Cineversum ial-DLP User manual

Brand: Cineversum

Model: ial-DLP

Category: Projectors

Type: User manual

HOME CINEMA

CINEVERSUM 60/70

INSTALLATION MANUAL

22042004 R5976763/00

Barco nv Home Cinema

Noordl

aan 5, B-8520 Kuurne

Phone: +32 56.36.89.69

Fax: +32 56.36.83.54

E-mail:

salesassistantht.bc[email protected]

Visit us at the web: www.homecinema.barco.com

Printed in Taiwan

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-

ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the

program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this

publication; these changes are incorporated in new editions of this publication.

stored in a retrieval system without the prior written consent of Barco.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC r

ules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to

cause harmful interference in which case the user is encouraged to try to correct the interference by one or more of the following measures.

Introduction to the user :

If this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the

following measures :

• Re-orientation of the receiving antenna for the radio or television.

• Relocate the equipment with respect to the receiver.

• Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.

• Fasten cables connectors to the equipment by mounting screws.

The use of shielded cables is required to comply within the limits of Part 15 of FCC rules and EN55022.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser

must immediately inspect all delivered goods for damage incurred during tr

ansport, as well as for material and manufacturing faults Barco

must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,

at latest 30 days after the transfer of risks. In the event of justified notice of compliant, Barco can repair the fault or provide a replacement

at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a

reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or

indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component

of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties

guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,

in particular if the systems are commissioned operated in

correctly or if, after the transfer of risks, the goods are subject to influences not

agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are

system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as

well as normal maintenance are not subject to the

guarantee provided by Barco either.

The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by

the customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.

All brand and product names mentioned in th

is manual serve as comments or examples and are not to be understood as advertising for

the products or their manufactures.

Table of contents

TABLE OF CONTENTS

1. Packaging and Dimensions ....................................................................................... 3

1.1 Box content............................................................................................................................ 3

1.2 Projector Packaging................................................................................................................... 3

1.3 Dimensions............................................................................................................................ 4

2. Installation Guidelines.............................................................................................. 7

2.1 Safety Warnings....................................................................................................................... 7

2.2 General . ............................................................................................................................... 7

2.3 Projector Configuration and Position ................................................................................................. 8

2.4 Safety Area around projector ........................................................................................................10

2.5 Cleaning the lens. . ...................................................................................................................10

2.6 Vertical lens shift ..................................................................................................................... 11

2.7 Battery Insertion in the Remote Control.............................................................................................12

2.8 Ceiling Mount assembly. . . ...........................................................................................................13

3. Connections.........................................................................................................15

3.1 Removing the Connector cover. . ....................................................................................................15

3.2 Power Connection....................................................................................................................15

3.3 Input facilities . . . . . . ...................................................................................................................16

3.4 S-Video input . . . . . . ...................................................................................................................17

3.5 Composite Video input ...............................................................................................................18

3.6 5-Cable input .........................................................................................................................18

3.7 Component Input . . ...................................................................................................................20

3.8 Digital Visual Interface (DVI) input. . . ................................................................................................21

3.9 Computer input (RGB analog) .. . ....................................................................................................22

3.10 RS232-422 IN connection ...........................................................................................................22

3.11 Trigger outputs . . . . ...................................................................................................................23

4. Getting Started......................................................................................................25

4.1 Terminology overview................................................................................................................25

4.2 Switching on..........................................................................................................................27

4.3 Lamp runtime.........................................................................................................................27

4.4 Switching from operational mode to standby. . . .....................................................................................28

4.5 Switching off the projector ...........................................................................................................28

4.6 Temperature error DMD..............................................................................................................28

4.7 Using the RCU .......................................................................................................................28

4.8 Projector Address ....................................................................................................................29

4.9 Controlling the projector..............................................................................................................29

5. Getting used to the menu structure.............................................................................31

5.1 How to start up the menus........................................................................................................... 31

5.2 How to use the menus ...............................................................................................................31

5.3 How to make an adjustment .........................................................................................................32

5.4 Access Control via a password...................................................................................................... 32

6. Source Selection ...................................................................................................33

6.1 Selecting a source ...................................................................................................................33

7. Image Settings menu ..............................................................................................35

7.1 Image settings menu overview ...................................................................................................... 35

7.2 Starting the Image settings menu ................................................................................................... 35

7.3 Brightness ............................................................................................................................36

7.4 Contrast...............................................................................................................................36

7.5 Saturation.............................................................................................................................36

7.6 Tint (hue) . . . ..........................................................................................................................37

7.7 Sharpness . . ..........................................................................................................................38

7.8 Gamma ...............................................................................................................................38

7.9 Color Temperature ...................................................................................................................39

7.9.1 Predefined Color Temperature ................................................................................................39

7.9.2 Custom Color Balance ........................................................................................................40

7.9.3 Color standard . . ...............................................................................................................40

7.10 White peak . ..........................................................................................................................42

8. Advanced Settings.................................................................................................43

8.1 Advanced settings menu overview ..................................................................................................43

8.2 Start up the Advanced settings ......................................................................................................43

8.3 Aspect Ratio..........................................................................................................................44

8.4 Image Position .......................................................................................................................46

8.4.1 Horizontal shift.................................................................................................................46

8.4.2 Horizontal size.................................................................................................................47

8.4.3 Vertical shift....................................................................................................................48

8.4.4 Vertical size....................................................................................................................49

8.5 Blanking ..............................................................................................................................50

R5976763 CINEVERSUM 60/70 22042004

Table of contents

8.6 Input Balance. . . . . . ...................................................................................................................51

8.6.1 Introduction to Input Balance. . ................................................................................................52

8.6.2 Adjusting the Input Balance for RGB signals ................................................................................. 53

8.6.3 Input balance for YUV signals. ................................................................................................ 54

8.6.4 Returning to the factory defaults ..............................................................................................55

9. Installation menu...................................................................................................57

9.1 Installation menu overview...........................................................................................................57

9.2 Start up the Installation menu........................................................................................................57

9.3 Input Slots . . ..........................................................................................................................58

9.3.1 5 RCA input selection (RGB/component input). . .............................................................................58

9.3.2 Reset a single input ........................................................................................................... 59

9.3.3 Reset all inputs ................................................................................................................59

9.4 File service ...........................................................................................................................60

9.4.1 Auto search ....................................................................................................................60

9.4.2 Film mode......................................................................................................................60

9.4.3 Color Space.................................................................................................................... 61

9.5 Internal pattern .......................................................................................................................62

9.6 When no signal . . . . ...................................................................................................................63

9.7 Source transition .....................................................................................................................63

9.8 On Screen Display Configuration....................................................................................................64

9.8.1 Menu position.................................................................................................................. 64

9.8.2 Bar scale status................................................................................................................65

9.8.3 Bar scale position..............................................................................................................65

9.8.4 Message status................................................................................................................ 66

9.9 Language support . ...................................................................................................................66

9.10 Vertical keystone .....................................................................................................................67

9.11 Horizontal keystone ..................................................................................................................68

9.12 Global keystone ......................................................................................................................69

9.13 Orientation............................................................................................................................69

10.Service menus......................................................................................................71

10.1 Service menu overview .............................................................................................................. 71

10.2 Start up the Service menu ...........................................................................................................71

10.3 Identification screen . . . ...............................................................................................................72

10.4 Password.............................................................................................................................72

10.4.1 Enable-disable password. . ....................................................................................................72

10.4.2 Modify password...............................................................................................................73

10.5 IR address............................................................................................................................74

10.6 RS232 address . . . . ...................................................................................................................74

10.7 Serial communication ................................................................................................................74

10.7.1 Baudrate setup . ...............................................................................................................74

10.7.2 Serial communication interface selection.....................................................................................75

10.8 Thermal Diagnosis ...................................................................................................................76

10.9 I2C Diagnosis . . . . . ...................................................................................................................76

A. Specifications .......................................................................................................77

A.1 Specifications for CineVERSUM 60 .................................................................................................77

A.2 Specifications for CineVERSUM 70 .................................................................................................78

B. Maintenance .........................................................................................................81

B.1 Error reporting via the LEDs .. . . . .................................................................................................... 81

Glossary .................................................................................................................83

Index......................................................................................................................85

2 R5976763 CINEVERSUM 60/70 22042004

1. Packaging and Dimensions

1. PACKAGING AND DIMENSIONS

Overview

• Box content

• Projector Packaging

• Dimensions

1.1 Box content

CEE7

European power plug to connect the power cord to the wall outlet.

ANSI 73.11

American power plug to connect the power cord to the wall outlet.

Content

• 1 CineVERSUM 60 or CineVERSUM 70 projector

• 1 remote control unit RCU + 2 batteries.

• 2 power cables with outlet plug type CEE7 and ANSI 73.11.

• 1 spanner to shift the lens

• 1 owners manual European languages (English, French, German, Italian, Spanish)

• 1 owners manual Asian languages (Chinese, Japanese)

• 1 installation manual

• 1 safety manual multilingual

1.2 Projector Packaging

Way of Packaging

The projector is packed in a carton box. To provide protection during transportation, the projector is surrounded with foam. The

package is secured with banding and fastening clips.

To unpack

1. Pull off the adhesive tape or cut the adhesive tape but take care not to insert the knife too deep otherwise the projector can be

damaged.

2. Take the projector out of its shipping carton, remove the foam rubber and place it on a table. (image 1-1)

R5976763 CINEVERSUM 60/70 22042004

1. Packaging and Dimensions

Image 1-1

Projector packaging

Save the original shipping carton and packing ma

terial, they will be necessary if you ever have to ship your

projector. For maximum protection, repack your projector as it was originally packed at the factory.

1.3 Dimensions

Left side view

Image 1-2

Left side view

A Air outlet

R5976763 CINEVERSUM 60/70 22042004

1. Packaging and Dimensions

Right side view

Image 1-3

Right side view

A Air inlet

B Adjustable feet

Front view

Image 1-4

Front view

A Air outlet

R5976763 CINEVERSUM 60/70 22042004

1. Packaging and Dimensions

Bottom view

Image 1-5

Bottom view

A Vertical lens shift bolt

B M8 bolt for security chain when ceiling mounted

C Air inlet

R5976763 CINEVERSUM 60/70 22042004

2. Installation Guidelines

2. INSTALLATION GUIDELINES

Overview

• Safety Warnings

• General

• Projector Configuration and Position

• Safety Area around projector

• Cleaning the lens

• Vertical lens shift

• Battery Insertion in the Remote Control

• Ceiling Mount assembly

Before installing the projector, read first the safety instructions in the safety manual delivered with the pro-

jector and also the safety pages in this manual.

2.1 Safety Warnings

Mercury Vapor Warnings

Keep the following warnings in mind when using the projector. The lamp used in the projector contains mercury. In case of a lamp

rupture, explosion there will be a mercury vapor emission. In order to minimize the potential risk of inhaling mercury vapors:

• Ensure the projector is installed only in ventilated rooms.

• Replace the lamp module before the end of its operational life.

• Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a pregnant

woman).

• Seek medical attention if unusual health conditions occur after a lamp rupture, explosion, such as headache, fatigue, shortness

of breath, chest-tightening coughing or nausea.

2.2 General

Ambient Temperature Conditions.

Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to

the optimum use of the projection system.

Max. ambient temperature : 40°C or 104 °F

Min. ambient temperature : 10 °C or 50 °F

The projector will not operate if ambient air temperature falls outside this range (10°C- 40°C or 50°F-104°F).

Storage temperature: -35°C to +65°C (-31°F to 149°F)

Humidity Conditions

Storage: 0 to 98 % RH Non-condensing

Operation: 0 to 95 % RH Non-condensing

Environment

Do not install the projection system in a site near heat sources

such as radiators or air ducts, or in a place subject to direct sunlight,

excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not

excessive.

Environment condition check

A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets. For

installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or

similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading

performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean

air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a

feasible solution then measures to relocate the projector to a clean air environment should be considered.

R5976763 CINEVERSUM 60/70 22042004

2. Installation Guidelines

Only ever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning optical parts, never

use industrial strength cleaners on the projector’s optics as these will degrade optical coatings and damage sensitive optoelectronics

components. Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contam-

inants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will

be non-effective and impracticable. Damage of this nature is under no circumstances covered under the manufacturer’s warranty

and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any

repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne

particles in the environment of the projector. The manufacturer reserves the right to refuse repair if a projector has been subject to

wantful neglect, abandon or improper use.

Special Care for Laser Beams

Special care should be used when DLP projectors are used in the same room as performant laser equipment. Direct or indirect hitting

of a laser beam on to the lens can severely damage the Digital MicroMirror Devices™ in which case there is a loss of warranty

Which screen type ?

There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear

projection applications.

Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount

of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain.

The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10)

or more. The choice between higher and lower gain screens is largely a matter of personal preference and another consideration

called the Viewing angle. In considering the type of screen to choose, determine where the viewers will be located and go for the

highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle. For more information

about screens, contact your local screen supplier.

What image size? How big should the image be?

The projector is designed for an optimum screen width of :

• For CineVERSUM 60 : min 1.30 m (52”) to max 1.78 m (70”)

• For CineVERSUM 70 : min 1.55 m (61") to max 1.98 m (78”)

(depending on the ambient light conditions), with an aspec

t ratio of 16 to 9.

Depending on the used lens, the minimum and maximum diagonal screen sizes are :

For CineVERSUM 70

R9010080

Short throw lens (1.4 - 1.8) Min : 0.80 m (32”) Max. 6.35 m (250”)

R9010081

Long throw lens (1.8 - 2.4) Min : Wide : 1 m (40”)

Min : Tele : 0.76 m(30”)

Max : Wide : 7.60 m (300”)

Max : Tele : 5.60 m (222”)

For CineVERSUM 60

R9002460

Short throw l

ens (1.7 - 2.25)

Min:1m(39”) Max. 5 m (200”

)

R9002461

Long throw lens (2.25 – 3) Min : Wide : 0.8 m (32”)

Min : Tele : 0.60 m(24”)

Max : Wide : 6.0 m (240”)

Max : Tele : 4.50 m (178”)

2.3 Projector Configuration and Position

Which configuration can be used?

The projector can be installed to project images in four different configurations:

• Front/table

• Rear/table

• Front/ceiling

• Rear/ceiling

Positioning the projector

• The projector should be installed perpendicular with the screen on a distance PD and water leveled in both directions. The

mounting positions in the following image is shown for a nominal lens position.

• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out the colors,

making viewing difficult . Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

• The projector lens should be centered horizontally in the middle of the screen.

R5976763 CINEVERSUM 60/70 22042004

2. Installation Guidelines

Try to avoid an inclination of the projector (forwards, backwards, to the left or to the right) as this will result in

a keystone deformation of the image. This deformation can be corrected with the keystone function but with

a loss of resolution as result.

The drawing is given for a table mounted projector. The same is valid for a ceiling mounted projector.

Image 2-1

Table mounted configuration

V1 Side view

V2 Top view

V3 Back view

PD Distance projector - screen

CD Distance bottom side projector - floor

SH Screen height

B Distance bottom side screen - floor

C Distance bottom side projector - perpendicular light axes

SW Screen width

For CineVERSUM 70:

Lens

1.4 - 1.8

Wide : PD = 1.4 x SW

Tele : P D = 1.8 x SW

CD=B+C-5.9cm

1.8 - 2.4

Wide : PD = 1.8 x SW

Tele : P D = 2.8 x SW

CD=B+C-5.9cm

With C = 0.25 x SH

R5976763 CINEVERSUM 60/70 22042004

2. Installation Guidelines

For CineVERSUM 60:

Lens

1.7 - 2.25

Wide : PD = 1.7 x SW

Tele : PD = 2.25 x SW

CD=B+C-5.9cm

2.25 - 3

Wide : PD = 2.25 x SW

Tele : P D = 3 x S W

CD=B+C-5.9cm

With C = 0.23 x SH

2.4 Safety Area around projector

Safety area

Make sure the projector is located so that the air inlets and outlets for the cooling system are not obstructed. Leave at least 50 cm

between the projector and an object next t

o the projector.

Image 2-2

Do not place inflammable materials within the safety area.

2.5 Cleaning the lens

To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have de-

veloped recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from

thelensbyblo

wing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.

Necessary tools

Toraysee

cloth, order number : R379058.

Howtocleanthelens?

Proceed as follow :

1. Always wipe lenses with a CLEAN Toraysee

cloth.

2. Always wipe lenses in a single direction.

Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.

3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.

4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.

Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth.

Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.

10 R5976763 CINEVERSUM 60/70 22042004

2. Installation Guidelines

Other lenses can also be cleaned safely with this Toraysee

cloth.

2.6 Vertical lens shift

What can be done ?

The image can be shifted in a vertical way to position the image correctly on the screen.

Necessary tools

Spanner delivered in the package

How to shift the lens ?

1. Turn the lens shift bolt on the bottom side of the projector, just below the lens, until the desired image position is obtained.

(image 2-3)

When table mounted, turning to the left (clockwise) will shift the image upwards. Turning to the right (

counter clockwise), will shift

the image downwards.

Image 2-3

Vertical lens shift bolt

A Lens shift bolt

R5976763 CINEVERSUM 60/70 22042004

2. Installation Guidelines

Vertical lens shift ranges

Image 2-4

Vertical lens shift

The distance between the middle of the projected image and the perpendicular line from the projector.

For CineVERSUM 60 :

• A = 0.275 x SH

•B=0.86xSH

For CineVERSUM 70 :

•A=0.24xSH

• B = 0.625 x SH

2.7 Battery Insertion in the Remote Control

Where to find the batteries

The batteries are not placed in the remote cont

rol to avoid remote control operation in its package, resulting in a shorter battery life

time.

How to install the batteries

1. Push the cover tab (A) with the fingernail a little backwards and pull upwards the cover top (B). (image 2-5)

2. Slide the cover forwards to remove. (image 2-6)

3. Push the battery body towards the spring and lift it up to remove. (image 2-7)

4. Insert two AA size batteries, making sure t

he polarities match the + and – marks inside the battery compartment (image 2-7).

5. Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place

(image 2-6).

R5976763 CINEVERSUM 60/70 22042004

2. Installation Guidelines

Image 2-5

Battery cover unlock

Image 2-6

Battery cover removal

Image 2-7

Battery removal

2.8 Ceiling Mount assembly

Overview

eiling mount is available to mount the projector to the ceiling. Always use this ceiling mount.

Order number : R9852060

For a more detailed description on how to mount the ceiling mount, consult the ceiling mount installation manual (R5976750) which

can be found in the box of the ceiling mount assembly or separately ordered by Barco.

R5976763 CINEVERSUM 60/70 22042004

2. Installation Guidelines

14 R5976763 CINEVERSUM 60/70 22042004

3. Connections

3. CONNECTIONS

Overview

• Removing the Connector cover

• Power Connection

• Input facilities

• S-Video input

• Composite Video input

• 5-Cable input

• Component Input

• Digital Visual Interface (DVI) input

• Computer input (RGB analog)

• RS232-422 IN connection

• Trigger outputs

3.1 Removing the Connector cover

What is behind this cover ?

The power connector and all inputs are situated behind this cover.

How to remove the cover ?

1. Loosen the locking screw. (image 3-1)

2. Left up at the bottom and pull on the cover to loose.

The cover makes a loud ’snap’ when removed. This is normal and does not damage the cover.

Image 3-1

Removing the input cover

When all connections are done, close the cover again and fix the locking screw.

3.2 Power Connection

AC Power (mains) cord connection

Use the supplied power cord to connect your projector to the wall outlet.

Plug the female power connector into the male connector at the back of the projector.

Plug the male connector into wall outlet.

R5976763 CINEVERSUM 60/70 22042004

3. Connections

ASPECT

RATIO

12V TRIGGER

SCREEN

S-VIDEO VIDEO V

R/Pr

B/Pb

G/Y

Pr Pb Y

RS232/RS422

CONTROL

DVI INPUT

VGA INPUT

COMPONENT

VIDEO INPUT RGB/COMPONENT INPUT

Image 3-2

The power input is auto-ranging from 90 to 240 VAC.

About the power cord

Mainslead(ACPowercord)withCEE7plugupto16A

The colors of the mains lead are colored in accordance with the following code:

• Green-and-yellow: Earth (safety earth)

• Blue: Neutral

•Brown:Line

3.3 Input facilities

Overview

•S-Video

• Video

• 5 cable input on RCA

-RGBS

-RGBHV

- Component video (Pr/Y/Pb)

• Component input on 3 RCA

•DVIinput

• VGA input (=analog RGB)

• Communication connections

- RS232/RS422

- Aspect ratio

R5976763 CINEVERSUM 60/70 22042004

Page is loading ...

Cineversum ial-DLP User manual

Brand: Cineversum

Model: ial-DLP

Category: Projectors

Type: User manual

Download PDF

report

Cineversum ial-DLP User manual

Cineversum ial-DLP User manual

Related papers

Other documents