EchoStar DVR-7000 HDD Viaccess Supplementary Manual

Service Letter

EchoNAV software version 2.2

EchoNAV User Interface

for Digital Satellite Receivers

HDD

Printed on recycled paper

Issue: echonav_hdd_sl_22a_us

We encourage you to express your thoughts on this service letter.

Please send your comments to:

EchoStar International Corporation

Technical Publications Department

Schuilenburglaan 5a

7604 BJ Almelo

The Netherlands

Preface

EchoNAV 2.2 Page I

PREFACE

1. DEAR CUSTOMER

This service letter introduces version 2.2 for the EchoNAV user interface which supersedes

the previous service letter(s). For your convenience the highlights of the previous software

are also given.

THE HIGHLIGHTS FOR VERSION 2.2

■ Two menu languages added;

■ Revised help lines and related translations;

■ Revised subtitle behaviour;

■ Russian and Greek subtitle languages added;

■ Multilingual EPG language support added;

■ Revised conditional access to support smartcards type PC2.4;

■ Revised channel numbering for Current SAT list;

■ New installation menus added for multiple LNB support;

■ Revised Add SAT, TP and PID menus;

■ Pre-defined LNB (LO 10,700) added to LNB list;

■ User LNB settings menu are moved to the Advanced mode;

■ New option to add satellite or transponder during initial installation setup added;

■ OTA service added on ASTRA1, 19.2 East.

■ DVR timer modified to allow for recording a relative time block.

■ Updated satellite/transponder database

THE HIGHLIGHTS FOR PREVIOUS VERSION 2.0

■ Six menu languages added;

■ Group and Sort behaviour revised to remember the last setting;

■ Extended channel information available with i-key;

■ Move function extended with recall option;

■ Edit functions, Move, Lock and Delete separated;

■ Save changes pop-up menu added.

■ Updated satellite/transponder database

DVR-7000 HDD ONLY

■

Photo album added;

■ New MP3Loader made available with embedded BackgroundLoader and PhotoLoader;

■ Installation menu added for Set East and West Limit;

■ Improved positioner behaviour.

2. INTENDED USE

This service letter is intended for anyone who uses an EchoStar satellite receiver with an

EchoNAv user interface. It can be used by both first-time and experienced users who want to

install, use and maintain their receiver.

This service letter is applicable for the Digital Satellite Receiver with Hard Disk:

■ DVR-7000 HDD Viaccess;

■ DVR-7000 HDD;

■ DVR-5000 HDD Viaccess;

■ DVR-5000 HDD.

This service letter is divided into separate sections and chapters for easy reference to the

applicable chapters of your user manual. Please keep this service letter next to your user

manual for future reference.

Preface

Page II EchoStar International Corporation

3. DISCLAIMER

SATELLITE RECEIVER

EchoStar International Corporation has done everything to the best of her abilities, to supply

you with a satellite receiver built to the most up-to-date software and hardware. EchoStar

International Corporation makes no warranties with respect to the reception of the channels

provided by the broadcast service providers and specifically disclaims any implied warranties

of merchantability or fitness for any particular purpose.

EchoStar International Corporation reserves the right, for whatever reason, to revise, change

or modify the hard- and software of the satellite receiver without the obligation to notify or

warrant any person or organization of such change. Therefore, please visit our website, on a

regular basis, for the latest information available.

SOFTWARE DOWNLOADS

EchoStar International Corporation will do everything to the best of her abilities, to supply you

with software updates to keep your receiver as up-to-date as technically possible. EchoStar

International Corporation makes no warranties with respect to the use of the supplied

software downloads and specifically disclaims any implied warranties of merchantability or

fitness for any particular purpose.

EchoStar International Corporation reserves the right, for whatever reason, to revise, change

or modify the software that can be used by your satellite receiver without the obligation to

notify or warrant any person or organization of such change. Therefore, please visit our

website, on a regular basis, for the latest software available.

