OPT7 Redline F150 User manual

Redline F150
Brand
OPT7
Model
Redline F150
Type
User manual

OPT7 Redline F150 is a quick connect expansion adapter harness designed for 2018-2020 Ford F150 models without BLIS/backup camera/assist sensor. It enables a plug-and-play installation of trailer accessories, providing a seamless and virtually hidden connection without cutting or splicing factory harnesses. The adapter features a flat 4-pin trailer connector and reverse wire, allowing for easy connection of trailer lights and reverse cameras. Installation involves accessing the taillights, unplugging the OEM wiring harness, and connecting the Redline adapter.

OPT7 Redline F150 is a quick connect expansion adapter harness designed for 2018-2020 Ford F150 models without BLIS/backup camera/assist sensor. It enables a plug-and-play installation of trailer accessories, providing a seamless and virtually hidden connection without cutting or splicing factory harnesses. The adapter features a flat 4-pin trailer connector and reverse wire, allowing for easy connection of trailer lights and reverse cameras. Installation involves accessing the taillights, unplugging the OEM wiring harness, and connecting the Redline adapter.

Redline
FOR FORD F150 XL,XLT,LARIAT
NO BLIS/BACKUP CAMERA/ASSIST SENSOR
Hello Fellow OPT7-ites, Introducing the Redline Quick Connect Harness to Flat
4-Pin Extension Adapter Harness
The OPT7 Redline Quick Connect Expansion Adapter Harness is purpose-built to
be used as a trailer accessory for 18-20 F150 models. It provides a plug-and-play
style that allows you to quickly, seamlessly and virtually hidden installation
without cutting or splicing your factory harnesses.
3.94”
3.94”
110.23”
70.87”
Expansion
Adapter
2018-2020
Installation
Step 1Step 1
Important
Figure 1Figure 1
Step 2Step 2
Figure 2Figure 2
Step 3Step 3
Figure 3Figure 3
Tail light
Connector
Tail light
Connector
Release Latch
Release Latch
OEM Wiring
Harness
OEM Wiring
Harness
Open up your tailgate first.
Next, locate the two bolts that
lock the tail light (See Figure 1)
and loosen them.
Slowly move the loose tail light
until it is completely removed (See
Figure 2).
There are two plastic clips on
the inside of the tail light for
fixing, please be careful not to
break it when removing it.
Locate the OEM wiring harness
(See Figure 3) and unplug it from
the tail light assembly by lightly
pressing the Release-Latch on the
connector.
To make it easier for you to identify the signal location represented by the
Connector/Wiring. Please read the relevant wiring instructions carefully before
commencing any work.(See Figure 4)
OEM TAIL LIGHTS
White = Reverse
White
Brown
Yellow
Green
=
=
=
=
Ground
Tail Lights
Left Turn & Brake
Right Turn & Brake
RIGHT
Passenger Side
LEFT
Driver’s Side
HOW TO CONNECT
PnP EXPANSION ADAPTER TO YOUR TAILLIGHTS
Tail light Connector
OEM Wiring Harness
Tail light Connector
OEM Wiring Harness
R
L
Step 4Step 4
Figure 4Figure 4
NOTE
There will be two types of appearance on the tail light connector. The product is only
compatible with TYPE "A".
If your truck has TYPE "B", please remove the excess plastic on the wire harness plug
we provided, this will help you in the following installation. (See below for details)
Just remove it ,if necessary
Just remove it ,if necessary
A B
Installation
DISCLAIMER
Step 6
Step 7
Step 5Step 5
Figure 5Figure 5
OEM Wiring
Harness
OEM Wiring
Harness
OPT7 Lighting is not liable for damages or personal injuries while installing this
product. The Installation Guide is intended as assistance to reduce setup time.
OPT7 Lighting assumes no responsibility for improper installation.
If you are unfamiliar with your vehicle or inexperienced with aftermarket
upgrades, please seek professional assistance.
OPT7 recommends installation for safety and guidance.
Modified installations or installation recommendations not specified by OPT7
Lighting will void product warranty.
Next, grab the Redline Quick
Connect Expansion Adapter
Harness and Plug it into the
vehicle’s OEM wiring harness.
Plug the other end into the tail
light connector (See Figure 5).
Route the Redline Quick Connect
Expansion Adapter Harness from
the left tail light opening to the
right tail light opening, then
repeat the same steps for the
other side.
Use some zip ties to secure the flat 4PIN trailer
connector and reverse wire in place along the inner
bumper.
Finally, connect the available tailgate light bar to the
4PIN trailer connector and reverse wire for full
functionality testing
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

OPT7 Redline F150 User manual

Redline F150
Brand
OPT7
Model
Redline F150
Type
User manual

OPT7 Redline F150 is a quick connect expansion adapter harness designed for 2018-2020 Ford F150 models without BLIS/backup camera/assist sensor. It enables a plug-and-play installation of trailer accessories, providing a seamless and virtually hidden connection without cutting or splicing factory harnesses. The adapter features a flat 4-pin trailer connector and reverse wire, allowing for easy connection of trailer lights and reverse cameras. Installation involves accessing the taillights, unplugging the OEM wiring harness, and connecting the Redline adapter.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents