Extron TLP 700TV User manual

TLP 700MV and TLP 700TV

User Guide

TouchLink

TouchLink Touchpanel Control Systems

68-1378-01 Rev. D

01 20

Safety Instructions

Safety Instructions • English

WARNING: This symbol, ,when used on the product, is

intended to alert the user of the presence of uninsulated dangerous

voltage within the product’s enclosure that may present a risk of electric

shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)

instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron

website, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses

Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und

die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in

den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y

mantenimiento recogidas en la documentación proporcionada con el

equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad

de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du

produit d’une tension électrique dangereuse susceptible de provoquer

un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance

importantes qui se trouvent dans la documentation fournie avec le

matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la

réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets

connexes, lisez les informations de sécurité et de conformité Extron, réf.

68-290-01, sur le site Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa

all’interno del contenitore del prodotto che può costituire un rischio di

scosse elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di importanti istruzioni di funzionamento

e manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,

compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento

alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo

68-290-01, sul sito web di Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego

napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie

porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji

(obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji

wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,

zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część

numer 68-290-01, na stronie internetowej Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению

электрическим током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций

по эксплуатации и обслуживанию в руководстве,

прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других

вопросах см. руководство по безопасности и соблюдению

нормативных требований Extron на сайте Extron: ,

www.extron.com, номер по каталогу - 68-290-01.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍

使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01。

All trademarks mentioned are the property of their respective owners..

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

), registered service marks (

), and trademarks (

) are the property of RGBSystems, Inc. or

ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

)

Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, Glitch Free, Global Configurator,

Global Scripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,

PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

System INTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTP Systems, and

ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D

Ripple Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator,

DSPConfigurator, DSVP (Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk,

MAAP, MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, SIS,

Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을

경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에

대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및

규제 준수 안내서, 68-290-01 조항을 참조하십시오.

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資

訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規

遵守手冊》，準則編號 68-290-01。

安全上のご注意 • 日本語

警告: この記号が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守(整備)の指示についてユーザーの注意

を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に

ついては、エクストロンのウェブサイト www.extron.com より『 Extron Safety

and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。

Conventions Used in this Guide

Notiﬁcations

In this user guide, the following are used:

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

X1&

X2)

X2#

X2!

}

NOTE: For commands and examples of computer or device responses mentioned

in this guide, the character “0” is used for the number zero and “O” represents the

capital letter “o”.

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at www.extron.com/technology/glossary.aspx.

Contents

Introduction............................................................ 1

About the TLP 700MV and TLP 700TV ............... 1

Features ............................................................. 2

Requirements ..................................................... 3

Software ......................................................... 3

Hardware ........................................................ 3

Panel Features ...................................................... 4

TLP 700MV Front Panel

Features and Operations ................................... 4

TLP 700MV Rear Panel

Features and Connections ................................. 5

TLP 700TV Front Panel

Features and Operations ................................... 8

TLP 700TV Rear Panel

Features and Connections ................................. 9

With Stand Attached ...................................... 9

TLP 700TV Base Features ................................ 10

On-screen Menus ............................................... 12

How to Access the Internal

On-screen Menus ............................................ 12

Main Screen ..................................................... 12

Volume Screen ................................................. 13

Time Screen ..................................................... 14

Network Screen ................................................ 14

Video Screen .................................................... 15

Touch Calibration Screen .................................. 15

Conﬁguration Software ..................................... 16

Software Overview ............................................ 16

Installing the Software ....................................... 17

Installation from the Extron Web Site ............. 17

Updating the Firmware ..................................... 18

Updating Firmware Using the Extron

Firmware Loader Utility ................................ 18

Updating Firmware From a

Web Browser GUI ........................................ 19

Using the TouchLink Panel Web Pages ............. 20

Using GUI Conﬁgurator ..................................... 22

Using Global Conﬁgurator ................................. 27

Mounting ............................................................... 33

Rack Mounting the TLP 700MV ........................ 33

Underwriters Laboratories Guidelines for

Rack Mounting ............................................ 33

Rack Mounting the TLP 700MV .................... 33

Wall Mounting the TLP 700MV ......................... 34

Wall Mounting the TLP 700MV

with a Wall Box ................................................ 35

Desktop Mounting the TLP700TV .................... 36

Removing the TLP 700TV Base for

VESA Mounting ............................................... 36

VESA Mounting the TLP 700TV ........................ 41

Reset Modes ........................................................ 42

Button Labels ...................................................... 43

Button Label Software ...................................... 43

Installing or Replacing Button Labels ............ 43

Button Label Generator Software .................. 43

Installing the Button-Label Generator

Software ...................................................... 43

Using the Button-Label Generator

Software ...................................................... 44

Replacing Button Labels ................................... 45

TLP 700MV and TLP 700TV • Contents v

TLP 700MV and TLP 700TV • Contents vi

Introduction

This guide describes the function, installation and operation of the TouchLink TLP700MV

and TLP 700TV Touchpanels. Unless otherwise stated, the terms “TLP 700 series,”

“TLP700,” “touchpanel,” and “TouchLink touchpanel” refer to both models. The guide also

provides information about optional accessories that are available from Extron for both

panels.

This section provides the following information:

• About the TLP 700MV and TLP 700TV

• Features

• Requirements

About the TLP 700MV and TLP 700TV

Both models have 7-inch LCD screens with a resolution 800x480. The screen displays

graphic objects and text, which are associated with user-defined functions. The touch

overlay allows the user to initiate or activate functions by touching the objects on the screen.

The Extron TLP 700MV is a wall mounted TouchLink panel. The TLP 700TV comes with

a stand that allows it to be placed on a desktop. If the stand is removed, the unit can be

VESA

mounted on a wall or furniture, using the optional Extron kits.

Both units have ten push buttons (five along each side of the screen) and an encoder knob.

These allow common, user-defined functions to be activated and calibrated independently

of the screen. The units can be customized by using a bezel kit to cover the buttons, the

encoder knob, or both.

A motion sensor, light sensor, and a speaker provide auto dimming, sleep mode, and

audible feedback.

Extron GUI Configurator software allows the user to design the screen layout by selecting

from existing templates or designing entirely new interfaces on their PC and uploading

the completed project to the TouchLink panel. The user can define the graphics and the

functions associated with those graphics, providing versatility and adaptability to the

configuration and control of an AV system.

TLP 700MV and TLP 700TV • Introduction 1

100-240V 50-60Hz

VID

B-Y

R-Y

RGB

DVI

3 4 5

AUDIO INPUT

RS-232

OUTPUT

RGB

Y, B-Y, R-Y

RGB

LISTED

1T23

I.T.E.

U S

INPUT

LAN

POWER

12V

500mA

MAX

COM 3

G S G

TXRX

RELAY

COM1

RT SC TS

COM 2

G S G

TXRX

RELAY

Extron

OFF

DISPLAY

MUTE

SCREEN

DOWN

VCR

DVD

DOC

CAM

LAPTOP

XPA 1002

1 2

LIMITER/PROTEC

SIGNAL

OVER

TEMP

Extron

XPA 1002

Power Amplier

Extron

SI 28

Surface-mount

Speakers

Extron

TLP 700MV

7" TouchLink

Panel

Extron

IPL 250

IP Link-Ethernet

Control Interface

TCP/IP

Network

Lighting

System

Projector

Screen

Control

Laptop

DVD

Player

Ext

ron

1508

Scalin

g Presentation

Swit

cher

DVI Output

Motion

Detector

RS-232

Contact

Closure

IR Control

to DVD

IR Control

from IPL 250

Relay

Extron

IR Emitter

RS-232

Figure 1. TLP 700MV Application Diagram

Features

7-inch LCD screen — Displays a range of graphic objects and text on an 800 x 480 pixel

screen.

Touch screen overlay — Provides simple and intuitive control over a range of functions by

touching the icons displayed on the screen.

Video preview — Allows composite or S-video previews.

GUI Configurator and Global Configurator Software — Allows the user to design a

custom graphical user interface and associate a range of different functions with objects in

that display. No programming knowledge is needed.

Easy configuration and flexibility — On-screen graphics and text, as well as the

functions associated with them, can be easily changed to adapt the control panel to the

evolving needs of the system, avoiding the need for additional control modules.

Ten buttons — For common, user-defined functions.

Ethernet connection — Provides an inexpensive, easily installed, cabling option for

connecting products located anywhere else on the network.

Compatible with most Extron IP Link products — Allows easy integration into existing

systems.

NOTE: These products are not compatible with the Extron Pro series of devices.

Front panel encoder knob — Primarily for volume control, but can be configured for other

functions.

Light sensor — Adjusts LCD screen backlighting to compensate for ambient lighting.

Motion sensor — When no motion is detected for a user-defined period of time, the unit

enters sleep mode to conserve power. When a user approaches the screen, the panel

detects motion and is reactivated.

TLP 700MV and TLP 700TV • Introduction 2

Loudspeaker — Provides audible feedback in response to events triggered by the user.

Multiple mounting options — The TLP 700MV can be wall-mounted, rack-mounted, or

furniture-mounted.

The TLP 700TV comes with a stand that allows it to be placed on a desktop. If the stand is

removed, the unit can be VESA-mounted on a wall or furniture using either of the optional

Extron kits.

Color Options for TLP 700MV — The TLP 700MV is available in different color versions.

Customization kits — A range of kits are available to customize the TouchLink panel.

Requirements

Software

For a complete list of the requirements for running GlobalConfigurator 3 or

GUIConfigurator, see www.extron.com for that software.

NOTE: These touchpanels and controllers are not compatible with GUI Designer or

Global Configurator Plus and Global Configurator Professional.

Hardware

An Extron IP Link control interface must also be connected to the same network domain as

the TouchLink panel. See www.extron.com for a list of suitable controllers.

NOTE: These touchpanels and controllers are not compatible with the Extron Pro

series of devices.

TLP 700MV and TLP 700TV • Introduction 3

Panel Features

This section describes:

TLP 700MV Front Panel Features and Operations

TLP 700MV Rear Panel Features and Connections

TLP 700TV Front Panel Features and Operations

TLP 700TV Rear Panel Features and Connections

TLP 700TV Base Features

TLP 700MV Front Panel Features and Operations

Figure 2. TLP 700MV Front Panel

Buttons — These ten backlit push-buttons (ﬁve on either side of the screen) can be

conﬁgured to execute user-deﬁned functions using the Extron Global Conﬁgurator (see

Using Global Configurator on page 27 and Using the Button-Label Generator

Software on page 44).

Motion Sensor — Is capped with a small Fresnel lens that focuses light onto the

sensor. When no motion has been detected for a user-deﬁned period of time, the unit

goes into sleep mode. When motion is detected in the vicinity of the panel, the screen

display is restored and all buttons are active.

Encoder Knob — Controls the volume or it can be conﬁgured for other functions.

Light Sensor — Monitors the level of ambient light and adjusts the screen brightness

and button backlighting.

LCD screen — Has an 800x480 resolution with a touch overlay. A graphic user

interface is designed using the Extron GUI Configurator software to display buttons,

text, or icons on the screen (page 22). These can be conﬁgured for a range of user-

deﬁned functions, using the Extron Global Configurator software (page 26).

Speaker — A single 2 watt speaker provides audible feedback for the user.

TLP 700MV and TLP 700TV • Panel Features 4

There are three buttons and an LED recessed behind the bezel. These buttons are used to

configure the unit and reset parameters to factory defaults:

Figure 3. TLP 700MV Front Panel with Bezel removed

Reset button — Allows the unit to be reset in any of four different modes (see Reset

Modes on page41).

Menu button — Activates the on-screen menus for setting up and calibrating the unit

(see page12).

Reset LED — Visible only when the bezel has been removed. It lights as an indicator

for the Reset modes (see Reset Modes on page41).

TLP 700MV Rear Panel Features and Connections

Figure 4. TLP 700MV Rear Panel Features

Power Connector

Video Input

Network Connector

TLP 700MV and TLP 700TV • Panel Features 5

Power Connector (see figure 4 on the previous page) — Connect the two pole, 3.5

mm captive screw connector from the provided power supply to the power supply

socket on the rear panel. Ensure the connections have the correct polarity as shown

below:

12V

0.4A MAX

POWER

3/16"

(5 mm) Max.

DC Power

Input

POWER

12V

0.4A MA

Power Supply

Output Cord

SECTION A–A

Ridges

Smooth

DC Power Cord

Captive Screw Connector

Ground

+12 VDC input

External Power Supply

(12 VDC, 1.0 A max.)

Ground all

Devices

Figure 5. Power Supply Connection

WARNING: The two power cord wires must be kept separate while the power

supply is plugged in. Remove power before wiring.

AVERTISSEMENT : Les deux cordons d’alimentation doivent être tenus à l’écart

l’un de l’autre quand l’alimentation est branchée. Couper l’alimentation avant

de faire l’installation électrique.

CAUTION: Risk of Explosion. Do not replace the battery with an incorrect type.

Dispose of used batteries according to the instructions of the manufacturer.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de

pile. Débarrassez-vous des piles utilisées selon les instructions du fabricant.

Caution

TLP 700MV and TLP 700TV • Panel Features 6

ATTENTION:

• Always use a power supply supplied by or speciﬁed by Extron. This product is

intended for use with a UL Listed power source marked “Class 2” or “LPS” and

rated 12VDC, minimum 1.0 A. Use of an unauthorized power supply voids all

regulatory compliance certiﬁcation and may cause damage to the supply and the

end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. Ce

produit est destiné à une utilisation avec une source d’alimentation listéeUL avec

l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A minimum. L’utilisation

d’une source d’alimentation non autorisée annule toute conformité réglementaire et

peut endommager la source d’alimentation ainsi que le produit ﬁnal.

• Extron power supplies are certiﬁed to UL/CSA 60950-1 and are classiﬁed as LPS

(Limited Power Source). Use of a non-LPS or unlisted power supply will void all

regulatory compliance certiﬁcation.

• Les sources d’alimentation Extron sont qualiﬁées UL/CSA60950-1 et sont

classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation non-

listée ou non-listéeLPS annulera toute certiﬁcation de conformité réglementaire.

• The power supply shall not be permanently ﬁxed to the building structure or similar

structures.

• La source d’alimentation ne devra pas être ﬁxée de façon permanente à une

structure de bâtiment ou à une structure similaire.

• This power supply is not suitable for use in air handling spaces or in wall cavities.

The power supply is to be located within the vicinity of the Extron AV equipment

in an ordinary location with IEC1010 pollution degree2, and secured to an

equipment rack within a dedicated closet, podium, or desk.

• Cette source d’alimentation n’est pas appropriées pour une utilisation dans les

espaces d’aération ou dans les cavités murales. Cette source d’alimentation doit

être située à proximité de l’équipement audiovisuel d’Extron, dans un endroit

ordinaire avec une pollution IEC1010 degré2, et ﬁxé à un équipement de rack au

sein d’un placard, d’une estrade ou d’un bureau qui lui est dédié.

• The installation shall be in accordance with the applicable provisions of National

Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code

part1, section 16.

• Cette installation doit toujours être en accord avec les mesures qui s’applique

au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical

Code, partie1, section16.

• The length of the exposed wires in the stripping process is critical. The ideal length

is 3/16 inches (5 mm). If they are longer, the exposed wires may touch, causing a

short circuit between them. If they are shorter, the wires can be easily pulled out

even if tightly fastened by the captive screws.

• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les

dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus

longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils

sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis

captives.

• Do not tin the wire leads before installing into the connector. Tinned wires are not

as secure in the connector and could be pulled out.

• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles

étamés ne sont pas aussi bien ﬁxés dans le connecteur et pourraient être retirés.

TLP 700MV and TLP 700TV • Panel Features 7

Video Input (see figure 4 on page 5) — Connect an S-video

or composite video source to the unit, using these two BNC

connectors:

For S-video, connect the Y (luminance) signal to the VID/Y input

and the C (chrominance) signal to the Cinput.

For composite video, connect the input to the VID/Y input.

Network Connector (see figure 4) — The TLP 700MV connects to

an Ethernet LAN using a twisted pair cable, terminated with an RJ-

45 connector (see the ﬁgure at right). Use a straight-through Ethernet

cable to connect the panel to a switch or router. Use a crossover

cable to connect the panel directly to a computer.

Plug one end of the cable into the RJ-45 socket and the other end

into a network switch, hub, or router that is connected to an Ethernet

LAN or the Internet. An Extron IP Link control interface must also be

connected to the same network domain.

The LAN Port connector (see the figure to the right) has two

LED lights. The Link LED lights green to indicate a good network

connection. The Activity LED blinks yellow when network activity

occurs.

