Kaba ED 100/250 User manual

ED50/ED100/ED250

Swing Door Operators

Installation in Overhead Concealed Header

Door Installation, Setup,

Troubleshooting and Maintenance

Instructions

DL4617-003 – 06-2023

| EN |

2ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Table of Contents

Table of contents 

 General information 

. General information 

 ED//ED OHC product

description 

 ED//ED OHC door configurations 

. OHC single door configurations 

. OHC pair door and double egress door

configurations 

 Technical data 

. ED//ED technical data 

. Operating specifications 

 Safety information 

 ED/ED/ED User interface 

. Overview 

.  button keypad and display 

. Operator status LEDs 

. Mode switch and Exit Only switch panel 

. ED/ED/ED automatic and

manual modes 

. Low and full energy doors 

 System accessories 

. System accessory electrical connections 

. System accessories 

 Terminal board connections 

 ED/ED/ED door signage 

. Full energy operator 

. Low energy operator 

. Door signage, full energy single swing

doors (ANSI/BHMA A.) 

. Door signage, low energy single swing

doors (ANSI/BHMA A.) 

. Door signage, full energy pair swing doors

(ANSI/BHMA A.) 

. Door signage, low energy pair swing doors

(ANSI/BHMA A.) 

. Door signage, full energy double egress

swing doors (ANSI/BHMA A.) 

. Safety label, automatic swing doors 

. Safety label, low energy swing doors 

Table of contents

 Parameters 

. ED/ED/ED OHC – viewing and

changing parameters 

. Configuration parameters 

. Driving parameters 

 System setup for single door installation 

. Set operator spring tension 

. Set braking circuit plug position 

. ED/ED/ED OHC power on 

. Set installation type parameter AS 

. Set door width parameter Tb 

. Set OHC reveal depth parameter rd =  

. Set door type parameter dL 

. Perform partial learning cycle to rotate

arm to door installation position 

 Single door installation 

. Customer supplied single door -

installation 

. Prepare top of door for overhead arm 

. Prepare door for bottom door pivot and

install pivot 

. Install floor pivot shaft bearing 

. Hang door 

. Perform learning cycle 

 Set power fail closing speed 

. Set power fail closing speed 

 Pair door installation 

. Customer supplied doors - pair door

installation 

. Perform learning cycle for each door 

. Set power fail closing speed 

 Pair door parameters, Sync cable 

. Set ED operator parameters for pair door

operation 

. Connect Sync cable between

ED/ED/ED operators 

 Connect accessory wiring 

. Connect accessory wiring, single door 

. Connect accessory wiring, double doors 

 Install door signage, header cover 

. Install door signage 

. Install header cover 

3

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Table of Contents

 ANSI/BHMA standards 

. Power operated pedestrian doors

(ANSI/BHMA .) 

. Low energy power operated doors

(ANSI/BHMA A.) 

 Upgrade cards 

. Upgrade cards 

. Container module 

. Installing upgrade cards 

 Maintenance 

. ED/ED/ED environment and

cleaning 

. Overhead arm and bottom door pivot 

. ED brake maintenance 

Appendix A - Driving parameters 

A. Driving parameters – detail 

Appendix B - Troubleshooting 

B. Information and error codes 

B. Red LED status codes 

B. Troubleshooting chart, "ln" codes 

B. Troubleshooting chart, "E" codes 

Appendix C - dormakaba handheld 

C. dormakaba handheld terminal 

C. New dormakaba handheld; language

change to English 

C. dormakaba handheld; firmware update 

4ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 1

.. Door Installation, Setup, Maintenance and

Troubleshooting Instructions.

This manual provides Setup, Maintenance and

Troubleshooting instructions for ED/ED/ED

overhead concealed (OHC) header door

configurations.

.. OHC header Installation Instructions.

Reference ED/ED/ED OHC Installation

Instructions DL-.

.. ED/ED/ED OHC header Installation.

NOTICE

Exterior door use.

To insure proper suitability for exterior door

use, the following topics must be addressed in

the context of the door application setting.

• Site-specific use factors such as high wind

conditions and/or building pressure.

• Door width, height, weight, and usage

patterns.

• Observable prevailing conditions at the

opening under which the operator is

expected to perform. In some instances, this

may require increased force settings to

counteract these conditions.

• Door mounted presence sensors.

When attempting to overcome these forces,

it is strongly suggested that door mounted

presence sensors be employed to enhance

pedestrian safety through the opening.

.. Manual storage.

This document must be kept in a secure place, and

accessible for reference as required.

If the door system should be transferred to another

facility, insure that this document is transferred as well.

.. dormakaba.us website.

Manuals are available for review, download, and printing

on the dormakaba.us website.

.. Dimensions

Unless otherwise specified, all dimensions are given in

both inches (“) and [mm].

 General information

. General information

.. Symbols used in these instructions.

WARNING

This symbol warns of hazards which could result

in personal injury or threat to health.

CAUTION

This symbol warns of a potentially unsafe

procedure or situation.

NOTICE

Draws attention to important information

presented in this document.

TIPS AND RECOMMENDATIONS

Clarifies instructions or other information

presented in this document.

Fig. 2.1 ED50/ED100/ED250 OHC with overhead arm

5

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 2

 ED//ED OHC product

description

Fig. 2.2 ED100/ED250 OHC operator

Fig. 2.5 Overhead arm

TIPS AND RECOMMENDATIONS

Insure ED50/ED100/ED250 OHC header

installation is qualified for use at the respective

smoke or fire-rated door.

NOTICE

Door jambs, door(s) and installation by

customer.

. Intended use.

ED/ED/ED are electromechanical operators

used exclusively for opening and closing interior or

exterior swing doors. Reference Para. ...

. Packaging

ED/ED/ED operators are packaged in a

header for overhead concealed (OHC) installation.

For pair swing doors, two ED/ED/ED

operators are packaged in a single header.

. ED/ED/ED operators.

.. ED

• Supplied only as a low energy operator.

(ANSI/BHMA A.).

.. ED

• Supplied as a low energy operator.

(ANSI/BHMA A.).

• Configured as a full energy operator (ANSI/BHMA

A.) using parameter adjustment.

.. ED

• Supplied as a low energy operator.

(ANSI/BHMA A.).

• Configured as a full energy operator (ANSI/BHMA

A.) using parameter adjustment.

. ED/ED/ED separate modules (Fig. .).

.. Single door header; modules supplied:

• Low voltage wiring connection module.

• Main power module.

.. Pair door header; modules supplied:

• Two low voltage wiring connection modules.

• Two main power modules. Fig. 2.4 Wiring module Main power module

NOTICE

Door weights and ED operator low energy

requirements.

•  to  pounds: It is recommended the

ED operator(s) be configured for low energy.

•  to  pounds: The ED operators must

be configured for low energy.

. Maximum door weights*.

*Maximum door weight is based on prevailing conditions

at the door opening.

Door width ED

maximum door

weight

ED

maximum

door weight

ED

maximum

door weight

Inches mm Pounds - kg Pounds - kg Pounds - kg

 .      

 .      

       

       

Fig. 2.3 ED50 OHC operator

6ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 3

 ED//ED OHC door configurations

. OHC single door configurations

Fig. 3.1.1 LH inswing RH inswing Fig. 3.1.2 LH outswing RH outswing

Fig. 3.2.4 RH double egress

Fig. 3.2.3 Inswing

Fig. 3.2.1 Outswing

Fig. 3.2.2 LH double egress

. OHC pair door and double egress door configurations

Jambs and doors supplied and installed by customer.

Locks optional.

7

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 4

 Technical data

Maximum wire size

Connector plug

screw size

 AWG

/”

Door

status

X

,,

Sr parameter

Door closed

Door open

Door closed, locked

Com, N.O., N.C.

contacts

.. Integrated functions.

Hold open time

Automatic opening dd parameter  to  s

Optional  -  s.

Hold open time

NIght / bank dn parameter  to  s

Hold open time

Manual opening do parameter  to  s

Door blocking

behavior hd parameter Automatic, manual

door modes

Electric strike

delayed opening for

locking mechanism

Ud parameter  to  s

Locking

device

feedback

X

,  Chapter  Motor lock

Wind load control,

maximum Fo, Fc parameters . lb f

 N

Voltage independent

braking circuit Chapter  Adjustable with

potentiometer

LED status indicators

Green, Red, Yellow

Chapter 

 Vdc power

Error codes

Service interval

Mode and Exit Only

switches

Auto, Close, Open

Exit only; Off, On

User interface  button keypad,

 digit display

Slot for upgrade

cards Chapter  Extension of

functional range.

Firmware update Firmware update

TMP, temperature

management program

Overload

protection

IDC, initial drive control Driving phase optimization

Cycle counter CC parameter  to ,,

Power assist function hA, hF, hS

parameters

Drive support for

manual opening of

door

Push & go function PG parameter Auto opening of

door at ° open

. ED//ED technical data

.. Required operating conditions.

Ambient temperature  to  °F [- to  C]

Suitable for dry

rooms only

Relative air humidity:

% maximum, non-condensing

Power supply  Vac ±%, / Hz

. A maximum

Branch circuit

protection (provided

by others)

 A maximum,

dedicated branch circuit

Protection class NEMA  [IP]

Power wiring:

black, white, bare

copper (ground)

 AWG

maximum

Operating noise Maximum  db(A)

.. General specifications.

Operator dimensions

(W x H x D)

" x  / x  /" [ x  x  mm]

" cover standard

Operator weight . lb [. kg]

ED: Power supply

for accessories Separate power supply required.

ED/ED:

Power supply for

accessories

 Vdc ± %, . A.

Maximum door

opening angle  to ° depending on installation type

.. Inputs

Wire size

Connector plug

screw size

 AWG

/”

Activation

inputs X* Interior, exterior N. O. contact

Safety

sensors X Swing, approach sides.

Night-bank

(intercom

system)

X

,

a

- Vdc/Vac +%

Night-bank

(key switch)

X

,  d parameter Configure for N.O.

or N.C. contact

Deactivation

of drive

function

X

, a d parameter Configure for N.O.

or N.C. contact

.. Outputs

*X: terminal board numbers, reference Chapter ,

Terminal board connections.

8ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 4

. Operating specifications

Maximum power

consumption  watts

Opening force

lbf - N

Fo parameter

Minimum

. []

Maximum

. []

Manual closing force

lbf - N

Fc parameter

Minimum

. []

Maximum

. []

Maximum door

weight, lb [kg]  [ kg)*

*Based on prevailing

conditions at the door

opening.

Door width Minimum

"

Maximum

"

Maximum opening

speed, °/s  May be limited by

door weight after

learning cycle.

Maximum closing

speed, °/s 

.. ED

.. ED

Maximum power

consumption  watts

Automatic opening

torque

Minimum

 N m

. lbf ft

Maximum

FE:  N m

. lbf ft

LE:  N m

. lbf ft

Automatic closing

torque

Minimum

 N m

. lbf ft

Maximum

FE:  N m

. lbf ft

LE:  Nm

. lbf ft

Manual closing

torque

Minimum

 N m

. lbf ft

Maximum

 N m

 lbf ft

Maximum door

weight

 pounds at a maximum door width

of  inches.*

*Based on prevailing conditions at the

door opening.

Door width " to ”

Door width for fire

protection " to ”

Maximum opening

speed, °/s Note 

FE: 

LE: 

Maximum closing

speed, °/s Note 

FE: 

LE: 

Maximum power

consumption  watts

Automatic opening

torque

Minimum

 N m

. lbf  ft

Maximum

FE:  N m

. lbf ft

LE:  Nm

. lbf ft

Automatic closing

torque

Minimum

 N m

. lbf  ft

Maximum

FE:  N m

. lbf ft

LE:  N m

. lbf ft

Manual closing

torque

Minimum

 N m

. lbf ft

Maximum

 N m

 lbf ft

Maximum door

weight

 pounds at a maximum door width

of  inches.*

*Based on prevailing conditions at the

door opening.

Ref: Para. . for low energy

requirements.

Door width " to ”

Door width for fire

protection " to ”

Maximum opening

speed, °/s Note 

FE: 

LE: 

Maximum closing

speed, °/s Note 

FE: 

LE: 

.. ED

Note 

Full energy / low energy

• FE: ED/ED configured for full energy.

• LE: ED/ED configured for low energy.

Note 

Depending on door panel weight, automatically limited with low

energy power operator doors (ANSI A.).

Maximum speeds will only be reached in full energy operating mode,

low door panel weight, and a minimum learned opening angle of

.

9

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 5

. Safety instructions.

This document contains important instructions for

installation of the ED/ED/ED overhead

concealed swing door operator.

Review these instructions thoroughly prior to

installation, and follow them carefully during

installation, commissioning, troubleshooting and

maintenance.

. Door signage requirements.

Proper signs and labels shall be applied and

maintained on the door controlled by the

ED/ED/ED overhead concealed swing

door operator as referenced in:

• ANSI/BHMA A.: Standard for power

operated doors.

• ANSI/BHMA A.: Standard for power assist

and low energy power operated doors.

• Reference Chapter , Door signage.

. Safety warnings.

WARNING

Damage to equipment or incorrect equipment

operation may result from an incorrect installation.

WARNING

Hazard to mechanical processes by use of

control settings, elements, or procedures not

documented in this manual!

WARNING

Electric shock hazard!

By use of control elements, settings, or

procedures not documented in this manual!

WARNING

Work on electrical equipment and  Vac

wiring installation must be performed only by

qualified personnel!

WARNING

Metallic doors must be grounded per national

and local codes!

 Safety information

WARNING

Hand pinch point and crushing hazards at door

closing edges!

WARNING

Crushing hazards at door closing edges!

. Residual hazards.

WARNING

After installation, hazards such as minor

crushing, impact with limited force, and risk to

unsupervised children may exist depending on

structural design of door area, type of door,

and any safeguards that have been

implemented.

Fig. 5.1 Door closing edges

Opposing

closing edge

Main

closing edge

Secondary

closing edge

10 ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 6

 ED/ED/ED User interface

. Overview

Fig. 6.2.1 Door hinge side on right

2 2 digit display

5 Button legend

Fig. 6.2.2 Door hinge side on left

.  button keypad and display

Right button

. Access parameter menu,

press button >  seconds.

. Edit selected parameter.

. Save changed value.

Left button . Reset, > s

. Quit process, <  s.

Both buttons

together

. Acknowledge errors,

press both buttons <  s.

. Reset, press both

buttons >  s.

Up button

. Scroll through parameters

and error messages.

. Increase parameter value.

Down button

. Scroll through parameters

and error messages.

. Reduce parameter value.

. Opening pulse, press

button <  s.

. Learning cycle, press

button >  s.

. Reset with factory setting,

press button >  s (program

switch Close position).

. Identify operator

orientation for display

2 2 digit display

6 Button legend

rotated 180°

..  button keypad.

 button legend is orientated so buttons

have same function and position regardless

of operator orientation. Button legend can

be removed and rotated.

..  button keypad functions.

TIPS AND RECOMMENDATIONS

Symbols

• "<", Less than.

• ">", Greater than.

> 3s Reset

< 3s Quit

> 3s

PRG

< 3s LEARN

Fact-Setup

> 3s

> 8s

2

5

> 3s Reset

< 3s Quit

LEARN

< 3s

> 3s

Fact-Setup

PRG

> 3s

> 8s

6

2

1 4 button keypad

and 2 digit display

Fig. 6.1.1 OHC ED100/ED250 operator

1

1 4 button keypad

and 2 digit display

Fig. 6.1.2 OHC ED50 operator

1

11

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 6

. Operator status LEDs

Fig. 6.3.1 Operator status LEDs, header cover removed .. Operator status LEDs.

. Red LED

Blinking codes are used to indicate "ln__" information

(system status or operating conditions) or certain

error codes "E__".

. Yellow LED

Maintenance interval indicator. When illuminated, an

indication the operator system has to be serviced.

. Green LED

• On, internal  Vdc power is On.

• Off, internal  Vdc power is Off.

TIPS AND RECOMMENDATIONS

Details on LED status codes and maintenance

intervals can be found in Appendix B –

Troubleshooting.

1 Red LED

2 Yellow LED

3 Green LED

1

2

3

45

6

4 Accessory terminal

board

5 OHC header

6 Power Off/On

switch

12 ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 6

. Mode switch and Exit Only switch panel

.. Mode switch position descriptions.

Auto

. Door opens automatically when one of the activators

is actuated or triggered.

Door closes on expiration of adjustable hold open

time with no activators or actuators triggered.

. With knowing act device actuation (Para. ..).

Door will remain at full open position for not less

than  seconds.

. With push/pull actuation of door (Para. .).

Door will remain at full open position for not less than

 seconds.

Close

. Door will remain closed, or if door is open door will

close.

Open

. Door opens automatically and remains open.

.. Exit Only switch position descriptions.

On

. Exterior activation sensor or knowing act device

disabled when door fully closed.

• Only interior activation sensor or knowing act device

will enable door opening.

Off

. Both interior and exterior activation sensors or

knowing act devices will enable door opening.

.. Exit Only switch

positions.

1 Mode switch panel

2 Mode switch,

three position

1

2

4

3

Auto

Fig. 6.4.2 Auto

.. Mode switch

positions.

Close

Fig. 6.4.3 Close

Fig. 6.4.4 Open

Fig. 6.4.5 On

On

Off

Fig. 6.4.6 Off

Open

Fig. 6.4.1 Overhead concealed header

3 Exit only switch,

two position

4 RJ45 Comm port for

service

Fig. 6.4.7 Optional key switch panels

13

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 6

. ED/ED/ED automatic and manual modes

.. Automatic mode.

Manual/automatic mode parameter hd=.

Setting if door is opened automatically following pulse

generation by an activation or knowing act device.

.. Manual mode.

Manual/automatic mode parameter hd=.

Setting if door is opened manually most of the time and

only rarely automatically.

. Low and full energy doors

.. Low energy power operated door

(ANSI/BHMA A.).

. ED is supplied only as a low energy operator.

. ED and ED operator default is low energy.

F parameter = .

• Reference ANSI/BHMA A., Standard for Power

Assist and Low Energy Power Operated Swinging

Doors.

... Low energy power operated door definition.

A door with a power mechanism that opens the door

upon receipt of a knowing act activating signal, does

not generate more kinetic energy than specified in

ANSI 156.19, and is closed by a power mechanism or by

other means.

Required system safety, as a low energy application, is

achieved utilizing the following design factors:

• Reduced dynamic door panel contact forces.

• Reduced static door panel contact forces.

• Low driving speeds.

• Force limitation.

... Knowing act definition.

Any conscious action with the expected result of

opening a door. This includes but is not limited to:

• Wall or jamb mounted contact or non contact

switches such as pushplates.

• The action of of manually opening (pushing or

pulling) a door.

• Controlled access devices such as keypads, card

readers, wireless transmitters and key switches.

.. Power assist.

• Available only in manual mode (hd=). Drive support

is automatically adjusted to operator size.

• Parameter hA sets door activation angle for power

assist function. Once angle reached, drive support

provides easier manual opening of the door.

• Parameter hF, power assist function. Parameter

decreases the amount of force required to open the

door.

• Parameter hS, power assist function support for

door in closed position.

TIPS AND RECOMMENDATIONS

Parameter descriptions can be found in

Chapter 11; Parameters.

.. Power operated door (ANSI/BHMA A.).

ED and ED operators can be configured for full

energy (power operated door).

F parameter = .

... Power operated door definition.

The combination of door, operator, controls and sensors

constituting the system. (Also called automatic door.)

14 ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 7

 System accessories

. System accessory electrical connections

Fig. 5.1.1 Electrical connections, single door

.. Overview

ED/ED/ED operators are normally used with

system accessories available from dormakaba USA, Inc.

or other manufacturers.

.. Accessory electrical installation.

Electrical interfaces from system accessories used with

operator must be planned for. This includes routing of

wiring from accessories to operator.

.. System accessories, other

manufacturers.

dormakaba USA cannot guarantee compatibility for

other manufacturer's accessories. If any of these

accessories are used despite this caution, the operator's

full range of functions may be unavailable, or the

accessories may not function properly.

WARNING

Damage to operator or to connected device is

also possible!

.. ED power for accessories.

. Separate power supply required for accessories.

