Midmark Procenter Systems Installation guide

Procenter Systems
Midmark
Brand
Midmark
Model
Procenter Systems
Type
Installation guide

Midmark Procenter Systems offer a versatile and efficient solution for dental professionals, providing a range of capabilities to enhance patient care and streamline workflows. With its user-friendly interface and comprehensive features, the system empowers dentists to perform a variety of tasks, including controlling dental instruments, adjusting chair positions, and managing patient information. Additionally, the system's integration with imaging software enables seamless access to patient X-rays and other diagnostic images, enhancing treatment planning and communication with patients.

Midmark Procenter Systems offer a versatile and efficient solution for dental professionals, providing a range of capabilities to enhance patient care and streamline workflows. With its user-friendly interface and comprehensive features, the system empowers dentists to perform a variety of tasks, including controlling dental instruments, adjusting chair positions, and managing patient information. Additionally, the system's integration with imaging software enables seamless access to patient X-rays and other diagnostic images, enhancing treatment planning and communication with patients.

1
© 2010 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
DA2444i
003-2032-00 Rev. B (3/28/12)
Procenter Assistant’s Unit, Console Mounted on an
Elevance Chair Installation Guide
DA2440i
Console
Faceplate
Outside cover lip ts under
console top, then push in
until ball studs snap into t-
tings in frame.
Inside cover lip ts under con-
sole frame and is secured with
screw on bottom.
Step 2: Remove console faceplate (two screws
with washers) for easier access to
mounting holes.
Step 3: Holding the mounting arm straight out from the front of
the console, install the stop pin in the desired Left or
Right side mounting hole.
Note: The stop pin is factory set for a LEFT side mounting on a Console mounted
on (patient’s) left side of the chair. Only move the stop pin if you are
installing a RIGHT hand unit.
Stop Pin
Left Hand
mounting hole
Right Hand
mounting hole
Left (chair) side
Right
side
Language of origin: English
WARNING
Always disconnect power before removing covers. Failure to do
so may result in personal injury.
Step 1: Remove the inside and outside console covers.
NextNext
BackBack
midmark.com
Style G
2
© 2010 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
Installing the Mount Arm Assembly
DA2442i
Step 1: Route the umbilical and vacuum line
into the Console.
Note: Take care not to kink the umbilical or vacuum lines.
Leveling Set
Screws (3)
Mounting Screws (3)
Step 2: Rotate Arm Adapter clockwise and
install Mount Arm Assembly using 3
mounting screws, loosely tightened.
Step 3: Install 3 leveling set screws and level
the mount arm assembly. Tighten the 3
mounting screws when arm is level.
Arm Adapter
Step 4: Plug the Assistant’s Unit Power into the
Interface PC Board, J6 or J10 socket.
Plug the Assistant’s Unit keypad control
into the J1 or J2 socket.
DA2439i
Interface PC Board
J1 J2
J9
BLK
WHT
Red wire not used
Assistant’s Unit Power
Keypad Control
NextNext
BackBack
midmark.com
Style G
Color Page
3
© 2010 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
DA138100i
Step 1: Cut 1/8" yellow tubing.
Insert T-Fitting.
Connect to 1/8" yellow tubing from Assistant’s Unit.
Connecting Tubing
Step 2: Connect Assistant’s Unit vacuum tubing to
3/4" ribbed gray vacuum line from umbilical.
In J-Box (not shown): Connect 3/4" ribbed
gray vacuum line from umbilical to facility’s
central vacuum line.
Step 3: Remove plugged section of blue tubing.
Connect to 1/8” blue tubing from Assistant’s Unit.
NextNext
BackBack
midmark.com
Style G
Color Page
4
© 2010 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
Installation Checklist
Test Description of good installation criteria
1 Mount Arm and Assistant’s Unit are level.
2
Mount Arm and Assistant’s Unit rotate and
move easily.
3
Air and Water tools work on the Assistant’s
Unit - no wires or tubing are pinched by cov-
ers or mountings.
4
Wipe Console and Assistant’s Unit with a
soft dry cloth to remove any dirt or smudges.
Install Covers on Console...
Put Console faceplate on Console (2 screws).
Put inner cover on Console to cover all electrical
connections.
Put outer cover on Console.
Note: Be careful not to pinch or kink tubing or wires when
installing covers.
Assemble and install covers on Console
DA2440i
Console
Faceplate
Outside cover lip ts under
console top, then push in
until ball studs snap into
ttings in frame.
Inside cover lip ts under
console frame and is secured
with screw on bottom.
NextNext
BackBack
midmark.com
Style G
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Midmark Procenter Systems Installation guide

Procenter Systems
Midmark
Brand
Midmark
Model
Procenter Systems
Type
Installation guide

Midmark Procenter Systems offer a versatile and efficient solution for dental professionals, providing a range of capabilities to enhance patient care and streamline workflows. With its user-friendly interface and comprehensive features, the system empowers dentists to perform a variety of tasks, including controlling dental instruments, adjusting chair positions, and managing patient information. Additionally, the system's integration with imaging software enables seamless access to patient X-rays and other diagnostic images, enhancing treatment planning and communication with patients.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents