2. Pioneer Industries
  3. 2AM600

Pioneer Industries 2AM600 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Pioneer Industries 2AM600 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Installation Guide
Wallmount Pot Filler:
2AM600•
2MT600•
This product meets the following standards:
ASME A112.18.1 •
ANSI A117.1 •
ANSI / NSF 61, SECTION 9 •
CUPC / IAPMO LISTED / ADA COMPLIANT•
CONTAINS NO MORE THAN 0.25% WEIGHTED •
AVERAGE LEAD CONTENT
REV-10 31, 12
Engineering Excellence
Pioneer Industries, Inc. © 2012
Engineering Excellence
Engineering E xcellence
2
REV-10 31, 12
Thank you for purchasing this Pioneer quality product.
Tools Required
Adjustable
Wrench
TeonTape Rags 3/32” Allen
Wrench
1/16” Allen
Wrench
Prior to Installation
Observe all local plumbing and building codes before you begin •
installation.
Carefully shut off cold water supply. •
Plug the sink drain with a soft cloth to prevent intrusion of debris or the •
loss of any parts.
Pioneer reserves the right to make changes in the design of faucets •
without notice.
3
REV-10 31, 12
Faucet Installation
Caution:- Do not hold both swivel arms to avoid any damage when install •
thepot-llertoinletpipenipple.
Ensure the 1/2” IPS/NPT threaded inlet is installed properly.1.
Conrmthe1/2”IPS/NPTthreadedinletpipenipplemustbekeptwitha2.
lengthof1/2”fromthenishedwall.
Afterwallisnishedinstallthepotllertothe1/2”IPS/NPTthreaded3.
inlet pipe nipple. Do not fully tighten.
Levelthepot-ller.Markthedrillingholelocationonthenishedwall.4.
Removethepotller.5.
Drill the four 3/32” holes on the premarked location.6.
4
REV-10 31, 12
Faucet Installation
7. Applyteontapebeforeinstallingthemountingbracket(B).Putthe
mounting washer on the wall and drill the 3/32” hole on the same loca-
tionaswall.Ensurethemountingwasher(A)isbehindthemounting
bracket(B)toformthewatertightseal.Installthemountingbracket(B)
withthemountingscrews(C)suppliedwithfaucet.Tightenthemounting
screws(C).
8. Removethe3/32”allenscrew(D).
9. Carefullyscrewthepot-llerintoinletpipenippleusingstrapwrenchto
fullytightenthepotller.Ensurethenotchesonthefaucetalignwiththe
3/32”allenscrew(D).
10. Levelthepotller.
11. Tightenthe3/32”allenscrew(D).
12. Place the escutcheon in correct position. Tighten the 1/16” allen
screw(E).
5
REV-10 31, 12
Faucet Installation
13. Makesurethepotllerspoutswivelssmoothly.
14. Placeabucketunderneathofthepot-ller.Removetheaerator.
15. Turn on inlet water supply. Make sure all the connections are secure.
Openbothhandles.Flushandallowwatertorunatfullowforatleast
one minute. Replace the aerator.
16. Turn off water.
For more care information or trouble shooting inquiries about your
Pioneer Product, please see the contact information on the back page.
6
REV-10 31, 12
3325S.GareldAve.|Commerce,CA90040
Telephone:(800)338-9468|(323)888-8873|Fax:(323)888-9515
Hours: M - F, 7:30am to 5:00pm PST
www.pioneerind.com
Engineering Excellence
Engineering E xcellence
/