.. ED/ED power for accessories.

.  Vdc, . A ( watts) is available from the

operator for external consumers (Fig. ..). This

supply has overcurrent protection. If additional

power is required, an external power supply must be

used.

. System accessories

1 External mode

switch, mechanical

2 External mode

switch, electronic

3 Key switch

4 Pushbutton, night /

bank

5 Pushbutton, interior

6 Pushbutton, exterior

7 Door locking device

8 Manual release

switch

9 ED50/ED100/

ED250

.. Activators

Typical activators:

. Pushbuttons, key switches

. Access control systems

. Telephone systems

. Intercoms

. Sensor automatic activators (ANSI/BHMA A.).

TIPS AND RECOMMENDATIONS

Refer to Chapter 4, Technical data

for electrical interface requirements.

.. Locking devices.

Typical locking devices:

. Electric strike plates

. Electromagnetic locks

. Electric locks

To insure that operator and locking device work safely

when connected together, locking device mus comply

with following:

. Operating voltage, power supply from operator, 

Vdc, ± %.

. Operating voltage, external power supply,

 Vdc/Vac maximum.

. Locking device relay contact, maximum load,  A.

. Electric strike plate duty factor, % minimum.

. Motor lock duty factor, %.

1

8 x 18 AWG

8 x 0.8 mm2

2 x 18 AWG

2 x 0.8 mm2

2 x 18 AWG

2 x 0.8 mm2

2 x 18 AWG

2 x 0.8 mm2

4 x 18 AWG

4 x 0.8 mm2

2 x 18 AWG

2 x 0.8 mm2

2 x 18 AWG

2 x 0.8 mm2

2 x 18 AWG

2 x 0.8 mm2

3 x 12 AWG

3 x 4.0 mm2115 VAC power

2

4563

7

8

9

15

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 8

 Terminal board connections

Fig. 8.1.1 ED50/ED100/ED250 terminal board electrical connections

1 Green LED (Para. 4.4)

2 Yellow LED (Para. 4.4)

3 Red LED (Para. 4.4)

4 Key (red insert)

location in socket.

Assigned plug has

tab in same location

broken off.

5 Jumpers, factory

installed at following

terminals:

•  and a

•  and *

•  and *

6 DCW upgrade card

plug

7 Fire protection

upgrade card plug

TIPS AND RECOMMENDATIONS

• Use documentation provided

with each device for electrical

installation.

• It is recommended not to

connect system accessories to

board until after operator has

been setup and learning cycle

performed (Chapter ).

97 98 99 30 31 32 34 33 3335 136144a

3BA157 57a 14231413115 17 311113 3

43 36463621G 3

+ 24 V

Signal input

0 V

Partial Open

Permanent Open

Exit Only

Automatic

Off

N.C.

COM

Test output

X5X4

X3

X6 X9 X1 X7

+ 24 V

X8

0 V

X10

8 - 24 AC/DC

+ 5% Wet

DCW bus

Safety sensors

Activation inputs

Interior Exterior

Night-

bank

input

+ 24 V

Signal input

0 V

+ 24 V

Signal input

0 V

Test output

0 V

24 V

Brake coil

signal

Output

COM

N.O.

N.C.

0 V

Locking relay

Maximum current:

1A, 48 V DC/AC

Locking feedback contact

0 V

+ 24 V

0 V

Signal input

N.O.

Smoke

detectors

Emergency

close

Night

trigger

Mode, Exit Only

switches

Door status

24 VDC

Class II

1

2

3

4

5

6

7

5

ED50 ED100/ED250

0 V Maximum current

load: 1.5A

24 V

Swing side Approach side

Note : ED/ED: Terminals  and 

are also used for swing side overhead sensor

input when parameter ST is set to  or .

Reference Appendix A, Parameters.

16 ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 9

 ED/ED/ED door signage

Signage and warnings are specified in

ANSI /BHMA A., American National Standard for

Power Operated Pedestrian Doors, paragraph .

.. Door, one way traffic, Fig. ...

. Arrow and AUTOMATIC DOOR, one side of decal.

• Shall be visible from approach side of a swinging door,

mounted on door at a height of " ± " from floor to

centerline of sign.

. DO NOT ENTER and AUTOMATIC DOOR, one side of

decal (or separate decal for solid doors - DD-).

• Shall be visible from non-approach side of door that

swings towards pedestrians attempting to travel in

wrong direction.

.. Door, two way traffic, Fig. ...

. Arrow and AUTOMATIC DOOR, one side of decal.

• Shall be visible from approach side of a swinging door,

mounted on door at a height of " ± " from floor to

centerline of sign.

. CAUTION AUTOMATIC DOOR, one side of decal.

• Swinging doors serving both egress and ingress shall

have a "CAUTION AUTOMATIC DOOR" sign visible

from swing side of door.

• Sign shall be mounted on door at a height of  ± "

from floor to centerline of sign.

.. Overview Fig. 9.1.1 One decal, approach side, non-approach side

. Full energy operator

Fig. 9.1.2 One decal, two way traffic

Fig. 9.1.3 ACTIVATE SWITCH TO OPERATE decal

DD-

DD-

DD-

AUTOMATIC

DOOR

DD0758-010

ACTIVATE SWITCH

TO OPERATE

DD0758-010

AUTOMATIC

DOOR

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

CAUTION

DOOR

AUTOMATIC

DD0756-010

dormakaba

. Low energy operator

.. Overview

Signage and warnings are specified in

ANSI /BHMA A., American National Standard for

Power Assist and Low Energy Power Operated Doors.

.. All low energy doors.

. AUTOMATIC CAUTION DOOR decal.

• All low energy doors shall be marked with signage

visible from both side of door with the words

"AUTOMATIC CAUTION DOOR".

• Signs shall be mounted " ± " from floor to

centerline of sign.

.. Knowing act switch used to initiate door operation.

. ACTIVATE SWITCH TO OPERATE decal.

• When a knowing act device is used to initiate operation

of door operator, door shall be provided with sign on

each side of door where switch is operated with

message "ACTIVATE SWITCH TO OPERATE".

.. Push/Pull used to initiate door operation.

. PUSH TO OPERATE, PULL TO OPERATE decals.

• When push/pull is used to initiate operation of door

operator, doors shall be provided with the message

"PUSH TO OPERATE" on push side of door and

"PULL TO OPERATE" on pull side of door.

.. Knowing act door.

. ACTIVATE SWITCH TO OPERATE decal.

• Knowing act doors shall have signage stating

"ACTIVATE SWITCH TO OPERATE" on side of door

having knowing act switch or other knowing act device.

Fig. 9.2.1 AUTOMATIC CAUTION DOOR decal

Fig. 9.2.2 ACTIVATE SWITCH TO OPERATE decal

Fig. 9.2.3 PUSH TO OPERATE, PULL TO OPERATE decals

DD-

DD- DD-

CAUTION

DOOR

AUTOMATIC

DD0586-010 DD-

1 Activate Switch to

Operate DD0758-010

DD0758-010

ACTIVATE SWITCH

TO OPERATE

DD0758-010 1

2 Push to Operate

DD0762-010

3 Pull to Operate

DD0762-020

DD0762-010

PUSH

TO OPERATE 2

DD0762-020

PULL

TO OPERATE 3

17

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 9

Fig. 9.3.1 One decal, one way traffic

Approach Swing side

. Door signage, full energy single swing doors (ANSI/BHMA A.)

Fig. 9.3.3 One decal, two way traffic

. Door signage, low energy single swing doors (ANSI/BHMA A.)

Fig. 9.4.1 Knowing act device Fig. 9.4.2 Push/pull

Fig. 9.3.2 One way traffic

Approach Swing side

Fig. 9.3.4 Two way traffic

Approach side

Swing side

Approach side

Swing side

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

50” ± 12”

AUTOMATIC

DOOR

CAUTION

DOOR

AUTOMATIC

DD0756-010

dormakaba

50” ± 12”

AUTOMATIC

DOOR

50” ± 12”

CAUTION

DOOR

AUTOMATIC

DD0586-010

DD0758-010

ACTIVATE SWITCH

TO OPERATE

DD0758-010

ACTIVATE SWITCH

TO OPERATE

DD0758-010

CAUTION

DOOR

AUTOMATIC

DD0586-010

DD0758-010

ACTIVATE SWITCH

TO OPERATE

DD0758-010

ACTIVATE SWITCH

TO OPERATE

DD0758-010

50” ± 12”

CAUTION

DOOR

AUTOMATIC

DD0586-010

DD0762-020

PULL

TO OPERATE

DD0762-020

PULL

TO OPERATE

CAUTION

DOOR

AUTOMATIC

DD0586-010

DD0762-010

PUSH

TO OPERATE

DD0762-010

PUSH

TO OPERATE

Pull to Operate Push to Operate

18 ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 9

. Door signage, full energy pair swing doors (ANSI/BHMA A.)

Fig. 9.5.1 One way traffic, approach side Fig. 9.5.4 One way traffic, swing side

Fig. 9.5.5 Two way traffic, swing side

Fig. 9.5.6 Knowing act, swing side, one way

Fig. 9.5.2 Two way traffic, approach side

Fig. 9.5.3 Knowing act, approach side, one way

50” ± 12”

AUTOMATIC

DOOR

AUTOMATIC

DOOR

50” ± 12”

AUTOMATIC

DOOR

AUTOMATIC

DOOR

50” ± 12”

AUTOMATIC

DOOR

AUTOMATIC

DOOR

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

50” ± 12”

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

50” ± 12”

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

50” ± 12”

CAUTION

DOOR

AUTOMATIC

DD0756-010

dormakaba

CAUTION

DOOR

AUTOMATIC

DD0756-010

dormakaba

19

ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 9

50” ± 12”

CAUTION

DOOR

AUTOMATIC

DD0586-010

CAUTION

DOOR

AUTOMATIC

DD0586-010

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

. Door signage, low energy pair swing doors (ANSI/BHMA A.)

Fig. 9.6.1 Knowing act device, approach side Fig. 9.6.3 Knowing act device, swing side

Fig. 9.6.4 Push/pull, door pull, swing sideFig. 9.6.2 Push/pull, door push, approach side

50” ± 12”

CAUTION

DOOR

AUTOMATIC

DD0586-010

CAUTION

DOOR

AUTOMATIC

DD0586-010

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

ACTIVATE SWITC

H

TO OPERATE

DD0758-010

50” ± 12”

CAUTION

DOOR

AUTOMATIC

DD0586-010

CAUTION

DOOR

AUTOMATIC

DD0586-010

DD0762-020

PULL

TO OPERATE

DD0762-020

PULL

TO OPERATE

DD0762-020

PULL

TO OPERATE

DD0762-020

PULL

TO OPERATE

50” ± 12”

CAUTION

DOOR

AUTOMATIC

DD0586-010

CAUTION

DOOR

AUTOMATIC

DD0586-010

DD0762-010

PUSH

TO OPERATE

DD0762-010

PUSH

TO OPERATE

DD0762-010

PUSH

TO OPERATE

DD0762-010

PUSH

TO OPERATE

Pull to Operate

Push to Operate

20 ED50/ED100/ED250 06-2023DL4617-003

dormakaba ED50/ED100/ED250 OHC Header

Setup and Troubleshooting Instructions

Chapter 9

. Door signage, full energy double egress swing doors

(ANSI/BHMA A.)

Fig. 9.7.2 RH double egress

Swing side Approach side

Fig. 9.7.3 RH double egress, exterior side

Approach side

Swing side

Fig. 9.7.6 LH double egress, exterior side

Fig. 9.7.5 LH double egress

Fig. 9.7.1 OHC RH double egress Fig. 9.7.4 OHC LH double egress

Swing side

Approach side

50” ± 12”

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

AUTOMATIC

DOOR

50” ± 12”

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

AUTOMATIC

DOOR

Approach side Swing side

50” ± 12”

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

AUTOMATIC

DOOR

50” ± 12”

DD0739-010

AUTOMATIC

DOOR

DO NOT

ENTER

AUTOMATIC

DOOR

Approach side

Swing side Approach side Swing side

Page is loading ...

Kaba ED 100/250 User manual

This manual is also suitable for

Kaba ED 100/250 User manual

Related papers

Other documents