CTC Union ITP-1204GTM-12PHE Quick Installation Manual

1

Quick Installation Guide

sales@ctcu.com

ITP-1204GTM-12PHE

ITP-1204GTM-12PHE-BP

12 x 10/100Base-TX M12 + 4 x GbE M12 with 12 x PoE (120W,

24/48/72/110VDC)

12 x 10/100Base-TX M12 + 4 x GbE M12 with 12 x PoE & Built-

in Bypass Function (120W, 24/48/72/110VDC)

1

Version 1.0 February, 2020

T +886-2-26591021

F +886-2-26590237

E [email protected]m

H www.ctcu.com

2020 CTC Union Technologies Co., LTD.

All trademarks are the property of their respective owners.

Technical information in this document is subject to change without notice.

CTC Union Technologies Co.,Ltd.

Far Eastern Vienna Technology Center

(Neihu Technology Park)

8F, No. 60 Zhouzi St.,

Neihu, Taipei 114, Taiwan

3

Table of Contents

Introduction .................................................................................. 4

Package List ................................................................................. 4

Features ........................................................................................ 4

Access to Command Line Interface (CLI) ................................... 5

CONSOLE CONNECTION .......................................................................................... 5

TELNET/SSH CONNECTION ..................................................................................... 6

Access to Web-Based Management Interface ............................ 7

Specifications ............................................................................... 8

INTERFACE .......................................................................................................... 8

SWITCH ............................................................................................................. 8

POWER OVER ETHERNET ......................................................................................... 8

POWER .............................................................................................................. 8

MECHANICAL ...................................................................................................... 9

ENVIRONMENTAL ................................................................................................. 9

CERTIFICATIONS ................................................................................................... 9

MTBF (MIL-HDBK-217) ..................................................................................... 9

Panels ......................................................................................... 10

ITP-1204GTM-12PH ........................................................................................ 10

ITP-1204GTM-12PH-BP ................................................................................... 11

PIN Assignment .......................................................................... 12

M12 FAST ETHERNET PORT (D-CODE) ..................................................................... 12

M12 GIGABIT ETHERNET PORT (X-CODE) ................................................................. 12

M12 CONSOLE PORT ........................................................................................... 13

M12 ALARM PORT .............................................................................................. 13

M23 POWER INPUT PORT ..................................................................................... 13

M12 Cable Connector Installation ............................................. 14

Earth Ground Connection .......................................................... 16

LED Indicators ............................................................................ 17

Wall-Mounting Installation ......................................................... 18

Application .................................................................................. 19

4

Introduction

The ITP-1204GTM-12PH & ITP-1204GTM-12PH-BP are managed

Industrial Grade Ethernet PoE+ switches that provide 12 x 10/100Base-

TX Fast Ethernet UTP plus 4 x 10/100/1000Base-T with 12 PoE ports. ITP-

1204GTM-12PH & ITP-1204GTM-12PH-BP switches equipped with PoE

(Power over Ethernet) function utilize M12 connectors to ensure tight

and robust connections as well as to guarantee reliable operation

against environmental disturbances such as vibration and shock.

Housed in rugged and wall mountable housing, these Ethernet

switches are able to protect against dust and water submersion. Besides,

these switches comply with EN50155 standard that covers strict

demands on operating temperature, power input voltage, surge, ESD,

vibration, and shock, thus making them suitable for industrial

applications such as vehicle, rolling stock and railway.

Package List

 One switch device

 Protective caps for UTP, console and alarm ports

 Console cable (M12 to DB9)

Features

 Use M12/M23 anti-vibration and anti-shock connector

 M12 X-Code for Gigabit ports

 PoE output power budget 120W (max.)

 Support Cable diagnostics function and identify opens/shorts distance

 Support STP, RSTP, MSTP, ITU-T G.8032 (ERPS) and proprietary μ-Ring

for redundant cabling protection

 μ-Ring for Redundant Cabling, recovery time <10ms in 250 devices

(max.)

 Support TTDP for train application

 Support IEEE 1588 PTP V2 for precise time synchronization function

 Provide SmartConfig for quick and easy mass configuration

 Support SmartView for centralized management

 CE, FCC, EN50155, EN45545-2, EN50121-4, EN60950-1 certified

 Industrial grade EMS, EMI, EN61000-6-2, EN61000-6-4 certified

5

Access to Command Line Interface (CLI)

The ITP-1204GTM-12PH & ITP-1204GTM-12PH-BP are managed

Ethernet PoE+ switches for industrial uses. Initial configurations can be

accomplished via the M12 CONSOLE port and a PC or laptop running

terminal emulation software or via the M12 Ethernet port running

Telnet or SSH.

