Paradyne ACCULINK 3163 DSU Reference guide

Brand: Paradyne

Model: ACCULINK 3163 DSU

Category: Modems

Type: Reference guide

This manual is also suitable for

ACCULINK 3163 DSU/CSU

QUICK REFERENCE

Document No. 3163-A2-GL10-00

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be

copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated

into any human or computer language in any form or by any means, electronic,

mechanical, magnetic, manual or otherwise, or disclosed to third parties without the

express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo,

FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the

contents hereof and specifically disclaims any implied warranties of merchantability or

fitness for a particular purpose. Further, Paradyne Corporation reserves the right to

revise this publication and to make changes from time to time in the contents hereof

without obligation of Paradyne Corporation to notify any person of such revision or

changes.

Changes and enhancements to the product and to the information herein will be

documented and issued as a new release to this manual.

Warranty, Sales, and Service Information

Contact your local sales representative, service representative, or distributor directly for

any help needed. For additional information concerning warranty, sales, service, repair,

installation, documentation, training, distributor locations, or Paradyne worldwide office

locations, use one of the following methods:

 Via the Internet: Visit the Paradyne World Wide Web site at

http://www.paradyne.com

 Via Telephone: Call our automated call system to receive current information via

fax or to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A, call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them

to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,

or send e-mail to [email protected]. Include the number and title of this

document in your correspondence. Please include your name and phone number if you

are willing to provide additional clarification.

Trademarks

All products and services mentioned herein are the trademarks, service marks,

registered trademarks or registered service marks of their respective owners.

ACCULINK 3163 DSU/CSU

Quick Reference

Document Number 3163-A2-GL10-00

December 1998

Product Documentation on the World Wide Web

We provide complete product documentation online. This lets you search the

documentation for specific topics and print only what you need, reducing the waste of

surplus printing. It also helps us maintain competitive prices for our products.

Complete documentation for this product is available at www.paradyne.com. Select

Service & Support

→

Technical Manuals

→

T1/E1 Digital Access Devices.

Select the following document:

Document No. 3163-A2-GB20

ACCULINK 3163 Data Service Unit/Channel Service Unit User’s Guide

To request a paper copy of a Paradyne document:

 Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

 Outside the U.S.A., call 1-727-530-8623

Before installing the DSU/CSU, read the

Important Safety Instructions

beginning on

page 13.

Quick Start Procedure

The following procedure is for experienced DSU/CSU users who are familiar with the

3163 DSU/CSU installation process and have no special requirements for their

application. See the

ACCULINK 3163 Data Service Unit/Channel Service Unit User’s

Guide

for more information.

1. If ac power is to be used, attach the power cord to the rear of the DSU/CSU and

the power transformer to a grounded 100 Vac power outlet. For information about

the optional dc power cable for a +24 Vdc or –48 Vdc power source, see the User’s

Guide.

2. Attach the 3163 DSU/CSU network connection to the T1 network using the

appropriate cable. Attach the 3163 DSU/CSU to the customer premises equipment

via the port connector.

3. Power on the DSU/CSU to perform the power-up self-test.

4. If you intend to use front panel emulation, connect the cable from the PC to the

COM port on the rear panel of the DSU/CSU.

5. The Factory 1 configuration for ESF framing format and B8ZS line coding format is

the default configuration and is appropriate for most networks. If this configuration

does not work for you, try the Factory 2 configuration for D4 framing format and

AMI line coding format. To further customize configuration options, refer to the

configuration option tables beginning on page 4.

6. During the power-up self-test, the FAIL LED flashes, then all LEDs blink twice.

When the test is complete, verify that the DSU/CSU is functional by observing that

the OK and NETWORK SIG LEDs are lit.

PORT 1

COM PORT MODEM

POWER

NETWORK

CAUTION:

AUX PORT OR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK

NEC

PORT 1

COM PORT MODEM

POWER

NETWORK

CAUTION:

AUX PORT OR COM PORT MUST NOT BE CONNECTED TO PSTN OR T1 NETWORK

NEC

98-15941a

PSTN

Modem

Power

Modem

Power

Front

Panel

3163 DSU/CSU

3163

DSU/CSU

3163

DSU/CSU

Serial

Port

COM

Port

Network

Port

Modem

Port

COM

Port

Network

Port

Modem

Port

Network

Port

T1 or Serial Connections

Dial Connections

Terminal

T1 Network

Cabling Examples

Configuration Options

Configuration options are accessed from the Configuration branch of the front panel

menu.

DSU ESF

98-15943a

Stat

DevHS

STest Perf TStat LED ID

T1 PrtnPrtnUserTelco

Cur 24Tot Intvl

FarNear

Cur 8Tot Intvl

Load Edit Area From:

Choose Function:

Activ Cust1 Cust2 Fact1 Fact2

User AlarmNETPort Chan Gen Mgmt

Gen

Save

Cust1Activ Cust2

Edit

Cnfig

Prt1ClearDsply

Ctrl

Rel

ClrReg

Reset

CID

Passwd

DLCall

DiscDialPass ChDir

1 . . 5,A

(Directory)

1 . . 5,A

(Directory)

User Prt1

Test

Rlpbk Lpbk Ptrns Lamp

QRSS 511

Abort Mon

LLBUP

LLBDN

54UP

54DN

FT1UP

FT1DN

PLB

RLB

LLB

Abort

DCLB

DTLB

QRSS1in8 511

Send

Factory default configuration options are shown in boldface type in the following tables.

Table 1. Port Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

E530 E530

Port Type:

V.35 V.35

Selects the port t

pe: EIA-530A

Port Type:

RS449 RS449

Selects

the

ort

ty e:

EIA

530A

V.35, RS449, or X.21.

X.21 X.21

Base Rate:

Nx64 Nx64

Enables the port to either Nx56 or

Base Rate:

Nx56 Nx56

Enables

the

ort

either

Nx56

Nx64 rates.

Disab Disab

Net DCLB:

V.54 V.54

Network-initiated DCLB, allows

DCLB t b t ll d b i b d

Net DCLB:

FT1 FT1

DCLB to be controlled by inband

V.54 or FT1 (ANSI) codes.

Both Both

Disab Disab

Port LB:

DTLB DTLB

Port-initiated Loopbacks, allows

L b k t b i iti t d th h

Port LB:

DCLB DCLB

Loopbacks to be initiated through

the port by the external DTE.

Both Both

Disab Disab

All Ones:

DTR DTR

All ones sent to network

(

DTE

)

All Ones:

RTS RTS

All

ones

sent

network

(DTE)

when DTR or RTS interrupted.

Both Both

Rcv Yellow:

None None

Data port remains enabled, or is

di bl d i i Y ll

Rcv

Yellow:

(Received Yellow)

Halt Halt

disabled, on receiving Yellow on

network T1.

Tx Clock:

Int Int

Selects whether the transmitted

d t l k i i t l (TXC)

Tx Clock:

Ext Ext

data clock is internal (TXC) or

external (XTXC).

InvertTxC:

Enab Enab

Selects phase inversion of the

InvertTxC:

(Invert Tx Clock)

Disab Disab

Selects

hase

inversion

the

transmit clock (TXC).

InvertData:

Enab Enab

Allows the data on the port to be

InvertData:

Disab Disab

Allows

the

data

the

ort

inverted.

Table 2. Network Interface Configuration Options

Option Factory 1 Factory 2 Comments/Description

NET Framing:

D4 D4

Selects D4 or ESF framing format

NET Framing:

ESF ESF

Selects D4 or ESF framing format.

NET Coding:

AMI AMI

Selects AMI or B8ZS line coding

NET Coding:

B8ZS B8ZS

Selects

AMI

B8ZS

line

coding

format.

0.0 0.0

LBO:

–7.5 –7.5

Provides Line Build Out in dB

LBO:

–15 –15

Provides Line Build Out in dB.

–22.5 –22.5

ANSI PRM:

Enab Enab

Sends ANSI Performance Report

ANSI PRM:

Disab Disab

Sends

ANSI

Performance

Re ort

Messages.

Mgmt Link:

Disab Disab

Specifies whether the FDL’s

Mgmt Link:

SNMP SNMP

S ecifies

whether

the

FDLs

Management Link is enabled.

NET LLB:

Enab Enab

Network-initiated LLB allows LLB to

NET LLB:

Disab Disab

Network initiated

LLB

allows

LLB

be controlled by inband LLB codes.

NET PLB:

Enab Enab Network-initiated PLB allows PLB

to be controlled by FDL PLB

NET PLB:

Disab Disab

to be controlled by FDL PLB

messages.

62411 62411

Provides enforcement of ones

d i i AT&T TR

BitStuff:

Part68 Part68

density protection per AT&T TR

62411, ANSI T1

403, and FCC

Disab Disab

62411

ANSI

403

, an

FCC

Part 68 Technical Publication.

Circuit Ident:

Edit Edit

Specifies the transmission vendor’s

Circuit

Ident:

Clear Clear

S ecifies

the

transmission

vendor s

circuit identifier.

Table 3. Channel Configuration Options (1 of 2)

Option Factory 1 Factory 2 Comments/Description

Block Block

Determines how channels are

Assign By:

ACAMI ACAMI

Determines how channels are

assigned: contiguous blocks,

Chan Chan

gg ,

ACAMI or individual channels.

Port Rate:

64 (56)

128 (112)

192 (168)

256 (224)

320 (280)

384 (336)

448 (392)

512 (448)

576 (504)

640 (560)

704 (616)

768 (672)

832 (728)

896 (784)

960 (840)

1024 (896)

1088 (952)

1152 (1008)

1216 (1064)

1280 (1120)

1344 (1176)

1408 (1232)

1472 (1288)

1536 (1344)

64 (56)

128 (112)

192 (168)

256 (224)

320 (280)

384 (336)

448 (392)

512 (448)

576 (504)

640 (560)

704 (616)

768 (672)

832 (728)

896 (784)

960 (840)

1024 (896)

1088 (952)

1152 (1008)

1216 (1064)

1280 (1120)

1344 (1176)

1408 (1232)

1472 (1288)

1536 (1344)

Selects the data rate for the port.

The possible rates depend on

whether the port is configured for

Nx56 or Nx64.

This configuration option only

appears if the “Assigned By”

configuration option is Block or

ACAMI.

Table 3. Channel Configuration Options (2 of 2)

Option Factory 1 Factory 2 Comments/Description

Clear Clear

Clears (unassigns) channels for

this port.

Start At:

N1 (D1)

N2 (D2)

N3 (D3)

N4 (D4)

N5 (D5)

N6 (D6)

N7 (D7)

N8 (D8)

N9 (D9)

N10 (D10)

N11 (D11)

N12 (D12)

N13 (D13)

N14 (D14)

N15 (D15)

N16 (D16)

N17 (D17)

N18 (D18)

N19 (D19)

N20 (D20)

N21 (D21)

N22 (D22)

N23 (D23)

N24 (D24)

N1 (D1)

N2 (D2)

N3 (D3)

N4 (D4)

N5 (D5)

N6 (D6)

N7 (D7)

N8 (D8)

N9 (D9)

N10 (D10)

N11 (D11)

N12 (D12)

N13 (D13)

N14 (D14)

N15 (D15)

N16 (D16)

N17 (D17)

N18 (D18)

N19 (D19)

N20 (D20)

N21 (D21)

N22 (D22)

N23 (D23)

N24 (D24)

This configuration option appears if

the “Assigned By” configuration

option is Block or ACAMI.

Line 1 Displays: Line 2 Displays: Meaning Comments/Description

— Unassigned

N1 N2 N3 ...... N24:

Prt1

Channel assigned

to port 1

This configuration option appears if

the “Assigned By” configuration

option is individual channels

......

N24:

(If assigned to NET)

D1 D2 D3 ..... D24:

(If assigned to DTE)

D1, D2 ... D24

Channel assigned

to this DTE

channel

option is individual channels

(Chan).

Function key under the channel

(If

ass

gne

DTE)

N1, N2 ... N24

Channel assigned

to this NET

channel

Function

key

under

the

channel

(N1, N2 etc.) assigns (unassigns)

port (1, 2, 3, or 4) to that channel.

Table 4. General Configuration Options

Option Factory 1 Factory 2 Comments/Description

NET NET

Clock Src:

DTE DTE Selects the clock source to be

dth tlkfth

Clock Src:

Prt1 Prt1

used as the master clock for the

DSU/CSU.

Int Int

SU/CSU

Tst Timeout

Enab Enab

Specifies whether the durations of

i iti t d t t li it d b

Tst Timeout

Disab Disab

user-initiated tests are limited by

Tst Duration.

10 10

Tst Duration

Up Up

Specifies the duration of

iii dl b k d

ura

Down Down

user-initiated loopback and pattern

tests.

Save Save

Table 5. User Configuration Options (1 of 3)

Option Factory 1 Factory 2 Comments/Description

Self Test:

Enab Enab

Allows b

pass of self-test on

Self-Test:

Disab Disab

Allows

by ass

self-test

initialization.

FP Access:

Enab Enab

Controls whether front panel

FP Access:

Disab Disab

Controls

whether

front

anel

access or display is allowed.

FP Pass:

Enab Enab

Controls whether front panel

FP Pass:

Disab Disab

Controls

whether

front

anel

pass-through is allowed.

Dial In:

Enab Enab

Controls whether dial-in access is

Dial-In:

Disab Disab

Controls

whether

dial-in

access

allowed.

None None

Password:

Com Com

Controls whether a password is

Password:

Modem Modem

Controls

whether

assword

required during a call setup.

Both Both

Mgmt Mgmt

Com Use:

ASCII ASCII

Controls how the COM port is

used.

Term Term

used

Com Ty

Async Async

Controls whether the COM port is

Com Type:

Sync Sync

Controls

whether

the

COM

ort

synchronous or asynchronous.

Table 5. User Configuration Options (2 of 3)

Option Comments/DescriptionFactory 2Factory 1

Com Clk:

Int Int

Controls whether the COM port

Com Clk:

Ext Ext

Controls

whether

the

COM

ort

uses an internal or external clock.

1.2 1.2

2.4 2.4

Com Rate:

4.8 4.8

Com Rate:

(Communication Port

9.6 9.6

Selects the bit rate for the COM

ort.

(

Rate)

14.4 14.4

port

19.2 19.2

38.4 38.4

Char Length:

7 7

Selects the character len

th for the

Char Length:

8 8

Selects

the

character

length

for

the

COM port.

CParity:

None None

CParity:

(Communication Port

Pit)

Even Even

Selects the parity for the COM port.

(

Parity)

Odd Odd

CSto

Bits:

1 1

CStop Bits:

(Communication Port

1.5 1.5

Selects the number of stop bits for

the COM

ort.

(

Stop Bits)

2 2

the

COM

port

Ignore DTR:

Yes Yes

Specifies whether the COM port

Ignore DTR:

No No

S ecifies

whether

the

COM

ort

ignores DTR.

CmInActTm:

(COM P t I ti it

Enab Enab

Specifies whether the

i ti t di t

(COM Port Inactivity

Timeout)

Disab Disab

communication port disconnects

after a certain period of inactivity.

5 5

CmDiscTm:

(COM Port

Up Up

Specifies the period of inactivity

(1 to 60 minutes) that causes a

(COM

Port

Disconnect Time)

Down Down

minutes)

that

causes

disconnect if CmInActTm is

enabled.

Save Save

enabled

Mgmt Mgmt

Modem Use:

ASCII ASCII

Controls whether the MODEM port

is used for management.

Term Term

used

for

management

Modem Ty

Async Async

Controls whether the MODEM port

Modem Type:

Sync Sync

Controls

whether

the

MODEM

ort

is synchronous or asynchronous.

Table 5. User Configuration Options (3 of 3)

Option Comments/DescriptionFactory 2Factory 1

Modem Rate:

1.2 1.2

Selects the bit rate for the MODEM

Modem Rate:

2.4 2.4

Selects

the

bit

rate

for

the

MODEM

port.

MChar Len:

(Modem Port

7 7

Selects the character len

th for the

(Modem Port

Character Length)

8 8

Selects

the

character

length

for

the

MODEM port.

None None

MParity:

(Modem Port Parity)

Even Even

Selects the parity for the MODEM

ort.

(Modem

Port

Parity)

Odd Odd

port

MStop Bits:

(Modem Port Sto

1 1

Selects the number of stop bits for

(Modem Port Stop

Bits)

2 2

Selects

the

number

sto

bits

for

the MODEM port.

LSpaceDsc:

(L S

Enab Enab

Selects the long space disconnect

fi ti ti f t i ti

(Long Space

Disconnect)

Disab Disab

configuration option for terminating

modem connections.

MoInActTm:

(M d P t

Enab Enab

Specifies whether the modem port

di t ft t i i d

(Modem Port

Inactivity Timeout)

Disab Disab

disconnects after a certain period

of inactivity.

5 5

MoDiscTm:

(Modem Port

Up Up

Specifies the period of inactivity

(1 60 i ) h

(Modem

Port

Disconnect Time)

Down Down

(1 to 60 minutes) that causes a

disconnect if MInActTm is enabled.

Save Save

TnSession:

Enab Enab

Specifies whether the DSU/CSU

dtTl t i

TnSession:

(Telnet Session)

Disab Disab

responds to Telnet session

requests.

TnPaswd:

Enab Enab

Specifies whether a password is

TnPaswd:

(Telnet Password)

Disab Disab

S ecifies

whether

assword

required for Telnet sessions.

TnInActTm:

(T l t I ti it

Enab Enab

Specifies whether a Telnet session

di t ft t i i d

(Telnet Inactivity

Timeout)

Disab Disab

disconnects after a certain period

of inactivity.

5 5

TnDiscTm:

(Telnet Disconnect

Up Up

The period of inactivity (1 to

60 minutes) that causes a

(Telnet

Disconnect

Time)

Down Down

minutes)

that

causes

disconnect if TnInActTm is

enabled.

Save Save

enabled

Table 6. Alarm Configuration Options

Option Factory 1 Factory 2 Comments/Description

Disab Disab Does not display alarm messages.

Modem Modem

Sends alarm messages to Modem

port.

Alrm Msg:

Com Com

Sends alarm messages to COM

port.

Both Both

Sends alarm messages to both

ports.

DialOut:

Enab Enab

Provides the option to allow

ttidiltt dl

DialOut:

Disab Disab

automatic dial-out to send alarm

messages on MODEM port.

Call Retry:

Enab Enab

Specifies whether an outgoing call

i t i d b f il d ll

Call Retry:

Disab Disab

is retried on a busy or failed call

attempt.

Dial Delay:

1–4

6–10

1–4

6–10

The time (in minutes) to delay

between successive alarm

dial-outs or retry attempts.

AltDialDir:

None

1–5

None

1–5

The alternate dial-out directory to

use if a call to the primary number

cannot be completed.

10E–4 10E–4

10E–5 10E–5

Err Rate:

(E i E

10E–6 10E–6 The error rate threshold for

EiERtAl

(Excessive Error

Rate)

10E–7 10E–7

Excessive Error Rate Alarm.

ae)

10E–8 10E–8

10E–9 10E–9

Table 7. Management Configuration Options

Option Factory 1 Factory 2 Comments/Description

IP Adr:

Edit Edit

The IP address needed to access

IP Adr:

Clear Clear

The

address

needed

access

the device.

NetMask:

Edit Edit

The Subnet Mask needed to

NetMask:

Clear Clear

The

Subnet

Mask

needed

access the device.

Com IP Adr:

Edit Edit

The IP address for the COM port

Com IP Adr:

Clear Clear

The

address

for

the

COM

ort

when configured for Mgmt.

Com NetMask:

Edit Edit

The Subnet Mask needed to

th d i h th COM

Com NetMask:

Clear Clear

access the device when the COM

port is configured for Mgmt.

Com Link:

PPP PPP

The link la

er protocol for the COM

Com Link:

SLIP SLIP

The

link

layer

rotocol

for

the

COM

port when configured for Mgmt.

Modem IP Adr:

Edit Edit

Specifies the IP address for the

MODEM t h fi d f

Modem IP Adr:

Clear Clear

MODEM port when configured for

Mgmt.

Mdm NetMask:

Edit Edit

Specifies the Subnet Mask needed

to access the device when the

Mdm NetMask:

Clear Clear

access

the

device

when

the

MODEM port is configured for

Mgmt.

Alt Mdm IP Adr:

Edit Edit

Specifies the alternate IP address

f th MODEM t h

Alt Mdm IP Adr:

Clear Clear

for the MODEM port when

configured for Mgmt.

Alt Mdm NetMask:

Edit Edit

Specifies the alternate modem

Subnet Mask needed to access the

Alt Mdm NetMask:

Clear Clear

Subnet

Mask

needed

access

the

device when the MODEM port is

configured for Mgmt.

Modem Link:

PPP PPP Specifies the link layer protocol for

th MODEM t h fi d

Modem Link:

SLIP SLIP

the MODEM port when configured

for Mgmt.

None None

Def Netwk:

Com Com

Specifies the default network

Def Netwk:

Modem Modem

S ecifies

the

default

network

destination.

FDL FDL

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or included in the

manual.

2. When an ac power source is used, this product is intended to be used with a 3-wire grounding

type plug – a plug which has a grounding pin. This is a safety feature. Equipment grounding is

vital to ensure safe operation. Do not defeat the purpose of the grounding type plug by

modifying the plug or using an adapter.

Prior to installation, use an outlet tester or a voltmeter to check the ac receptacle for the

presence of earth ground. If the receptacle is not properly grounded, the installation must not

continue until a qualified electrician has corrected the problem.

If a 3-wire grounding type power source is not available, consult a qualified electrician to

determine another method of grounding the equipment.

3. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of

the product and to protect it from overheating, these slots and openings must not be blocked or

covered.

4. Do not allow anything to rest on the power cord and do not locate the product where persons

will walk on the power cord.

5. Do not attempt to service this product yourself, as opening or removing covers may expose

you to dangerous high voltage points or other risks. Refer all servicing to qualified service

personnel.

6. General purpose cables are provided with this product. Special cables, which may be required

by the regulatory inspection authority for the installation site, are the responsibility of the

customer.

7. When installed in the final configuration, the product must comply with the applicable Safety

Standards and regulatory requirements of the country in which it is installed. If necessary,

consult with the appropriate regulatory agencies and inspection authorities to ensure

compliance.

8. A rare phenomenon can create a voltage potential between the earth grounds of two or more

buildings. If products installed in separate buildings are interconnected, the voltage potential

may cause a hazardous condition. Consult a qualified electrical consultant to determine

whether or not this phenomenon exists and, if necessary, implement corrective action prior to

interconnecting the products.

9. Input power to the ac voltage configuration of this product must be provided by a UL-listed or

CSA-certified power source with a Class 2 or Limited Power Source (LPS) output. Input power

to the dc voltage configurations of this product must be provided by a National Electric Code

(NEC) or a Canadian Electric Code (CEC) Class 2 circuit.

10. This product contains a coin cell lithium battery that is only to be replaced at the factory.

Caution: There is a danger of explosion if the battery is incorrectly replaced. Replace only with

the same type. Dispose of used batteries according to the battery manufacturer’s instructions.

Attention: Il y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer

uniquement avec une batterie du même type. Mettre au rebut les batteries usagées

conformément aux instructions du fabricant.

11. In addition, if the equipment is to be used with telecommunications circuits, take the following

precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically designed for

wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm. There may

be a remote risk of electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

EMI Warnings

WARNING:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements

that no modifications will be made to the equipment unless the changes or

modifications are expressly approved by Paradyne Corporation.

WARNING:

To Users of Digital Apparatus in Canada:

This Class A digital apparatus meets all requirements of the Canadian

interference-causing equipment regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du

règlement sur le matérial brouilleur du Canada.

Japan ITE Notice

This is a Class A product based on the standard of the Voluntary Control Council for

Interference from Information Technology Equipment (VCCI). If this is used near a radio or

television receiver in a domestic environment, it may cause radio interference. Install and

use the equipment according to the instruction manual.



*3163–A2–GL10–00*

Paradyne ACCULINK 3163 DSU Reference guide

Brand: Paradyne

Model: ACCULINK 3163 DSU

Category: Modems

Type: Reference guide

This manual is also suitable for

Download PDF

report

Paradyne ACCULINK 3163 DSU Reference guide

This manual is also suitable for

Paradyne ACCULINK 3163 DSU Reference guide

Related papers

Other documents