My Child Sienta Duo User manual

Brand: My Child

Model: Sienta Duo

Category: Strollers

Type: User manual

Sienta Duo

Tandem Pushchair

This product is tested to: BS EN 1888:2012

Front seat suitable from: 6 months up to 15kg

Rear seat suitable from: BIRTH up to 15kg

INSTRUCTIONS: Please read carefully and keep for future

reference. Your child’s safety may be affected if you do not

follow these instructions

V10

page 1

ATTENTION: This pushchair is designed to carry 1 child in the front seat and 1 child in the

rear seat. DO NOT carry more than 2 children in this pushchair.

WARNING! Never leave your child unattended.

WARNING! Ensure that all the locking devices are engaged before use.

WARNING! To avoid injury ensure that your child is kept away when folding and

unfolding this product.

WARNING! Do not let your child play with this product.

WARNING! The front seat unit is not suitable for children under 6 months.

WARNING! Always use the crotch strap in combination with the waist belt.

WARNING! Check that the pushchair body or seat unit attachment devices are

correctly engaged before use.

WARNING! This pushchair is not suitable for running or skating.

WARNING! Do not lift and carry the pushchair with a child in it.

WARNING! Do not use the pushchair on steep slopes, stairs, escalators, beaches, mud

etc.

WARNING! Use the D-rings provided for the attachment of a separate safety harness

approved to BS6684

WARNING! Ensure that children are clear of moving parts before making adjustments.

WARNING! Never leave raincovers, hoods and aprons on indoors and in hot weather.

WARNING! Do not use replacement parts or accessories other than those approved by

MyChild.

WARNING! Do not load the basket with a weight in excess of 2kg.

WARNING! Always apply the brakes when the pushchair is stationary, and when

placing and removing children.

WARNING! Taking children up or down stairs, escalators, steps, steep slopes and

muddy/rough terrain in a pushchair could be dangerous and should not be

attempted. Any resulting damage will not be covered under the warranty. Remove

your child from the pushchair and fold it up for easy carrying to negotiate such

hazards, or simply avoid them.

WARNING! If your pushchair is to be used by someone unfamiliar, e.g grandparents,

show them how it works before letting them use it.

WARNING! Hold onto your pushchair when close to moving vehicles and trains as the

draught from the vehicles may move the pushchair even with the brakes on.

Only use parts and accessories that are approved by the manufacturer or distributor.

Non-approved parts and accessories may be unsafe and must not be used and will

invalidate the warranty.

IMPORTANT - Read the instructions carefully before use and keep them for future

reference. Your child’s safety may be affected if you do not follow these instructions.

Safety instructions

Cautions

• Improper use or lack of knowledge regarding the instructions can result in

dangerous situations, personal injury or damage to the pushchair.

• Completely remove all plastic bags and packing materials before using this

product to prevent a possible chocking hazard.

• Use the pushchair at a normal walking speed only.

• Regular maintenance will increase the life cycle of the product.

page 2

Welcome

Thank you for purchasing the MyChild Sienta Duo Tandem Pushchair.

Please read the instructions and warnings carefully before use to ensure safe and

satisfactory operation of this product.

Your child’s safety is your responsibility. If you have a query with this product or require

replacement parts, please contact the MyChild Helpline on 0161 335 2508.

Layoutthepartsonasoftlevelsurfaceandcomparetothepart/ﬁxingschecklist

below. Do not discard any packaging until you are sure that you have all the parts.

WARNING! Assembly by an adult. Keep away from children until fully assembled. Keep

children clear during assembly as pack contains small parts which may present a

choking hazard.

Your 3 year warranty

Whilst we make and test our products to the highest standards of durability there’s

always a small chance of a hiccup! Our promise is to repair, replace or refund a

MyChildproductthathasanidentiﬁedmanufacturingdefectfromthedateof

purchase for a full 3 years thereafter at no extra cost.

However, you must register within 28 days of the date of purchase to receive the full 3

years guarantee!

To receive your full guarantee you can register your product by:

visiting www.mychild.co.uk/warranty.html and complete the warranty form,

or by telephone on 0161 335 2508.

• This product requires regular maintenance: Inspect the locking devices, brakes,

harnessassembly,catches,seatadjustments,jointsandﬁttingstoensuretheyare

secure and in full working order. Brakes and wheels are subject to wear and should

be replaced if necessary by contacting customer service.

• Ifanypartofyourpushchairbecomesstiffordifﬁculttooperate,ensurethatdirt

is not the cause. Use spray lubricant (silicone based) between the components.

Avoid over-spraying as this may encourage the accumulation of dirt. Regular

lubrication of moving parts will extend the life of your pushchair and make opening

and folding easier.

• The seat unit, plastic and metal parts must be sponged clean with warm water and

mild detergent. Always allow to dry thoroughly before using or storing.

• Do not leave the pushchair in sunlight for prolonged periods as fabrics may fade.

• Never use abrasives, ammonia, bleach or spirit based cleaners.

• Always store your pushchair in a dry place. Allow fabric and raincover to dry

thoroughly before folding and storing.

Care and maintenance

page 3

Parts checklist

Contained in your carton are:

NoPart Qty

1 Chassis 1

2 Front hood 1

3 Rear hood 1

4 Harness pads* 4

5 Basket* 1

6 Rear wheel assembly 1

7 Front wheels 2

8 Locking pin 1

9 Locking ring 1

10 Seat liner 1

11 Raincover 1

*Thesearepre-ﬁttedbutare

removable

10 11

6 7 8

page 4

1. Align the front wheel assembly with the

front axle, ensuring you have the spring

pin (A) on the rear of the axle aligned

with the small hole (B) on the rear of the

wheel assembly.

Push the front wheel assembly onto the

axle until you hear the spring pin ‘click’

into place.

NOTE: Check the wheel to make sure it is

secure by pulling it.

1. The swivel wheels can only be locked

when in the trailing position as shown.

To lock the wheel: position the wheel in

the trailing position and pull the swivel

lock up.

2. To allow the wheels to swivel: push

down on swivel lock (B).

WARNING: Always lock the swivel wheels when using the pushchair on rough surfaces.

Front wheel assembly

Using the swivel/lock function

click

page 5

1. Line up the rear wheel assembly with

the back legs of the pushchair, so that

the frame ‘LOCK’ (A) and the ‘BRAKE’

pedal (B) will be able to connect.

2. Push the wheel assembly onto the

back leg until the spring pins (C) click into

place.

3. Place the ‘BRAKE‘ pedal (D) into the slot on the frame ‘LOCK‘ (E).

4. Insert the locking pin (F) into the hole on the side of the frame ‘LOCK’ and push it all

the way through to connect the ‘BRAKE‘ pedal to the frame ‘LOCK’.

5. Thread the locking ring (G) through the hole on the end of the locking pin.

Rear wheel assembly

click

page 6

1. Hold the pushchair by the handles and

release storage strap (A). Whilst holding

the handles, allow the front legs to drop

towardstheoor.

3. Check that both the upper side hinges

engaged.

2. DO NOT try and open the pushchair by

forcing the handles apart. Place your foot

on the frame ‘LOCK’ pedal (B) and push

down until the frame is fully open and

locked.

Opening the pushchair

page 7

1. Place the toe of your shoe under the

bottom bar directly under the ‘BRAKE’

pedal and lift the bar up to release the

frame lock.

IMPORTANT: Lift the bar directly upwards

and not at an angle.

3. Gently push forwards until the

pushchair is folded.

4. Connect the storage strap (B).

2. Pull back both catches (A) on the

handles.

WARNING! Fold the rear hood back and the front hood forward before attempting to

fold the pushchair. Failure to do so may damage the hoods.

Folding the pushchair

page 8

Carrying the pushchair

Adjusting the rear backrest

1. Once you have attached the storage strap (A), carry the pushchair using the

integral carry handle (B) located on the side of the chassis.

1. To recline: Whilst pressing the button, on

the slider, downwards, pull the backrest

down into the required position

2. To raise: Push the slider up whilst holding

the strap.

page 9

Adjusting the front backrest

Using the brakes

WARNING: The brakes MUST always be ON when making adjustments, e.g. taking the

child out, putting the child in or letting go of the handlebars.

1. To engage the brakes, press down

on the brake lever and gently roll the

pushchair backwards and forwards.

Ensure both brakes have engaged before

letting go of the handles.

2. To disengage the brakes, place the

ball of your foot on the edge of the brake

pedal and push forward to release the

brake.

1. To lower the backrest on the front seat,

pull the lever on the back of the seat and

move the backrest backwards.

To raise the backrest, simply move the

backrest forward.

The front seat has 2 positions upright or

reclined.

page 10

Attaching/Using/Removing the rear hood

1. Slide the rear hood clips (A) onto the

attachment points (B) until they ‘click‘

into place.

2. Secure the hood fabric to the

pushchair using Velcro tabs (C1, C2, C3)

and Velcro strap (D1); repeat on opposite

side of hood.

C3 D1

Shopping basket

1. The basket is held in place with 6 press

studs (3 on each side). Wrap the straps

around the frame at points 1, 2 and 3 and

fasten the press studs.

page 11

Attaching/Using/Removing the front hood

Attaching/Using/Removing the rear hood (continued)

1. Hold the hood clip (A) at a slight angle

and slide it onto the attachment point (B)

until they ‘click’ into place

3. To open: pull the front of the hood

forwards, then press down on the hinges

(E) to lock the hood open.

To close: Lift the hinges and fold the hood

back.

2. To open: pull the front of the hood

forwards, then press down on the hinges

To close: Lift the hinges and fold the hood

back.

4. To remove: Unfasten all of the hood’s

Velcro tabs and Velcro straps.

Lift up the end of the clip and slide the

clip off the attachment.

A B

page 12

Using the harness

WARNING: Ensure harness is correctly tted at all times.

1.To lock: Clip the shoulder harness strap

clips (A) onto the loop of the waist strap

connectors (B).

Push the waist strap connectors (B) into

the buckle (C) until they CLICK into place.

Adjust the sliders on the waist and

shoulderstrapssothattheharnessﬁts

snugly.

2.To release: Squeeze the top and bottom

of the waist band connector (D). The

shoulder straps can be unclipped from the

waist straps if necessary (E).

Attaching/Using/Removing the front hood (continued)

3. To remove: Lift up the end of the clip

and slide the clip off the attachment.

page 13

Adjusting the rear seat shoulder harness position

1.The rear seat unit is suitable from birth.

There are 3 pairs of shoulder harness

positions (A1,2 & 3), two pairs of waist

harness positions (B1 & 2) and two crotch

strap positions (C1 & 2). Select the harness

positions that will allow you to adjust the

harness appropriately to suit your child’s

age and size.

2. To adjust the shoulder harness position,

release the harness as shown on page

12, ‘Using the harness’. Thread the strap

through the seat unit button hole so

it goes all the way to the rear of the

pushchair.

3. Reposition to desired height and thread

the strap back through the button hole

so it is back at the front of the pushchair.

Repeat the same actions for the other

shoulder strap, so both straps are at the

sameheight.Toensurethestrapisﬁtted

correctly and secure, pull the strap up

sharply.

WARNING: Do not let the shoulder strap

(grey) be threaded back over the top

of the of the pushchair seat cross bars

(black). The strap must be threaded

behind the cross bars.

ATTENTION: The shoulder straps can be

completely removed from the pushchair

when adjusting the position. Please

ensure it is secure before use.

page 14

Adjusting the rear seat waist harness position

1.Locate the split ring (A) for the waist harness at the back of the rear seat.

2. Remove the webbing (B) from the split ring.

3. With the webbing removed from the split ring, pass the waist strap (C) back through

the seat.

4. Reposition the waist strap by placing it back through one of the two waist strap slots

(D1 or D2).

5. Wrap the webbing back around the seat unit tube on the rear seat and place the

webbing back through the split ring (E).

ATTENTION: Ensure the straps are secure and properly adjusted to suit your child before

use.

To adjust the rear seat waist harness you will need to undo the webbing and pass it

through the seat, reposition it and reattach the webbing.

page 15

Adjusting the rear seat crotch harness position

1. To adjust the crotch strap position

closer to the child, slide the buckle under

the strip of fabric on the seat.

2. To adjust the crotch strap position

further from the child, slide the buckle out

from under the strip of fabric on the seat.

Fitting the seat liner

1. Toﬁttheseatlinerwhilsttheshoulder

straps on the pushchair are in the two

lowest positions:

Simply place the seat liner into the rear

seat and pull the harness straps around

the liner, ensuring the shoulder straps pass

through slots (A), the waist straps pass

through slots (B) and the crotch strap

passes through slot (C).

IMPORTANT: The seat liner may be used

only in the rear seat.

page 16

2.Toﬁttheseatlinerwhilsttheshoulder

straps on the pushchair are in the highest

position:

Unclip the shoulder straps (D) from the

waist connectors.

Fitting the seat liner (continued)

2a. Pass the shoulder straps through the

shoulder button holes (E).

Pull the waist and crotch straps around

the seat liner and reconnect the shoulder

harness strap clips (D) to the loop of the

waist strap connectors.

NOTE: For the baby’s comfort, always

make sure the harness height position on

the seat liner is the same as the height

position on the pushchair (either slot (A)

or button holes (E)).

page 17

Tips and advice

When mounting a kerb position a foot

against one of the rear wheels to act as

a pivot point, making it easier to tilt the

pushchair back before pushing it up the

kerb.

Fitting the raincover

1. Theraincoverﬁtsoverthefrontof

the tandem from the handlebars to the

footrest. It is held in place with Velcro

loops and strips around the frame.

ATTENTION: Allow raincover to dry before

storing.

[email protected]

Imported by MyChild. M34 3QA

www.mychild.co.uk

Tel: 0161 335 2508

My Child Sienta Duo User manual

Brand: My Child

Model: Sienta Duo

Category: Strollers

Type: User manual

Download PDF

report

My Child Sienta Duo User manual

My Child Sienta Duo User manual

Other documents