PAC MAZK847 User manual

PAC
Brand
PAC
Model
MAZK847
Category
Car kits
Type
User manual

This manual is also suitable for

PAC MAZK847 is a versatile automotive accessory designed to enhance the functionality and aesthetics of your Mazda CX-7. With this kit, you'll have the ability to seamlessly integrate aftermarket radios and other accessories into your vehicle's dashboard, providing a professional and cohesive look. The kit's modular design allows for flexible configurations, accommodating both single-DIN and double-DIN head units, as well as single-ISO and double-ISO mount applications.

PAC MAZK847 is a versatile automotive accessory designed to enhance the functionality and aesthetics of your Mazda CX-7. With this kit, you'll have the ability to seamlessly integrate aftermarket radios and other accessories into your vehicle's dashboard, providing a professional and cohesive look. The kit's modular design allows for flexible configurations, accommodating both single-DIN and double-DIN head units, as well as single-ISO and double-ISO mount applications.

CUSTOMER HELP LINE
8am-4:30 P.S.T. Monday-Friday Except Holidays
USA 800-323-4329 • Canada 800-245-8777
Mazda
2007-09 CX-7
VEHICLE APPLICATIONS
MAZK847 Mounting Kit
iMAZK847
Automotive Products Division
1040 Avenida Acaso • Camarillo, CA 93012, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006 • USA Fax (805) 388-7950
For information about other American International automotive
accessories visit our website at:
http://www.americaninternational.net
©2012 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH Ver. 12/12 PRINT Ver. 12/12
2 7
1. Carefully pull forward and remove the entire trim bezel from around the radio
and Climate controls.
2. Remove the (4) Phillips screws securing the radio to the sub-dash,
disconnect all attached harnesses and antenna lead and remove radio.
Hazard Switch Removal Instructions
1. Disconnect the harness attached to the back of the factory hazard switch.
2. Remove the (2) Phillips screws securing the Hazard switch to the rear
of the factory radio.
3. Remove the (4) Phillips screws securing the chassis of the factory radio
to the rear of the radio face and set aside the chassis.
4. Using a pick tool, or a jewelers flat blade screwdriver, carefully lift upward the back
top and bottom edge locking tabs securing the front portion of the Hazard button to
the rear section of the Hazard switch, and separate the 2 pieces and remove switch
from the face of the factory radio.
Hazard Switch Installation Instructions
1. Place the front Hazard switch into the position on the installation kit and insert the
back section of the Hazard switch from the rear and lock the 2 pieces together.
2. Secure the back of the hazard switch to the rear of the kit using the Phillips screws
removed in step 2 of Hazard switch removal instructions.
DASH DISASSEMBLY AND RADIO REMOVAL INSTRUCTIONS
2
007-08 MAZDA CX-7
Single DIN Mount Applications
1. Attach the left and right side brackets to the main bracket. (See Figure D pg. 4)
2. Insert pocket (part # POC847) into upper section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the lower section of the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
6. Install radio into sleeve and lock into place.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary
to attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit.
NOTE:
ISO trim ring (ITR847) may be used in place of after-market radio’s removable trim ring.
KIT ASSEMBLY INSTRUCTIONS
Main Frame
DIN Sleeve
NOTES
POC847
Fig. B
ITR847
4 5
NOTES
NOTE: #1 - ISO trim ring (DITR847) must be used in place of after-market radio’s trim rings. For ISO mount
applications, mount after-market radio components to side brackets using screws provided with
radio when possible or hardware included with kit.
For ISO mount only: Attach (1) ISO Spacer to the
inside of upper sections on both Left & Right
mounting brackets as shown in Fig. A.
Cut
Cut
Left
Right
Fig. A
DITR847
Double DIN Mount Applications
1. Attach the left and right side brackets to the main frame. See figure D below.
2. For double DIN radio applications cut and remove center rib from main frame and file edges smooth.
3. Follow steps 4-6 from single ISO instructions on page 3.
4. Attach a rear support bracket to the rear of the radio components and adjust as needed to allow
rear support bracket to rest in the sub-dash.
KIT ASSEMBLY INSTRUCTIONS
IMB847L
IMB847R
Fig. D
Main Frame
Remove
Shaded Tabs
6 3
Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket.
2. Insert pocket (part # POC847) into upper section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of lower section on both Left & Right mounting
brackets as shown in Fig. A below)
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
6. Slide radio component forward or backward for desired look and tighten screws.
7. Attach a rear support bracket to the rear of the new radio a.d adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit.
KIT ASSEMBLY INSTRUCTIONS
NOTE: #1 - ISO trim ring (ITR847) may be used in place of after-market radio’s removable trim ring.
Some radio faces may be too large & require filing of trim ring.
ITR847
(Top)
For ISO mount only: Attach (1) ISO
Spacer to the inside of upper section on
both Left & Right mounting
brackets as shown in
Fig. A.
POC847
IMB847L
IMB847R
Fig. A
Fig. C
Main Frame
Single ISO Mount Applications Cont.
NOTES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

PAC MAZK847 User manual

PAC
Brand
PAC
Model
MAZK847
Category
Car kits
Type
User manual
This manual is also suitable for

PAC MAZK847 is a versatile automotive accessory designed to enhance the functionality and aesthetics of your Mazda CX-7. With this kit, you'll have the ability to seamlessly integrate aftermarket radios and other accessories into your vehicle's dashboard, providing a professional and cohesive look. The kit's modular design allows for flexible configurations, accommodating both single-DIN and double-DIN head units, as well as single-ISO and double-ISO mount applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents