Lamp Kit
Installation Manual
iCon H600
R9841828
R9841829
R5976827/03
01/09/2008
Barco nv Presentations
Noordlaan 5, 8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.35.86.51
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied w ar-
ranties or m erchantability and fitness for a particular purpose. Barco m ay m ake improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This pub lication could contain technical inaccuracies or typographical errors. Changes are periodically m ade to the information in this
publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not other
wise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Federal Communications Commis sion (FCC Statement)
This equipment h as been tested and found to c omply w ith the limits for a class A digital device, pursuan t to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection aga inst harm ful interference when the equipment is operated in a com m ercial
environment. T his equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. O peration of this equipment in a residential area may
cause harm ful interference, in which case the user will b e responsible for correcting any interference at his own expense
Guaran tee and Compensation
Barco provides a guarantee relating to perfect man ufacturing as part of the legally stipulated terms of guarantee. O n receipt, the pu rchaser
must immediately inspect all delivered goods for dam age incurred during transport, as well as for material and manufacturing faults Barc o
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of c omm issioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Bar co can r epair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or c ancellation of the contract. All other claims, in particular those relating to compensa tion for direct or
indirect damage, and also damage attributed to the operation of s oftware as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the dam age is n ot pro ven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or p art of Barco.
If the pur chaser or a third party carries out modifications
or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if t he systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are s ubject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be r endered invalid. Not included in the guarantee coverage are
system failures which are attributed to programs or s
pecial electronic c ircuitry provided by the pur chaser, e.g. interfaces. Nor mal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and m aintenance regulations specified in the this manual m ust be complied with by
the customer.
Trademarks
Brand and product names m entioned in this manual m ay be trademarks, registered tradem arks or copyrights of their respective holders.
All brand and product n ames me ntioned in this manual serve as com men ts or examples and are not to be understood as advertising for
the products or their manufactures.
Table of contents
TABLE OF CON TENTS
1. Safety................................................................................................................. 3
1.1 Safety Guidelines..................................................................................................................... 3
1.2 Recycling guidelines.................................................................................................................. 3
2. Kit description ...................................................................................................... 5
2.1 Kit content ............................................................................................................................ 5
3. Lamp replacement ................................................................................................. 7
3.1 Reset lamp Runtime.................................................................................................................. 7
3.2 Removing the rear cover ............................................................................................................ 8
3.3 Lamp removal......................................................................................................................... 8
3.4 Lamp m ounting ......................................................................................................................10
Index......................................................................................................................13
R5976827 LAMP KIT 01/09/2008 1
Table of contents
2 R5976827 LAMP KIT 01/09/2008
1. Safety
1. SAFETY
1.1 Safety Guidelines
This procedure is intended for use only by qualified service technicians w ho have been trained and au thorized
by BAR CO !
WARNING: Hot Surface an d Risk o f Explosion:Switch the projector to stand by an d let it cool do wn for at least
15 minutes . These lamps con sist of a quartz arc tube o perating at very high temperature and high pressure
which m ay explode suddenly. There is a risk of personal injury and property damage from hot quartz arc tube
particles if handled incorrectly.
WARNING: Risk of Electrical Shock: Power down the projector and unplug the power cord from the wall
outlet. Once the projector is cooled down and the power is off, continue with the procedure.
WARNING: Lamp Runtime Warning: Do n ot exceed the indicated maximum t otal lifetime of the lamp for sa fe
operation in normal power mode. Do not use it longer ! Always replace the lamp with the BARCO lamp kit.
WARNING: UV Radiation Exposure : Nev er light the lamp if the rear cover (lamp cover) of the projector is
removed, unless you wear UV radiation eye and skin protection.
1.2 Recycling guidelines
WARNING: Do not b reak or crush lamps because thi
s may pose health a nd environmental risks when mercury
vapors are released.
CAUTION: To avoid breaking the lamp s, repack carefully w h en storing and transporting them.
CAUTION: Lamps may not be disposed as normal household trash.
Contact yo ur local waste disposal facility for information on the rec ycling p rog ram for HID (High Intensity
Discharge ) lamps in y our area.
