Moxa MD-119 Series User manual

Brand: Moxa

Model: MD-119 Series

Type: User manual

MD-119 Hardware User’s Manual

Edition 2.0, February 2017

www.moxa.com/product

MD-119 Hardware User’s Manual

The software described in this manual is furnished under a license agreement and may be used only in accordance with

the terms of that agreement.

Trademarks

The MOXA logo is a registered trademark of Moxa Inc.

All other trademarks or registered marks in this manual belong to their respective manufacturers.

Disclaimer

Information in this document is subject to change without notice and does not represent a commitment on the part of

Moxa.

Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited

to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the

products and/or the programs described in this manual, at any time.

Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for

its use, or for any infringements on the rights of third parties that may result from its use.

This product might include unintentional technical or typographical errors. Changes are periodically made to the

information herein to correct such errors, and these changes are incorporated into new editions of the publication.

Technical Support Contact Information

www.moxa.com/support

Moxa

Americas

Toll

-free: 1-888-669-2872

Tel:

+1-714-528-6777

Fax:

+1-714-528-6778

Moxa China (Shanghai office)

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa A

sia-Pacific

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045

Table of Contents

1. Introduction ...................................................................................................................................... 1-1

Overview ........................................................................................................................................... 1-2

Package Checklist ............................................................................................................................... 1-2

Product Features ................................................................................................................................ 1-2

MD-119 Hardware Specifications .......................................................................................................... 1-3

2. Hardware Introduction ..................................................................................................................... 2-1

Appearance and Layout ....................................................................................................................... 2-2

Dimensions ........................................................................................................................................ 2-3

LED Indicators .................................................................................................................................... 2-3

On-screen Display Control Buttons ........................................................................................................ 2-3

3. Hardware Installation and Peripherals .............................................................................................. 3-1

Installing the MD-119 .......................................................................................................................... 3-2

Wiring Requirements ........................................................................................................................... 3-2

Connecting Power Sources ................................................................................................................... 3-3

Grounding the MD-119 ........................................................................................................................ 3-3

Connecting Data Transmission Cables ................................................................................................... 3-3

Connecting to a Serial Device ....................................................................................................... 3-3

Connecting to Computers or Laptops ..................................................................................................... 3-4

Enabling the Built-in Buzzer ................................................................................................................. 3-5

A. Regulatory Approval Statement ........................................................................................................ A-1

B. On-screen Display and Display Configuration .................................................................................... B-1

On-screen Display (OSD) Controls ........................................................................................................ B-2

Opening the Configuration Screen ................................................................................................. B-2

OSD Passwords/Keycode ..................................................................................................................... B-2

OSD Filetree Legend ........................................................................................................................... B-3

OSD Menu Map ................................................................................................................................... B-3

Main Group 1 .............................................................................................................................. B-4

Main Group 2 .............................................................................................................................. B-5

Main Group 3 .............................................................................................................................. B-6

OSD Menu Items Explained .................................................................................................................. B-7

Basic Image Properties ................................................................................................................ B-7

Picture: PIP Adjustments .............................................................................................................. B-8

Picture: Advanced Settings ......................................................................................................... B-10

Swap Input Sources: Main to Second / Second to Main .................................................................. B-12

Image Information .................................................................................................................... B-12

Auto-Setup ............................................................................................................................... B-13

Display Setup: OSD ................................................................................................................... B-13

Display Setup: User Settings ...................................................................................................... B-15

Display Setup: Preset Defaults .................................................................................................... B-16

Display Setup: Service Menu ...................................................................................................... B-17

Display: Input Sources / Dual Image Displays ............................................................................... B-18

Power Off ................................................................................................................................. B-20

C. Display UART Command .................................................................................................................... C-1

Connecting to the Display .................................................................................................................... C-2

UART Software Configuration ............................................................................................................... C-2

Date Rate ................................................................................................................................... C-2

Data Format ............................................................................................................................... C-2

UART Command Format ...................................................................................................................... C-2

Command Format Description ....................................................................................................... C-2

Downloading Files ............................................................................................................................... C-4

Downloading Files ....................................................................................................................... C-4

Downloading Dual RGB File ........................................................................................................... C-4

Uploading/Downloading Configuration Files ..................................................................................... C-4

OSD Control Command ....................................................................................................................... C-5

BLI (Brightness Control) ............................................................................................................... C-5

DST (Display State) ..................................................................................................................... C-5

MAN (Manufacturer ID Code) ........................................................................................................ C-6

POT (Potentiometer Control) ......................................................................................................... C-6

SNB (Serial Number Query) .......................................................................................................... C-6

TYP (Type/Model/Number Query) .................................................................................................. C-7

SWI (Software Version Query) ...................................................................................................... C-7

VER (Version Number) ................................................................................................................. C-7

MCC (OSD Control) ...................................................................................................................... C-8

MCC Control Command ....................................................................................................................... C-9

1. Introduction

The MD-119 series displays are designed to meet exacting performance and durability standards. The19-inch

panels featuring a 4:3 aspect ratio, 1280 x 1024 pixel resolution, full range dimming, and optional optical

bonding make these displays ideal for a variety of applications. These computer display terminals further meet

required industrial standards and are perfectly suited for a wide variety of industrial uses that require rugged,

reliable performance, whether indoors or out.

Further, these displays use either AC or DC power inputs, simplifying the installation of the displays at field

sites, and also offer PIP (Picture-In-Picture) and PBP (Picture-By-Picture) modes, allowing for multiple image

display configurations on a single screen.

The following topics are covered in this chapter:



Overview



Package Checklist



Product Features



MD-119 Hardware Specifications

MD-119 Hardware Introduction

1-2

Overview

The MD-119 series has been designed to fit the peculiar environmental demands of industrial systems. The

19-inch panel features a 4:3 aspect ratio and a 1280 x 1024 pixel resolution, making this display ideal for any

industrial application requiring detailed, high-resolution imagery. In addition, with full range dimming, optical

bonding (optional), these computer display terminals satisfy a variety of international standards.

Package Checklist

The MD-119 series includes the following models:

MD-119: 19-inch industrial display with 4:3 aspect ratio, LED backlighting, multiple input AC/DC power supply,

and tape bonding; optical bonding and capacitance touch screens are available as optional requests

Each model ships with the following items:

• MD-119 display

• DVI to VGA adapter

• VGA Cable

• DVI-D Cable

• Console Mounting Kits

• DC terminal block (for powering device)

• DC terminal block (for powering the buzzer)

• Documentation and driver DVD

• Quick installation guide (printed)

• Warranty card

NOTE

Please notify your sales representative if any

of the above items are missing or damaged.

Product Features

The MD-119 display has the following features:

• 19-inch wide viewable image size with 4:3 aspect ratio and 1280 x 1024 pixel resolution

• LED backlighting

• Optical bonding (optional)

• Surface capacitance touch panel (optional)

• Picture-in-picture / picture-by-picture (PIP/PBP)

• Multi-power input (24 VDC, 110 to 230 VAC)

• IP54 rated front panel

MD-119 Hardware Introduction

1-3

MD-119 Hardware Specifications

Display

Panel Size:

19’’ wide viewable image size

Panel Type:

Aspect Ratio:

4:3

Pixels:

1280 x 1024 (SXGA)

Pixel Pitch (RGB):

0.282 (H) x 0.282 (V) mm

Response Time:

5 ms (typical)

Contrast Ratio:

1000:1(typical)

Light Intensity:

350 cd/m

Viewing Angles:

85° x 80° (Right-Left x Up-Down)

Active Display Area:

376.32 (H) x 301.06 (V) mm/14.81(H) x 11.85 (V) (inch)

Max Colors:

16.7M (8 bits/color)

Display Interface:

VGA output x 1, DVI-I input x 2, BNC composite x 3

Serial Interface

Console Port

: 2 RS-232/422/485 ports, (1 is manufacture reserved), (DB9 male)

Serial Communication Parameters

Data Bits:

5, 6, 7, 8

Stop Bits:

1, 1.5, 2

Parity:

None, Even, Odd, Space, Mark

Baudrate:

9600 bps

Serial Signals

-232: TxD, RxD, DTR, DSR, RTS, CTS, DCD, GND

-422: TxD+, TxD-, RxD+, RxD-, GND

-485-4w: TxD+, TxD-, RxD+, RxD-, GND

-485-2w: Data+, Data-, GND

Front Panel

OSD:

5 x OSD control

Physical Characteristics

Housing:

Aluminum sheet metal

Weight:

9.69 kg

Dimensions:

82 x 483 x 444 mm (3.29 x 19.02 x 17.48 in)

Mounting:

Console mounting

Environmental Limits

Operating Temperature:

-15 to 55°C (5 to 131°F)

Storage Temperature:

-20 to 60°C (-4 to 140°F)

Ambient Relative Humidity:

5 to 95% (non-condensing)

Anti

-Vibration:

• IEC 60945

• DNV 2.4, Class A/Class C

Power

Requirements

Input Voltage:

• 24 VDC (

with tolerance from 18 to 36 VDC), 2-pin screw-type terminal block

•

110 to 230 VAC, 50/60 Hz

Power Consumption:

42 W

•

75W (standard)

•

90W (full loading)

Standards and Certifications

Safety:

UL/cUL, CCC (Pending)

EMC:

EN 55032 Class B, EN 55024-4-2, EN 55024-4-3, EN 55024-4-4, FCC Part 15 Subpart B Class A

Marine:

IEC 60945 4

(Pending), DNV (Pending), IACS-E10 (Pending)

IP Rating:

IP54 (IP66 by request)

MD-119 Hardware Introduction

1-4

Compass Safe Distance:

<80cm (to be tested by DNV)

Green Product:

RoHS, cRoHS, WEEE

Warranty

Warranty Period:

One year

Details:

See www.moxa.com/warranty

We recommend taking the following precautions to minimize heat build-up within the display:

• Position the display within ±40° of the vertical

• If:

(a) the display is not positioned within ±40° of the vertical, or

(b) the operating temperature exceeds 25°C, or

then install an external fan to increase airflow upwards through the chassis

Important Safety Precaution:

Even though the display is rated to operate within the IEC 60945 standard of -15 to 55°C for industrial

applications, it is best to ensure that the operating temperature does not exceed 25°C. Doing so will

significantly increase the lifespan of your display and reduce service costs.

2. Hardware Introduction

The MD-119 display is compact, well-designed, and rugged enough for industrial applications. LED indicators

help you monitor performance and identify trouble spots, multiple serial ports allow you to connect different

devices for wireless operation, and the reliable and stable hardware platform lets you devote your attention to

developing your applications.

The following topics are covered in this chapter:



Appearance and Layout



Dimensions



LED Indicators



On-screen Display Control Buttons

MD-119 Hardware Hardware Introduction

2-2

Appearance and Layout

MD-119 Hardware Hardware Introduction

2-3

Dimensions

LED Indicators

LED Name LED Color LED Function

Power Green Power is on and functioning normally

Yellow Display is suspended

On-screen Display Control Buttons

The front panel of the MD-119 comes with a power button and four on-screen display (OSD) control buttons for

accessing and adjusting image properties. Please refer to Appendix B for detailed explanations of individual

items on the OSD menu and adjusting image properties.

3. Hardware Installation and Peripherals

In this chapter, we show how to connect the MD-119 to its central processing unit and to various devices.

The following topics are covered in this chapter:



Installing the MD-119



Wiring Requirements



Connecting Power Sources



Grounding the MD-119



Connecting Data Transmission Cables

 Connecting to a Serial Device



Connecting to Computers or Laptops



Enabling the Built-in Buzzer

MD-119 Hardware Hardware Installation and Peripherals

3-2

Installing the MD-119

Cabinet Mounting

The MD-119 comes with a console mounting kit that helps users mount the display into a cabinet. There are

eleven sets of console mounting holes on four sides of the MD-119. Each mounting point has two

standards-compliant locations for screws to go into, depending on the thickness of the wall or cabinet. Simply

fasten the screws to the mounts in the correct place.

For safety reasons, it is important to ensure that all four corners and sides of the panel are firmly attached to

the cabinet, so that the display and cabinet assembly is stabilized.

ATTENTION

Clean the monitor using a soft

material such as a microfiber cloth. You may also use LCD cleaning liquid to clean

the monitor.

Avoid using coarse or rough material to clean the monitor as thi

s may damage the surface of the display.

Wiring Requirements

This section describes how to connect serial devices to the display.

You should read and follow these common safety precautions before proceeding with the installation of any

electronic device:

• Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must

cross, make sure to cut interference problems by keeping the wires perpendicular at the intersection points

NOTE

To avoid interference

do not, in the same conduit, run signal or communication wiring together with power

wiring. Wires with different signal characteristics should be routed separately.

• Use the type of signal transmitted through a wire to determine which wires should be kept separate. The

rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.

• Keep input wiring and output wiring separate.

• It is advisable to label the wiring to all devices in the system.

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or wiring your

MD-119.

Wiring Caution!

Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes

dictating the maximum current allowable for each wire

size.

If electrical current exceeds the maximum rating the wire will overheat; this will cause serious damage to your

equipment.

Temperature Caution!

Be careful when handling the unit. When the unit is plugged in, the internal components generate a lot of heat,

heating the outer casing.

MD-119 Hardware Hardware Installation and Peripherals

3-3

Connecting Power Sources

The MD-119 offers 24 VDC power input with the terminal block, and also comes with a 110 to 230 VAC power

input. If power is supplied properly, the Power LED will light up. To enable the power failover function, connect

both AC and DC power inputs.

For safety reasons, please use cables with the following specifications:

Wire range: 14-22 AWG, torque 7 lb

Grounding the MD-119

Grounding and proper wiring layout help limit the effects of noise from electromagnetic interference (EMI). The

ground wire must be a minimum 18 AWG, and must be connected (via the grounding screw) prior to connecting

the power. The ground connector is located on the bottom panel of the display, as shown in the Appearance

and Layout diagram on page 2-2.

ATTENTION

This product is intended to be mounted to a well

-grounded mounting surface, such as a metal panel.

Connecting Data Transmission Cables

This section describes how to connect the MD-119 display to various interfaces.

Connecting to a Serial Device

Use a serial cable to plug your serial device into the display’s serial port. Please note that serial port 1 is

reserved for the manufacturer’s configuration process; only serial port 2 is available for connecting serial

perhipherals. Serial port 2 terminates in a male 9-pin D-Sub (DE9) connector, and can be software-configured

as an RS-232, RS-422, or RS-485 interface. The pin assignments are shown in the table on the following page:

DB9 Male Port

-232/422/485 Pinouts

Pin RS-232 RS-422

RS-485

(4-wire)

RS-485

(2-wire)

1 DCD TxDA(-) TxDA(-) –

2 RxD TxDB(+) TxDB(+) –

3 TxD RxDB(+) RxDB(+) DataB(+)

4 DTR RxDA(-) RxDA(-) DataA(-)

5 GND GND GND GND

6 DSR – – –

7 RTS – – –

8 CTS – – –

MD-119 Hardware Hardware Installation and Peripherals

3-4

Connecting to Computers or Laptops

The MD-119 comes with two DVI-I inputs, allowing to connecting two computers or laptops. In addition, a VGA

output is available for extending to an additional display. Pin assignments are shown below:

DB15 Female Connector

Pin No. Signal Definition

1 Red

2 Green

3 Blue

4 NC

5 GND

6 GND

7 GND

8 GND

9 VCC

10 GND

11 NC

12 DDC Data

13 HSYNC

14 VSYNC

15 DDC Clock

DVI-I Connector

Pin No. Signal Definition

1 T.M.D.S. Data2-

2 T.M.D.S. Data2+

3 T.M.D.S. Data2/4 Shield

4 N/C

5 N/C

6 DDC Clock

7 DDC Data

8 Analog Vertical Sync

9 T.M.D.S. Data1-

10 T.M.D.S. Data1+

11 T.M.D.S. Data1/3 Shield

12 N/C

13 N/C

14 +5V Power

15 Ground

(return for +5V, HSync, and VSync)

Pin No. Signal Definition

16 Hot Plug Detect

17 T.M.D.S. Data0-

18 T.M.D.S. Data0+

19 T.M.D.S. Data0/5 Shield

20 N/C

21 N/C

22 T.M.D.S. Clock Shield

23 T.M.D.S. Clock+

24 T.M.D.S. Clock-

C1 Analog Red

C2 Analog Green

C3 Analog Blue

C4 Analog Horizontal Sync

C5 Analog Ground

(analog R, G, B return)

MD-119 Hardware Hardware Installation and Peripherals

3-5

Enabling the Built-in Buzzer

The MD-119 comes with a built in a buzzer terminal block and is located on its bottom panel. Insert the leads

from a 5 to 12 V power source into the terminal block to enable the buzzer for use.

A. Regulatory Approval Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that

may cause undesired

operation.

Class A

：

FCC Warning! This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his/her own expense.

European Community

Warning:

This is a class A product. In a domestic environment this product may cause radio interference in which case

the user may be required to take adequate measures.

B. On-screen Display and Display

Configuration

This chapter discusses how to navigate the On-screen Display (OSD) and how to use the menus to adjust the

panel’s image properties.

The following topics are covered in this appendix:



On-screen Display (OSD) Controls

 Opening the Configuration Screen



OSD Passwords/Keycode



OSD Filetree Legend



OSD Menu Map

 Main Group 1

 Main Group 2

 Main Group 3



OSD Menu Items Explained

 Basic Image Properties

 Picture: PIP Adjustments

 Picture: Advanced Settings

 Swap Input Sources: Main to Second / Second to Main

 Image Information

 Auto-Setup

 Display Setup: OSD

 Display Setup: User Settings

 Display Setup: Preset Defaults

 Display Setup: Service Menu

 Display: Input Sources / Dual Image Displays

 Power Off

MD-119 Hardware On-screen Display and Display Configuration

B-2

On-screen Display (OSD) Controls

Opening the Configuration Screen

To configure the panel display settings, open the on-screen display (OSD) configuration panel by pressing the

Menu button. The LCD panel will then display a configuration menu superimposed over the currently displayed

image. The OSD controls consist of two LEDS (to indicate system status), a MENU button for opening and

closing the OSD, and four arrow buttons for navigating the OSD menus.

LED Indicators

The following table describes the LED indicators located on the front of the MD-119.

LED Name LED Color LED Function

(unmarked) Green Power is on and functioning normally

Red Display is suspended

Buttons

Right Arrow Key: Allows users to navigate to sub-menus from a specific menu item

Left Arrow Key: Allows users to exit a sub-menu and return to the previous menu

Up Arrow Key: Allows users to navigate the items of a single OSD menu, or increase the brightness of the

display

Down Arrow Key: Allows users to navigate the items of a single OSD menu, or decrease the brightness of the

display

OSD Passwords/Keycode

When pressing Menu button, you may be asked for a password, please use 321.

When entering the Full Menu mode, you may be asked for a password, please use 158.

MD-119 Hardware On-screen Display and Display Configuration

B-3

OSD Filetree Legend

The OSD menu includes parameters that are specific for RGB mode, DVI mode and which are accessible

depending on whether you are using the Full or “Simplified” menu structure. Not all functions shown in the

menu structure are available in every mode. To more easily identify which parameters are available in a given

mode, the illustrations in this section are marked with a color legend. These colors are not visible in the actual

OSD environment.

OSD Menu Map

The MD-119 OSD control is divided into 3 groups. See the following figures for details.

MD-119 Hardware On-screen Display and Display Configuration

B-4

Main Group 1

In this group (and its sub groups) the user can adjust image properties that directly affect the picture across

all incoming signal sources. Some of these subgroups have further options; please review this menu map to

quickly determine where a desired property is located within the menu hierarchy. For detailed information

about each item and its parameters, please review the OSD Menu Items Explained later in this section.

Page is loading ...

Moxa MD-119 Series User manual

Moxa MD-119 Series User manual

Moxa MD-119 Series User manual

Related papers

Other documents