TLP 700TV Front Panel Features and Operations

Figure 6. TLP 700TV Front Panel Features

Buttons

Speaker

Motion sensor

Reset button

Encoder knob

Menu button

Light sensor

Reset LED

LCD screen

LAN

RJ-45

Port

Link

LED

Activity

LED

LAN Port

TLP 700MV and TLP 700TV • Panel Features 8

Buttons (see figure 6 on the previous page) — These ten backlit push-buttons (ﬁve

on either side of the screen) can be conﬁgured to execute user-deﬁned functions using

the Extron Global Configurator software (page 26). For information about creating

button labels, see page 43.

Motion Sensor (see figure 6) — Capped with a small Fresnel lens that focuses light

onto the sensor. When no motion has been detected for a user-deﬁned period of time,

the unit goes into sleep mode. When motion is detected in the vicinity of the panel, the

sleep mode is overridden and the screen display is restored.

Encoder Knob (see figure 6) — Controls the volume but it can be conﬁgured for other

functions.

Light Sensor (see figure 6) — Monitors the level of ambient light and adjusts the

screen brightness and button backlighting.

LCD screen (see figure 6) — Has an 800x480 resolution with a touch overlay. A

graphic user interface is designed using the Extron GUI Configurator software (page

22) to display buttons, text, or icons on the screen. These can be conﬁgured for a range

of user-deﬁned functions, using the Extron Global Configurator software (page 26).

Speaker (see figure 6) — A single 2 watt speaker provides audible feedback for the

user.

Reset button (see figure 6) — Recessed behind the bezel. It allows the unit to be

reset in any of four different modes. For further information see Reset Modes on

page 41.

Menu button (see figure 6) — Recessed behind the bezel. It activates the on-screen

menus for setting up and calibrating the unit (see page 12).

Reset LED (see figure 6) — Recessed behind the bezel. It lights as an indicator for the

Reset modes. For further information see Reset Modes on page 41.

TLP 700TV Rear Panel Features and Connections

With Stand Attached

Figure 7. TLP 700TV Rear Features

LED lights

Network connector

Power connector

MTP connector

TLP 700MV and TLP 700TV • Panel Features 9

The following connections are available through the back panel when the stand is in place:

LED lights (see figure 7 on the previous page) —The Link LED lights green to indicate

a good network connection. The Activity LED blinks yellow when network activity

occurs.

Network connector (see figure 7) — Use straight-through twisted pair cable to

connect the TLP 700TV to a network switch or router. Use a crossover cable to connect

the panel directly to a PC. An Extron IP Link control interface must be connected to the

same network domain.

Power connector (see figure 7) — Connect the provided power supply to this 2-pole

captive screw connector. See the Attention on page 7 for important information about

the power supply.

MTP connector (see figure 7) — Twisted pair input with RJ-45 connector provides

video and audio input.

ATTENTION:

• The left RJ-45 connector on the back of the TLP 1000TV (with the yellow and

green LEDs) must be connected to a network. The right RJ-45 connector

must be connected to an Extron MTP Transmitter. The MTP and LAN use

different voltages; switching the connectors will damage the touchpanel.

• Le connecteur RJ-45 gauche situé au dos du TLP 1000MV (avec des LED

jaunes et vertes) doit être connecté à un réseau. Le connecteur RJ-45 droit

doit être connecté à un émetteur MTP Extron. Le MTP et le LAN utilisent des

tensions différentes; permuter les connections risque d’endommager l’écran

tactile.

NOTE: Audio input is available only from an Extron MTP transmitter through

the RJ-45 connector in the base of the unit. If the base is removed from the

TLP700TV, connections are via BNC connectors and there is no audio input.

TLP 700TV Base Features

Figure 8. TLP 700TV Base Features

Adjustable Potentiomenters

Access for disconnecting

RJ-45 connectors

Security mounting holes

TLP 700MV and TLP 700TV • Panel Features 10

The TLP 700TV stand, which can be removed for VESA mounting, has:

Three adjustable potentiometers (see figure 8 on the previous page) — These

are used to control sharpness and gain for both S-video luminance (Y) and S-video

chrominance (C). If a composite video signal is used, the gain is controlled by the center

potentiometer (Vid/Y).

Gain

Vid/Y

Gain

Sharp

33-1814-01 A

Figure 9. TLP 700TV Potentiometers

Access for disconnecting RJ-45 connectors (see figure 8) — When RJ-45

connectors are covered with a protective boot, it can be difﬁcult to remove them from

their sockets. The two holes are directly underneath the two RJ-45 jacks (see figure7

on page 9). Push the tip of a pen or pencil through the holes to help disconnect the

RJ-45 connectors.

