PAC BKNDK739 is a vehicle-specific dash kit that allows you to replace your factory radio with an aftermarket unit in select Nissan, Suzuki, and Infiniti vehicles. It provides a seamless fit and finish, matching the look and feel of your vehicle's interior. With this kit, you can upgrade your audio system while maintaining a factory-like appearance.
PAC BKNDK739 is a vehicle-specific dash kit that allows you to replace your factory radio with an aftermarket unit in select Nissan, Suzuki, and Infiniti vehicles. It provides a seamless fit and finish, matching the look and feel of your vehicle's interior. With this kit, you can upgrade your audio system while maintaining a factory-like appearance.
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
Nissan
2009-11 FRONTIER
2009-11 XTERRA
Suzuki
2009-11 EQUATOR
VEHICLE APPLICATIONS
NDK739 Mounting Kit
iNDK739
2500 East Francis Street Ontario, CA 91761, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006
For information about other American International automotive
accessories visit our website at:
http://www.aius.net
©2015 AMERICAN INTERNATIONAL INDUSTRIES, INC.
TECH Ver. 4/11 PRINT Ver. 5/15
1 6
1. Carefully pry the small tray located above the radio upward and remove.
2. Remove the (3) Phillips screws securing the Radio/Climate control/Vent assembly to
the sub-dash.
3. Carefully pull the entire assembly forward and unclip the lower edge of the entire
Radio assembly, disconnect all attached harnesses and antenna lead and remove
Radio assembly.
DASH DISASSEMBLY AND RADIO REMOVAL INSTRUCTIONS
2
009-11 NISSAN FRONTIER
2009-11 NISSAN XTERRA
2009-11 SUZUKI EQUATOR
1. Remove the (10) T-15 Torx screws securing the factory radio to the back side of the
Radio/Climate control Bezel assembly.
2. Remove the (4) T-10 Torx screws securing the Climate control module to the back side
of the Radio/Climate control Bezel assembly.
FACTORY RADIO AND CLIMATE CONTROL REMOVAL INSTRUCTIONS
1. Install the Climate Control module to the back of the ND-K739 kit using the same
(4) T-10 Torx screws removed from the factory Bexel.
2. See pages 2-4 for kit assembly & radio installation instructions for the type of radio
you are installing.
3. Insert the assembled ND-K739 kit into the back of the factory Bezel using
the (10) T-15 Torx screws removed from the factory Bexel.
KIT PREPARATION
NOTES
5 2
Single DIN Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B page 3.
2. Insert pocket (part # POC-739) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the upper section of the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
6. Install radio into sleeve and lock into place.
7. Attach a rear support bracket to the rear of the new
radio and adjust as necessary to attach to the rear
support stud located on the back of the pocket
using the small phillips screw supplied with kit.
KIT ASSEMBLY INSTRUCTIONS
Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket. See Figure B page 3.
2. Insert pocket (part # POC-739) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of upper section on both Left & Right mounting
brackets as shown in Fig. A. (See Figure A page 3)
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
6. Slide radio component forward or backward for desired look and tighten screws.
7. Attach a rear support bracket to the rear of the new radio a.d adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit.
KIT ASSEMBLY INSTRUCTIONS
DI
N S
l
e
eve
NOTE: ISO trim ring (ITR-739) may be used in
place of after-market radio’s removable trim ring.
NOTES
3 4
NOTE: #1 - ISO trim ring (DITR-739) must be used in place of after-market radio’s trim rings. For ISO mount
applications, mount after-market radio components to side brackets using screws provided with
radio when possible or hardware included with kit.
For ISO mount only: Attach (1) ISO Spacer to the
inside of upper sections on both Left
& Right mounting brackets as shown in Fig. A.
Cut
Cut
Left
Right
Fig. A
DITR-739
Double DIN & Double ISO Mount Applications
1. Attach the left and right side brackets to the main frame. (See figure below)
2. For double DIN radio applications ONLY cut and remove center rib from DITR-739 and file edges smooth.
3. Follow steps 4-6 from single ISO instructions on page 2.
4. Attach a rear support bracket to the rear of the radio components and adjust as needed to allow rear support
bracket to rest in the sub-dash.
KIT ASSEMBLY INSTRUCTIONS
IMB-739L
IMB-739R
Fig. B
Main Frame
NOTE: #1 - ISO trim ring (ITR-739) may be used in place of after-market radio’s removable trim ring.
#2 - Spacers must read upright (This side up for single ISO install).
IT
R-7
3
9
(
To
p
)
For ISO mount only: Attach (1) ISO
Spacer to the inside of upper section
on both Left & Right mounting
brackets as shown in
Fig. A.
Left
POC-
7
3
9
IMB-739L
IMB-739R
Right
Fig. A
Fig. B
Ma
in
F
ra
m
e
Single ISO Mount Applications Cont.
KIT ASSEMBLY INSTRUCTIONS
-
1
-
2
-
3
-
4
PAC BKNDK739 is a vehicle-specific dash kit that allows you to replace your factory radio with an aftermarket unit in select Nissan, Suzuki, and Infiniti vehicles. It provides a seamless fit and finish, matching the look and feel of your vehicle's interior. With this kit, you can upgrade your audio system while maintaining a factory-like appearance.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
American International TOYK994 User manual
-
American International LXSK1315 User manual
-
American International NDK746 Owner's manual
-
American International GMK325BM User manual
-
American International HYNK1133 User manual
-
Metra 99-7001 Installation guide
-
ACV 381210-16-1 Installation guide
-
Metra Electronics 99-7581 User manual
-
Metra 99-7417 Installation guide
-
Metra Electronics 99-7431 Installation Instructions Manual
