ADTRAN Total Access 1000 DSLAM ATM Dual T1 Job Aid

Brand: ADTRAN

Model: Total Access 1000 DSLAM ATM Dual T1

Type: Job Aid

TOTAL ACCESS

1000 DSLAM ATM DUAL T1/E1 LIU

JOBAID

T1/E1 LIU

1179010L1

LOOP 1

LOOP 2

DUAL T1/E1 LIU

CLEI: VACJC90C _ _

DESCRIPTION

The T1/E1 LIU is a common module designed for use in the Total Access 1000 DSLAM.

The T1/E1 LIU features:

■ Provides up to two T1/E1 interfaces ■ Local, Payload, and Network loopbacks

■ SF and ESF data framing formats ■ FAS and FAS+CRC framing for E1

■ B8ZS line code format ■ HDB3 line code for E1

TURNUP STEPS

Unpack the Total Access 1000 T1/E1 LIU card and inspect for damage. If damage is

apparent, refer to your carrier or supplier for remedy.

Insert the T1/E1 LIU card into the Total Access 1000 slot marked LIU. To insert, hold

the LIU card by the front panel while supporting the bottom edge of the card. Align

the card edge with the guide groove in the Total Access 1000 chasis. Insert into

chassis until the edge card connector seats firmly into the chassis backplane. Lock

the unit in place by pushing in on the locking levers.

There are two LED indicators on the LIU front panel, one for each T1/E1 network

loop. They function as follows:

T1/E1 LIU LEDS

LOOP 1 - 2 ● RED Alarm present on loop

● YELLOW Loop in a test mode

● GREEN No alarm conditions

Connect VT100 compatible terminal to BCU front panel ADMIN port.

4a. Connect straight through DB-9 cable

4b. Run terminal emulation program

4c. If using Windows HyperTerminal, open by selecting

Programs/Accessories/Hyperterminal

NOTE: To ensure proper display background, select VT100 Terminal Emulation under

settings.

Proceed through menus to the T1/E1 LIU

5a. LOGIN (default login: ADMIN, PASSWORD)

5b. select Line Interface Unit (2)

5c. select Provisioning (2)

5d. select Loop to Provision (N/P)

5e. select Provisioning item (1-3)

NOTE: To traverse through the menus, select the desired entry and press Enter. To work

backward in the menu, press ESC (escape key).

Testing – to access the test menu for an access module, select test

(item 4 after 5b).

TESTING

■ Remote Line Loopback – T1/E1 data is looped back to the remote network with

framing and line coding unchanged.

■ Remote Payload Loopback – T1/E1 data is looped back toward remote network

with framing and line code regenerated by the LIU.

■ Local Network Loopback – Customer data is looped back from the LIU.

COMPLIANCE

This product is intended to be installed in a Total Access 1000 chassis providing a

Type “B” or “E” enclosure, with Restricted Access.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Changes or modifications not expressly approved by ADTRAN could void the user’s

authority to operate this equipment.

WARRANTY

ADTRAN will replace or repair this product within the warranty period if it does not

meet its published specifications or fails while in service. Warranty information can

be found at www.adtran.com/warranty. USA and Canadian customer Faxback:

(877) 457-5007, Document 414.

■ For a complete Installation and Maintenance Practice (P/N 61179010L1-5): (877) 457-5007, Faxback Document 893. Please have your fax number ready. ■

C A U T I O N

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

Code Input Output

Power Code (PC) C C

Telecommunication Code (TC) X –

Installation code (IC) A –

PRICING AND AVAILABILITY 800.827.0807

TECHNICAL SUPPORT 800.726.8663

RETURN FOR REPAIR 256.963.8722

www.adtran.com

0212 61179010L1-22A

ADTRAN Total Access 1000 DSLAM ATM Dual T1 Job Aid

ADTRAN Total Access 1000 DSLAM ATM Dual T1 Job Aid

ADTRAN Total Access 1000 DSLAM ATM Dual T1 Job Aid

Related papers

Other documents