Security mounting holes (see figure 8) — If required, secure the unit to the

desktop, using two screws (see page 35).

Adjustable Potentiomenters

TLP 700MV and TLP 700TV • Panel Features 11

On-screen Menus

This section describes:

• How to Access the Internal On-screen Menus

• Main Screen

• Volume Screen

• Time Screen

• Network Screen

• Video Screen

• Touch Calibration Screen

How to Access the Internal On-screen Menus

When power is first applied to the TouchLink Panel, the unit boots up and displays the

opening screen. To access the on-screen menus, press the Menu button, located below

the screen (see figure 3, on page 5 for the TLP700MV or figure 6, on page 8 for the

TLP700TV).

The menus open at the Main screen. There are five screens (Main, Volume, Time,

Network, and Video) that can be selected by pressing the appropriate button at the left

side of the screen.

There is also an Exit button at the bottom left corner of the screen for leaving the menus.

Main Screen

Figure 10. Main Screen

Sleep timer determines how long the panel is inactive before it enters Sleep mode, when

the screen goes dark to save power. Press the Down or Up buttons to highlight the Sleep

timer options and continue to use the buttons or use the front panel volume control knob

to adjust the time from 0 to 50,000 seconds (in 10-second increments). The time that is

currently selected is shown above the buttons.

TLP 700MV and TLP 700TV • On-screen Menus 12

The screen may need a high level of backlighting to read the screen when ambient lighting is

high. With low ambient lighting, the backlighting should also be low.

Auto Backlight provides a suitable amount of backlighting that is automatically calculated

from the amount of ambient light detected by the light detector.

When Auto Backlight is set to Off, the Backlight option allows the backlighting to be set

manually from 0 to 100%. Press the Down or Up buttons to highlight the Backlight options

and use the volume control knob or press the Down or Up buttons to adjust the backlighting.

The current value is shown above the buttons.

NOTE: When Auto Backlight is set to On, changing the percentage of Backlight

does not affect the amount of backlighting.

LED Backlight lights the ten buttons next to the screen.

Wake on Motion activates the panel from Sleep mode when motion is detected near the

unit.

Use the on-screen buttons to toggle the Auto Backlight, LED Backlight, or Wake on

Motion options between Off and On.

Volume Screen

Figure 11. Volume Screen

Click on the Down or Up buttons to highlight one of the adjustable audio features. Use the

Down and Up buttons or the volume control knob to adjust:

Master volume (between 0 and 255) sets the maximum volume for all the other sound

volume settings. For example, if the master volume is set to 200 (approximately 80% of

maximum), even when the Line In volume is set to 255 (maximum), it is only equivalent to

80% of maximum.

Click (between 0 and 255) sets the volume for audible feedback that accompanies events

such as a side button or screen button being pressed.

Sounds (between 0 and 255) sets the volume of audio from an audio file playback.

Line In (between 0 and 255) sets the volume of the audio signal received through the line

in from and Extron MTP transmitter.

TLP 700MV and TLP 700TV • On-screen Menus 13

Time Screen

Figure 12. Time Screen

Click on the Down or Up buttons to highlight one of the adjustable time settings. Use the

buttons or the volume control knob to adjust the Month, Day, Year, Hours, and Minutes.

NOTE: The Hours value uses the 24 hour clock. For 10 am, set Hours to 10; for

10pm, set Hours to 22.

Network Screen

Figure 13. Network Screen

Set the IP Address or Subnet Mask by pressing the appropriate button. An on-screen

keypad appears that allows you to enter digits from 0 through 9 or “.” (dot). In the event of

an error, you can clear the field.

NOTE: The factory default IP address for the TLP 700MV is 192.168.254.254. The

default subnet mask is 255.255.0.0. Consult with your IT Department to ensure these

addresses are correctly assigned.

Toggle between On and Off to enable or disable Dynamic Host Configuration Protocol

(DHCP). This determines whether the unit has a permanent IP address or has one provided

by the network, when required. The default setting is off.

TLP 700MV and TLP 700TV • On-screen Menus 14

Page is loading ...

Extron TLP 700TV, TLP 700MV User manual

Related papers

Other documents