Paradyne 3165 DSU/CSU User manual
- Category
- Networking
- Type
- User manual
Paradyne 3165 DSU/CSU is a high-performance data service unit/channel service unit that provides reliable and secure data transmission over T1 networks. It offers a range of features and capabilities to meet the diverse needs of businesses and organizations. With its advanced framing and coding formats, the 3165 DSU/CSU ensures high-quality data transmission and minimizes errors. It supports both ESF and D4 framing formats, as well as AMI and B8ZS line coding formats, providing flexibility and compatibility with various network environments.
Paradyne 3165 DSU/CSU is a high-performance data service unit/channel service unit that provides reliable and secure data transmission over T1 networks. It offers a range of features and capabilities to meet the diverse needs of businesses and organizations. With its advanced framing and coding formats, the 3165 DSU/CSU ensures high-quality data transmission and minimizes errors. It supports both ESF and D4 framing formats, as well as AMI and B8ZS line coding formats, providing flexibility and compatibility with various network environments.
ACCULINK 3165 DSU/CSU
QUICK REFERENCE
Document No. 3165-A2-GL11-30
Copyright 1998 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be
copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated
into any human or computer language in any form or by any means, electronic,
mechanical, magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Paradyne Corporation, 8545 126th Avenue North, P.O.
Box 2826, Largo, Florida 33779-2826.
Paradyne Corporation makes no representation or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of merchantability or
fitness for a particular purpose. Further, Paradyne Corporation reserves the right to
revise this publication and to make changes from time to time in the contents hereof
without obligation of Paradyne Corporation to notify any person of such revision or
changes.
Changes and enhancements to the product and to the information herein will be
documented and issued as a new release to this manual.
Warranty, Sales, and Service Information
Contact your sales or service representative directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, or
training, use one of the following methods:
Via the Internet: Visit the Paradyne World Wide Web site at
http://www.paradyne.com
Via Telephone: Call our automated call system to receive current information via
fax or to speak with a company representative.
— Within the U.S.A., call 1-800-870-2221
— International, call 727-530-2340
Trademarks
All products and services mentioned herein are the trademarks, service marks,
registered trademarks or registered service marks of their respective owners.
TM
1
ACCULINK 3165 DSU/CSU
Quick Reference
Document Number 3165-A2-GL11-30
January 1998
Quick Start Procedure
The following procedure is for experienced DSU/CSU users who are familiar with the
3165 DSU/CSU installation process and have no special requirements for their
application. See the
ACCULINK 316x Data Service Unit/Channel Service Unit
Operator’s Guide
(Document No. 3160-A2-GB21) for more information.
1. Attach the power cord to the rear of the DSU/CSU and the other end to a grounded
115 Vac power outlet.
2. Attach the 3165 DSU/CSU network connection to the T1 network using the
appropriate cable. Attach the 3165 DSU/CSU to the customer premises equipment
via the port connector.
3. Power on the DSU/CSU to perform the power-up self-test.
4. If you intend to use front panel emulation, connect the cable from the PC to the
COM port on the rear panel of the DSU/CSU.
5. If you intend to manage the 3165 DSU/CSU with SNMP, cable either the COM or
MODEM port (as appropriate for your configuration). Then, configure the SNMP
management link.
6. The Factory 1 configuration for ESF framing format and B8ZS line coding format is
the default configuration and is appropriate for most networks. If this configuration
does not work for you, try the Factory 2 configuration for D4 framing format and
AMI line coding format. To further customize configuration options, refer to
Changing Configuration Options
in Chapter 3,
Operation
, and to Appendix C,
Configuration Options
,
in the
ACCULINK 316x Data Service Unit/Channel Service
Unit Operator’s Guide
.
7. During the power-up self-test, the FAIL LED flashes, then all LEDs blink twice.
When the test is complete, verify that the DSU/CSU is functional by observing that
the OK and NETWORK SIG LEDs are lit.
2
97-1557
8
PSTN
T1 Network
Modem
Power
Modem
Power
Front
Panel
3165 DSU/CSU
3165
DSU/CSU
3165
DSU/CSU
Serial
Port
or
COM Port
Network
Port
Modem
Port
COM
Port
Network
Port
Modem
Port
Network
Port
or
SNMP Manager
Workstation
SNMP Manager
Workstation
PC
or
CAUTION:
AUX PORT OR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK
AUX PORT
COM PORT MODEM
DTE
POWER
NETWORK
NEC
CLASS 2
INPUT
CAUTION:
AUX PORT OR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK
AUX PORT
COM PORT MODEM
DTE
POWER
NETWORK
NEC
CLASS 2
INPUT
Terminal
or
Terminal
T1 or Serial Connections
Dial Connections
Cabling Examples
3
Configuration Options
Configuration options are accessed from the Configuration branch of the front panel
menu.
DSU ESF
Stat
97-15579
DevHS
STest Perf TSt at LED ID
T1 PrtnPrtnUserTelco
Cur
24Tot
Intvl
FarNear
Cur
8Tot
Intvl
Test
Rlpbk Lpbk Ptrns Lamp
QRSS 511
Abort Mon
LLBUP
LLBDN
54UP
54DN
FT1UP
FT1DN
PLB DLB RLBLLBAbort DCLB DTLB
QRSS 1in8 511
Send
Cnfig Ctrl
Rel
ClrReg
Reset
CID
Passwd
DL
Call
DiscDial ChDir
1 . . 5,A
(Directory)
1 . . 5,A
(Directory)
User Prt1
FarNear
Load Edit Area From:
Choose Function:
Activ Cust1 Cust2 Fact1 Fact2
User AlarmNET Chan Gen Mgmt
Gen Trap
ClearDsply
Save
Cust1Activ Cust2
Edit
Port
4
Table 1. Port Configuration Options (1 of 2)
Option Factory 1 Factory 2 Comments/Description
E530 E530
Port Type:
V.35 V.35
Selects the
p
ort t
yp
e: EIA-530A,
Port Type:
RS449 RS449
S
e
l
ec
t
s
th
e por
t
t
ype:
EIA
-
530A
,
V.35, RS449, or X.21.
X.21 X.21
Base Rate:
Nx64 Nx64
Enables the
p
ort to either Nx56 or
Base Rate:
Nx56 Nx56
E
na
bl
es
th
e por
t
t
o e
ith
er
N
x
56
or
Nx64 rates.
Disab Disab
Net DCLB:
V.54 V.54
Network-initiated DCLB, allows
DCLB to be controlled by inband
Net DCLB:
FT1 FT1
,
DCLB to be controlled by inband
V.54 or FT1 (ANSI) codes.
Both Both
()
Disab Disab
Port LB:
DTLB DTLB
Port-initiated Loopbacks, allows
Loopbacks to be initiated through
Port LB:
DCLB DCLB
p,
Loopbacks to be initiated through
the port by the external DTE.
Both Both
epo by ee e a
Disab Disab
All Ones:
DTR DTR
All ones sent to network (DTE) T1
All Ones:
RTS RTS
All
ones
sent
to
network
(DTE)
T1
when DTR or RTS interrupted.
Both Both
Rcv Yellow:
None None
Data port remains enabled, or is
disabled on receiving Yellow on
Rcv
Yellow:
(Received Yellow)
Halt Halt
p,
disabled, on receiving Yellow on
network T1.
Tx Clock:
Int Int
Selects whether the transmitted
data clock is internal (TXC) or
Tx Clock:
Ext Ext
data clock is internal (TXC) or
external (XTXC).
InvertTxC:
Enab Enab
Selects
p
hase inversion of the
I
nver
tT
x
C
:
(Invert Tx Clock)
Disab Disab
S
e
l
ec
t
s p
h
ase
i
nvers
i
on o
f
th
e
transmit clock (TXC).
InvertData:
Enab Enab
Allows the data on the port to be
InvertData:
Disab Disab
Allows
the
data
on
the
port
to
be
inverted.
5
Table 1. Port Configuration Options (2 of 2)
Option Comments/DescriptionFactory 2Factory 1
10E–4 10E–4
10E–5 10E–5
Err Rate:
(Excessive Error
10E–6 10E–6
Selects the error rate threshold for
Excessive Error Rate Alarm
(Excessive Error
Rate)
10E–7 10E–7
Excessive Error Rate Alarm.
ae)
10E–8 10E–8
10E–9 10E–9
Table 2. Network Interface Configuration Options
Option Factory 1 Factory 2 Comments/Description
NET Framing:
D4 D4
Selects D4 or ESF framing format
NET Framing:
ESF ESF
Selects D4 or ESF framing format.
NET Coding:
AMI AMI
Selects AMI or B8ZS line coding
NET Coding:
B8ZS B8ZS
Selects
AMI
or
B8ZS
line
coding
format.
0.0 0.0
LBO:
–7.5 –7.5
Provides Line Build Out in dB
LBO:
–15 –15
Provides Line Build Out in dB.
–22.5 –22.5
ANSI PRM:
Enab Enab
Sends ANSI Performance Report
ANSI PRM:
Disab Disab
Sends
ANSI
Performance
Report
Messages.
Mgmt Link:
Disab Disab
Specifies whether the FDL’s
Mgmt Link:
SNMP SNMP
Specifies
whether
the
FDLs
Management Link is enabled.
NET LLB:
Enab Enab
Network-initiated LLB allows LLB to
NET LLB:
Disab Disab
Network-initiated
LLB
allows
LLB
to
be controlled by inband LLB codes.
NET PLB:
Enab Enab Network-initiated PLB allows PLB
to be controlled by FDL PLB
NET PLB:
Disab Disab
to be controlled by FDL PLB
messages.
62411 62411
Provides enforcement of ones
d it t ti AT&T TR
BitStuff:
Part68 Part68
Provides enforcement of ones
density protection per AT&T TR
62411
,
ANSI T1-403
,
and FCC
BitStuff:
Disab Disab
62411
,
ANSI
T1
-
403
, an
d
FCC
Part 68 Technical Publication.
Circuit Ident:
Edit Edit
Specifies the transmission vendor’s
Circuit
Ident:
Clear Clear
Specifies
the
transmission
vendor s
circuit identifier.
6
Table 3. Channel Configuration Options (1 of 2)
Option Factory 1 Factory 2 Comments/Description
Block Block
Determines how channels are
Assign By:
ACAMI ACAMI
Determines how channels are
assigned: contiguous blocks,
ACAMI i di id l h l
Assign By:
Chan Chan
assigned: contiguous blocks,
ACAMI or individual channels.
Option Factory 1 Factory 2 Comments/Description
Port Rate:
64 (56)
128 (112)
192 (168)
256 (224)
320 (280)
384 (336)
448 (392)
512 (448)
576 (504)
640 (560)
704 (616)
768 (672)
832 (728)
896 (784)
960 (840)
1024 (896)
1088 (952)
1152 (1008)
1216 (1064)
1280 (1120)
1344 (1176)
1408 (1232)
1472 (1288)
1536 (1344)
64 (56)
128 (112)
192 (168)
256 (224)
320 (280)
384 (336)
448 (392)
512 (448)
576 (504)
640 (560)
704 (616)
768 (672)
832 (728)
896 (784)
960 (840)
1024 (896)
1088 (952)
1152 (1008)
1216 (1064)
1280 (1120)
1344 (1176)
1408 (1232)
1472 (1288)
1536 (1344)
Selects the data rate for the port.
The possible rates depend on
whether the port is configured for
Nx56 or Nx64.
This configuration option only
appears if the “Assigned By”
configuration option is Block or
ACAMI.
7
Table 3. Channel Configuration Options (2 of 2)
Clear Clear
Clears (unassigns) channels for
this port.
Start At:
N1 (D1)
N2 (D2)
N3 (D3)
N4 (D4)
N5 (D5)
N6 (D6)
N7 (D7)
N8 (D8)
N9 (D9)
N10 (D10)
N11 (D11)
N12 (D12)
N13 (D13)
N14 (D14)
N15 (D15)
N16 (D16)
N17 (D17)
N18 (D18)
N19 (D19)
N20 (D20)
N21 (D21)
N22 (D22)
N23 (D23)
N24 (D24)
N1 (D1)
N2 (D2)
N3 (D3)
N4 (D4)
N5 (D5)
N6 (D6)
N7 (D7)
N8 (D8)
N9 (D9)
N10 (D10)
N11 (D11)
N12 (D12)
N13 (D13)
N14 (D14)
N15 (D15)
N16 (D16)
N17 (D17)
N18 (D18)
N19 (D19)
N20 (D20)
N21 (D21)
N22 (D22)
N23 (D23)
N24 (D24)
This configuration option appears if
the “Assigned By” configuration
option is Block or ACAMI.
Line 1 Displays: Line 2 Displays: Meaning Comments/Description
— Unassigned
N1 N2 N3 ...... N24:
Prt1
Channel assigned
to port 1
This configuration option appears if
the “Assigned By” configuration
option is individual channels
N1
N2
N3
......
N24:
(If assigned to NET)
D1 D2 D3 ..... D24:
(If assigned to DTE)
D1, D2 ... D24
Channel assigned
to this DTE
channel
gyg
option is individual channels
(Chan).
Function key under the channel
(N1 N2 t ) i ( i )
(If assigned to DTE)
N1, N2 ... N24
Channel assigned
to this NET
channel
Function
key
under
the
channel
(N1, N2 etc.) assigns (unassigns)
port (1, 2, 3, or 4) to that channel.
8
Table 4. General Configuration Options
Option Factory 1 Factory 2 Comments/Description
Gen Yellow:
Enab Enab
Yellow alarm is
g
enerated b
y
the
G
en
Y
e
ll
ow:
(Generate Yellow)
Disab Disab
Y
e
ll
ow a
l
arm
i
s genera
t
e
d
b
y
th
e
DSU/CSU on LOS, LOF, or AIS.
NET NET
DTE DTE
Selects the clock source to be
Clock Src:
Prt1 Prt1
Selects the clock source to be
used as the master clock for the
DSU/CSU
Clock Src:
Int Int
used as the master clock for the
DSU/CSU.
Ext Ext
2048 2048
Clock Rate:
1544 1544
Selects the clock rate of the source
if external.
Clock Rate:
8 8
if
ex
t
erna
l
.
Tst Timeout
Enab Enab
Specifies whether the durations of
user initiated tests are limited by
Tst Timeout
Disab Disab
p
user-initiated tests are limited by
Tst Duration.
10 10
Tst Duration
Up Up
Specifies the duration of
iii dl b k d
Tst Duration
Down Down
Specifies
the
duration
of
user-initiated loopback and pattern
tests.
Save Save
tests
.
9
Table 5. User Configuration Options (1 of 3)
Option Factory 1 Factory 2 Comments/Description
Self
-
Test:
Enab Enab
Allows bypass of self-test on
Self-Test:
Disab Disab
Allows
bypass
of
self
-
test
on
initialization.
FP Access:
Enab Enab
Controls whether front panel
FP Access:
Disab Disab
Controls
whether
front
panel
access or display is allowed.
FP Pass:
Enab Enab
Controls whether front panel
FP Pass:
Disab Disab
Controls
whether
front
panel
pass-through is allowed.
Dial
-
In:
Enab Enab
Controls whether dial-in access is
Dial-In:
Disab Disab
Controls
whether
dial-in
access
is
allowed.
None None
Password:
Com Com
Controls whether a password is
Password:
Modem Modem
Controls
whether
a
password
is
required during a call setup.
Both Both
Mgmt Mgmt
Com Use:
ASCII ASCII
Controls how the COM port is
Com Use:
Daisy Daisy
Controls
how
the
COM
port
is
used.
Term Term
Com Type:
Async Async
Controls whether the COM port is
Com Type:
Sync Sync
Controls
whether
the
COM
port
is
synchronous or asynchronous.
Com Clk:
Int Int
Controls whether the COM port
Com Clk:
Ext Ext
Controls
whether
the
COM
port
uses an internal or external clock.
1.2 1.2
2.4 2.4
Com Rate:
4.8 4.8
Com Rate:
(Communication Port
Rt)
9.6 9.6
Selects the bit rate for the COM
p
ort.
(Communication Port
Rate)
14.4 14.4
por
t
.
19.2 19.2
38.4 38.4
Char Length:
7 7
Selects the character length for the
Char Length:
8 8
Selects
the
character
length
for
the
COM port.
CParity:
None None
CParity:
(Communication Port
Parity)
Even Even
Selects the parity for the COM port.
(
Parity)
Odd Odd
py p
10
Table 5. User Configuration Options (2 of 3)
Option Comments/DescriptionFactory 2Factory 1
CStop Bits:
1 1
CStop Bits:
(Communication Port
St Bit )
1.5 1.5
Selects the number of stop bits for
the COM
p
ort.
(Communication Port
Stop Bits)
2 2
th
e
COM
por
t
.
Ignore DTR:
Yes Yes
S
p
ecifies whether the COM
p
ort
Ignore DTR:
No No
S
pec
ifi
es w
h
e
th
er
th
e
COM
por
t
ignores DTR.
CmInActTm:
(COM Port Inactivity
Enab Enab
Specifies whether the
communication port disconnects
(COM Port Inactivity
Timeout)
Disab Disab
p
communication port disconnects
after a certain period of inactivity.
5 5
CmDiscTm:
(
COM Port
Up Up
Specifies the period of inactivity
(
1 to 60 minutes
)
that causes a
(COM
P
or
t
Disconnect Time)
Down Down
(1
t
o
60
m
i
nu
t
es
)
th
a
t
causes a
disconnect if CmInActTm is
enabled.
Save Save
ena
bl
e
d
.
Mgmt Mgmt
Modem Use:
ASCII ASCII
Controls whether the MODEM port
is used for SNMP mana
g
ement.
Term Term
i
s use
d
f
or
SNMP
managemen
t
.
Modem Type:
Async Async
Controls whether the MODEM port
Modem Type:
Sync Sync
Controls
whether
the
MODEM
port
is synchronous or asynchronous.
Modem Rate:
1.2 1.2
Selects the bit rate for the MODEM
Modem Rate:
2.4 2.4
Selects
the
bit
rate
for
the
MODEM
port.
MChar Len:
(Modem Port
7 7
Selects the character len
g
th for the
(Modem Port
Character Length)
8 8
S
e
l
ec
t
s
th
e c
h
arac
t
er
l
eng
th
f
or
th
e
MODEM port.
None None
MParity:
(
Modem Port Parit
y)
Even Even
Selects the parity for the MODEM
p
ort.
(M
o
d
em
P
or
t
P
ar
it
y
)
Odd Odd
por
t
.
MStop Bits:
(Modem Port Stop
1 1
Selects the number of stop bits for
(Modem Port Stop
Bits)
2 2
Selects
the
number
of
stop
bits
for
the MODEM port.
LSpaceDsc:
(Long Space
Enab Enab
Selects the long space disconnect
configuration optionfor terminating
p
(Long Space
Disconnect)
Disab Disab
gp
configuration option for terminating
modem connections.
MoInActTm:
(Modem Port
Enab Enab
Specifies whether the modem port
disconnects after a certain period
(Modem Port
Inactivity Timeout)
Disab Disab
pp
disconnects after a certain period
of inactivity.
11
Table 5. User Configuration Options (3 of 3)
Option Comments/DescriptionFactory 2Factory 1
5 5
MoDiscTm:
(
Modem Port
Up Up
Specifies the period of inactivity
(1 t 60 i t ) th t
(M
o
d
em
P
or
t
Disconnect Time)
Down Down
Specifies the period of inactivity
(1 to 60 minutes) that causes a
disconnect if MInActTm is enabled.
Save Save
d sco ec c s e ab ed
TnSession:
Enab Enab
Specifies whether the DSU/CSU
responds to Telnet session
T
n
S
ess
i
on:
(Telnet Session)
Disab Disab
p
responds to Telnet session
requests.
TnPaswd:
Enab Enab
S
p
ecifies whether a
p
assword is
T
n
P
asw
d
:
(Telnet Password)
Disab Disab
S
pec
ifi
es w
h
e
th
er a passwor
d
i
s
required for Telnet sessions.
TnInActTm:
(Telnet Inactivity
Enab Enab
Specifies whether a Telnet session
disconnects after a certain period
(Telnet Inactivity
Timeout)
Disab Disab
p
disconnects after a certain period
of inactivity.
5 5
TnDiscTm:
(
Telnet Disconnect
Up Up
The period of inactivity (1 to
60 minutes
)
that causes a
(T
e
l
ne
t
Di
sconnec
t
Time)
Down Down
60
m
i
nu
t
es
)
th
a
t
causes a
disconnect if TnInActTm is
enabled.
Save Save
ena
bl
e
d
.
12
Table 6. Alarm Configuration Options
Option Factory 1 Factory 2 Comments/Description
Disab Disab Does not display alarm messages.
Al M
Modem Modem
Sends alarm messages to Modem
port.
Alrm Msg:
Com Com
Sends alarm messages to COM
port.
Both Both
Sends alarm messages to both
ports.
SNMP Trap:
Enab Enab
Sends SNMP traps
SNMP Trap:
Disab Disab
Sends SNMP traps.
TrapDisc:
Enab Enab
Specifies whether the modem
connection will disconnect after a
TrapDisc:
Disab Disab
p
connection will disconnect after a
trap is sent.
DialOut:
Enab Enab
Provides the option to allow
automatic dial out to send alarm
DialOut:
Disab Disab
p
automatic dial-out to send alarm
messages on MODEM port.
Call Retry:
Enab Enab
Specifies whether an outgoing call
is retried on a busy or failed call
Call Retry:
Disab Disab
pgg
is retried on a busy or failed call
attempt.
Dial Delay:
1–4
5
6–10
1–4
5
6–10
The time (in minutes) to delay
between successive alarm
dial-outs or retry attempts.
AltDialDir:
None
1–5
None
1–5
The alternate dial-out directory to
use if a call to the primary number
cannot be completed.
10E–4 10E–4
10E–5 10E–5
Err Rate:
(Excessive Error
10E–6 10E–6 The error rate threshold for
Excessive Error Rate Alarm
(Excessive Error
Rate)
10E–7 10E–7
Excessive Error Rate Alarm.
Rate)
10E–8 10E–8
10E–9 10E–9
13
Table 7. Management – General Configuration Options (1 of 2)
Option Factory 1 Factory 2 Comments/Description
SNMP Mgt:
Disab Disab
Specifies whether the DSU/CSU
responds to SNMP session
SNMP Mgt:
Enab Enab
p
responds to SNMP session
requests.
NMS Valid:
Disab Disab
Specifies whether the DSU/CSU
validates the IP address of an
NMS Valid:
Enab Enab
validates
the
IP
address
of
an
SNMP manager attempting
access.
Num Sec Mgrs:
1
2–10
1
2–10
The number of management
systems authorized to send SNMP
messages to this unit.
NMS
n
IP Adr:
Edit Edit
Specifies the IP address for each
NMS This configuration option is
NMS
n
IP Adr:
Clear Clear
p
NMS. This configuration option is
repeated for all
n
NMSs.
NMS
n
ACS:
Read Read
The type of access allowed for
NMS
n
ACS:
R/W R/W
The
type
of
access
allowed
for
NMS
n
.
System Name:
Edit Edit
The SNMP system name for this
System Name:
Clear Clear
The
SNMP
system
name
for
this
device.
System Location:
Edit Edit
The SNMP system location for this
System Location:
Clear Clear
The
SNMP
system
location
for
this
device.
System Contact:
Edit Edit
The SNMP system contact name
System Contact:
Clear Clear
The
SNMP
system
contact
name
for this device.
CommunityName1:
Edit Edit
A community name that is allowed
access to this device Defaults to
CommunityName1:
Clear Clear
y
access to this device. Defaults to
public
.
Access 1:
Read Read
The type of access allowed for
Access 1:
R/W R/W
The
type
of
access
allowed
for
community name 1.
CommunityName2:
Edit Edit
A community name that is allowed
CommunityName2:
Clear Clear
A
community
name
that
is
allowed
access to this device.
Access 2:
Read Read
The type of access allowed for
Access 2:
R/W R/W
The
type
of
access
allowed
for
community name 2.
IP Adr:
Edit Edit
The IP address needed to access
IP Adr:
Clear Clear
The
IP
address
needed
to
access
the device.
NetMask:
Edit Edit
The Subnet Mask needed to
NetMask:
Clear Clear
The
Subnet
Mask
needed
to
access the device.
Com IP Adr:
Edit Edit
The IP address for the COM port
Com IP Adr:
Clear Clear
The
IP
address
for
the
COM
port
when configured for SNMP.
14
Table 7. Management – General Configuration Options (2 of 2)
Option Comments/DescriptionFactory 2Factory 1
Com NetMask:
Edit Edit
The Subnet Mask needed to
access the device when the COM
Com NetMask:
Clear Clear
access the device when the COM
port is configured for SNMP.
Com Link:
PPP PPP
The link layer protocol for the COM
Com Link:
SLIP SLIP
The
link
layer
protocol
for
the
COM
port when configured for SNMP.
Modem IP Adr:
Edit Edit
Specifies the IP address for the
MODEM port when configured for
Modem IP Adr:
Clear Clear
p
MODEM port when configured for
SNMP.
Mdm NetMask:
Edit Edit
Specifies the Subnet Mask needed
to access the device when the
Mdm NetMask:
Clear Clear
to
access
the
device
when
the
MODEM port is configured for
SNMP.
Alt Mdm IP Adr:
Edit Edit
Specifies the alternate IP address
for the MODEM port when
Alt Mdm IP Adr:
Clear Clear
p
for the MODEM port when
configured for SNMP.
Alt Mdm NetMask:
Edit Edit
Specifies the alternate modem
Subnet Mask needed to access the
Alt Mdm NetMask:
Clear Clear
Subnet
Mask
needed
to
access
the
device when the MODEM port is
configured for SNMP.
Modem Link:
PPP PPP Specifies the link layer protocol for
the MODEM port when configured
Modem Link:
SLIP SLIP
pyp
the MODEM port when configured
for SNMP.
None None
Def Netwk:
Com Com
S
p
ecifies the default network
Def Netwk:
Modem Modem
S
pec
ifi
es
th
e
d
e
f
au
lt
ne
t
wor
k
destination.
FDL FDL
15
Table 8. Management – Trap Configuration Options
Option Factory 1 Factory 2 Comments/Description
Num Trap Mgrs:
1
2–6
1
2–6
The number of trap managers
supported by the device.
Trap
n
IP Adr:
Edit Edit
Specifies the IP address for each
trap manager. This configuration
Trap
n
IP Adr:
Clear Clear
trap
manager
.
This
configuration
option is repeated for all
n
managers.
None None
Def Def
Trap
n
Dst:
Com Com
Specifies the network destination
for Tra
p
Mana
g
er
n
.
Modem Modem
f
or
T
rap
M
anager
n
.
FDL FDL
Disab Disab
Gen Trap:
Warm Warm Specifies the general trap types to
enable: WarmStart Authentication
Gen Trap:
Auth Auth
pgpyp
enable: WarmStart, Authentication
Failure or both.
Both Both
Failure
or
both
.
Entp Trap:
Enab Enab
Specifies whether the
EnterpriseSpecific trap type is
Entp Trap:
Disab Disab
p
EnterpriseSpecific trap type is
enabled.
Disab Disab
Link Trap:
Up Up Specifies the link trap type to
enable: Trap on Link Up Link
Link Trap:
Down Down
ppyp
enable: Trap on Link Up, Link
Down, or both.
Both Both
Down
,
or
both
.
NET NET
T1s T1s When any link trap types are
enabled specifies which links to
Trap I/F:
Ports Ports
ypyp
enabled, specifies which links to
send traps for.
All All
send
traps
for
.
16
Notes
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Paradyne 3165 DSU/CSU User manual
- Category
- Networking
- Type
- User manual
Paradyne 3165 DSU/CSU is a high-performance data service unit/channel service unit that provides reliable and secure data transmission over T1 networks. It offers a range of features and capabilities to meet the diverse needs of businesses and organizations. With its advanced framing and coding formats, the 3165 DSU/CSU ensures high-quality data transmission and minimizes errors. It supports both ESF and D4 framing formats, as well as AMI and B8ZS line coding formats, providing flexibility and compatibility with various network environments.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Paradyne 3165 Reference guide
-
Paradyne ACCULINK 3150 Reference guide
-
Paradyne ACCULINK 3161 User manual
-
Paradyne 3160-A2-GB21-50 User manual
-
Paradyne ACCULINK 3150 Reference guide
-
Paradyne 3160-A3 User manual
-
Paradyne ACCULINK 3161 Reference guide
-
Paradyne ACCULINK 3164 User manual
-
Paradyne ACCULINK 3164-A2 DSU User manual
-
Paradyne ACCULINK 3151 CSU Quick Reference Manual
Other documents
-
ADTRAN DSU II (TST) User manual
-
AT&T 3551 User manual
-
Blaupunkt B10RD Datasheet
-
-
Blaupunkt BT 10 Operating instructions
-
-
Patton electronic 2720 T1 User manual
-
Meyer Sound MDM Operating instructions
-
ESCO Technologies 3165-01 User manual
-
Kensington 62411 User manual