SERVICE LETTER

EchoStar International Corporation has done everything to the best of her abilities, to supply

you with the most up-to-date information. EchoStar International Corporation makes no

warranties with respect to the information provided by this service letter and specifically

disclaims any implied warranties of merchantability or fitness for any particular purpose. The

information provided is meant as a guideline for the use and maintenance of the receiver.

EchoStar International Corporation reserves the right to right, for whatever reason, change or

translate this service letter without the obligation to notify any person or organization of such

change. Therefore, please visit our website, on a regular basis, for the latest information

available.

Preface

EchoNAV 2.2 Page III

TABLE OF CONTENTS

Preface

1 DEAR CUSTOMER I

2 INTENDED USE I

3DISCLAIMER II

Installation

1 TO SETUP YOUR RECEIVER FOR THE FIRST TIME 3-1

2 ADVANCED MODE (MULTIPLE LNB SUPPORT) 3-7

Familiarization

1 ECHONAV 2.2 4-1

2 THE ECHONAV INSTALLATION MENU 4-3

3 THE ECHONAV MODE AND SELECTION MENUS 4-10

4 THE INDEX MARKERS 4-13

5 THE TIMERS 4-14

Operation

1 TO NAVIGATE THROUGH THE MENUS 5-1

2 USE THE FAVORITE LISTS 5-5

3 TO SELECT ANOTHER SATELLITE 5-6

4 TO USE THE INDEX MARKERS 5-6

5 TO USE THE PHOTO ALBUM 5-8

6 TO USE THE DVR STOP TIMER 5-9

Maintenance

1 USER LNB SETTING - SUB-MENU (ADVANCED ONLY) 6-1

2 SET LIMITS - SUB-MENU 6-1

3 SEARCH CHANNELS - ANALOG IF 6-2

4 ADD DATA (SAT/TP) - SUB-MENU 6-2

Troubleshooting

1 TO SOLVE AN INSTALLATION RELATED PROBLEM 7-1

Glossary

1 LIST OF USED ABBREVIATIONS 8-1

2 EXPLANATION OF USED TERMINOLOGY 8-2

Index

Appendix 1

1 LNB CONFIGURATION MATRIX A1-1

2 LNBF CONFIGURATION MATRIX A1-1

3 USER DEFINED LNB(F) MATRIX A1-2

Preface

Page IV EchoStar International Corporation

Installation

Section 3

EchoStar International Corporation Page 3 - 1

3

INSTALLATION

1. TO SETUP YOUR RECEIVER FOR THE FIRST TIME

This procedure supersedes the procedure as given in the user manual from step 15 onwards.

The main differences are:

■ Select Easy or Advanced installation,

Easy installation helps you to do the initial setup procedure where Advanced allows you to

program the receiver as required for non-standard installations.

■ Add a new satellite,

In a satellite field you can select any known satellite in range from the database or add

your own defined satellite with the use of the S00 satellite.

■ Add a new transponder,

In a transponder field you can select any known transponder from the database or add

your own defined transponder with the use of the TP00 transponder.

FOR ALL CONFIGURATIONS

FOR FIXED AND DISEQC 1..4 SWITCH CONFIGURATIONS - EASY

NOTE

From the next step onwards, the procedure is divided in different configurations. The

configurations are; Fixed, Motorized and SMATV.

■ Fixed means set up a single dish or multiple dishes with DiSEqC1..4 switch;

■ Motorized means set up a moveable dish (motor/actuator by positioner);

■ SMATV means set up for television distribution (cable network in buildings).

1. Make the required selections.

2. Read the available help text for information.

3. Go to the Save settings field to confirm the time.

4. On the RCU, press the OK key to set the time.

Note that the local time is shown correctly.

5. Go to the Continue field.

6. On the RCU, press the OK key to advance

21. Make the required selections.

22. Set the required installation mode, recommended

setting is Easy (guided setup procedure).

23. Read the available help text for information.

Note that only the white fields are selectable, other

fields show reference information.

