Pioneer Faucets 3DM100 Installation guide

Pioneer Faucets
Brand
Pioneer Faucets
Model
3DM100
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Pioneer Faucets 3DM100-BN is a high-quality lavatory faucet that meets the following standards: ASME A112.18.1, ANSI A117.1, ANSI / NSF 61, SECTION 9, CUPC / IAPMO LISTED / *ADA COMPLIANT, and contains no more than 0.25% weighted average lead content. This versatile faucet is designed for both residential and commercial use and is perfect for any bathroom. With its durable construction and stylish design, the Pioneer Faucets 3DM100-BN is a great choice for anyone looking for a high-quality, long-lasting faucet.

Pioneer Faucets 3DM100-BN is a high-quality lavatory faucet that meets the following standards: ASME A112.18.1, ANSI A117.1, ANSI / NSF 61, SECTION 9, CUPC / IAPMO LISTED / *ADA COMPLIANT, and contains no more than 0.25% weighted average lead content. This versatile faucet is designed for both residential and commercial use and is perfect for any bathroom. With its durable construction and stylish design, the Pioneer Faucets 3DM100-BN is a great choice for anyone looking for a high-quality, long-lasting faucet.

Installation Guide
Two Handle Lavatory Faucet:
3DM100•
3DM101•
3BL100•
3BL101•
3GB100 •
This product meets the following standards:
ASME A112.18.1 •
ANSI A117.1 •
ANSI / NSF 61, SECTION 9 •
CUPC / IAPMO LISTED / *ADA COMPLIANT•
CONTAINS NO MORE THAN 0.25% WEIGHTED •
AVERAGE LEAD CONTENT
REV-01 14, 13
Engineering Excellence
Pioneer Industries, Inc. © 2012
Engineering Excellence
Engineering E xcellence
2
REV-01 14, 13
Thank you for purchasing this Pioneer quality product.
Tools Required
Adjustable
Wrench
TeonTape Rags 3/32” Allen
Wrench
Prior to Installation
Observe all local plumbing and building codes before you begin •
installation.
Carefully shut off both hot and cold water supplies from under the sink. •
Plug the sink drain with a soft cloth to prevent intrusion of debris or the •
loss of any faucet parts.
For replacement installations, carefully remove the existing •
faucet and clean the entire surface of the sink mounting holes.
Pioneer reserves the right to make changes in the design of faucets without •
noticeasspeciedinthepricebook.
3
REV-01 14, 13
Faucet Installation
Clean lavatory surface (A) from oil, grease or debris.•
Apply adequate amount of plumbers putty or sealant underneath of base •
plate.
Lead the faucet shank (B) through faucet holes. •
Slide the mounting washers (c) through faucet shank (B). •
Thread and hand tighten the mounting nut (D) through faucet shank (B). •
Make sure both side of mounting nuts (D) are securely tighten.
4
REV-01 14, 13
Pop-up Drain Installation
Removethepop-upstopper(E)andpop-upange(F)fromthepop-up1.
assembly.
Applyadequateamountofplumbersputtyundersideofpop-upange(F)2.
then insert pop-up drain assembly from underside of the sink and secure
thepop-upange(F)fromthetop.
Rotate the drain body so that horizontal rod hole faces back of the fau-3.
cet.Hold the pop-up assembly in place and tighten the locknut (G).
Remove the excess putty. Connect the trap (H) (check manufacturer’s 4.
instructions for installation).
Remove rod nut (I).5.
Ensure the washer (K) is in place (for brass pop-up only). Insert rod (J). 6.
Tighten the rod nut (I).
Push rod down to open drain. Insert the pop-up stopper (E) carefully. 7.
Test if the pop-up stopper (E) is working properly.
Connect pop-up bracket to the rod using clip (L). Tighten the thumb-8.
screw (M) to connect pop-up bracket to pop-up lift rod.
5
REV-01 14, 13
Pop-up Drain Installation
6
REV-01 14, 13
Grid Drain Installation
Remove the grid trim ring (N) from the grid drain assembly (O).1.
Apply adequate amount of plumbers putty underside of the grid trim ring 2.
(N). Attach the grid trim ring (N) from top of the drain hole. Insert the grid
drain assembly (O) from under the lavatory sink.
Hold the grid trim ring (N) in place while threading the locknut (P) until 3.
the locknut is snug with the underside of lavatory sink.
Tighten the locknut (P).4.
Remove the excess putty. Connect the trap (H) (check manufacturer’s 5.
instructions for installation).
7
REV-01 14, 13
Main Supply Connection
Connect the faucet shank to inlet supply lines (Q). Connect the supply •
stops (R) to the inlet supply lines (Q) (left is hot water supply and right
is cold water supply). Make sure inlet supply lines (Q) are securely
tighten. Do not overtighten.
Turn on water. Check for any leaks. Make sure all the connections are •
secure.
Remove aerator (S).•
Open the handle.•
Flushandallowwatertorunatfullowforatleastoneminute.•
Replace aerator (S).•
For more care information or trouble shooting inquiries about your
Pioneer Product, please see the contact information on the back page.
8
REV-01 14, 13
3325S.GareldAve.|Commerce,CA90040
Telephone:(800)338-9468|(323)888-8873|Fax:(323)888-9515
Hours: M - F, 7:30am to 5:00pm PST
www.pioneerind.com
Engineering Excellence
Engineering E xcellence
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Pioneer Faucets 3DM100 Installation guide

Pioneer Faucets
Brand
Pioneer Faucets
Model
3DM100
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for

Pioneer Faucets 3DM100-BN is a high-quality lavatory faucet that meets the following standards: ASME A112.18.1, ANSI A117.1, ANSI / NSF 61, SECTION 9, CUPC / IAPMO LISTED / *ADA COMPLIANT, and contains no more than 0.25% weighted average lead content. This versatile faucet is designed for both residential and commercial use and is perfect for any bathroom. With its durable construction and stylish design, the Pioneer Faucets 3DM100-BN is a great choice for anyone looking for a high-quality, long-lasting faucet.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents