Cineversum BlackWing One MK2019 User manual

Cineversum
Brand
Cineversum
Model
BlackWing One MK2019
Category
Data projectors
Type
User manual

This manual is also suitable for

R599900
User manual
v1.1
Changes
Cineversum provides this manual ‘as is’ without warranty of any kind, either expressed or implied, including but
not limited to the implied warranties or merchantability and tness for a particular purpose. Cineversum may
make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any
time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to
the information in this publication; these changes are incorporated in new editions of this publication.
Copyright
All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Cineversum.
Guarantee
Cineversum provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults. Cineversum must be informed immediately in
writing of any complaints. If the purchaser or third party caries out modications or repairs on goods delivered
by Cineversum, or if the goods are handle incorrectly, in particular if the systems are commissioned operated
incorrectly or if, after the transfer of risks, the goods are subject to inuences not agreed upon in the contract, all
guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system
failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces.
Normal wear as well as normal maintenance are not subject to the guarantee provided by Cineversum either.
The environmental conditions as well as the servicing and maintenance regulations specied in this manual must
be complied with by the customer.
Trademarks
Brands and product names mentioned in this manual may be trademarks, registered trademarks or copyrights
of their respective holders. All brands and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products of their manufactures.
R599900 - Blackwing Series User Manual 3
TABLE OF CONTENTS
1.0  SAFETYINSTRUCTIONS ..................................................................................................5
1.1 Important Information ....................................................................................................................5
1.2 Regional Specic Information........................................................................................................5
1.3 Important Safeguards .....................................................................................................................5
1.4 Image projector classication .........................................................................................................7
2.0  INSTALLATIONGUIDELINES .......................................................................................7
2.1 Introduction ....................................................................................................................................7
2.2 THX 4K Display Certication (Blackwing Elite model only) ..................................................... 8
2.3 Environment of Use........................................................................................................................8
2.4 Air-Flow and Space Requirements ................................................................................................. 8
2.5 Installing the projection screen.......................................................................................................9
2.6 When to use the High Altitude mode .............................................................................................9
2.7 Ceiling Mounting the Unit .............................................................................................................9
2.8 Projection Distance.......................................................................................................................10
2.9 Setting the Lens and using Lens Memories..................................................................................10
3.0  REMOTECONTROLUNIT(RCU) .............................................................................. 12
4.0  GETTINGSTARTED ......................................................................................................... 13
4.1 General View ................................................................................................................................13
4.2 Connecting the Power Cord .........................................................................................................13
4.3 Operating and Navigation Buttons ...............................................................................................14
5.0  CONNECTIONS ................................................................................................................... 14
5.1 Caution when connecting a Device to HDMI Input ..................................................................... 14
5.2 Connecting a Video Source to the Projector.................................................................................15
5.3 Connecting an Automation or Control device .............................................................................. 15
6.0  FIRSTSTARTUP ................................................................................................................ 16
6.1 Turn the power ON ....................................................................................................................... 16
6.2 Turn the Power O .......................................................................................................................16
7.0  MENUSTRUCTURE .......................................................................................................... 17
8.0  PICTUREADJUST ............................................................................................................. 20
8.1 Picture Modes and Color Proles .................................................................................................20
8.2 Advanced Picture Mode ...............................................................................................................20
8.3 Advanced Color Prole ................................................................................................................21
8.4 Color Temperature ........................................................................................................................ 21
8.5 Advanced Color Temperature .......................................................................................................22
8.6 Gamma .........................................................................................................................................22
8.7 Advanced Gamma ........................................................................................................................22
8.8 Multiple Pixel Control Level (MPC Level) .................................................................................23
8.9 Motion Control .............................................................................................................................23
8.10 Contrast ........................................................................................................................................23
8.11 Brightness ..................................................................................................................................... 23
8.12 Color .............................................................................................................................................24
8.13 Tint ...............................................................................................................................................24
9.0  4KINPUTS ............................................................................................................................. 24
9.1 Choosing the correct Input level ..................................................................................................24
9.2 High Dynamic Range sources ......................................................................................................24
9.3 4K contents and their Color Proles ............................................................................................25
10.0  INPUTSIGNAL .................................................................................................................... 26
10.1 Input Level ...................................................................................................................................26
10.2 Color Space ..................................................................................................................................26
10.3 HDR Setting .................................................................................................................................26
10.4 HDMI2 EDID ............................................................................................................................... 26
11.0  3DCONTENTAND3DPROJECTION ....................................................................... 27
R599900 - Blackwing Series User Manual
4
11.1 General Information about 3D playback ......................................................................................27
11.2 3D Settings ...................................................................................................................................27
11.3 Operating the 3D Glasses .............................................................................................................28
12.0  INSTALLATION .................................................................................................................. 29
12.1 Installation Modes ........................................................................................................................29
12.2 Lens Control .................................................................................................................................29
12.3 Pixel Adjust ..................................................................................................................................29
12.4 Mask .............................................................................................................................................30
12.5 Anamorphic ..................................................................................................................................30
12.6 Screen Adjust and Screen No. ......................................................................................................31
12.7 Installation Style ........................................................................................................................... 31
12.8 Keystone .......................................................................................................................................31
12.9 Pincushion ....................................................................................................................................31
12.10 Aspect ...........................................................................................................................................31
13.0  DISPLAYSETUP ................................................................................................................. 32
14.0  FUNCTION ............................................................................................................................ 32
14.1 Trigger ..........................................................................................................................................32
14.2 O-Timer ......................................................................................................................................32
14.3 ECO Mode .................................................................................................................................... 32
14.4 Network ........................................................................................................................................32
14.5 Remote Code A or B .....................................................................................................................32
14.6 High Altitude Mode ...................................................................................................................... 33
14.7 Lamp Reset ................................................................................................................................... 33
14.8 Factory Reset ................................................................................................................................33
14.9 Software Update ...........................................................................................................................33
15.0  INFORMATIONMENU .................................................................................................... 33
16.0  CINEMASCOPESETUPS ................................................................................................ 34
16.1 Cinemascope setup with Lens Zoom............................................................................................34
16.2 Installing a 2.35:1 screen with the Static Cinemascope kit ..........................................................34
17.0  MAINTENANCE .................................................................................................................. 35
17.1 Cleaning and Replacing the Dust Filter .......................................................................................35
17.2 Dirt on the Lens ............................................................................................................................36
17.3 Replacing the Lamp......................................................................................................................36
17.4 Blinking LEDs and Troubleshooting ............................................................................................38
18.0  MISCELLANEOUS ............................................................................................................. 39
18.1 RS-232C protocol ......................................................................................................................... 39
18.2 LAN protocol ...............................................................................................................................41
18.3 Infra Red, long hex-pronto compatible RCU ...............................................................................42
18.4 Specications................................................................................................................................43
18.5 Dimensions ...................................................................................................................................44
SAFETY INSTRUCTIONS
R599900 - Blackwing Series User Manual 5
1.0  SAFETY INSTRUCTIONS
1.1  Important Information
Lead-free regulation
This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains
lead in some components. Disposal of these materials may be regulated in your community due to environmental
considerations. For disposal or recycling information please contact your local authorities, or the Electronics
Industries Alliance: http://www.eiae.org. Call 1-800-252-5722(For USA) or 1-800-964-2650(For Canada)
Information for Users on Disposal of Old Equipment
This symbol indicates that the electrical and electronic equipment should not be disposed as general
household waste at its end of life. Instead, the product should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment for proper treatment, recovery
and recycling in accordance with your national legislation.
For more information about collection point and recycling of this product, please contact your local
municipal ofce, your household waste disposal service or the shop where you purchased the product. Penalties
may be applicable for incorrect disposal of this waste, in accordance with national legislation.
1.2  RegionalSpecicInformation
CE mark and Directive 2011/65/EU - ROHS 2 (Europe only) In accordance with Article 7 and the
adoption into national law by 2nd January 2013, this product has been designed and manufactured in accordance
with Article 4. The technical documentation and the written declaration of conformity that assesses the product
conformity can be provided to the competent National Authority upon an email request to: [email protected]
Other Countries outside the European Union:
If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules
in your country for the treatment of old electrical and electronic equipment.
FCC Information (USA only)
Changes or modication not approved by Cineversum could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
CAN ICES-3 (A) / NMB-3 (A)
To reduce the risk of electric shock, do not remove cover. Refer servicing to qualied service personnel.
This projector is equipped with a 3-blade grounding type plug to satisfy FCC rule.
If you are unable to insert the plug into the outlet, contact your electrician.
1.3  Important Safeguards
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to
assure your personal safety. IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules
for its installation, use and service.
The power input is auto-ranging from 100 to 240 VAC.
Do not install the projector in a place that cannot support its weight securely. If the installation place is not sturdy
enough, the projector could fall or overturn, possibly causing personal injury.
R599900 - Blackwing Series User Manual
SAFETY INSTRUCTIONS
6
Please read these Important Safeguards carefully before use.
• All the safety and operating instructions should be read before the product is operated.
• All warnings on the product and in the operating instructions should be adhered to.
• All operating instructions should be followed.
• Place the projector near a wall outlet where the plug can be easily unplugged.
• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
• Do not use attachments not recommended by the product manufacturer as they may be hazardous.
• Do not use this product near water. Do not use immediately after moving from a low temperature to high
temperature, as this causes condensation, which may result in re, electric shock, or other hazards.
• Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. The product should be mounted according to the
manufacturer’s instructions, and should use a mount recommended by the manufacturer.
• When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and uneven
surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury
to the operator.
Slots and openings are provided for ventilation must not be blocked or covered. Do not place this unit
on a bed, sofa, rug or other similar surface.
• This product should be operated only with the type of power source indicated on the label. If you are not sure
of the type of power supply to your home, consult your product dealer or local power company.
• This product is equipped with a three-wire plug. This plug will t only into a grounded power outlet. If you are
unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the
safety purpose of the grounded plug.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they
exit from the product.
• For added protection of this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to
the product due to lightning and power line surges.
• Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can
result in a risk of re or electric shock.
• Never push objects of any kind into this product through openings as they may touch dangerous voltage
points or short out parts that could result in a re or electric shock. Never spill liquid of any kind on the product.
• Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltages and other hazards. Refer all service to qualied service personnel.
• Unplug this product from the wall outlet and refer service to qualied service personnel under the following
conditions:
a) When the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen on the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the Operation Manual, as an improper adjustment of controls may result in damage
and will often require extensive work by a qualied technician to restore the product to normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
• When replacement parts are required, be sure the service technician has used replacement parts specied
by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in
re, electric shock, or other hazards.
• Upon completion of any service or repairs to this product, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
• The product should be placed more than one foot away from heat sources such as radiators, heat registers,
stoves, and other products (including ampliers) that produce heat.
• When connecting other products such as VCR’s, and personal computers, you should turn off the power of
this product for protection against electric shock.
• Do not place combustible behind the cooling fan. For example, cloth, paper, matches, aerosol cans or gas
lighters that present special hazards when over heated.
INSTALLATION GUIDELINES
R599900 - Blackwing Series User Manual 7
Do not look into the inside of this unit through vents (ventilation holes). Do not stare into the beam. The
light is so powerful that your eyesight can be impaired. RG2 from the IEC 62471-5:2015 classication.
• Do not drop, hit or damage the light-source lamp (lamp unit) in any way. It may cause the light source lamp
to break and lead to injuries. Do not use a damaged light source lamp. If the light source lamp is broken, ask
your dealer to repair it. Fragments from a broken light-source lamp may cause injuries.
• The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the
light source lamp. If anything is unclear, please consult your dealer.
• Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching xture of the
projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal
injury.
• The power supply rating of this product is AC100V – AC240V, the power cord attached conforms to the
following power supply voltage. Use only the power cord designated by our dealer to ensure Safety and EMC.
• When it is used by other power supply voltage, power cable must be changed. Ensure that the power cable
used for the projector is the correct type for the AC outlet in your country. Consult your product dealer.
• Caution: Do not allow any unqualied person to install the unit. Be sure to ask your dealer to install the unit
(e.g. attaching it to the ceiling) since special technical knowledge and skills are required for installation. If
installation is performed by an unqualied person, it may cause personal injury or electrical shock.
1.4  Imageprojectorclassication
IEC62471-5 labels located at the top front of this unit.
As with any bright light source, do not stare into the beam when this unit is operating. This unit is rated
RG2 from the IEC 62471-5 classication.
2.0  INSTALLATION GUIDELINES
2.1  Introduction
The Blackwing Series projectors are equipped with a three-chip LCoS light engine capable of projecting a picture
resolution of 4096 x 2160 pixels (true 4K). The highest model of the Blackwing Series is the Blackwing Elite that
can display pictures up to 8192 x 4320 pixels resolution thanks to the new 8K Interpolation engine. 8K resolution
is more than 17 times Full-HD resolution.
Supported 2D signals and pixel depth
480p, 576p, 720p@50/60Hz, 1080i@50/60Hz, 1080p@24/50/60Hz
4Kp@24/25/30Hz and UHD: 3840×2160@24/25/30Hz (up to RGB and YCbCr 4:4:4 12 bits pixel depth)
4Kp@50/60Hz and UHD: 3840×2160@50/60Hz (YCbCr 4:2:2 up to 12 bits pixel depth or up to 8 bits for RGB and
YCbCr 4:4:4). Note that the native resolution of this projector is 17:9 ratio, 4096x2160 pixels, 16:9 signals such
as 3840x2160@24/25/50/60Hz or Full-HD are supported and will need to be masked on left and right to eliminate
light leaking on the sides of the screen.
Supported 3D signals
This unit is compatible with 3D playback. The source can be connected using one of the two available HDMI
inputs and will be up-scaled to 4K resolution. The inputs are compatible with the following 3D formats:
• 1080p @ 23.98/24 Hz - Frame Packing, Top & Bottom and Side-by-Side
• 720p @ 50 or 59.94/60 Hz - Frame Packing, Top & Bottom and Side-by-Side
• 1080i/p @ 50/60 Hz - Side-by-Side
R599900 - Blackwing Series User Manual
INSTALLATION GUIDELINES
8
2.2  THX4KDisplayCertication(BlackwingElitemodelonly)
The THX 4K Display certication proves that the Blackwing Elite has undergone over 400
individual tests to ensure color, tone and images reproduce the director’s intentions accurately
in 4k: Amongst the important points, the THX labs have veried upscaling, motion processing,
correct gamma and color accuracy, overscan and scaling. The 4K Display label ensures that
the Blackwing Elite is capable of performing the best images and pristine video performances,
sharper pictures and nest Ultra-HD experiences.
2.3  Environment of Use
Do not install in this following conditions
This unit is a precision device. Please refrain from installing or using it at the following locations. Otherwise, it
may cause re or malfunction.
• Projection with the unit laid on sides.
• Dusty, wet and humid places
• Places subject to oily smoke or cigarette smoke
• On top of a carpet or bedding, or other soft surfaces
• Places exposed to direct sunlight
• Do not install this unit in a room that is oily or subject to cigarette smoke. Even a small quantity of smoke or
oiliness can have a long-term impact on this unit.
• Projection at a place exposed to air blasts from an air conditioner.
This unit produces a great amount of heat, and is designed to take in cool air to cool its optical components.
Using the unit at the above locations may cause dirt to attach to the light path, thereby resulting in dark
images or dull colors. Dirt that sticks to the optical components cannot be removed.
Allowed Inclination during operation
Due to the lamp position and operating angle, this unit cannot operate with more than 5° angle horizontally and
15° angle vertically. This unit cannot be operated on the side.
5°
15°
2.4  Air-FlowandSpaceRequirements
This unit can be installed in table, ceiling, rear table or rear ceiling position. Make sure that the unit is installed
within the space requirements described below (A: air inlets, B: air outlets). This unit needs at least 30 cm of non-
obstructed space on each sides and 15 cm on top to allow sufcient air ow.
B
B
A
A
A
B
B
B A
Air ow.
INSTALLATION GUIDELINES
R599900 - Blackwing Series User Manual 9
2.5  Installing the projection screen
Install the projection screen and this unit such that they are perpendicular to each other as showed in the picture
below.
Place this unit perpendicular to the screen.
Use the electronic shift and zoom to correct the picture size and position as needed. You can also use
the feet to adjust the projected picture level.
Screen material suitable for 4K/8K projection.
To optimize the sharpness and detailing of the picture, please choose a screen material optimized for ultra High
resolution (UHD 4K) or 8K if you are installing a Blackwing Elite. Avoid any material with uniform patterns as
checks that may cause interference artefacts to occur. If this is the case, you can try to slightly change the size
of the projected image to make the interference patterns less noticeable.
2.6  When to use the High Altitude mode
When using this unit at a location that is higher than 900 meters or 3000 feet above sea level and making the air
pressure low enough to decrease its efcacity cooling this unit, set the “High Altitude Mode” to “On”.
2.7  Ceiling Mounting the Unit
AA
A A
d=290 mm
D=337 mm
When mounting of this unit is required, make use of the 4 screw holes (M5x20 screws) at the bottom of this unit
indicated by the letter A. You can remove the feet to insert the ceiling mount screws. Allow sufcient space around
the air inlets to avoid blocking them.
Precautions for Ceiling-mount
• To ceiling-mount this unit, special expertise and techniques are necessary. Be sure to ask your dealer or
specialist to perform mounting.
• Do not mount at places that may be subjected to vibration and shock.
• Depth of the screw holes (A) is 23 mm. Use at least 13 mm long screws but not longer than 23 mm as you
may damage inside the projector.
• Install at a safe place in case this unit or a part of it may drop. If the light-source lamp is broken, small pieces
R599900 - Blackwing Series User Manual
INSTALLATION GUIDELINES
10
of glass from the mesh of the lter may appear outside the unit.
• Regardless whether the unit is still under guarantee, Cineversum is not liable for any product damage caused
by mounting the unit with third party ceiling mount or when the environment is not suitable for ceiling-mount.
Dimensions
• Distances between left and right holes is D = 337 mm.
• Distances between front and back holes is d = 290 mm.
2.8  Projection Distance
Projection Screen
Diagonal Size
(Aspect Ratio 16:9)
Projection Screen
Base Size
(Aspect Ratio 16:9)
Projection Screen
Height
(Aspect Ratio 16:9)
Blackwing Series
Projection Distance
60” (152 cm) 52.3” (133 cm) 29.4” (747 cm) 178 cm - 366 cm
70” (178 cm) 61.0” (155 cm) 34.3” (872 cm) 209 cm - 428 cm
83” (211 cm) 72.3” (184 cm) 40.7” (103 cm) 251 cm - 507 cm
110” (279 cm) 95.9” (244 cm) 53.9” (137 cm) 331 cm - 675 cm
138” (350 cm) 120.3” (306 cm) 67.7” (172 cm) 418 cm - 843 cm
150” (350 cm) 130.7” (332 cm) 73.5” (187 cm) 453 cm - 860 cm
180” (457 cm) 156.9” (306 cm) 88.2” (224 cm) 545 cm - 1107 cm
200” (508 cm) 174.3” (443 cm) 98.1” (249 cm) 606 cm - 1230 cm
230” (584 cm) 200.5” (509 cm) 112.8” (286 cm) 694 cm - 1405 cm
250” (635 cm) 217.9” (553 cm) 122.6” (311 cm) 755 cm - 1528 cm
280” (711 cm) 244.0” (620 cm) 137.3” (349 cm) 846 cm - 1713 cm
• The projection screen sizes and projecting distances in the table above are provided only as a guide. Please
use them as reference during installation.
• 230” up to 280” diagonal screens available with Blackwing Elite models only.
2.9  Setting the Lens and using Lens Memories
Adjust the picture position
The optimum image can be obtained when the centre of this projector’s lens and the screen are placed
perpendicular to each other.
Screen Height
(H)
Screen Base
(B)
Horizontal Shift
+/- 34%
Vertical Shift
+/- 80%
This unit comes with a vertical and horizontal shift to suit most installations. Make sure that your installation
does not exceed 80% vertical offset and 34% horizontal offset to avoid trapezoidal correction.
This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen
INSTALLATION GUIDELINES
R599900 - Blackwing Series User Manual 11
position.
Adjust the picture to your screen.
• The Vertical Shift level is between -80% and 80% of the Screen Height (0.80 x H).
• The Horizontal Shift level is between -34% and 34% of the Screen Base (0.34 x B).
• If the projector is not installed perpendicularly to the screen, use keystone correction to fulll your screen.
Note that using keystone correction, may be disabled by 3D projection. If you want the best possible 3D
pictures, It is not recommended to use trapezoidal correction.
• If you plan to use the vertical and horizontal shifts without keystone correction, make sure to not exceed the
values contained in the tab below for the Blackwing One and Blackwing Two:
Left / Right shift 0% 10% 20% 25% 30% 34%
max. up / down shift 80% 66% 47% 34% 18% 0%
• The Blackwing Elite has an extended shift range as follow:
Left / Right shift 0% 10% 20% 25% 30% 35% 43%
max. up / down shift 100% 87% 72% 58% 45% 22% 0%
•Adjust the picture position
The projector has motorized vertical and horizontal shifts. Browse into the Menu to the [Lens Control] setting
into the Installation menu, select the shift adjustment. Or use the direct access button on the Remote Control
Unit [Lens Control] to make the lens adjustment. You can use self-generated test pattern of the projector or an
external pattern, from a calibration DVD by example, by setting the Adjust pattern option to Off.
•Adjust the picture Zoom
Into the [Lens Control] menu, press the [Ok] button to access the Zoom adjustment. Use the up and down buttons
to adjust the picture size until the screen is completely lled.
•Adjust the Picture Focus
From the [Lens Control] menu, press the [Ok] button to access the Focus adjustment. Use the up and down
buttons to adjust the picture focus
Using Installation Modes
You can save the current picture position, zoom and focus into one of the 10 Installation Modes. Each Installation
Mode uses a memory that stores the current position, zoom, focus of the lens. Additionally, you can set a custom
name of 10 characters or less.
•Current lens setup
All the lens settings will be stored by default into the Installation Mode 1. You can also copy a Mode into another
using the Mode Copy function. Menu > Installation > Installation Mode > Mode Copy. Then you can call back
anytime later the current lens setup using the direct access button [Mode 1] up to [Mode 3] on the RCU.
•Limitations of use
Each memory can store a different picture size and position, but there are limitations on the possible pictures
sizes and positions because of the projector being at a xed location. In order to calculate the best position of the
projector toward the screen, the installer has to make sure that among the different desired pictures, the smaller
one with the smaller zoom, is within the offset limits (horizontal and vertical shifts) of the projector. Once the
position of the projector is determined by the smallest possible picture, double check that the larger one does not
exceed the zoom capacity.
R599900 - Blackwing Series User Manual
REMOTE CONTROL UNIT (RCU)
12
3.0  REMOTECONTROLUNIT(RCU)
Power [On]
Display [PICT. MODE] menu
Conrm button
[BACK] to previous menu
[Hide] the current picture
Standby/ON LED will ash
green when picture is hidden
Display the main [MENU]
Stand by
Backlight button
Gamma Adjust
M.P.C. Settings)
Switch [INPUT]
Displays [Info] menu
Displays [Advanced Menu]
CMD Clear Motion Drive
Display the Installation
Mode menu
Display [COLOR PROFILE] Menu
[LENS CONTROL]
Focus, Zoom, Shift
Directional keys
The remote control unit can be used by having the signal reected off a screen, as the effect of signals
reected differs with the type of screen used, operable distance may decrease.
If the remote control has to be brought closer to the projector to operate, it means that the batteries are
wearing out. When this happens, replace the batteries. Always insert the batteries according to the +
and - marks.
GETTING STARTED
R599900 - Blackwing Series User Manual 13
4.0  GETTING STARTED
4.1  GeneralView
Front side
Optical Lens (/!\)
Air outlet
Operating LEDs
Front IR receiver
Air outlets
(/!\)Optical Lens: This unit comes with a lens plastic cover that is used to protect the lens during transport.
Please remove the lens before rst operation.
Rear side
Inputs Panel Navigation buttons
Main Power
Air inlet
Air inlet Filter compartment
• Input Panel: connect your video source to the correct input.
• Main Power: connect the power cord as shown below.
4.2  ConnectingthePowerCord
• Before plugging in the Power Cord, ensure that all devices have been
connected to their respective inputs of this unit.
• Connect the power cord to the power input terminal of the projector.
When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air inlets or
exhaust vents by standing the projector on its end or laying it on its side.
R599900 - Blackwing Series User Manual
CONNECTIONS
14
4.3  Operating and Navigation Buttons
OK
MENU BACK
INPUT
Menu
OK button
Power button
Rear IR receptor
Directional keys
and input select
Back
Button Description
Back To return to previous menu or cancel action.
Directional keys
and input select
Use the Navigation Keys to navigate into the On Screen Display (OSD) Menu.
Up and Down keys may be used to switch Inputs between HDMI1 and HDMI2
when no OSD menu is shown.
Power button To display the On Screen Display (OSD) Menu.
Menu To display the On Screen Display (OSD) Menu.
OK button To select or to conrm action.
5.0  CONNECTIONS
5.1  CautionwhenconnectingaDevicetoHDMIInput
Prior to connecting any device to this unit, switch the projector in standby mode. Never connect a HDMI
source to this unit when the projector is in operate mode. The HDMI termination is a self-powered
connection and can cause electric discharges.
The HDMI 2.0 inputs are compatible with HDCP 2.2 and supports video signals up to 18 Gbps. It is
strongly recommended to use exclusively cables rated for 18 Gbps bandwidth to watch 4K contents,
otherwise this unit will suffer from handshake issues and video freezes.
CONNECTIONS
R599900 - Blackwing Series User Manual 15
5.2  Connecting a Video Source to the Projector
HDMI 1 HDMI 2
RF Dongle
or
3D syncro
Emitter
Audio/Video Connection Device to connect
HDMI 1, HDMI 2
(DVI compatible)
HDMI or DVI-D sources: Blu-ray Disc player, DVD-player equipped with an HDMI
output, Game Console, Computer with DVI-D output.
RF Dongle or 3D Synchro
Emitter
Connect the RF Dongle emitter to control the active 3D shutter glasses or any
other 3D Synchro apparel. 3-PIN mini-DIN interface, 12V.
This unit supports up to 4Kp60 inputs, make sure to use high quality HDMI cables rated for at least 4K
HDMI 2.0 standards (18 Gbps).
5.3  Connecting an Automation or Control device
to LAN rooter
for Automation
RS-232C
for Automation
12V Trigger
Connection Device to connect
RS-232 C Automation Device, Control Device or Computer with RS-232 capability.
12V Trigger DC power supply output 12V@100mA to control either a screen or an anamorphic
lens motorization.
LAN Automation Device, Control Device or Computer with RJ-45.
CONNECTING AN AUTOMATION/CONTROL DEVICE
This unit can control or be controlled by using several input/output terminals. Each terminal is ruled by
specic protocols. Please refer to Appendix for more information.
ECO Mode turn to On prevents this unit to receive and to respond to automation commands when it is in
standby. Turn Off ECO mode if you plan to take full control of this unit with an automation system.
R599900 - Blackwing Series User Manual
FIRST START Up
16
6.0  FIRST START UP
Always remove the lens cover or lens protection before powering up this unit. To power up this unit,
make sure that the power cord is connected to the power input terminal.
6.1  TurnthepowerON
You can turn ON this unit with the remote control unit (RCU) or directly pressing the power button located on the
back panel. During startup procedure, this unit Standby/Power LED will blink green. Wait until complete power
ON indicated by a steady green light on the Standby/Power LED.
Back panel
If “Eco mode” is On, the standby led will not be light up red during Standby mode.
Select the correct Input
Once this unit is powered ON, please select the correct Input by pressing the corresponding button on the
Remote Control Unit or the O/I button on the back panel of this unit.
