

contact

name

for this device.

CommunityName1:

Edit Edit

A community name that is allowed

access to this device Defaults to

CommunityName1:

Clear Clear

access to this device. Defaults to

public

Access 1:

Read Read

The type of access allowed for

Access 1:

R/W R/W

The

type

access

allowed

for

community name 1.

CommunityName2:

Edit Edit

A community name that is allowed

CommunityName2:

Clear Clear

community

name

that

allowed

access to this device.

Access 2:

Read Read

The type of access allowed for

Access 2:

R/W R/W

The

type

access

allowed

for

community name 2.

IP Adr:

Edit Edit

The IP address needed to access

IP Adr:

Clear Clear

The

address

needed

access

the device.

NetMask:

Edit Edit

The Subnet Mask needed to

NetMask:

Clear Clear

The

Subnet

Mask

needed

access the device.

Com IP Adr:

Edit Edit

The IP address for the COM port

Com IP Adr:

Clear Clear

The

address

for

the

COM

port

when configured for SNMP.

Table 7. Management – General Configuration Options (2 of 2)

Option Comments/DescriptionFactory 2Factory 1

Com NetMask:

Edit Edit

The Subnet Mask needed to

access the device when the COM

Com NetMask:

Clear Clear

access the device when the COM

port is configured for SNMP.

Com Link:

PPP PPP

The link layer protocol for the COM

Com Link:

SLIP SLIP

The

link

layer

protocol

for

the

COM

port when configured for SNMP.

Modem IP Adr:

Edit Edit

Specifies the IP address for the

MODEM port when configured for

Modem IP Adr:

Clear Clear

MODEM port when configured for

SNMP.

Mdm NetMask:

Edit Edit

Specifies the Subnet Mask needed

to access the device when the

Mdm NetMask:

Clear Clear

access

the

device

when

the

MODEM port is configured for

SNMP.

Alt Mdm IP Adr:

Edit Edit

Specifies the alternate IP address

for the MODEM port when

Alt Mdm IP Adr:

Clear Clear

for the MODEM port when

configured for SNMP.

Alt Mdm NetMask:

Edit Edit

Specifies the alternate modem

Subnet Mask needed to access the

Alt Mdm NetMask:

Clear Clear

Subnet

Mask

needed

access

the

device when the MODEM port is

configured for SNMP.

Modem Link:

PPP PPP Specifies the link layer protocol for

the MODEM port when configured

Modem Link:

SLIP SLIP

pyp

the MODEM port when configured

for SNMP.

None None

Def Netwk:

Com Com

ecifies the default network

Def Netwk:

Modem Modem

pec

ifi

wor

destination.

FDL FDL

Table 8. Management – Trap Configuration Options

Option Factory 1 Factory 2 Comments/Description

Num Trap Mgrs:

2–6

The number of trap managers

supported by the device.

Trap

IP Adr:

Edit Edit

Specifies the IP address for each

trap manager. This configuration

Trap

IP Adr:

Clear Clear

trap

manager

This

configuration

option is repeated for all

managers.

None None

Def Def

Trap

Dst:

Com Com

Specifies the network destination

for Tra

Mana

Modem Modem

rap

anager

FDL FDL

Disab Disab

Gen Trap:

Warm Warm Specifies the general trap types to

enable: WarmStart Authentication

Gen Trap:

Auth Auth

pgpyp

enable: WarmStart, Authentication

Failure or both.

Both Both

Failure

both

Entp Trap:

Enab Enab

Specifies whether the

EnterpriseSpecific trap type is

Entp Trap:

Disab Disab

EnterpriseSpecific trap type is

enabled.

Disab Disab

Link Trap:

Up Up Specifies the link trap type to

enable: Trap on Link Up Link

Link Trap:

Down Down

ppyp

enable: Trap on Link Up, Link

Down, or both.

Both Both

Down

both

NET NET

T1s T1s When any link trap types are

enabled specifies which links to

Trap I/F:

Ports Ports

ypyp

enabled, specifies which links to

send traps for.

All All

send

traps

for

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or

included in the manual.

2. This product is intended to be used with a 3-wire grounding type plug – a plug

which has a grounding pin. This is a safety feature. Equipment grounding is vital to

ensure safe operation. Do not defeat the purpose of the grounding type plug by

modifying the plug or using an adapter.

Prior to installation, use an outlet tester or a voltmeter to check the ac receptacle

for the presence of earth ground. If the receptacle is not properly grounded, the

installation must not continue until a qualified electrician has corrected the problem.

If a 3-wire grounding type power source is not available, consult a qualified

electrician to determine another method of grounding the equipment.

3. Slots and openings in the cabinet are provided for ventilation. To ensure reliable

operation of the product and to protect it from overheating, these slots and

openings must not be blocked or covered.

4. Do not allow anything to rest on the power cord and do not locate the product

where persons will walk on the power cord.

5. Do not attempt to service this product yourself, as opening or removing covers may

expose you to dangerous high voltage points or other risks. Refer all servicing to

qualified service personnel.

6. General purpose cables are provided with this product. Special cables, which may

be required by the regulatory inspection authority for the installation site, are the

responsibility of the customer.

7. When installed in the final configuration, the product must comply with the

applicable Safety Standards and regulatory requirements of the country in which it

is installed. If necessary, consult with the appropriate regulatory agencies and

inspection authorities to ensure compliance.

8. A rare phenomenon can create a voltage potential between the earth grounds of

two or more buildings. If products installed in separate buildings are

interconnected, the voltage potential may cause a hazardous condition. Consult a

qualified electrical consultant to determine whether or not this phenomenon exists

and, if necessary, implement corrective action prior to interconnecting the products.

9. Input power to the ac voltage configuration of this product must be provided by a

UL-listed or CSA-certified power source with a Class 2 or Limited Power Source

(LPS) output. Input power to the dc voltage configurations of this product must be

provided by a National Electric Code (NEC) or a Canadian Electric Code (CEC)

Class 2 circuit.

10. This product contains a coin cell lithium battery that is only to be replaced at the

factory. Caution: There is a danger of explosion if the battery is incorrectly

replaced. Replace only with the same type. Dispose of used batteries according to

the battery manufacturer’s instructions. Attention: Il y a danger d’explosion s’il y a

remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du

même type. Mettre au rebut les batteries usagées conformément aux instructions

du fabricant.

11. In addition, if the equipment is to be used with telecommunications circuits, take the

following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically

designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone

line has been disconnected at the network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm.

There may be a remote risk of electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

EMI Warnings

WARNING:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements

that no modifications will be made to the equipment unless the changes or

modifications are expressly approved by Paradyne Corporation.

WARNING:

To Users of Digital Apparatus in Canada:

This Class A digital apparatus meets all requirements of the Canadian

interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du

règlement sur le matérial brouilleur du Canada.

Government Requirements and Equipment Return

Certain governments require that instructions pertaining to CSU connection to the

telephone network be included in the installation and operation manual. Specific

instructions are listed in the following sections.

Page is loading ...

Paradyne 3165 Reference guide

Brand: Paradyne

Model: 3165

Category: Modems

Type: Reference guide

Download PDF

report

Paradyne 3165 Reference guide

Paradyne 3165 Reference guide

Related papers

Other documents