Image 1-1
R5976827 LAMP KIT 01/09/2008 3
1. Safety
Disposal options for mercury-containing lamps
• Recycle th rough a municipal or solid waste district household hazardous waste collection program in accordance with local
regulations.
• Direct shipm ent to lamp recycler
• Shipment through a hazardous waste transporter
4
R5976827 LAMP KIT 01/09/2008
2. Kit description
2. KIT DESCRIPTION
Kit information
This lamp kit is to be installed on the following Barco projectors:
• iCon H600: contains 2 lamps
Image 2-1
Lamp
2.1 Kit content
Two kits are available: a kit with one lamp and a kit including two lamps. E ach of the kits has a different o rder
number.
Kit overview
Kit number Description
Quantity of lamps
Manual
R9841828 300 W UHP lamp kit 1 R5976827
R9841829 300 W UHP lamp kit 2 R5976827
R5976827 LAMP KIT 01/09/2008 5
2. Kit description
6 R5976827 LAMP KIT 01/09/2008
3. Lamp replacement
3. LAMP REPLACEMENT
Overview
• Reset lamp Runtime
• Removing the rear cover
• Lamp removal
• Lamp mounting
The images in this procedure can sligh tly differ from y our pro jector. However this does not influe nce the
procedures de scribed below!
3.1 Reset lamp Runtime
When to reset the lamp runtime ?
Reset the lamp runtime whene ver you replace a lamp
WARNING: Lam p runtime reset as well as the lamp replacement can only be d one by a Barco authorized
technician.
How to reset the lamp runtime ?
1. Press ME NU to activate the Toolbar
2. Press → to select the Lamp item
3. Press ↓ to P ull down the Lamp m enu
4. Use ↑ or ↓ to select Reset runtime
5. Press → to pull down the menu
6. Use ↑ or ↓ to select the lamp to be r eset
Image 3-1
7. Press ENTER
A dialogbox is displayed
R5976827 LAMP KIT 01/09/2008
7
3. Lamp replacement
Image 3-2
8. Use ←or →, the numeric keys on the remote, or the keypad to enter the serial num ber of the new lam p (s erial number 0000000
will no t b e accepted).
3.2 Removing the rear cover
Necessary tools
cross headed screwdriver.
How to remove the rear cover ?
1. Loosen and remove the 2 screws as indicated.
Image 3-3
2. Remove the rear cover
3.3 Lamp removal
How t o remov e the lamp
1. Unplug the lamp connector
8
R5976827 LAMP KIT 01/09/2008
3. Lamp replacement
Image 3-4
2. Loosen the 4 screws as indicated and remove the lamp cover plate
Image 3-5
3. Pull up the lamp locking plate
Image 3-6
The lamp is now unlocked
4. Take out the lamp as shown on the image
R5976827 LAMP KIT 01/09/2008
9
3. Lamp replacement
Image 3-7
1 slide the lam p sidewards
2 take out the lamp (upwards)
3.4 Lamp mount ing
How to mount the lamp
1. Place the lamp in its ho using
2. Firmly push the lamp at the bottom side until you hear a “click” sound that signals the right lamp position (lamp locked into the
projector frame)
Image 3-8
3. While firmly pushing the t op side of the lamp, push the lamp lock plate d ownwards (the 2 lips r emaining at about 2 m m o f the top
plate)
10
R5976827 LAMP KIT 01/09/2008
3. Lamp replacement
Image 3-9
4. Place the lamp cover plate and tighten the 4 s crews
5. Plug in the lamp connec tor
6. Mount the rear cover
R5976827 LAMP KIT 01/09/2008
11
3. Lamp replacement
12 R5976827 LAMP KIT 01/09/2008
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Barco iCon H600 lamp kit (300W UHP) Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco 2 kW Xenon lamp SIM 10 Quick start guide
-
Barco iQ Pro R500 Owner's manual
-
-
Barco iCon H600 Installation guide
-
-
Barco Galaxy NW-12 EX Installation guide
-
Barco Galaxy NW-7 EX Installation guide
-
Barco iD H500 User manual
-
Barco R9841760 User manual
-