PLUS Vision V-1100Z User manual

POWER

A

U

T

O

M

E

N

U

STATUS

P

O

W

E

R

SOURCE

Q

U

IC

K

M

E

N

U

O

N

O

F

R

E

Z

E

M

U

T

E

P

IP

D

IG

ITA

L

R

G

B

Y

P

b

P

r

V

ID

E

O

S

-V

ID

E

O

Y

C

b

C

r

Q

U

IC

K

E

N

T

E

R

ZO

O

M

V

O

L

V

K

S

T

N

HKSTN

CANCEL

M

ENU

A

S

P

E

C

T

A

U

T

O

P

O

W

E

R

DATA PROJECTOR

V-1100Z

User’s Manual

IMPORTANT

Digital Light Processing, DLP™, Digital Micromirror Device and DMD are all trademarks of Texas

Instruments.

Windows 98, Windows 95, and Windows 3.1 are registered trademarks in the United States and other

countries of Microsoft Corporation.

IBM is a registered trademark of International Business Machines Corporation.

Macintosh and MAC are trademarks of Apple Computer Inc.

Other names of companies and products mentioned are trademarks and registered trade-marks of

the respective companies. ™, ® and © marks are not used in this document.

E-2

IMPORTANT SAFETY INFORMATION

Precautions

Please read this manual carefully before using your PLUS V-1100Z Data Projector and keep

the manual handy for future reference.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED PLUS SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have

sufficient magnitude to cause electric shock. Therefore, it is dangerous to

make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the opera-

tion and maintenance of this unit has been included. Therefore, it should be

read carefully in order to avoid any problems.

The above cautions are given on the bottom of the product.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOIS-

TURE. DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD

OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED. DO

NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL

SERVICING MUST BE DONE BY QUALIFIED PLUS SERVICE PERSONNEL.

WARNING

This is a class A product. In a domestic environment this product may cause radio inter-

ference in which case the user may be required to take adequate measures.

RF Interference

WARNING

The Federal Communications Commission does not allow any modifications or changes

to the unit EXCEPT those specified by PLUS Vision in this manual. Failure to comply with

this government regulation could void your right to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

DOC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

E-3

Important Safeguards

These safety instructions are to ensure the long life of the unit and to prevent fire and shock.

Please read them carefully and heed all warnings.

Installation

• For best results, use the unit in a darkened room.

• Place the unit on a flat, level surface in a dry area away from dust and moisture.

• Do not place the unit in direct sunlight, near heaters or heat radiating appliances.

• Exposure to direct sunlight, smoke or steam can harm internal components.

• Handle the unit carefully. Dropping or jarring can damage internal components.

• Do not place heavy objects on top of the unit.

Power Supply

• The unit is designed to operate on a power supply of 100 - 240 V 50/60 Hz AC. Ensure

that your power supply fits these requirements before attempting to use the unit.

• For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment

and shall be accessible.

• Handle the power cable carefully and avoid excessive bending. A damaged cord can

cause electric shock or fire.

• Disconnect the power cable (mains lead) from the power outlet after using the unit.

Before disconnecting the power cable, make sure that the POWER indicator lights in

amber (not blinking or in green).

Cleaning

• Disconnect the power cable (mains lead) from the unit.

• Clean the cabinet of the unit periodically with a damp cloth. If heavily soiled, use a mild

detergent. Never use strong detergents or solvents such as alcohol or thinner.

• Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the

lens.

• Clean the ventilation slots and speaker grills on the unit periodically using a vacuum

cleaner. If accumulated dust blocks the ventilation slots, the unit will overheat, which may

cause the unit to malfunction.

Use a soft brush attachment when using the vacuum cleaner. Do not use a hard attach-

ment, such as a crevice tool, to prevent the damage to the unit.

Lamp Replacement

• Be sure to replace the lamp when the Status indicator comes on. If you continue to use

the lamp after 1000 hours of usage, the lamp will turn off.