24. If you want to add your own defined satellite, go to

the SAT field and select S00 (Goes to the menu

where you can define your own satellite, for

detailed information, refer to section 6). If not

proceed with step 25.

25. Go to the Check signal field.

26. On the RCU, press the OK key to advance.

Section 3

Installation

Page 3 - 2 EchoNAV 2.2

FOR MOVEABLE DISH INSTALLATIONS (DISEQC 1.2)

27. Wait for the Checking configuration to complete.

28. Read the available help text for information.

29. Make the required selections.

30. If the red dot in the TP field stays:

a. select another transponder;

b. go to the Check signal field;

c. on the RCU, press the OK key.

31. If you want to add your own defined transponder,

go to the TP field and select TP00 (Goes to the

menu where you can define your own transponder,

for detailed information, refer to section 6). If not

proceed with step 32.

32. Go to the Search channels field.

33. On the RCU, press the OK key to advance.

34. Wait for the search to complete:

a. the receiver display shows a moving dot;

b. the Search completed popup menu appears.

35. On the RCU, press the OK key to end the initial

setup procedure.

21. Make the required selections.

22. Set the required installation mode, recommended

setting is Easy (guided setup procedure).

23. Read the available help text for information.

Note that only the white fields are selectable, other

fields show reference information.

24. Go to the Program Satellites field.

25. On the RCU, press the OK key to advance.

26. Select the satellite which you want to receive.

27. Read the available help text for information.

Note that only the white fields are selectable, other

fields show reference information.

28. If you want to add your own defined satellite, go to

the SAT field and select S00 (Goes to the menu

where you can define your own satellite, for detailed

information, refer to section 6. If not proceed with

step 34.

Installation

Section 3

EchoStar International Corporation Page 3 - 3

3

FOR MOTORIZED CONFIGURATIONS - AUTOSAT

29. When in the Position field:

a. press and hold theor key and watch the

signal indicator for an indication;

b. in the signal indicator, make sure a network

name is shown;

c. press thekey to select another transponder for

signal verification;

d. press thekey to select the Position field;

e. use thekey to fine tune for the best signal

level and quality;

f. press the OK key, note that the saved position of

the satellite is shown.

30. If you want to add your own defined transponder for

the selected satellite, go to the TP field and select

TP00 (Goes to the menu where you can define your

own transponder, for detailed information, refer to

section 6). If not proceed with step 36.

31. Go to the Search channels field.

32. On the RCU, press the OK key to advance.

33. Wait for the search to complete:

a. the receiver display shows a moving dot;

b. the search completed popup menu appears.

34. On the RCU, press the OK key. to end the initial

setup procedure.

CAUTION

On the motorized dish, set the physical East and West limit switches first. Failing to

do so might cause damage to your motorized dish installation or other properties.

21. Make the required selections.

22. Set the required installation mode, recommended

setting is Easy (guided setup procedure).

23. Read the available help text for information.

Note that only the white fields are selectable, other

fields show reference information.

24. Go to the Autosat field.

25. On the RCU, press the OK key to advance.

Section 3

Installation

Page 3 - 4 EchoNAV 2.2

26. On the RCU:

a. press thekey to set the EL (East limit);

b. at the Motor error, press thekey once;

c. press the OK key.

27. On the RCU, press the OK key.

28. Select the most East SAT which you can receive.

29. If you want to add your own defined East SAT,

select S00 (Goes to the menu where you can

define your own satellite, for detailed information,

refer to section 6). If not proceed with step 31.

30. If you want to add your own defined transponder

for the selected satellite, go to the TP field and

select TP00 (Goes to the menu where you can

define your own transponder, for detailed

information, refer to section 6). If not proceed with

step 31.

31. When in the Position field:

a. press and hold thekey and watch the signal

indicator for an indication;

b. in the signal indicator, make sure a network

name is shown;

c. press thekey to select another transponder for

signal verification;

d. press thekey to select the Position field;

e. use thekey to fine tune for the best signal

level and quality;

f. press the OK key, note that the saved position of

the satellite is shown.

32. Repeat the procedure for the middle and most

West SAT.

33. Set the WL (key), refer to step 26.

34. Go to the SAT list field.

35. On the RCU, press the OK key to advance.

Installation

Section 3

EchoStar International Corporation Page 3 - 5

3

FOR MOTORIZED CONFIGURATIONS - MANUAL SELECTION

36. Make the required selections.

37. Read the available help text for information.

38. Go to the Search channels field.

39. On the RCU, press the OK key to advance.

40. Wait for the search to complete:

a. the receiver display shows a moving dot;

b. the Search completed popup menu appears.

41. On the RCU, press the OK key to end the initial

setup procedure.

CAUTION

On the motorized dish, set the physical East and West limit switches first. Failing to

do so might cause damage to your motorized dish installation or other properties.

21. Make the required selections.

22. Set the required installation mode, recommended

setting is Easy (guided setup procedure).

23. Read the available help text for information.

Note that only the white fields are selectable, other

fields show reference information.

24. Go to the Method field and select Manual.

25. Go to the Set limits field.

26. On the RCU, press the OK key to advance.

Section 3

Installation

Page 3 - 6 EchoNAV 2.2

27. On the RCU:

a. press thekey to set the EL (East limit);

b. at the Motor error, press thekey once;

c. press the OK key.

28. On the RCU:

a. press thekey to set the WL (west limit);

b. at the Motor error, press thekey once;

c. press the OK key.

29. Go to the Program satellites field.

30. On the RCU, press the OK key to advance.

31. Select the satellite which you want to receive.

32. Read the available help text for information.

Note that only the white fields are selectable, other

fields show reference information.

33. If you want to add your own defined satellite, go to

the SAT field and select S00 (Goes to the menu

where you can define your own satellite, for

detailed information, refer to section 6. If not

proceed with step 34.

34. When in the Position field:

a. press and hold theor key and watch the

signal indicator for an indication;

b. in the signal indicator, make sure a network

name is shown;

c. press thekey to select another transponder for

signal verification;

d. press thekey to select the Position field;

e. use thekey to fine tune for the best signal

level and quality;

f. press the OK key, note that the saved position of

the satellite is shown.

35. If you want to add your own defined transponder

for the selected satellite, go to the TP field and

select TP00 (Goes to the menu where you can

define your own transponder, for detailed

information, refer to section 6). If not proceed with

step 36.

36. Go to the Search channels field.

37. On the RCU, press the OK key to advance.

38. Wait for the search to complete:

a. the receiver display shows a moving dot;

b. the Search completed popup menu appears.

39. On the RCU, press the OK key to end the initial

setup procedure.

Installation

Section 3

EchoStar International Corporation Page 3 - 7

3

FOR SMATV CONFIGURATIONS

2. ADVANCED MODE (MULTIPLE LNB SUPPORT)

21. Make the required selections.

After the initial installation it is possible to add more

symbol rates. Refer to section Maintenance for

detailed instructions.

22. Read the available help text for information.

23. Go to the Search Channels field.

24. On the RCU, press the OK key to advance.

25. Wait for the search to complete:

a. the receiver display shows a moving dot;

b. the Search completed popup menu appears.

26. On the RCU, press the OK key to end the initial

setup procedure.

21. Make the required selections.

22. Use thekey to set the installation mode to

Advanced.

23. Note that the screen changes into the advanced

mode.

24. .If you want to return to the Easy mode, use

thekey to set the installation mode to Easy.

25. Read the available help text for information.

26. Go to the Set limits field.

27. On the RCU, press the OK key to advance.

28. Read the available help text for information.

29. Make the required selections.

30. Go to the Program satellites field.

31. On the RCU, press the OK key to advance.

Section 3

Installation

Page 3 - 8 EchoNAV 2.2

32. Select the satellite which you want to receive.

33. Read the available help text for information.

Note that only the white fields are selectable, other

fields show reference information.

