Woods DHH126T User manual

Brand: Woods

Model: DHH126T

Category: Lawnmowers

Type: User manual

This manual is also suitable for

OPER ATOR'S MANUAL

DISC HARROW

MAN1106

(Rev. 9/1/2015)

DHH108T

DHH126T

DHH144T

2 Introduction

Gen’l (Rev. 12/5/2011)

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods

dealer. Read manual instructions

and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual

are completed before releasing equipment to the owner.

The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that

all Dealer Check List items have been completed. Dealers can register all Woods product at

dealer.WoodsEquipment.com under Product Registration.

Failure to register the product does not diminish customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and

safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become

acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be

obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in

the United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and

satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.

Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary

tools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for

safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces

provided:

Model:

_______________________________

Date of Purchase:

_____________________

Serial Number:

(see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.

The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with

an exclamation mark) to indicate the degree of hazard for items of personal safety.

Introduction 3

MAN1106 (10/10/2014)

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

PARTS INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 32

REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER

4 Introduction

MAN1106 (10/10/2014)

SPECIFICATIONS

GENERAL INFORMATION

The purpose of this manual is to assist you in operating

and maintaining your Disc Harrow. Read it carefully. It

furnishes information and instructions that will help you

achieve years of dependable performance.

These instructions have been compiled from extensive

field experience and engineering data. Some informa-

tion may be general in nature, due to unknown and

varying operating conditions. However, through experi-

ence and these instructions, you should be able to

develop procedures suitable to your particular situa-

tion.

The illustrations and data used in this manual were cur-

rent at the time of printing. However, due to possible

inline production changes, your machine may vary

slightly in detail. We reserve the right to redesign and

change the machines as may be necessary without

notification.

Throughout this manual, references are made to right

and left direction. These are determined by standing

behind the tractor facing the direction of forward travel.

DHH108T DHH126T DHH144T

Working Width 108 inches 126 inches 144 inches

Weight 2590 lbs. 2770 lbs. 2950 lbs.

Number of Blades 24 28 32

Weight per Blade 108 lbs. 93 lbs. 81 lbs.

Horsepower 50 - 75 60 - 100 70 - 110

Hitch Pull-type, 1-1/4" Pin Pull-type, 1-1/4" Pin Pull-type, 1-1/4"Pin

Angling Front & Rear Front & Rear Front & Rear

0 - 21 degrees 0 - 21 degrees 0 - 21 degrees

(7 positions) (7 positions) (7 positions)

Blade Type Notched or Smooth Notched or Smooth Notched or Smooth

Blade Diameter 20" or 22" 20" or 22" 20" or 22"

Blade Spacing 9 inches 9 inches 9 inches

Axle Diameter 1-1/8" Square 1-1/8" Square 1-1/8" Square

Bearing Type Greaseable, Self-Aligning Greaseable, Self-Aligning Greaseable, Self-Aligning

Bearing Hangers Dual, 1/2" Plate, U-Bolt Triple, 1/2" Plate, U-Bolt Triple, 1/2" Plate, U-Bolt

U-Bolts Single, 3/4" Single, 3/4" Single, 3/4"

Frame Tube 4" x 3" 4" x 3" 4" x 3"

Disc Gang Tube 4" x 3" 4" x 3" 4" x 3"

Tire Size

9.5L x 15" Ag or 29" Used Aircraft 9.5L x 15" Ag or 29" Used Aircraft 9.5L x 15" Ag or 29" Used Aircraft

Single or Dual Single or Dual Single or Dual

Accessories Mud Scrapers, Furrow Fillers,

Rear Drawbar

Mud Scrapers, Furrow Fillers,

Rear Drawbar

Mud Scrapers, Furrow Fillers,

Rear Drawbar

Safety 5

DHH Disc Harrow (9/29/2014)

INSTALLATION

 Hydraulics must be connected as instructed in

this manual. Do not substitute parts, modify, or

connect in any other way.

TRAINING

 Safety instructions are important! Read all

attachment and power unit manuals; follow all

safety rules and safety decal information. (Replace-

ment manuals and safety decals are available from

your dealer. To locate your nearest dealer, check

the Dealer Locator at www.WoodsEquipment.com,

or in the United States and Canada call 1-800-319-

6637.) Failure to follow instructions or safety rules

can result in serious injury or death.

 If you do not understand any part of this manual

and need assistance, see your dealer.



Operators must be instructed in and be capable

of the safe operation of the equipment, its attach-

ments, and all controls. Do not allow anyone to

operate this equipment without proper instructions.



Never allow children or untrained persons to

operate equipment.



Keep hands and body away from pressurized

lines. Use paper or cardboard, not hands or other

body parts to check for leaks. Wear safety goggles.

Hydraulic fluid under pressure can easily penetrate

skin and will cause serious injury or death.



Make sure that all operating and service person-

nel know that if hydraulic fluid penetrates skin, it

must be surgically removed as soon as possible by

a doctor familiar with this form of injury or gan-

grene, serious injury, or death will result. CON-

TACT A PHYSICIAN IMMEDIATELY IF FLUID

ENTERS SKIN OR EYES. DO NOT DELAY.

PREPARATION



Check that all hardware is properly installed.

Always tighten to torque chart specifications

unless instructed otherwise in this manual.



Air in hydraulic systems can cause erratic oper-

ation and allows loads or equipment components

to drop unexpectedly. When connecting equipment

or hoses or performing any hydraulic maintenance,

purge any air in hydraulic system by operating all

hydraulic functions several times. Do this before

putting into service or allowing anyone to

approach the equipment.



Make sure all hydraulic hoses, fittings, and

valves are in good condition and not leaking before

starting power unit or using equipment. Check and

route hoses carefully to prevent damage. Hoses

must not be twisted, bent sharply, kinked, frayed,

pinched, or come into contact with any moving

parts. Operate moveable components through full

operational range to check clearances. Replace

any damaged hoses immediately.



After connecting hoses, check that all control

lever positions function as instructed in the Opera-

tor's Manual. Do not put into service until control

lever and equipment movements are correct.



Your dealer can supply original equipment

hydraulic accessories and repair parts. Substitute

parts may not meet original equipment specifica-

tions and may be dangerous.



Set tractor hydraulic relief valve at 2500 psi (170

bars) (17,000 kPa) to prevent injury and equipment

damage due to hydraulic system failure.



Remove accumulated debris from this equip-

ment, power unit, and engine to avoid fire hazard.



Make sure all safety decals are installed.

Replace if damaged. (See Safety Decals section for

location.)



Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.



Make sure attachment is properly secured,

adjusted, and in good operating condition.



Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely

fastened. Falling off power unit can result in death

from being run over or crushed. Keep foldable

ROPS system in “locked up” position at all times.

(Safety Rules continued on next page)

Safety is a primary concern in the design and

manufacture of our products. Unfortunately, our

efforts to provide safe equipment can be wiped

out by an operator’s single careless act.

In addition to the design and configuration of

equipment, hazard control and accident preven-

tion are dependent upon the awareness, con-

cern, judgement, and proper training of

personnel involved in the operation, transport,

maintenance, and storage of equipment.

It has been said, “The best safety device is an

informed, careful operator.” We ask you to be

that kind of operator.

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

6 Safety

DHH Disc Harrow (9/29/2014)

(Safety Rules continued from previous page)



A minimum 20% of tractor and equipment

weight must be on the tractor front wheels when

attachments are in transport position. Without this

weight, front tractor wheels could raise up result-

ing in loss of steering. The weight may be attained

with front wheel weights, ballast in tires or front

tractor weights. Weigh the tractor and equipment.

Do not estimate.



Consult local utilities before working. Know

location of all underground cables, pipelines, over-

head wires, and other hazards in working area and

avoid contact.

TRANSPORTATION



Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely

fastened. Falling off power unit can result in death

from being run over or crushed. Keep foldable

ROPS system in “locked up” position at all times.



Always raise unit and install transport locks

before transporting. Leak down or failure of

mechanical or hydraulic system can cause equip-

ment to drop.



Always attach safety chain to tractor drawbar

when transporting unit.



The maximum transport speed for towed and semi-

mounted machines is 20 mph (32 km/h). Regardless of

the maximum speed capability of the towing tractor, do

not exceed the implement’s maximum transport speed.

Doing so could result in:

• Loss of control of the implement and tractor

• Reduced or no ability to stop during braking

• Implement tire failure

• Damage to the implement or its components.



Use additional caution and reduce speed when

under adverse surface conditions, turning, or on

inclines.



Never tow this implement with a motor vehicle.



Always comply with all state and local lighting

and marking requirements.



Never allow riders on power unit or attachment.



Do not operate or transport on steep slopes.



Use extreme care and reduce ground speed on

slopes and rough terrain.



Do not operate or transport equipment while

under the influence of alcohol or drugs.

OPERATION



Do not allow bystanders in the area when oper-

ating, attaching, removing, assembling, or servic-

ing equipment.



Do not operate or transport equipment while

under the influence of alcohol or drugs.



Always comply with all state and local lighting

and marking requirements.



Operate only in daylight or good artificial light.



Keep hands, feet, hair, and clothing away from

equipment while engine is running. Stay clear of all

moving parts.



Never allow riders on power unit or attachment.



Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely

fastened. Falling off power unit can result in death

from being run over or crushed. Keep foldable

ROPS system in “locked up” position at all times.



Always sit in power unit seat when operating

controls or starting engine. Securely fasten seat

belt, place transmission in neutral, engage brake,

and ensure all other controls are disengaged

before starting power unit engine.



Look down and to the rear and make sure area

is clear before operating in reverse.



Use extreme care when working close to fences,

ditches, other obstructions, or on hillsides.



Do not operate or transport on steep slopes.



Do not stop, start, or change directions sud-

denly on slopes.



Use extreme care and reduce ground speed on

slopes and rough terrain.



Stop power unit and equipment immediately

upon striking an obstruction. Turn off engine,

remove key, inspect, and repair any damage before

resuming operation.



Watch for hidden hazards on the terrain during

operation.

(Safety Rules continued on next page)

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety 7

DHH Disc Harrow (9/29/2014)

(Safety Rules continued from previous page)

MAINTENANCE



Before servicing, adjusting, repairing or unplug-

ging, stop tractor engine, place all controls in neu-

tral, set park brake, remove ignition key.



Before dismounting power unit or performing

any service or maintenance, follow these steps:

disengage power to equipment, lower the 3-point

hitch and all raised components to the ground,

operate valve levers to release any hydraulic pres-

sure, set parking brake, stop engine, remove key,

and unfasten seat belt.



Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.



Never go underneath equipment (lowered to the

ground or raised) unless it is properly blocked and

secured. Never place any part of the body under-

neath equipment or between moveable parts even

when the engine has been turned off. Hydraulic

system leak down, hydraulic system failures,

mechanical failures, or movement of control levers

can cause equipment to drop or rotate unexpect-

edly and cause severe injury or death.



Make sure attachment is properly secured,

adjusted, and in good operating condition.



Never perform service or maintenance with

engine running.



Keep all persons away from operator control

area while performing adjustments, service, or

maintenance.



Tighten all bolts, nuts, and screws to torque

chart specifications. Check that all cotter pins are

installed securely to ensure equipment is in a safe

condition before putting unit into service.



Do not modify or alter or permit anyone else to

modify or alter the equipment or any of its compo-

nents in any way.



Your dealer can supply original equipment

hydraulic accessories and repair parts. Substitute

parts may not meet original equipment specifica-

tions and may be dangerous.



To prevent contamination during maintenance

and storage, clean and then cover hose ends, fit-

tings, and hydraulic ports with tape.



Do not allow bystanders in the area when oper-

ating, attaching, removing, assembling, or servic-

ing equipment.



Make sure all safety decals are installed.

Replace if damaged. (See Safety Decals section for

location.)



Do not disconnect hydraulic lines until machine

is securely blocked and system pressure is

released by operating valve levers.



Explosive separation of tire and rim parts can

cause serious injury or death. Release all air pres-

sure before loosening bolts on wheel.

STORAGE



To help prevent injury caused by a falling imple-

ment, always detach on a hard level surface.



Block equipment securely for storage.



Remove hydraulic hoses only after tractor is

turned off and all system pressure is released by

operating valve levers several times.



Keep children and bystanders away from stor-

age area.



Follow manual instructions for storage.



SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

8 Safety

MAN1106 (10/10/2014)

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure

washer; high-pressure water can enter through very small

scratches or under edges of decals causing them to peel

or come off.

Replacement safety decals can be ordered free from your

Woods dealer. To locate your nearest dealer, check the

Dealer Locator at www.WoodsEquipment.com, or in the

United States and Canada call 1-800-319-6637.

1 - SERIAL NUMBER PLATE

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

Safety 9

MAN1106 (10/10/2014)

5 - PN 19924

2 - PN 1003751

3 - PN 1004991

4 - PN 18865

7 - FRONT AMBER REFLECTOR (PN 1002940) Located on front of all gang tubes.

8 - REAR RED REFLECTOR (PN 57123) Located on rear of all gang tubes.

9 - SMV SIGN (PN 24611) (Not shown).

PN 1006348 - Located on Wheel Rims

6 - PN 55122

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

10 Operation

MAN1106 (10/10/2014)

OPERATION

The operator is responsible for the safe operation of

this equipment. The operator must be properly trained.

Operators should be familiar with the equipment, the

tractor, and all safety practices before starting opera-

tion. Read the safety rules and safety decals, page 5

through page 7.

The Disc Harrow is designed for a wide range of appli-

cations: leveling, grading, and discing. Recommended

tractor ground speed for most conditions is from 2 to 7

mph.



A minimum 20% of tractor and equipment

weight must be on the tractor front wheels when

attachments are in transport position. Without this

weight, front tractor wheels could raise up result-

ing in loss of steering. The weight may be attained

with front wheel weights, ballast in tires or front

tractor weights. Weigh the tractor and equipment.

Do not estimate.



Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely

fastened. Falling off power unit can result in death

from being run over or crushed. Keep foldable

ROPS system in “locked up” position at all times.



Never allow children or untrained persons to

operate equipment.



Do not allow bystanders in the area when oper-

ating, attaching, removing, assembling, or servic-

ing equipment.



NEVER GO UNDERNEATH EQUIPMENT. Never

place any part of the body underneath equipment

or between moveable parts even when the engine

has been turned off. Hydraulic system leak-down,

hydraulic system failures, mechanical failures, or

movement of control levers can cause equipment

to drop or rotate unexpectedly and cause severe

injury or death.

• Service work does not require going under-

neath implement.

• Read Operator's Manual for service instruc-

tions or have service performed by a qualified

dealer.



Keep hands, feet, hair, and clothing away from

equipment while engine is running. Stay clear of all

moving parts.



Stop power unit and equipment immediately

upon striking an obstruction. Turn off engine,

remove key, inspect, and repair any damage before

resuming operation.



Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.

PRE-OPERATION CHECK LIST

(Owner’s Responsibility)

___ Review and follow all safety rules and safety

decal instructions, page 5 through page 9.

___ Check all lubrication points and grease as

instructed in lubrication information.

___ Check that all hydraulic hoses and fittings are

in good condition and not leaking before start-

ing tractor. Check that hoses are not twisted,

bent sharply, kinked, frayed, or pulled tight.

Replace any damaged hoses immediately.

___ Raise and lower equipment to make sure air is

purged from hydraulic cylinders and hoses.

___ Make sure tractor 3-point lift links do not inter-

fere with hydraulic hoses or driveline through-

out full turning range.

___ Check that equipment is properly and securely

attached to tractor.

___ Check that all safety decals are installed and in

good condition. Replace if damaged.

___ Check that all hardware is properly installed

and secured.

___ Do not allow riders.

___ Make sure tractor ROPS or ROPS cab and

seat belt are in good condition. Keep seat belt

securely fastened during operation.

CAUTION

Operation 11

MAN1106 (10/10/2014)

CONNECT DISC HARROW TO TRACTOR

This Disc Harrow should be pulled behind tractors

within the engine horsepower rating specified on page

4. Do not exceed maximum engine horsepower rating

for a given model.

1. Attach Disc Harrow to drawbar using a 1-1/8"

clevis pin and clip.

2. Attach safety tow chain (7) to drawbar support.

Leave enough slack for turning. (See Figure 1).

3. Remove pin and rotate parking jack (6) to

horizontal position on tongue. Secure parking jack

with pin for storage during operation.

Figure 1. Connect Disc Harrow to Tractor

Lighting Connection (If Equipped)

1. Inspect wiring harnesses and connections to

ensure they are in good condition.

2. Route wiring harness (2) through hose holder (3) at

the hitch and be sure the harness can slide freely

in the holder. Do not allow wiring harness slack to

drag on the ground or become caught on tractor

protrusions.

3. Attach the wiring harness to the tractor.

Hydraulic Connection

1. Inspect hydraulic hoses to ensure they are in good

condition.

2. Clean the fittings before connecting them to the

tractor hydraulic ports.

3. Route the hoses through the hose holder at the

hitch and be sure the hoses can slide freely in the

holder. Do not allow hose slack to drag on the

ground or become caught on tractor protrusions.

4. Attach the hydraulic hoses to the tractor.

5. From the operator position, start tractor and raise

and lower Disc Harrow several times to purge

trapped air from the hydraulic cylinder.

Interference Check

1. Be sure that tractor 3-point lift links do not interfere

with hydraulic hoses or disc harrow frame.

2. Check for straight-ahead operation and at full

turning angles. If here is any interference, remove

the lower lift links.

3. Contact between tractor lift links and disc harrow

parts can cause damage, especially when turning.

DISC HARROW ATTITUDE ADJUSTMENT

For best results, always maintain a level disc attitude. A

level disc attitude will leave a slight ridge of material, in

the center, behind the rear gangs. A large ridge of

material will require the attitude to be adjusted forward.

a furrow, in the center, behind the rear gangs will

require the attitude to be adjusted to the rear. Attitude

adjustments can be made, while the disc harrow is con-

nected to the tractor, by following these instructions:

Forward Attitude Adjustment

(Shorten the Ratchet Jack)

1. Raise Disc Harrow to full height and secure with

transport lock.

2. Rotate ratchet jack (8) clockwise to adjust attitude

forward.

3. Release transport lock and resume operation.

check for proper attitude adjustment and repeat as

necessary.

Rear Attitude Adjustment

(Lengthen the Ratchet Jack)

1. Raise Disc Harrow to full height and secure with

transport lock.

2. Rotate ratchet jack counter-clockwise to adjust

attitude to the rear.

3. Release transport lock and resume operation.

Check for proper attitude adjustment and repeat as

necessary.

NOTICE

■

Excessive forward or rear attitude adjustment

will lead to poor finish and may cause equipment

damage or premature bearing failure.

12 Operation

MAN1106 (10/10/2014)

Note: Disc Harrow attitude should only be adjusted

using the ratchet jack. For instructions on adjusting atti-

tude rod spring tension, see ATTITUDE ROD ADJUST-

MENT.

Figure 2. Disc Harrow Attitude Adjustment

ATTITUDE ROD ADJUSTMENT

A properly adjusted attitude rod will have a snug, but

not compressed, rear coil spring when the Disc Harrow

is in transport mode. Adjustments can be made, by fol-

lowing these instructions.

1. Raise Disc Harrow to full height and secure with

transport lock.

2. Loosen outer nut (9) to allow adjustment.

3. If rear spring (5) is loose, tighten inner nut (9) until

spring is snug.

4. If rear spring is compressed, loosen inner nut until

spring is snug.

5. Tighten outer nut while retaining inner nut to lock

adjustment.

Figure 3. Attitude Rod Adjustment

ANGLING DISC BLADES

All disc gangs are fully adjustable with 7 positions

between 0 and 21 degrees. The disc setting becomes

more aggressive with increased gang angle. The

greater the disc angle, the greater the material turn

over. Adjustments can be made to the disc gang

angles by following these instructions:

1. Raise Disc Harrow until blades are just off the

ground.

2. Remove klik pin (6) from lock plate (4).

3. Pull lock plate up and lock in place with klik pin.

4. Grasp lock plate and handle (5) and slide carriage

to desire position.

5. Hold lock plate and remove klik pin.

6. Push lock plate down in new position and secure

with klik pin.

7. Repeat for remaining disc gangs.

Figure 4. Angling Disc Blades

NOTICE

■

Although front and rear gang sets can be

adjusted independently, right and left gangs

should always be adjusted to the same angle by

not allowing open positions between carriages.

Operation 13

MAN1106 (10/10/2014)

ADJUSTING DISC OPERATING DEPTH

The operating depth of the Disc Harrow is controlled by

installing stroke control spacers on the hydraulic cylin-

der rod. A cylinder stroke control kit is included with the

Disc Harrow. The operating depth of the Disc Harrow

can be set by following these instructions:

1. Operate the Disc Harrow with all spacers removed.

make adjustments to the hydraulic cylinder until the

desired operating depth is achieved.

2. Stop tractor, set parking brake, stop engine,

remove key, and unfasten seat belt.

3. Measure amount of exposed cylinder rod and

select required spacers (27).

4. Return to tractor, extend hydraulic cylinder to

maximum length. Stop engine, remove key.

5. Install selected spacers on cylinder rod. keep

remaining spacers installed on wheel arm (1) for

future use.

6. Return to tractor, lower cylinder against spacers.

Continue operation.

7. Check that desired operating depth was achieved.

Repeat steps as necessary to achieve desired

depth.

NOTE: Spacer sizes required will depend on tire

type and size installed on disc.

Figure 5. Adjusting Disc Operating Depth

STORAGE



To help prevent injury caused by a falling imple-

ment, always detach on a hard level surface.



Block equipment securely for storage.



Remove hydraulic hoses only after tractor is

turned off and all system pressure is released by

operating valve levers several times.



Keep children and bystanders away from stor-

age area.



Follow manual instructions for storage.

Disc Harrow should be stored with disc blades lowered

to the ground after each use. Disconnect the Disc Har-

row by following these instructions:

1. Lower Disc Harrow to ground.

2. Securely block in front of and behind wheels to

prevent wheel rotation.

3. Attach parking jack and raise tongue weight off

tractor drawbar.

4. Remove hydraulic hoses only after tractor is turned

off and all system pressure is released by

operating valve levers several times. Hang hoses

in hose holder on disc hitch.

5. Remove wiring harness (if equipped) and hang on

hose holder.

6. Remove safety tow chain.

7. Remove retainer pin and high strength drawbar

pin.

TRANSPORTING



Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely

fastened. Falling off power unit can result in death

from being run over or crushed. Keep foldable

ROPS system in “locked up” position at all times.



Always raise unit and install transport locks

before transporting. Leak down or failure of

mechanical or hydraulic system can cause equip-

ment to drop.



Always attach safety chain to tractor drawbar

when transporting unit.



Never exceed 20 mph (32.2 km/h) during trans-

port.



Never allow riders on power unit or attachment.



Do not operate or transport on steep slopes.



Do not operate or transport equipment while

under the influence of alcohol or drugs.



Use additional caution and reduce speed when

under adverse surface conditions, turning, or on

inclines.

■

Never tow this implement with a motor vehicle.

14 Operation

MAN1106 (10/10/2014)



Always comply with all state and local lighting

and marking requirements.

Figure 6. Transport Lock - Transport Position

Lock-Up

Always transport the Disc Harrow in the raised, locked

position.

1. Raise Disc Harrow with hydraulic cylinder to

maximum height.

2. Rotate transport lock (2) into position over cylinder

rod. (See Figure 6).

3. Lower disc harrow against transport lock.

4. To lower Disc Harrow for operation, extend

hydraulic cylinder to release transport lock. Rotate

transport lock away from cylinder rod. (See Figure

7).

5. Lower disc to desired operating height.

Figure 7. Transport Lock - Operating Position

CAUTION

Service 15

MAN1106 (10/10/2014)

SERVICE

The information in this section is written for operators

who possess basic mechanical skills. If you need help,

your dealer has trained service technicians available.

For your protection, read and follow the safety informa-

tion in this manual.



Before servicing, adjusting, repairing or unplug-

ging, stop tractor engine, place all controls in neu-

tral, set park brake, remove ignition key, and wait

for all moving parts to stop.



Never perform service or maintenance with

engine running.



NEVER GO UNDERNEATH EQUIPMENT. Never

place any part of the body underneath equipment

or between moveable parts even when the engine

has been turned off. Hydraulic system leak-down,

hydraulic system failures, mechanical failures, or

movement of control levers can cause equipment

to drop or rotate unexpectedly and cause severe

injury or death.

• Service work does not require going under-

neath.

• Read Operator's Manual for service instruc-

tions or have service performed by a qualified

dealer.



Keep all persons away from operator control

area while performing adjustments, service, or

maintenance.



Always wear relatively tight and belted clothing

to avoid getting caught in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.



If you do not understand any part of this manual

and need assistance, see your dealer.

LUBRICATION

Do not let excess grease collect on or around parts,

particularly when operating in sandy areas.

See Figure 8 for lubrication points and frequency for

lubrication based on normal operating conditions.

Severe or unusual conditions may require more fre-

quent lubrication.

Use a lithium grease of #2 consistency with a MOLY

(molybdenum disulfide) additive for all locations. Be

sure to clean fittings thoroughly before attaching

grease gun. One good pump of most guns is sufficient

when lubrication schedule is followed.

Figure 8. Lubrication Points

NOTICE

■

Do not use excessive amounts of grease on

bearings (5). Excessive amounts of grease can

cause seal damage and/or premature bearing fail-

ure.

DISC & BEARING REPLACEMENT

Disassemble Gang

1. Lower Disc Harrow to ground.

2. Securely block front and rear wheels to prevent

wheel rotation.

CAUTION

1. Hitch pivot points . . . . . . . . . 40 hrs.

2. Attitude rod . . . . . . . . . . . . . 20 hrs.

3. Wheel bearings . . . . . . . . . . 20 hrs.

4. Wheel mount pivot points . . 40 hrs.

5. Disc gang axle bearings . . . 80 hrs.

16 Service

MAN1106 (10/10/2014)

3. Remove carriage bolts (9) and nuts (10) from all

bearings on disc harrow gang.

4. Remove gang assembly from bearing hangers by

raising Disc Harrow to full height. Secure with

transport lock.

5. With gang assembly removed from bearing

hangers, remove outer and inner jam nuts (18),

axle washer (14) and end spacer (17).

6. Slide discs, spacers, washer and bearings off axle

as needed to replace desired disc(s) and

bearing(s).

NOTE: Maintain proper order of discs, spacers,

washers and bearings for reassembly. (See Parts

page 25).

Figure 9. Disc Gang Assembly

Assemble Gang

1. Reassemble gang with new disc(s) and bearing(s)

in reverse order of disassembly steps.

NOTE: Maintain proper order of discs, spacers,

and bearings for reassembly. (See Parts page 25).

2. Install end spacer, axle washer and inner jam nut.

Torque inner jam nut to 450 lbs-ft.

3. Install outer jam nut. Torque outer jam nut to 450

lbs-ft.

4. Align bearings with bearing hangers. Lower disc to

ground.

5. Install carriage bolts and nuts on all bearings.

SERVICING TIRES SAFELY

Used Aircraft Tires (Figure 10)

Do not attempt to mount a tire unless you have the

proper equipment and experience to perform the job.

Always maintain the correct tire pressure. Do not inflate

tires above the recommended pressure. Never weld or

heat a wheel and tire assembly. The heat can cause an

increase in air pressure and result in a tire explosion.

Welding can structurally weaken or deform the wheel.

When inflating tires, use a clip-on chuck and an exten-

sion hose long enough to allow you to stand to the side

— not in front of or over the tire assembly. Use a safety

cage if available.

Check wheels for low pressure, cuts, bubbles, dam-

aged rims, or missing lug bolts and nuts.

Never remove split rim assembly hardware (A) with the

tire inflated.

Figure 10. Split Rim Tire Servicing

WARNING

PN 1006348

(Rev. 9/1/2015)

Service 17

MAN1106 (10/10/2014)

CLEANING

After Each Use

●

Remove large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

●

Inspect machine and replace worn or damaged

parts.

●

Replace any safety decals that are missing or not

readable.

Periodically or Before Extended Storage

●

Clean large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

●

Remove the remainder using a low-pressure water

spray.

1. Be careful when spraying near scratched or torn

safety decals or near edges of decals as water

spray can peel decal off surface.

2. Be careful when spraying near chipped or

scratched paint as water spray can lift paint.

3. If a pressure washer is used, follow the advice of

the pressure washer manufacturer.

●

Inspect machine and replace worn or damaged

parts.

●

Sand down scratches and the edges of areas miss-

ing paint and coat with Woods spray paint of

matching color (purchase from your Woods

dealer).

●

Replace any safety decals that are missing or not

readable (supplied free by your Woods dealer).

See Safety Decals section for location drawing.



18 Assembly

MAN1106 (10/10/2014)

ASSEMBLY INSTRUCTIONS

DEALER SET-UP INSTRUCTIONS

Assembly of this Disc Harrow is the responsibility of the

WOODS dealer. The Disc Harrow is shipped in 3 sec-

tions: Frame kit, gang kits and finishing kit. Recom-

mended torque values for hardware are located on

page 31. It should be delivered to the owner completely

assembled, lubricated and adjusted for normal condi-

tions.

Complete the Dealer Checklist on page 21 when

assembly is complete and Disc Harrow is delivered to

the owner.



NEVER GO UNDERNEATH EQUIPMENT. Never

place any part of the body underneath equipment

or between moveable parts even when the engine

has been turned off. Hydraulic system leak-down,

hydraulic system failures, mechanical failures, or

movement of control levers can cause equipment

to drop or rotate unexpectedly and cause severe

injury or death.

• Service work does not require going under-

neath implement.

• Read Operator's Manual for service instruc-

tions or have service performed by a qualified

dealer.



Keep all persons away from operator control

area while performing adjustments, service, or

maintenance.



Always wear relatively tight and belted clothing

to avoid entanglement in moving parts. Wear

sturdy, rough-soled work shoes and protective

equipment for eyes, hair, hands, hearing, and head;

and respirator or filter mask where appropriate.

The Disc Harrow is to be assembled by following

these instructions:

1. Stand frame kit on side. Remove banding on hitch

and unfold.

2. Position frame horizontal on jack stands or blocks

so wheels and tires can be installed.

3. Install parking jack, hose holder and safety chain,

ratchet jack, wheels and tires, and hydraulic

cylinder.

4. Install hydraulic fittings and run hydraulic hoses

through hose loop on frame and down right hand

frame tube to the front of the disc frame. Hoses

should pass under the self-level arm and lay on top

of the hitch as shown in Figure 1 on page 11.

5. Starting at the side of the rear frame tube,

assemble SMV and lighting brackets and slide into

place. Install Slow Moving Vehicle sign, LED

lamps, and enhancer module.

6. Run main wiring harness through hose holder,

down left hand frame tube to the rear of the disc.

Connect main harness to enhancer module and

rear harnesses between module and lamps.

7. Use hydraulics to lift disc frame for gangs to be

installed. Rotate transport lock-up into place.

8. Install gang tubes with 1” hardware, with red

reflectors to the rear.

9. Arrange gang assemblies under tube in

configuration shown in Figure 11 on page 19.

10. Attach bearing hangers to gang tubes using U-

bolts. Torque lock nuts on U-bolts to 300 lbs-ft.

(Install mud scraper mount brackets in this step if

equipped). See page 20.

11. Fully test all gang adjustments, attitude

adjustment, and hydraulics system. Attach stroke

control spacers to wheel arm.

12. Complete Dealer Checklist before delivery to

customer.

CAUTION

Assembly 19

MAN1106 (10/10/2014)

Figure 11. Disc Harrow Assembly

Accessory Installation

All Disc Harrow factory accessories include all neces-

sary hardware for installation. Assemble and install fac-

tory accessories by following these instructions:

Furrow Fillers

1. Attach furrow filler mount (2) by sliding carriage

bolts (5) into slotted bumper washer (12) and

securing with lock nuts (6).

2. Install furrow filler blade (purchased separately)

and secure with furrow filler washer (3) and lock

nut (4).

Figure 12. Furrow Filler Installation

(Rev. 9/1/2015)

20 Assembly

MAN1106 (10/10/2014)

Mud Scrapers

1. Install short brackets (3) on the U-bolts of the inner

and outer bearing hangers of the forward swept

gangs. (Right front and left rear) See Figure 11 on

page 19 for sweep direction illustration.

2. Install long brackets on the U-bolts of the inner and

outer bearing hangers of the rear swept gangs.

(Left front and right rear) See Figure 11 on page 19

for sweep direction illustration.

3. Install scraper mount angles (2) to the brackets

using carriage bolts (7) and flanged lock nuts (8).

Install furrow filler scrapers, if equipped, at this

time. (Included with furrow filler kit, part number

1037390).

4. Install mud scrapers to the scraper mount angle

with carriage bolts and lock nuts.

5. Adjust mud scrapers to desired spacing.

Adjustments can be made to the mount angle or

each individual scraper to achieve desired setting.

Figure 13. Mud Scraper Installation

Rear Drawbar

1. Install rear drawbar to drawbar mounts on rear of

Disc Harrow frame using supplied hardware.

Figure 14. Rear Drawbar Installation

Page is loading ...

Woods DHH126T User manual

Brand: Woods

Model: DHH126T

Category: Lawnmowers

Type: User manual

This manual is also suitable for

Download PDF

report

Woods DHH126T User manual

This manual is also suitable for

Woods DHH126T User manual

Related papers

Other documents