IMPORTANT SAFETY INFORMATION

E-4

Fire and Shock Precautions

• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the

buildup of heat inside the unit. Allow at least 10 cm (3 inches) of space between the unit

and walls.

• Prevent foreign objects such as paper clips and bits of paper from falling into the unit. Do

not attempt to retrieve any objects that fell into the unit. Do not insert any metal objects

such as a wire or screwdriver into the unit. If something should fall into the unit, immedi-

ately disconnect the power cable from the unit and have the object removed by a quali-

fied PLUS service person.

• Do not place any liquids on top of the unit.

• Do not look into the lens while the unit is on. Serious damage to your eyes could

result.

IMPORTANT SAFETY INFORMATION

E-5

Major Features

Book-sized, lightweight (at about 1.1 kg/2.4 lbs) and small high-inten-

sity mobile projector

DMD and the synergistic effects of our own optical design serve to improve the optical utilization

efficiency. The three light sources (RGB) required in color expression are reproduced with one DMD.

These factors have enabled a design that offers both high intensity and small size/lightweight fea-

tures.

Sharp, clear picture

The absence of RGB color infidelity and the inconspicuous gaps between the individual dots permit

the display of small characters and diagrams with distinct clarity. An up-close look reveals the differ-

ence even more.

High contrast ration of 2000:1

Use of a new generation of DMD devices has given birth to an amazing 2000:1 high contrast ratio.

By widening the difference of brightness between black and white, you can see a degree of sharp-

ness that is greater than just the brightness based on specifications.

Beautiful reproduction of high-quality images from DVD

Faithful reproduction of color tones gives rise to the display of natural images. High-quality images

such as those from DVD and other sources bring out the display capabilities that are an essential

strength of the digital projector.

Heightened effectiveness with picture in picture

The video image is projected as a sub-picture within the personal computer picture. This expands the

usefulness of the projector even more.

Digital technology corrects the horizontal and vertical keystone dis-

tortion of the projected picture

New technology is used to correct the horizontal keystone distortion in addition to the regular key-

stone correction. This permits even simpler setup adjustments.

Connection permitted for personal computers equipped with DVI con-

nectors

Inclusion of a DVI connector allows the input of analog RGB signals as well as digital RGB signals.

(The supplied conversion cable supports personal computers having a regular analog RGB connec-

tor. See the Table of Supported Frequencies on Page 70 for information about display resolution.)

E-6

Table of Contents

Preparation and Background Knowledge

IMPORTANT SAFETY INFORMATION ............................................................................ E-2

Major Features ................................................................................................................. E-5

Table of Contents ............................................................................................................. E-6

Checking the Supplied Accessories .............................................................................. E-8

Names of the Main Unit Parts ....................................................................................... E-10

Names of the Remote Control Parts ............................................................................ E-12

Preparing the Remote Control...................................................................................... E-13

Button Battery Replacement ..................................................................................... E-13

Remote Control Range ............................................................................................. E-14

Setup and Projection

The Procedure Up to Projecting to the Screen ........................................................... E-15

Placement Guide

Screen Size and Projection Distance ........................................................................ E-16

Connecting Personal Computers and Video Equipment

Connections with PC Connectors

Personal Computers with a DVI Connector ......................................................... E-18

Personal Computers with a Mini D-Sub 15-Pin Connector ................................. E-19

To Output the External Output Signal of a Notebook Computer ......................... E-20

Connections with Video Connectors

Video Equipment with VIDEO Connectors .......................................................... E-21

Video Equipment with S-VIDEO Connectors ...................................................... E-21

Connections with Component Signals

When the Video Connectors are Y, Cb, and Cr Connectors ................................ E-22

When the Video Connectors are Y, Pb, and Pr Connectors ................................ E-22

Connections with Audio Connectors ......................................................................... E-23

Power Cable Connections and Switching the Power On/Off

Operating ................................................................................................................... E-24

Finishing .................................................................................................................... E-25

Adjustment of the Projection Screen

Projection Screen Position Adjustment ..................................................................... E-26

Making Adjustments with the Adjusters .............................................................. E-27

Focus Adjustment ...................................................................................................... E-27

General Operation

Input Selection ............................................................................................................... E-28

Automatic Adjustment of Analog RGB ........................................................................ E-29

Selection of Aspect Ratio ............................................................................................. E-30

Projecting a Sub-Picture ............................................................................................... E-31

Freezing a Moving Picture ............................................................................................ E-31

Cancelling Video and Audio Temporarily ..................................................................... E-31

Using the Quick Menu ................................................................................................... E-32

Correcting Keystone Distortion of the Projection Screen ......................................... E-34

Enlargement of the Image and Video Movement ........................................................ E-35

Adjustment of the Volume ............................................................................................. E-36

E-7

Menu Operations

Menu Operation Method ................................................................................................ E-37

Names and Functions of the Parts ............................................................................ E-37

Names and Functions of the Remote Control Buttons that Operate Via a Menu ...... E-37

Names and Functions of the Main Unit Buttons Used in Menu Operation ................ E-38

Names and Functions of Menu Screen Parts ............................................................ E-38

Performing Menu Operations .................................................................................... E-39

Selecting Another Menu Name with Remote Control Operation ............................... E-43

List of Item Names Offering Input Selection and Adjustments/Settings .................... E-44

Adjustments and Settings

Picture

Brightness / Contrast / Color / Tint / Sharpness ........................................................ E-46

Picture Adjustment / Fine Picture / H Position / V Position ........................................ E-47

Reset ......................................................................................................................... E-48

Color

Quick Color Adj. ........................................................................................................ E-49

Gamma ..................................................................................................................... E-49

Color Temp. ............................................................................................................... E-49

White ......................................................................................................................... E-50

Color System ............................................................................................................. E-50

Color Space .............................................................................................................. E-50

View

Aspect ....................................................................................................................... E-51

Filter .......................................................................................................................... E-52

Projection .................................................................................................................. E-52

Keystone .................................................................................................................... E-53

Picture in Picture ....................................................................................................... E-54

Setup

Language .................................................................................................................. E-55

Auto Source............................................................................................................... E-55

Auto Power Off .......................................................................................................... E-56

On Screen ................................................................................................................. E-56

Menu Position ............................................................................................................ E-57

YPbPr ........................................................................................................................ E-57

Background ............................................................................................................... E-57

White Balance ........................................................................................................... E-58

Info.

Status ........................................................................................................................ E-59

Factory Default .......................................................................................................... E-59

Lamp Timer Reset ..................................................................................................... E-59

Resolution / Frequency ............................................................................................. E-60

Lamp Timer ............................................................................................................... E-60

Miscellaneous

When the STATUS Indicator is Lit/Flashes .................................................................. E-61

Troubleshooting ............................................................................................................. E-63

Cleaning ......................................................................................................................... E-65

Replacing the Lamp Cartridge ..................................................................................... E-66

Specifications ................................................................................................................ E-69

Table of Supported Frequencies .................................................................................. E-70

Cabinet Dimensions ...................................................................................................... E-71

Table of Contents

E-8

Checking the Supplied Accessories

Remove the main unit and the accessories from the box and check that the following items are included.

ON

OFF

FREEZE

MUTE

PIP

DIGITAL

RGB

YPbPr

VIDEO

S-VIDEO

YCbCr

QUICK

ENTER

ZOOM

VOL

V

K

S

T

N

HKSTN

CANCEL

M

EN

U

ASPECT

AUTO

POWER

Remote control

(includes one button battery) [1]

This controls the projector. Please remove the transportation

insulation sheet at time of purchase. (See Page E-13.)

Power cable (1.8 m / 5.9 feet) [1]

This power cable supplies power to the unit. See Page E-24

about connections.

DVI / Mini D-sub 15-pin conversion cable

(19 cm / 0.6 feet) [1]

This is used when the monitor connector of the personal com-

puter is a mini D-sub 15-pin connector. See Page E-19, 22

about connections.

No. 772708000

RGB signal cable

(Mini D-sub 15-pin, 2 m / 6.6 feet) [1]

This is used when the monitor connector of the personal com-

puter is a mini D-sub 15-pin connector. See Pages E-19 about

connections.

No. 772709000

S-Video cable (3.5 mm diameter plug / Mini DIN

4-pin plug, 1.5 m / 4.9 feet) [1]

This cable is used in the connection of video equipment that

has an S-video connector. Connections are described on Page

E-21.

No. 772705000

Video cable (3.5 mm diameter plug / RCA pin

plug, 1.5 m / 4.9 feet) [1]

This cable is used in the connection of video equipment that

has an RCA jack type video connector. Connections are de-

scribed on Page E-21.

No. 772704000

E-9

Checking the Supplied Accessories

Audio cable (2.5 mm diameter plug / RCA pin

plug, 1.5 m / 4.9 feet) [1]

This cable is used with equipment that has phono type audio

jacks. Connections are described on Page E-23.

No. 772706000

Soft case (for projector and accessories) [1]

This case is used when storing the projector. The case is made

up of two portions that are joined by hook-and-loop tape to

form a single item. The case can be separated into two pieces.

Projector

Accessories

User's Manual (CD-ROM edition) [1]

User's Manual (Simplified Edition) [1]

Precautions

* Leave the power cable plugged in (for 5 to 10 minutes) until the projector returns to room

temperature before placing the projector inside the soft case. Placing the projector into the

case soon after switching off the power could cause the projector to break down.

* Be sure to attach the lens cap and place the projector into the soft case with the lens facing

upward.

E-10

Names of the Main Unit Parts

POWER

AUTO

MENU

STATUS

POWER

SOURCE

QUICK

MENU

AUDIO

VIDEO

POWER

A

UTO

M

EN

U

STATUS

P

O

W

ER

SOURCE

Q

UICK

M

E

N

U

Exhaust

vents

Precautions

The ventilation slots discharge the heat of the lamp and care must be taken not to come into

contact with them.

STATUS indicator [E-61]

POWER button [E-24]

SOURCE button [E-28]

POWER indicator [E-24]

MENU button [E-38]

AUTO button [E-28]

QUICK MENU button [E-32]

Remote control

sensor [E-14]

Front adjuster button [E-27]

(There is also one on the left side.)

Speaker

Exhaust

vents

Remote control

sensor

Lens

Focus ring [E-27]

Lens cap

To protect the lens, attach the lens

cap when the projector is not in use.

Ventilation

slots

Zoom ring [E-26]

E-11

Names of the Main Unit Parts

AUT

O

S

OURCE

QUICK

MENU

PC

AUDIO

VIDEO

POWER

AUTO

MENU

STATUS

POWER

S

O

U

R

C

E

QUICK

MENU

PC

AUDIO

VIDEO

Front adjusters [E-27]

Built-in Security Slot

This security slot supports the MicroSaver Security System manufactured by

Kensington Microware Inc.

AUDIO jack [E-23]

VIDEO jack [E-21, 22]

PC connector [E-18,19, 22]

Built-in security slot

(See description below.)

Ventilation slots

AC IN connector [E-24]

Rear adjuster [E-27]

Ventilation slots

Lamp cover [E-67]

E-12

+/– button

(Used in all adjustments)

Names of the Remote Control Parts

ON

OFF

FREEZE

MUTE

PIP

DIGITAL

RGB

YPbPr

VIDEO

S-VIDEO

YCbCr

QUICK

ENTER

ZOOM

VKSTN

HKSTN

CANCEL

MENU

ASPECT

AUTO

POWER

Infrared transmitter [E-14]

ON OFF

FREEZE MUTE PIP

DIGITAL RGB YPbPr

VIDEO S-VIDEO YCbCr

QUICK

ENTER

ZOOM

CANCEL

MENU

ASPECT AUTO

POWER

HKSTN

VKSTN

VOL

F

REEZE button [E-31]

(Freezes moving pictures)

MUTE button [E-31]

(Temporarily cancels the

video and audio)

QUICK button [E-32]

(Displays a simplified menu)

ASPECT button [E-30]

(Selects the vertical and hori-

zontal ratio of the screen)

HKSTN button [E-34]

(Horizontal keystone distortion

correction display)

ZOOM button [E-35]

(Digital zoom adjustment display)

PIP button [E-31]

(Displays the picture associated

with the VIDEO connector as a

smaller picture within the display

screen associated with the PC

connector)

Buttons used for input selec-

tion [E-28]

DIGITAL button, RGB button,

YPbPr button, VIDEO button, S-

VIDEO button, and YCbCr but-

ton

AUTO button [E-29]

(Automatic adjustment of the

analog RGB moving image)

Buttons used for menu opera-

tions [E-37]

VKSTN button [E-34]

(Vertical keystone distortion cor-

rection display)

VOL button [E-36]

(Volume adjustment display)

Precautions

Handling of the Remote Control

* Do not drop the remote control or handle it inappropriately.

* Do not expose the remote control to water or other liquids. Should the remote control become

wet, wipe it dry immediately.

* Try to avoid use in hot and/or humid locations.

* Please keep button batteries out of the reach of children. If a battery is swallowed, promptly

obtain the medical care of a doctor.

* Remove the batteries from the remote control when it is not going to be used for a long period.

* Some operations (such as menu operations) are available only through the use of the remote

control and attention should be given to its careful handling.

POWER button [E-24]

E-13

Preparing the Remote Control

Button Battery Replacement

Using the remote control for the first time

The battery compartment is fitted with a transportation insulation sheet at

the time of shipping. Pull out the sheet and remove it. The remote control is

now ready for use.

Replacement Method

1

Insert the tip of a ballpoint pen or some other pointed object into the hole of the

battery holder, then pull out to open.

2

Remove the old battery and install a new button battery with (+) side facing up-

ward in the battery holder.

Purchase a CR2025 type battery for replacement.

3

Insert the battery holder into the remote control and push in until the battery holder

closes with a "click" sound.

CR2025

M

n

O

2

-

L

i

C

E

L

3

V

O

L

T

S

J

A

P

A

N

H

C

R2025

CR2025

M

n

O

2

-

L

i

C

E

L

3

V

O

L

T

S

J

A

P

A

N

H

C

R

20

25

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type (CR2025) recommended by the manufacturer.

Dispose of used batteries according to your local regulations.

E-14

Remote Control Range

Point the infrared transmitter of the remote control toward the remote control sensor located at the front

or rear of the main unit and operate.

Reception of the remote control signal should generally be possible within the range illustrated below.

30°

50°

4m / 13.1 feet

7m / 23 feet

Remote control sensor

Remote control infrared

transmitter

Side View

Remote control

sensor

Remote control infrared

transmitter

Top View

Note

* Exposure of the main unit's remote control sensor or the remote control infrared transmitter to bright light or

the obstruction of the signal by an obstacle located in the pathway may prevent operation.

* The remote control will not function when the battery is exhausted.

Preparing the Remote Control

E-15

The Procedure Up to Projecting to the Screen

Perform setup adjustments in the following order.

1

Position the projector

See "Projection Distance and Screen Size" on Pages E-16 and E-17.

Determine the locations to set up the screen and the projector.

2

Connect the video equipment and personal computer

Connect your equipment to the projector.

When the personal computer has a DVI connector or a mini D-sub 15-pin connector

See "Connections with PC Connectors" on Page E-18.

When the video equipment has a video connector or an S-video connector

See "Connections with Mini D-Sub 15-Pin Connectors" on Page E-19.

When the video equipment has a YCbCr connector or a YPbPr connector

See "Connections with Component Signals" on Page E-22.

When playing the audio through the built-in speaker of the projector

See "Connections with the AUDIO Jack" on Page E-23.

3

Connecting the power cable and switching on the power

See "Operating" on Page E-24.

See "Finishing" on Page E-25.

4

Switching on the power of the personal computer and video equipment

5

Properly adjust the projection image to the screen

See "Projection Screen Position Adjustment" on Page E-26.

6

Focusing

See "Focus Adjustment" on Page E-27.

7

Selecting input equipment

See "Input Selection" on Page E-28.

8

Adjust the screen or video image

Adjust the image to the optimum condition as required.

See the Table of Contents (Adjustments and Settings) for the adjustment items.

About DLP projectors

Though careful attention is paid to providing optimum quality, please note that with DLP type projec-

tors, in rare cases there may be black spots or bright spots among the picture elements.

Note

* Please purchase a screen.

* A DVI-D cable (order code 28-697), which is available separately, is required for connections with the DVI

connector of the personal computer.

* A component cable (order code 28-698), which is available separately, is required to connect a DVD player or

other equipment with YCbCr connectors.

* A component cable (order code 28-690), which is available separately, is required to connect high definition

(HD) video equipment or other equipment with YPbPr connectors.

E-16

26"

40"

60"

80"

100"

120"

150"

180"

200"

1.20 (3.94)

1.54–1.85

(5.05–6.07)

2.33–2.80

(7.64–9.19)

3.12–3.75 (10.24 –12.30)

3.91–4.70 (12.83 –15.42)

4.70–5.64 (15.42 –18.50)

5.89–7.07 (19.32 –23.20)

7.04–8.45 (23.10 –27.72)

7.86–9.44 (25.79

–30.97)

h1

h2

P

O

W

E

R

AUTO

MENU

S

T

A

T

U

S

POWER

S

O

U

R

C

E

QUICK

MENU

PC

A

UDIO

V

IDEO

Placement Guide

● Use this information as a guide to find out about the screen size when the projector is placed at a

certain location, or to find out the approximate size of a screen that will be required.

● The projection distance over which focussing is adjustable is 1.20 m (3.9 feet) to 9.44 m (30.97 feet).

The projector should be placed within this range.

Screen Size and Projection Distance

Height from center

of lens to bottom

edge of the projec-

tion

Height from center of

lens to top edge of the

projection

Unit: m (feet)

Lens surface of

the main unit

Screen Size Designation (Inches)

E-17

Placement Guide

* There is a tolerance of ±5% due to design values.

* This table uses the lens apex and lens center as references and requires that the projec-

tor be in a horizontal condition (with front and rear adjusters fully withdrawn).

26"

40"

60"

80"

100"

120"

150"

180"

200"

0.53  0.40

0.81  0.61

1.22  0.91

1.63  1.22

2.03  1.52

2.44  1.83

3.05  2.29

3.66  2.74

4.06  3.05

—–1.20

1.54 – 1.85

2.33 – 2.80

3.12 – 3.75

3.91 – 4.70

4.70 – 5.64

5.89 – 7.07

7.04 – 8.45

7.86 – 9.44

0.47

0.72

1.07

1.43

1.79

2.14

2.68

3.21

3.57

0.07

0.11

0.16

0.21

0.26

0.31

0.39

0.47

0.52

Screen Size

Designation (Inches)

Screen Size Width x Height Projection Distance Height h1 Height h2

1.74  1.31

2.66  2.00

4.00  2.99

5.35  4.00

6.66  4.99

8.00  6.00

10.00  7.51

12.00  8.99

13.32  10.00

(m) (feet)

—–3.94

5.05 – 6.07

7.64 – 9.19

10.24 – 12.30

12.83 – 15.42

15.42 – 18.50

19.32 – 23.20

23.10 – 27.72

25.79 – 30.97

1.54

2.36

3.51

4.69

5.87

7.02

8.79

10.53

11.71

0.23

0.36

0.52

0.69

0.85

1.02

1.28

1.54

1.71

(m) (feet) (m) (feet) (m) (feet)

Wide – Tele Wide – Tele

Screen size (Diagonal) Height

Width

E-18

Connecting Personal Computers and Video Equipment

● Connecting this unit with a personal computer permits presentation data to be projected as a large

screen display at conferences, lectures, and on other occasions. Furthermore, connecting this unit to

a DVD player or other video equipment source in combination with an audio/video amplifier and speaker

system will allow you to enjoy convincing home theater.

Connections with PC Connectors

Please check the following matters before making connections to the

personal computer.

* Suitable resolution is 1024768 dots (XGA), and the displayable resolution is S-XGA (12801024

dots).

Note that input of a resolution that exceeds the displayable resolution will cease to be projected and

should this be the case, you will need to change the resolution to a displayable resolution at the

computer side. Check with "Table of Supported Frequencies" on Page E-70.

* The setting method of the personal computer will differ depending on the personal computer that you

are using. For information, read the instruction manual for your personal computer, read the on-line

help, or contact the manufacturer of your personal computer.

Personal Computers with a DVI Connector

* Make the connection with a DVI-D cable and the PC connector of the projector.

When connecting, arrange the connectors in the proper orientation and plug in. Turn the screw knobs

and fasten to the connector of the main unit.

* Switch the input selection of the projector to "Digital RGB".

PC

VIDEO

AUDIO

Monitor output

Personal

computer

DVI-D cable (Available as an option. Order code: 28-697)

Note

This projector uses a 29-pin DVI connector that supports the digital interface. Digital signal TMDS (Transition

Minimized Differential Signalling) of the DVI (Digital Visual Interface) standard is used.

E-19

Connecting Personal Computers and Video Equipment

Personal Computers with a Mini D-Sub 15-Pin Connector

* Make the connection to the projector's PC connector and the mini D-sub 15-pin connector through the

use of a DVI/mini D-sub 15-pin conversion cable.

* When connecting, arrange the connectors in the proper orientation and plug in. Turn the screw knobs

and fasten to the connector of the main unit.

* Switch the input selection of the projector to "Analog RGB".

PC

VIDEO

AUDIO

Personal computer

Monitor output

DVI/mini D-sub 15-pin conversion

cable (Supplied item)

RGB signal cable (Supplied item)

Note

* Before making connections, check the power of the projector and the equipment to be connected is switched

off.

* When projection will be with a notebook computer connected, knowledge will be required for the cable connec-

tion and notebook computer startup procedure as well as the operation that follows startup. Please consult the

instruction manual of your notebook computer or the on-line help.

E-20

Connecting Personal Computers and Video Equipment

To Output the External Output Signal of a Notebook Computer

When projection will be with a notebook computer connected, knowledge will be required for the cable

connection and notebook computer startup procedure as well as the operation that follows notebook

startup. Please consult the instruction manual of your notebook computer or the on-line help while per-

forming the following procedure.

1

Check whether a signal is being sent from the notebook computer to the projector.

An indication appearing on the liquid crystal display of the notebook computer does not necessarily

mean that an external output signal is being output.

2

Should a sign not be output from the notebook computer, please try the operation described below.

For an IBM PC/AT, DOS/V computer, press the [Fn] key plus any one of the [F1] to [F12] keys. (See

the table below.)

Note

When the liquid crystal display of the notebook computer and the projector are displayed at the same time, the

projected image might not be correct even though the liquid crystal display shows a correct indication. Should

this occur, stop the simultaneous display of the notebook computer and try the mode with external output only.

(Try an operation such as that described in aforementioned Step 2 and try closing the liquid crystal panel which

might result in external output only.)

Manufacturer Model Key

akia All computers Fn + F2

COMPAQ All computers Fn + F4

DELL All computers Fn + F8

EPSON All computers Fn + F8

FUJITSU All computers Fn + F10

GATEWAY All computers Fn + F3

iiyama All computers Fn + F3

IBM All computers Fn + F7

NEC All computers Fn + F3

Panasonic All computers Fn + F3

SHARP All computers Fn + F5

SONY All computers Fn + F7

SOTEC All computers Fn + F3

TOSHIBA All computers Fn + F5

Victor All computers Fn + F10

Note: Table information is current to September 2002.

Page is loading ...

PLUS Vision V-1100Z User manual

This manual is also suitable for

PLUS Vision V-1100Z User manual

Related papers

Other documents