Accessing the switch via CONSOLE or Ethernet port allows the user

to use Command Line Interface (CLI) to manage and configure the device.

This management method is relatively useful when you lose the network

connection to the device. In most configuration scenarios, the console

will only be used to initially configure the IP address, so that the device

may be accessed via the other methods which require working TCP/IP.

See below for useful information for accessing the device via console

and Telnet/SSH connection.

Console Connection

Use the provided accessory cable to connect the "CONSOLE" port

to the PC terminal communications port (DB9). Run any terminal

emulation program (HyperTerminal, PuTTY, TeraTerm Pro, etc.) and

configure the communication parameters as follows:

Speed:

115,200

Data:

8 bits

Parity:

None

Stop Bits:

1

Flow Control:

None

From a cold start, the following screen will be displayed. At the

"Username" prompt, enter “admin” with no password.

To change the default IP address to your desired one (for example,

192.168.0.10/24), issue the following commands:

For complete CLI operation, please refer to the operation manual.

#

# config terminal

(config)# interface vlan 1

(config-if-vlan)# ip address 192.168.0.10 255.255.255.0

Press ENTER to get started

Username: admin

Password:

#

6

Telnet/SSH Connection

To use Command Line Interface (CLI), you can also choose

to access the device through a Telnet/SSH connection via TCP/IP

network over Ethernet ports. For initial operation, use the default TCP/IP

settings (10.1.1.1) to login to the device.

Default TCP/IP settings:

IP Address:

10.1.1.1

Subnet Mask:

255.255.255.0

Username:

admin

Password:

No password (Press "Enter"

key)

To change the default IP address to your desired one (for example,

192.168.0.10/24), issue the following commands:

Once the desired IP address has been configured, a web browser

can be accessed and used to configure the device through a more easy-

to-use GUI (graphical user interface). For complete CLI operation, please

refer to the operation manual.

#

# config terminal

(config)# interface vlan 1

(config-if-vlan)# ip address 192.168.0.10 255.255.255.0

7

Access to Web-Based Management Interface

To enter the web-based management interface for the first time

or after returning the device back to factory defaults, input the default IP

address “10.1.1.1” in your web browser. Then, a standard login prompt

will appear depending on the type of browser used. The example below

is with Firefox browser.

Enter the factory default username “admin” with no password.

After successfully entering the web based management, the Port State

page will appear. For complete Web GUI operation, please refer to the

operation manual.

8

Specifications

Interface

 12 x 10/100Base-TX UTP(M12, 4-Pin, D-Code Female) +

4 x 10/100/1000Base-T UTP (M12, 8-Pin, X-Code Female)

 Port 15 & 16 support bypass function (ITP-1204GTM-12PH-BP Series

only)

 Support Auto MDI/MDI-X

 Support Full/Half Duplex

 IEEE 802.3x Flow Control for full duplex; Back pressure for half duplex

mode

 Store & Forward mode

Switch

 MAC Address Table: 8K

 Packet Buffer Size: 512KB

 Jumbo Frame: 9.6KB

 Switching Fabric: 12.4Gbps

Power over Ethernet

 12 x PoE enabled ports, M12 (4-Pin) D-Code female connector

 End-Span Alternative A Mode

 Supports IEEE802.3af 15.4watts PoE per port

 Supports IEEE802.3at 30watts PoE+ per port

 Maximum PoE output power budget 120W (30W per port)

 Regulated PoE voltage at 52VDC

 Pin Assignments: 2 & 4 pins (V+); 1 & 3 pins (V-); 1, 2, 3, 4 (Data)

Power

 M23 (5-Pin) male power connector

 Support redundant dual 24/48/72/96/110VDC (16.8~137.5VDC) input

power

 Support power input reverse polarity protection

 Support overload current protection

 Consumption:

Items

Input Voltage

Total Power

Consumption

Device Power

Consumption

PoE Budget

24VDC

141.4W

13W

120W

48VDC

137.9W

14W

120W

110VDC

136.4W

16.5W

120W

9

Mechanical

 Housing: IP54 grade rugged metal housing protection

 Fanless design

 Dimensions: 113 mm (D) x 260 mm (W) x 132 mm (H)

 Installation Method: Wall-mounting

 Weight: 2.8kg

Environmental

 Operating Temperature: -40°C~75°C

 Storage Temperature: -40°C~85°C

 Humidity: 5%~95% (Non-condensing)

Certifications

 EMC: CE (EN55024, EN55032)

 EMI (Electromagnetic Interference): FCC Part 15 Subpart B Class A, CE

 Railway Traffic: EN50155, EN50121-4

 Fire Protection of Railway Vehicle: EN45545-2

 Immunity for Heavy Industrial Environment: EN61000-6-2

 Emission for Heavy Industrial Environment: EN61000-6-4

 EMS (Electromagnetic Susceptibility) Protection Level:

 EN61000-4-2 (ESD) Level 3, Criteria B

 EN61000-4-3 (RS) Level 3, Criteria A

 EN61000-4-4 (Burst) Level 3, Criteria A

 EN61000-4-5 (Surge) Level 3, Criteria B

 EN61000-4-6 (CS) Level 3, Criteria A

 EN61000-4-8 (PFMF, Magnetic Field) Field Strength: 300A/m,

Criteria A

 Safety: EN60950-1

 4KV Surge Protection: PoE and UTP ports

 Shock: IEC 61373

 Freefall: IEC 60068-2-32

 Vibration: IEC 61373

MTBF (MIL-HDBK-217)

 238,600 Hours

10

Panels

ITP-1204GTM-12PH

Index No.

Description

1

M12 D-Code Fast Ethernet Port 1~12

2

M12 X-Code Gigabit Ethernet Port 13~16

3

M12 Console Port

4

M12 Alarm Port

5

M23 Power Input Port

6

Power 1 & 2, Fault, ACT, Ring LED Indicators

7

Link/ACT & PoE LED Indicators for M12 Fast

Ethernet Port 1~12

8

Link/ACT LED Indicators for M12 Gigabit Ethernet

Port 13~16

9

Pin Assignment Tables for Console, Alarm & Power

Input Port

10

Pin Assignment Tables for Port 1~12 & 13~16

11

Wall Mounting Holes

12

Earth Grounding

Figure 1. ITP-1204GTM-12PH Front Panel

1

2

7

11

10

9

5

3

4

6

12

11

8

11

ITP-1204GTM-12PH-BP

Index No.

Description

1

M12 D-Code Fast Ethernet Port 1~12

2

M12 X-Code Gigabit Ethernet Port 13~16 (Port 15

& 16 are built-in bypass ports)

3

M12 Console Port

4

M12 Alarm Port

5

M23 Power Input port

6

Power 1 & 2, Fault, ACT, Ring LED Indicators

7

Link/ACT & PoE LED Indicators for M12 Fast

Ethernet Port 1~12

8

Link/ACT LED Indicators for M12 Gigabit Ethernet

Port 13~16

9

Pin Assignment Tables for Console, Alarm & Power

Input Port

10

Pin Assignment Tables for Port 1~12 & 13~16

11

Wall Mounting Holes

12

Earth Grounding

Figure 2. ITP-1204GTM-12PH-BP Front Panel

1

2

7

11

10

8

9

5

3

4

6

12

PIN Assignment

M12 Fast Ethernet Port (D-Code)

Port 1~12 Fast Ethernet

PoE Pinout

M12 Pin

No.

Pinout

RJ-45 Pin No.

1

TX+

3

V-

2

RX+

1

V+

3

TX-

6

V-

4

RX-

2

V+

M12 Gigabit Ethernet Port (X-Code)

Port 13~16 Gigabit Ethernet

M12 Pin No.

Pinout

RJ-45 Pin No.

1

TDR0+

1

2

TDR0-

2

3

TDR1+

3

4

TDR1-

6

5

TDR3+

7

6

TDR3-

8

7

TDR2-

5

8

TDR2+

4

Model: CAB-M12DM4-RJ45

Table 2. Gigabit Ethernet Cable Pin Assignment

Model: CAB-M12XM8-RJ45

Table 1. Fast Ethernet Cable Pin Assignment

13

M12 Console Port

M12 Pinout

DB-9 (Female) Pinout

1

TX

2

RX

2

RX

3

TX

3

-

4

GND

5

GND

5

-

M12 Alarm Port

M12 Pin No.

Description

Color of

Open Cable

1

Black

2

Blue

3

-

Red

4

-

Orange

5

-

Yellow

M23 Power Input Port

M23 Pin No.

Pinout

Description

Color of Open Cable

1

V1+

24~110VDC

Black

2

V1-

Blue

3

C-GND

Green

4

V2+

24~110VDC

Brown

5

v2-

White

Table 4. Alarm Cable Pin Assignment

Table 3. Console Cable Pin Assignment

R1

Table 5. Power Cable Pin Assignment

Normal (Relay Closed)

Fault (Relay Open)

14

M12 Cable Connector Installation

Before assembling M12 open cable, make sure you have the

following M12 cable connector components (Model: M12D-M4 M12 D-

Code Male) and open cable at hand.

Assembly Steps:

Step 1. Insert the screw nut, O-ring, and housing into the cable in the

order shown in the figure below and keep them loose in this step.

Step 2. Strip the cable and the individual cores to fit the connector.

Insert the stripped wires into the opened contact clamps.

Figure 3. Insert Components into the Cable

Figure 4. Insert the Stripped Wires to Contact Clamps

Screw Nut

Housing

Male Contact

Connector

O-Ring

15

Step 3. Tighten the connector in clockwise direction, making sure that

the wires inside the connector are not twisted as the screwed housing is

assembled.

Figure 5. Tighten the Connector

16

Earth Grounding Connection

An earth grounding connection hole is provided on the lower

right-hand corner of the wall-mounting plate. Grounding the device can

help to release leakage of electricity to the earth safely so as to reduce

injuries from electromagnetic interference (EMI).

Prior to connecting to the power, it is important to connect the

ground wire to the earth. Follow steps below to install ground wire:

Step 1. Make sure you have the grounding screw and grounding cable

at hand.

Step 2. Unfasten the ground screw on the front panel.

Step 3. Attach the grounding screw to the ring terminal of the

grounding cable. Make sure that the grounding cable is long enough to

reach the earth.

Step 4. Use a screwdriver (or other tools) to fasten the grounding

screw on the earth ground hole securely.

Figure 6. Earth Grounding Connection

Ring-type

terminal

Fork-type

terminal

17

LED Indicators

LED

Color

Status

Description

PWR1

Green

On

Lit if power 1 is connected and

active.

PWR2

Green

On

Lit if power 2 is connected and

active.

Fault

Amber

On

Lit when one or more of the

programmable alarm conditions is

active.

(CPU) ACT

Green

On

During normal use, this LED will be

lit, indicating a healthy condition of

the running CPU.

Blinking

Blinking when firmware is being

upgraded.

Ring

Amber

On

Lit when this unit is the 'master' in

a fiber ring and all units are

configured for u-Ring or ERPS

(Ethernet Ring Protection

Switching or G.8032).

10M/100M

LNK/ACT

for Port 1~12

Green

On

Lit when the LAN connected speed

is 10M or 100M.

Blinking

Blinking when there is Ethernet

traffic.

100M/1000M

LNK/ACT

for Port 13~16

Green

On

Lit when the LAN connected speed

is 10M or 100M.

Blinking

Blinking when there is Ethernet

traffic.

Amber

On

Lit when the LAN connected speed

is 1000M.

Blinking

Blinking when there is Ethernet

traffic.

PoE

for Port 1~12

Green

On

Lit when the respective LAN port

has successfully negotiated PoE

and is supplying output power to

the remote connected PD device.

Off

PoE output is off.

18

Wall-Mounting Installation

The Ethernet Switch can be mounted on the wall using the

attached wall-mounting plate with four wall-mounting holes. The

installation is simple and easy. Before installing the Ethernet Switch on

the wall, you have to prepare four suitable wall screws for wall mounting.

Installation steps are as follows:

Step 1. Find a suitable place to wall-mount the Ethernet Switch and

remember to align the mounting holes with wall screws.

Step 2. Install four appropriate screws horizontally into the wall leaving

less than 0.5cm or 1/4 inch exposed.

Step 3. Hang the Ethernet Switch on the inserted screws and make sure

the Ethernet Switch is hung securely on the four inserted screws.

Figure 8. Hanging the Device on the Inserted Screws

Wall

Figure 7. Installing Four Wall-Mounting Screws

19

Application

Figure 9. Onboard Train Application for ITP Series

20

Version

Date

Description

1.0

2020/2/14

Preliminary version.

CTC Union ITP-1204GTM-12PHE Quick Installation Manual

This manual is also suitable for

CTC Union ITP-1204GTM-12PHE Quick Installation Manual

Related papers

Other documents