Mamas & Papas pliko pramette Instructions For Use Manual

Brand: Mamas & Papas

Model: pliko pramette

Type: Instructions For Use Manual

Instructions for use

pliko pramette

- 2 -

CONTENTS LIST

PLIKO PRAMETTE PUSHCHAIR

Dear Customer,

Thank you for choosing the Mamas & Papas Pramette Pushchair.

The stylish, lightweight and compact folding Pramette Pushchair is easily converted from a pram

into a pushchair so as your child grows and develops so does your pushchair.

The Mamas & Papas Primo Viaggio Car Seat and Mypod / Navetta Carrycot can also be attached to

the pushchair using the Surex ‘right rst time’ attachment system.

Opening the pushchair .............................................................................................................5

Attaching the wheels ................................................................................................................6

Attaching rear wheels to the frame ......................................................................................7

Fitting extending & Removing the bumper bar ..................................................................8

Fitting & Removing the basket ...............................................................................................9

Attaching the cup holder .........................................................................................................9

Adjusting the handle length ....................................................................................................10

Adjusting the backrest .............................................................................................................10

Operating the adjustable leg rest ..........................................................................................11

Operating the swivel wheels ..................................................................................................12

Operating the brakes ...............................................................................................................13

Using the ride-on plate ............................................................................................................13

Attaching the hood ...................................................................................................................14

Removing the hood ..................................................................................................................14

Attaching the Apron .................................................................................................................15

Using the harness ......................................................................................................................16

Folding the pushchair ...............................................................................................................17

Using the pushchair as a pram ...............................................................................................18

Fitting the Primo Viaggio Car seat .........................................................................................20

Attaching the raincover to the pushchair ............................................................................22

Attaching the raincover to the pram ....................................................................................23

Removing the fabric cover ......................................................................................................24

Care and maintenance .............................................................................................................26

- 3 -

PRODUCT INFORMATION

ACCESSORIES

This pushchair has been designed and tested to comply with the latest British

and European safety standards.

Important: Read these instructions carefully and keep them

for future reference. Your child’s safety may be affected if you

do not follow the instructions.

• This pushchair is designed for children from birth to 15kg

- 3 years. Please note: All children grow at different rates so the

age given is an approximation only.

• The pushchair can be simply converted into a pram.

• The Primo Viaggio Car Seat can be attached to the pushchair.

• The pushchair comes equipped with a ﬁve-point harness. Always use

the harness when your child is in the seat unit.

• The suspension on all four wheels gives your child a comfortable

ride.

• A footrest that can be adjusted to two positions.

• A backrest that can be adjusted to four positions.

• A shower resistant removable fabric hood.

• Adjustable handle length for added comfort.

• Lockable swivel wheels for easy manoeuvring.

• An opening / removable bumper bar.

• A removable shopping basket.

• The pushchair is free standing once it has been folded.

• PVC Raincover

The Mamas & Papas range of co-ordinating pram and pushchair accessories are available.

This range includes bags, footmuffs, sun canopies, raincovers, pram bedding & mattresses. Also

included are pram toys.

- 4 -

INSTRUCTIONS FOR SAFE USE

• WARNING: A CHILD’S SAFETY IS YOUR RESPONSIBILITY.

• WARNING: IT MAY BE DANGEROUS TO LEAVE YOUR CHILD

UNATTENDED.

• THIS PRODUCT IS NOT SUITABLE FOR RUNNING OR SKATING.

• WARNING: ANY LOAD ATTACHED TO THE HANDLES AFFECTS THE

STABILITY OF THE PRAM/PUSHCHAIR.

• Always ensure that your pushchair is fully erect and all locking clips are engaged. (Take

particular care if the PVC Raincover is ﬁtted. Check that it is not entangled or preventing

the locking mechanism from functioning correctly).

• Your pushchair is supplied with a ﬁve-point body harness. Children should be harnessed

in at all times. Ensure that the harness is correctly adjusted, providing a snug ﬁt around

your child. Adjustments can be made using the buckles on the shoulder, waist and crotch

straps. Please refer to the “Using & adjusting the harness” page16. The pushchair is supplied

with ‘D’ ring harness attachment points. These are located on either side at the base of

the backrest and are for ﬁtting a separate harness conforming to BS 6684 if required. We

recommend that an additional harness is used when the pushchair is used as a pram.

• Always ensure the brakes are correctly engaged whenever the pushchair is left for any

reason, even if only for a short time on a ﬂat surface.

• Care should be taken when using any PVC cover. Regularly check that your child is

comfortable and not over heating. There are mesh ventilation panels on the sides of the

cover. These are essential to aid the ﬂow of cool air around your baby. Unless it is raining,

the raincover should either be removed or the top section opened, see ‘Attaching the

Coperto Raincover’ sections on pages 22.

• Always ensure your child is clear of moving parts before you adjust the position of the

backrest, footrest or canopy.

• Always manoeuvre your pushchair up and down kerbs and steps gently. Do not let your

pushchair drop. Carry it up stairs whenever possible.

• Never overload your pushchair with additional goods.

• Do not hang shopping from the handles. Do not use any replacement parts or accessories

e.g. child seats, rain covers, stand-on platforms etc, except those recommended or supplied

by Mamas & Papas. The use of non-approved replacement parts or accessories may damage

or make your pushchair unsafe.

• Never force your pushchair. Adjustments and locks should be free and easy to operate.

• Do not store your pushchair in a damp place. Always allow the fabric to dry naturally away

from direct heat.

• The basket supplied with your pushchair is designed to hold a maximum of 3kg. Excessive

weight could damage the basket or impede the safe operation of the pushchair.

• We recommend that you ﬁt a Mamas & Papas parasol to shade your child from direct

sunlight. We recommend that this is used in conjunction with the appropriate sun

protection cream and clothing.

- 5 -

OPENING THE PUSHCHAIR

Remove the protective caps

from the ends of the handle

frame.

Never attempt to use the

pushchair with the covers ﬁtted

as the locks will not engage.

Release the ﬁnger catches

located under both of the

handles by pulling them

upwards.

Lift the pushchair upwards and

the frame will automatically

start to open.

You may need to press down

lightly on the seat to ensure

the safety locks have engaged.

There are two safety locks, one

on each side of the pushchair.

Ensure the closing handle in

the centre of the pushchair’s

back is pushed down as far as

possible by gently pushing the

lever plates at the back fully

down.

Warning: Ensure that all

locking devices are engaged

before use.

- 6 -

ATTACHING THE WHEELS

Attaching the front wheels:

Slot the two front wheels onto

the ends of the pushchairs

front legs.

Push the wheel housing onto

the end of the leg until it locks

into position.

Always check that the

wheels are correctly ﬁtted by

attempting to pull them off

again.

Attaching the back wheels:

Slot the rear wheels onto the

back legs of the pushchair.

Ensure that the brake peddles

on the wheels are facing out

from the back of the pushchair.

Push the wheels down as far as

they will go.

Check that the pins in the

pushchairs legs are protruding

through the wheel housings.

Check the wheels are correctly

ﬁtted by trying to pull them off

again.

- 7 -

ATTACHING REAR WHEELS TO THE FRAME

Align the insert on the back

wheels with the bottom of the

back frame on the pushchair

(1).

Align the end of the insert

with the moulding on the back

frame (2).

Slide the insert into the

moulding (3).

Ensure the inset is fully

inserted into the moulding (4).

- 8 -

FITTING EXTENDING & REMOVING THE BUMPER BAR

Push the catches on the under

side of the armrests upwards

and slide the covers out of the

armrests.

Fitting the bumper bar:

Slide the ends of the bumper

bar into the holes in the ends

of the armrests.

Push the bumper bar inwards

until it clicks into place.

Push the two catches on the

underside of the armrest

inwards and slide the bumper

bar fully in.

To extend the bumper

bar: Push the catches on the

underside of the armrests

inwards and slide the bumper bar

outwards until it locks in place.

To remover the bumper

bar: Push the catches under the

armrests inwards and slide the

bumper bar out of the armrests.

When removing the bumper

bar, insert the plugs provided

to close the armrests of the

chassis.

WARNING: Always fit the

covers once the bumper bar is

removed.

- 9 -

FITTING & REMOVING THE BASKET

The back section of the

basket has four webbing loops

that ﬁt over the four hooks

attached to the back legs of the

pushchair.

The two front webbing loops

ﬁt over the hooks on the font

legs of the pushchair.

The hooks are situated just

below the frame locks on

either side of the frame.

We recommend that you do

not exceed a load of 3kg in the

basket. Excessive weight could

damaged the basket.

Slot the lug just above folded

frame lock into the recess in

the top of the cup holder.

Push the top of the cup holder

downwards until it locks over

the lug.

Check that the cup holder

is correctly attached by

attempting to pull it of again.

Warning: It is dangerous to

place hot drinks in the cup

holder. Never hang additional

items on the cup holder.

- 10 -

ADJUSTING THE HANDLE LENGTH

ADJUSTING THE BACKREST

To lengthen the handle:

Push the top of the button in

just below the hand-grip and

pull towards you. Once the

handle has been adjusted it will

automatically lock into place.

The height of the two

handlebars can be adjusted to 3

positions.

To shorten the handle:

Press the bottom of the button

in and push the grip away from

you.

The backrest can be adjusted

to one of four positions.

To lower the backrest:

Pull the backrest adjustment

handle upwards and lower the

backrest into the position you

require. Release the handle and

move the backrest upwards or

downwards until it locks into

position.

To raise the backrest:

Grip the middle of the backrest

and lift upwards until it locks in

the position you require.

- 11 -

OPERATING THE ADJUSTABLE LEG REST

The leg rest on the front of the

pushchair can be adjusted for

the comfort of your child and

so that the Mypod / Navetta

Carrycot can be attached.

Note: The leg rest must be

in the most vertical (down)

position when the pushchair is

being used by a child that can

sit unaided and the backrest is

in an upright position.

Positions 1 & 2 are for general

use. Position 3 is only used

when the Mypod / Navetta

Carrycot is attached.

To adjust the leg rest, pull

the locks on both sides of

the leg rest in the direction

of the arrows in the diagram.

Now either lift or lower the

leg rest whilst releasing the

catches, the leg rest will lock

automatically into position.

- 12 -

OPERATING THE SWIVEL WHEELS

The front wheels on the

pushchair can be used in either

the ﬁxed or swivel mode.

Fixed mode:

Push the catches between the

front wheels upwards.

The wheels will now be ﬁxed

and will not swivel.

Swivel mode:

Push the catches between the

front wheels downwards.

The wheels can now be rotated

through 360º.

- 13 -

OPERATING THE BRAKES

USING THE RIDEON PLATE

To engage the brakes:

Press down on both ends

of the brake bar with your

toes. Check the brakes are

correctly engaged by rocking

the pushchair backwards and

forwards.

To release the brakes:

Push upwards on both ends of

the brake bar with your toes

until the pushchair’s wheels

move freely.

Warning: Always engage the

brakes when you leave or let go

of the pushchair for whatever

reason.

The rear ride-on plate can be

used for lifting the pushchair up

curbs and to carry an additional

child on.

The maximum weight for a

child on the ride-on plate is 20

kg (up to a maximum age of 4

years approximately).

Before using the ride-on plate

the hood must be removed

and the backrest raised to the

highest position.

Do not attempt to use the

ride-on plate with the backrest

lowered.

- 14 -

ATTACHING THE HOOD

REMOVING THE HOOD

To ﬁt the hood to the

pushchair:

Slot the tabs on the sides of the

hood into the slots in the sides

of the pushchairs armrests.

Fasten the press studs on the

side ﬂaps of the hood onto the

insides of the armrests.

Fasten the press studs on the

back of the hood onto the

studs on the seats backrest.

To remove the hood:

Undo all of the press studs on

the back and sides of the hood.

Push the tabs on the sides of

the hood inwards until they are

free of the armrests.

The hood can now be removed.

- 15 -

ATTACHING THE APRON

To attach the apron, ﬁrst push

the bottom part of the apron

under the bumper bar.

Fasten the zip on the bottom

edge of the apron to the zip on

the front edge of the footrest

cover.

Important: Always ensure

that the apron is fully zipped to

the footrest cover.

- 16 -

USING THE HARNESS

Assembling the harness:

Slot the tabs on the ends of

the shoulder straps onto the

tongues on the ends of the

waist straps (A) .

Locking the harness:

Lock the harness by pushing

the tongues on the ends of the

waist straps into the buckle

on the crotch strap (B). The

harness will automatically lock

when the tongues have been

fully pushed in.

Unlocking the harness:

Push the button in the middle

of the harness inwards (C) and

the tongues will slide out of the

buckle (D). Your child can now

be removed from the pushchair.

Adjusting the harness:

To tighten the waist straps, pull

both of the ends of the straps

outwards (E). The waist strap

can be tightened as far as the

stop (F). To loosen the waist

straps feed the ends of the

straps back though the buckles.

IMPORTANT: Every time

you place your child in the

pushchair or when you position

of the backrest always check

that the harness is correctly

ﬁtted and the shoulder

and waist strap buckles are

correctly adjusted and a snug ﬁt

around your child.

Warning: Always use the

crotch strap in conjunction

with the waist belt.

- 17 -

FOLDING THE PUSHCHAIR

Engage the brakes before

closing the pushchair.

Pull the left ﬁnger catch

upwards (1) until it locks into

position, then repeat for the

other ﬁnger catch (2).

Grip the handle in the centre

of the backrest and pull it

upwards (3) as shown in the

diagram.

Continue to pull the handle

upwards until the pushchair is

fully folded (4).

Ensure that the two locking

catches below the ﬁnger

catches lock over the clips

on the rear leg attachment

moulding, as shown in the

diagram.

WARNING: Do not push

down vertically on the frame

when folding. This will cause

the ends of the handles to hit

the ﬂoor and may damage the

frame.

- 18 -

USING THE PUSHCHAIR AS A PRAM

The pushchair can be

converted into a pram for

children from birth until the

child can sit up by itself or until

it reaches a weight of 9kgs.

Remove the hood and apron if

they are ﬁtted.

Raise the leg rest into its

highest position, see page 11.

Pull the bumper bar out to its

fully extended position, see

page 8.

Important: Ensure that

both ends of the bumper are

locked into the armrests when

extended. Never convert into a

pram with the bumper bar not

extended.

Unfasten the zip on the top of

the backrest.

Fold the cover down over the

front of the bumper bar.

Zip the top of the backrest

cover to the front of the

footrest cover.

Push the cover down onto the

seat.

Important: Always fully fasten

the backrest cover over the

bumper bar. Never use with the

cover partially attached.

- 19 -

Lower the backrest into the

lowest position, see page 10.

Lift the foot end of the pram

upwards from the seats

backrest.

To ﬁt the hood:

Attach the hood to the frame

on the opposite side to the

handles by pushing the hood

brackets into the arm rest slots

until they lock in place.

Fasten the studs on the back

of the hood to the studs on

the underside of the pushchair

footrest.

Attaching the apron:

Slot the apron over the

backrest of the pushchair.

Fasten the press studs on the

sides of the apron to the studs

on the sides of the pushchair.

Reverse the procedure to

convert the pram back into a

pushchair.

- 20 -

FITTING THE PRIMO VIAGGIO CAR SEAT

Apply the brakes on the

pushchair before operating the

attachment brackets.

Lower the backrest to its

lowest position by pulling

the lever at the top of the

backrest upwards, then lower

the backrest as far down as it

will go. Now raise the backrest

upwards one position.

In the corners of the seat unit

where the backrest joins the

seat base there are two ﬂaps.

Under the ﬂap are the

attachment brackets.

Pull the locks on the sides of

the frame outwards and hold.

Rotate the attachment brackets

upwards as far as they will go.

The attachment bracket will

lock in a vertical position.

Align the locking clip of the

car seat with the attachment

brackets of the pushchair.

Push the car seat down onto

the attachment brackets until it

clicks into place.

Check the car seat is ﬁrmly in

place by attempting to lift it

upwards.

Page is loading ...

Mamas & Papas pliko pramette Instructions For Use Manual

Mamas & Papas pliko pramette Instructions For Use Manual

Mamas & Papas pliko pramette Instructions For Use Manual

Related papers

Other documents