6.2  TurnthePowerO
You can turn OFF this unit by using either the RCU or the Power button on the rear control button panel.
Press the Standby button and a message appears on the screen to ask to conrm the command. You can cancel
the command by pressing the “Back” button or turn off the device by pressing the “Standby” button again.
The Standby LED will switch from steady green to blinking red light and the fans will run for about 10 seconds
to nish the shutdown procedure. During this Cool-down sequence, do not disconnect the power cord. The cool-
down procedure is nished when the “Standby/On” LED indicator stops blinking red and switches to a solid red.
The power cannot be turned off within approximately 80 seconds after it has been turned on.
The power cannot be turned On again until the Cool-down sequence (10 seconds) is complete.
It is recommended to disconnect the power plug when the unit is not to be used for a prolonged period of
time (superior to one week) to avoid any electrical hazards.
MENU STRUCTURE
R599900 - Blackwing Series User Manual 17
7.0  MENU STRUCTURE
MAIN MENU SUBMENU AVAILABLE OPTIONS
Picture Adjust Picture Modes
(4+6 User)
(Video and drama programs) Natural
(Vivid colors suitable for all movies) Cinema
(HDR10 movies, auto tone mapping) HDR10
(HDR movies using Hybrid Log) HLG
(Movie lms N.A. with Blackwing One) Film
(Blackwing Elite only) THX
User 1 - 6
Expert Picture Modes
(*) require individual calibration
THX bright(*)
THX dark(*)
Advanced Picture Mode
(press OK to enter this menu)
Lamp Power Low, High
Aperture Auto 1
Auto 2
Manual: -15 +0
User Name Edit (if f User 1 - 6 selected)
Edit name 10 char. max
Color Proles
the list varies upon the selected
Picture Mode
(*) require individual adjustment
and/or calibration
(HDTV REC-709) BT.709
(Movies REC 2020) BT.2020
(Cinema DCI-P3) DCI
(Drama or Live events) Video
(Animations) Anime
(Movies with enhanced colors) Cinema
(HDR contents) HDR
(Eastman Kodak movies) Film1
(Fujilm movies) Film2
(Blackwing Elite only) THX
Off
Custom 1 - 6(*)
Advanced Color Prole Color Management: Off / On
Color selection
Axis Position -30 +30
Hue -30 +30
Saturation -30 +30
Reset Conrm
Color Temp Xenon Modes
(Film projector) Xenon 1
(DCI projector) Xenon 2
Preset value:
5500K, 6500K, 7500K, 9300K,
High Bright, HDR10, HLG, Custom 1-2
Advanced Color Temp If Custom 1-2, choose Correction Value
Gain and Offset settings
Reset Conrm
Gamma If Color Prole is Film1 or 2
(Blackwing Two & Blackwing Elite only)
(standard) Film1
(more contrasted) Film2
Custom1 to 3
If Color Prole is THX (Blackwing Elite) THX
If Color Prole is not Film nor THX
Normal, 2.2, 2.4, 2.6,
Cinema 1, Cinema 2
HDR (PQ), HDR (HLG)
Custom 1, Custom 2
R599900 - Blackwing Series User Manual
MENU STRUCTURE
18
Picture Adjust Advanced Gamma If Custom 1 or 2, Gamma Corr. Value
1.8 - 2.6 (within 0.1 steps)
Cinema 1, Cinema 2
HDR (PQ), HDR (HLG)
Import
Auto Tone Mapping On, Off
Mapping Level -7 +7
Color Selection White / Red / Green / Blue
Picture Tone -16 +16
Dark Level -7 +7
Bright Level -7 +7
Reset Conrm
MPC Level / MPC e-shift 8K e-shift (Blackwing Elite only, NA with 3D)
On(8K), Off(4K)
Graphic Mode Standard, High-Res (4K)
Enhance 0 - 10
Smoothing 0 - 10
Noise Reduction 0 - 10
Reset Conrm
Motion Control Low Latency (NA with 3D and if CMD is On)
On, Off
Clear Motion Drive (NA if Low Latency is On)
Off, Low, High, Inv. telecine
Motion Enhance (NA with 3D) Off, Low, High
Contrast -50 +50
Brightness -50 +50
Color -50 +50
Tint (reddish to greenish) -50 +50
Reset Prole settings Conrm
Input Signal Input level Auto
16 - 235 (Video)
0 - 255 (PC)
16 - 255 (S. White)
Color Space Auto,
YCbCr444
YCbCr422
RGB
3D Setting 3D format
Auto / Side-by-Side / Top & Bottom / 2D
Parallax -15 +15
Crosstalk Cancel -8 +8
HDR Settings HDR10 Auto Select HDR10, User 1 to 6, Off
HLG Auto Select HLG, User 1 to 6, Off
HDMI2 EDID (HDMI2 only) A, B
Installation Installation Mode Mode Select Mode 1 - Mode 10
Name Edit 10 char. max
Mode Copy Select Mode and Conrm
Lens Control Focus
Zoom
Shift
Image Pattern On, Off
Lock On, Off
Lens Center Conrm
Pixel Adjust Adjust On, Off
Adjust Area Whole, Zone
Adjust Color Red, Blue
Adjust Pattern On, Off
Adjust Pattern Color White - Cyan/Yellow
MENU STRUCTURE
R599900 - Blackwing Series User Manual 19
Installation Pixel Adjust Adjust (Pixel)
Adjust (Fine)
Reset Conrm
Mask On, Off
Top, Bottom, Left, Right 0 - 220
Anamorphic Off, A, B, C
Screen Adjust
(Color Prole must be On)
Screen No. 000 - 255
On, Off
Installation Style Front, Ceiling Mount, Rear, Ceiling Mount (Rear)
Keystone (vertical) (N.A. if Pincushion is On) -16 +16
Pincushion (N.A. if Keystone On) 0 - 16
Aspect Zoom
Auto
Native
Display Setup Back Color (when no signal) Blue, Black
Menu Position select position
Signal Display (active input) On, Off
Logo On, Off
Language select between 13 languages
Function Trigger Off
Power
Anamo
Inst. Mode 1 - Inst. Mode 10
Off Timer (in hours) 1H, 2H, 3H, 4H, Off
ECO Mode On, Off
Network DHCP Client On, Off
IP Address 192.168.0.2
Subnet Mask 255.255.255.0
Default Gateway 192.168.0.254
Mac Address Display MAC
Set Conrm
Remote Code Press [Menu] + [Back] A, B
High Altitude Mode (900m or higher) On / Off
Lamp Reset
Factory Reset
Software Update
Information Display Information menu
R599900 - Blackwing Series User Manual
pICTURE ADjUST
20
8.0  PICTURE ADJUST
8.1  PictureModesandColorProles
The preset Picture Modes are available and they can be applied to any input. A picture mode retains the picture
adjustments. When adjusting the Picture Mode, you can also select pre-congured Color Proles.
Type of source Movie
or HDTV
Dramas
or Videos
HDR sources Film THX
Picture mode Cinema Natural HDR10 / HLG Film THX
Color Proles
BT.709 BT.709 BT.709 Film 1 THX
BT.2020 BT.2020 BT.2020 Film 2
DCI DCI DCI
Video Anime HDR
HDR HDR
There is a total of 6 Picture Mode presets for Blackwing One, 6 for Blackwing Two models and 5 User. For each
prole, you may choose one of the available Color Prole presets:
• Film 1 available with Film Picture Prole, uses the Xenon lter and adjusted to Eastman Kodak lm tone
• Film 2 available with Film Picture Prole, uses the Xenon lter and adjusted to Fujilm lm tone.
• Film 3 available with Film Picture Prole, uses the Xenon lter and adjusted to Technicolor lm tone.
• Standard will bring rich and saturated colors found in HDTV, using REC 709 color space.
• Cinema 1 available with Cinema Picture Prole and adjusted to movie sources with bright, saturated colors.
• Cinema 2 available with Cinema Picture Prole and adjusted to DCI-P3 color space.
• Animation/Anime 1 best suited to Hollywood animations.
• Anime 2 best suited to Japanese animations.
• HDR10 that is best suitable for HDR movies in general.
• BT.2020 that is optimized for HDR movies encoded with REC 2020 color space.
• Video color prole is best suited to TV and Sport programs.
• Reference color prole is used to reproduce faithfully the source colors.
• THX color prole is reserved for the THX picture modes.
8.2  Advanced Picture Mode
Lamp Power
Set the lamp power used by the current Picture Prole. For standard viewing conditions, the lamp power is set to
Low. To obtain a brighter image, set it to High but this setting may cause the lamp to darken faster.
Aperture and High Contrast Images
The lens is equipped with a variable electronic aperture. This function is used with a real time analysis of the video
picture projected that optically adjusts the light output depending on the viewing conditions by controlling the
aperture dynamically. Thanks to sensitive and perfectly controlled adjustments, the contrast image is drastically
boosted. When set to Auto 1, this setting makes the iris to automatically set to the optimal opening to enhance
the picture contrast. The Auto 2 setting, the result obtained is altered so that the gradation is more visible. The
Manual setting sets the iris to a xed position, adjust the aperture from partially closed (-15) to fully opened (0).
User Name Edit
You can edit the picture modes names User 1 to User 6 using a maximum length of 10 characters. You can use
alphabet letters, numbers and symbols:
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Cineversum BlackWing One MK2019 User manual

Cineversum
Brand
Cineversum
Model
BlackWing One MK2019
Category
Data projectors
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents