2. Super Bright LEDS
  3. LCGP Series
LCGP Series

Super Bright LEDS LCGP Series User manual

  • I've reviewed the user manual for the LCGP series LED Parking Garage and Canopy Lights, specifically the LCGP-50KC-40W and LCGP-50KC-70W models. The manual provides detailed instructions for installation using surface, conduit or pole/pendant mounting, along with important safety precautions and wiring diagrams. I'm ready to assist you with any questions you may have about these lights or their installation process.
  • What is the operating temperature range?
    What is the IP rating of the light?
    Is this light dimmable?
LED Parking Garage and Canopy Light
Important: Read all instructions prior to installation. LCGP Series
User Manual
Rev Date: V0.1 10/11/2018
Dimensional Drawings
10.00in
254mm
10.00in
254mm
18in
457.2mm
3/4 in. thread
3.26in
82.8mm
WIRE
7.75in
196.85mm
5.20in
132.08mm
G3/4 THREAD
1.00in
25.40mm
.35in
8.89mm
.18in
4.55mm
1.37in
34.8mm
1.72in
43.69mm
2.37in
60.2mm
3.43in
87.12mm
4.81in
122.17mm
.18in
4.57mm
MOUNT
LCGP-50KC-70W
LCGP Series
User Manual
Rev Date: V1 09/30/2021
Specications
Safety and Notes
LED Canopy Light
Important: Read all instructions prior to installation.
Model LCGP-50KC-40W LCGP-50KC-70W
Operating
Temperature -4–113°F (-20–45 °C)
IP Rating IP65
Dimmable 0–10V
Weight 6 lb, 2 oz
• Product should be installed by a certied electrician in accordance with applicable national,
state, and local building and electrical codes.
• To reduce the risk of electric shock, ensure that main power source and circuit breakers
are switched o before performing any installation or wiring procedures.
• Avoid looking directly into lamp when illuminated.
• Ensure all mounts are securely attached and will support weight of the xture. Failure to
properly support the xture may result in damage or injury, for which the manufacturer
does not assume responsibility.
Wiring Diagram
Black
L L
N N
GND GND
White
Green
+ +
– –
Purple
Gray/Pink
Black
White
Green
Purple
Gray
100–277 VAC
Supply
0–10 V Dimmer
5yr
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
LCGP Series
User Manual
Rev Date: V1 09/30/2021 Rev Date: V1 09/30/2021
Conduit Installation
Surface Mounting Installation
Pole/Pendant Mounting Installation
LED Parking Garage and Canopy Light
1. Remove supply power.
2. Cap unused wires exiting top/rear of xture.
3. Remove desired conduit plug(s).
4. Remove eight screws holding lens in place and carefully remove lens.
5. Remove the three screws holding the internal bae in place and remove
the bae.
6. Remove the three wires (L, N, and G) from the input side of the terminal
block and cap the unused wires on the inside of the xture.
Note: The exterior wiring may need to be trimmed down.
7. If using dimmer, remove the dimmer wires from the wire caps and cap
the unused wires.
8. Run wire through and connect conduit to 3/4” threaded hole(s) with
adequate wire lead to make internal connections.
9. Connect supply wiring (L, N, and G) to terminal block and connect dimmer
wiring to dimmer circuit.
10. Reinstall internal bae and lens, then reapply supply power.
1. Remove retaining screw and slide mounting plate o of light.
2. Attach mounting plate to junction box.
3. Use hanger on the mounting plate to hold light in place and connect
wiring. See “conduit installation” section if wiring through conduit.
4. Slide lamp onto mounting plate.
5. Reinstall retaining screw.
1. Connect wiring.
2. Thread light onto pole/pipe until secure.
screw
hanger
mounting plate
screw
screws
junction box
G3/4" steeve
G3/4" thread
screw
hanger
mounting plate
screw
screws
junction box
G3/4" steeve
G3/4" thread
L
G
N
3
3
4
5
6
7
8
8
9
9
/