34. If you want to add your own defined satellite, go to

the SAT field and select S00 (Goes to the menu

where you can define your own satellite, for

detailed information, refer to section 6).

35. Go to the User LNB field and on the RCU press the

i-key.

36. Note that the software advances to the

User LNB setting menu.

37. Read the available help text for information.

38. Make the required selections.

39. Go to the Save settings field.

40. On the RCU, press the OK key to advance.

41. Note that the software returns to the Program

satellites menu.

42. Make the required selections.

43. If you want to add your own defined transponder

for the selected satellite, go to the TP field and

select TP00 (Goes to the menu where you can

define your own transponder, for detailed

information, refer to section 6).

44. Go to the Search channels field.

45. On the RCU, press the OK key to advance.

46. Wait for the search to complete:

a. the receiver display shows a moving dot;

b. the Search completed popup menu appears.

47. On the RCU, press the OK key to end the initial

setup procedure.

Familiarization

Section 4

EchoStar International Corporation Page 4 - 1

4

FAMILIARIZATION

1. ECHONAV 2.2

The software of the receiver contains the EchoNAV user interface with on-screen help, which

gives you easy control over the features of the receiver. The software contains also a large

database of pre-programmed satellites and transponders which are used for a quick

installation. For initial installation, the software guides you through the required setup menu to

allow for an easy and reliable installation setup of the receiver.

FEATURE HIGHLIGHTS

The highlights for this version are:

■ New menu languages added;

Portuguese, Dutch.

■ Revised help lines and related translations;

All menu texts are revised to give more support and information. All menu languages are

translated accordingly.

■ Several small menu changes incorporated:

- LNB power option in system setup menu for SMATV deleted,

- Time zone option in Local time menu deleted,

- Software identification in About EchoStar menu is changed to show EchoNAV version.

■ Revised subtitle behavior;

Greek and Russian subtitle support is added.

■ Multi-lingual language support for EPG added;

If available form the service provider, EPG language is shown in the language which is set

for the menu language (user preferences - Languages - Menu).

■ Revised conditional access to support smartcards type PC2.4;

The embedded Viaccess smartcard reader is revised to support the latest generation of

PC2.4 smartcards as used by several service providers who use Viaccess encryption.

■ Revised channel numbering for Current SAT list;

The Current SAT list is revised to have it’s own channel numbering. Therefore the channel

numbering (only for Current SAT) starts at 1 for each satellite. Note that also the satellite

name is shown permanently.

■ New installation menus added for multiple LNB support;

The installation menu is revised to support Easy and Advanced installation. In the

advanced installation you can define user defined LNBs where the Easy installation allows

for the installation of pre-defined LNBs.

■ Revised Add SAT, TP and PID menus;

The Add SAT, Add TP, and Add PID are combined in one menu Add data.

■ New option to add satellite or transponder during initial installation setup added;

Add Data menu is accessible from the initial setup and after installation from the channel

list through the ‘white edit’ menu.

■ OTA service added on ASTRA1, 19.2 East.

■ DVR timer modified to allow for recording a relative time block;

The DVR timer is directly accessible after a recording is started. You can set the stop time

either in absolute time (13:00 hr) or relative time (+ 00:15 min).

■ Updated satellite/transponder database,

You have to perform a factory reset to activate the database, failing to do so keeps the

previous database active.

Section 4

Familiarization

Page 4 - 2 EchoNAV 2.2

1.1. THE REMOTE CONTROL UNIT (RCU)

The EchoStar Quattro is a programmable RCU that also can control your TV, VCR, DVD

and/or Audio set. The EchoStar Quattro requires two AA/R6 alkaline batteries to operate.

■ ON/STANDBY

To switch to standby or on.

■ VCR

To control the VCR.

■ TV

To control the TV.

■ EPG

To view the EPG.

■ MENU

To go to the installation menu;

To go to the special functions.

■ VOL+

To increase the volume.

■ VOL-

To decrease the volume.

■ ARROW CLUSTER

To scroll left, up, right or down.

■ EXIT

To leave a menu or feature.

■ PAGE+

To go one page up.

■ PAGE -

To go one page down.

■ ALT AUDIO

To choose a language.

■ ALT SUBTITLE

To choose a subtitle.

■ STOP

To stop the recording or play

back of an event;

To return to actual time in the

EPG window

■ REWIND

To go to the beginning of an

recorded event fastly.

■ RECORD (press twice)

To record a live program.

To show the DVR stop timer.

■ PREVIOUS

To go to the previous event.

■ GREEN

To select a (favorites) list.

■ RED

To go to another mode.

■ NUMBER KEYS

To enter numerical settings;

To type in a channel number.

■ TV/RAD

To switch to TV or Radio

mode.

■ MUTE

To blank out the volume.

■ AUX

To control the Audio Set or

DVD.

■ SAT

To control the receiver.

■ i

To view the InfoBanner;

To view detailed EPG

information.

■ Satellite Dish

To select another satellite.

■ CH+

To go one channel up.

■ CH-

To go one channel down.

■ OK

To go to the (favorites) lists;

To make a menu selection;

To pull down a selection menu.

■ RECALL

To go to the previous channel;

■ ?

Not used for Sat-mode.

■ V (white)

To edit a list

■ PLAY

To play back a recorded event.

■ FAST FORWARD

To go to the end of an

recorded event fastly.

■ PAUSE

To pause the playback of an

event;

To pause a live program.

■ NEXT

To go to the next event.

■ YELLOW

To group a list;

To select an EPG timer.

■ BLUE

To sort a list;

To zoom in/out the time slot of

the EPG view window.

■ FAV

To go to the favorite list of the

actual mode.

Familiarization

Section 4

EchoStar International Corporation Page 4 - 3

4

2. THE ECHONAV INSTALLATION MENU

A highlighted button shows you which (main/sub) menu is selected. The MENU key lets you

change between the main and sub-menu where thekeys let you make a selection in the

selected (main/sub) menu. The OK key brings you into the related page, where you can make

a choice from the available options.

■ The button, that gives you access to the User Preferences menu;

■ The button, that gives you access to the installation setup menu;

■ The button, that gives you access to the Conditional Access menu.

2.1. THE USER PREFERENCES MENU

■ The button, that gives you access to the User Profile page.

■ The button, that gives you access to the Languages page.

■ The button, that gives you access to the Parental Lock page.

■ The button, that gives you access to the Local Time page.

■ The button, that gives you access to the TV System page.

2.1.1. USER PROFILE SUB-MENU

This sub-menu allows you to customize the user profile settings, you can customize:

NOTE

Once in a page, at any time:

■ you can use the MENU key to reverse from a menu page to the sub-menu bar;

■ you can easily leave with the EXIT key.

This main menu has different sub-menus that give

access to the pages where you can customize the

factory settings.

The user preferences menu always comes in view with

the User Profile sub-menu. In the menu bar the

sub menus are shown at the right side. The available

sub menus are shown as icons which become a

highlighted button after selection.

The sub-menus are accessible with:

■ Aspect ratio

To set the screen size of the TV.

■ InfoBanner time-out

To select the view time for the InfoBanner.

■ Dolby Digital

To tell the receiver that it is connected to a Dolby

Digital amplifier or not.

■ RGB-Sync

To switch the RGB-sync signal, which is required by

monitors only, to On (monitor) or Off (TV).

■ Backgrounds

To select the standard or a personal background

color.

Section 4

Familiarization

Page 4 - 4 EchoNAV 2.2

2.1.2. LOCAL TIME SUB-MENU

This sub-menu allows you to customize the local time settings. For the correct operation of

the EPG and the timers, it is necessary to set the local time correctly. You can customize:

2.2. THE INSTALLATION SETUP MENU

■ The button, that gives you access to the System Setup page (for Fixed dish, SMATV);

■ The button, that gives you access to the System Setup page (for motorized dish);

■ The button, that gives you access to the Program Satellites page (for motorized dish);

■ The button, that gives you access to the User LNB Setting page (For Advanced only);

■ The button, that gives you access to the Set East/West Limit page;

■ The button, that gives you access to the About EchoStar information page;

■ The button, that gives you access to the System Upgrade page;

■ The button, that gives you access to the Factory Reset page.

■ Year

To set the actual year.

■ Month

To set the actual month.

■ Date

To set the actual date.

■ Day

To set the actual day.

■ Hour

To set the actual time in hours.

■ Minute

To set the actual time in minutes.

■ Save settings

To confirm the settings you made.

This main menu has different sub-menus that give

access to the pages where you can customize the

settings to match your personal requirements.

Note that the sub-menus are dynamic which means that

they change with the selections you make.

The installation setup menu always comes in view with

the system setup sub-menu. In the menu bar the

sub menus are shown at the right side. The available

sub menus are shown as icons which become a

highlighted button after selection. The sub-menus are

accessible with:

Familiarization

Section 4

EchoStar International Corporation Page 4 - 5

4

2.2.1. SYSTEM SETUP SUB-MENU - EASY

DVR-7000 HDD

ONLY

This sub-menu allows you to customize the system setup to match your installation. Note that

the menu page is dynamic which means that it changes with the selections you make. You

can customize:

■ System

To select the dish type you use.

■ Installation (fixed, motorized only)

To select the guided setup procedure for Easy

installations or Advanced installations with multiple

user defined LNBs.

■ LNBs

To set the amount of LNBs you have installed.

■ Polarity

To set the device that controls the signal polarity.

■ Switch

To set the switch type which you use to control the

dish installation (if used).

■ LNB1

To set the LNB type(s) you use.

■ SAT (for fixed only)

To select the satellite you want to scan for the LNB.

Satellite S00 brings you to the add data menu.

■ Method (for motorized only)

To set the channel search method;

AutoSat (automatically calculate the satellite

positions from reference positions)

Manual (enter the satellites by manual search).

■ AutoSat (for motorized, AutoSat only)

To confirm the selections you made and advance to

the AutoSat setup page (AutoSat only)

■ Set limits (for motorized, manual only)

To confirm the selections you made and advance to

the Set limits page.

■ Check signal (for fixed only)

To confirm the selections you made and advance to

the Check signal page.

■ Symbol rate1-4 (for SMATV only)

To set the symbol rate you want to scan.

■ Search channels (for SMATV only)

To confirm the selections you made and advance to

the Search channels page.

Section 4

Familiarization

Page 4 - 6 EchoNAV 2.2

DVR-5000 HDD ONLY

This sub-menu allows you to customize the system setup to match your installation. Note that

the menu page is dynamic which means that it changes with the selections you make. You

can customize:

■ System

To select the dish type you use.

■ Installation (fixed, DiSEqC 1.2 only)

To select the guided setup procedure for Easy

installations or Advanced installations with multiple

user defined LNBs.

■ LNBs

To set the amount of LNBs you have installed.

■ Polarity

To set the device that controls the signal polarity.

■ Switch

To set the switch type which you use to control the

dish installation (if used).

■ LNB1

To set the LNB type(s) you use.

■ Program Satellites (DiSEqC1.2 only)

To confirm the selections and go to next menu.

■ SAT (for fixed only)

To select the satellite you want to scan for the LNB.

Satellite S00 brings you to the add data menu.

■ Check signal (for fixed only)

To confirm the selections you made and advance to

the Check signal page.

■ Symbol rate1-4 (for SMATV only)

To set the symbol rate you want to scan.

■ Search channels (for SMATV only)

To confirm the selections you made and advance to

the Search channels page.

Page is loading ...

EchoStar DVR-7000 HDD Viaccess Supplementary Manual

This manual is also suitable for

EchoStar DVR-7000 HDD Viaccess Supplementary Manual

Related papers

Other documents