H3C SR6604 Installation guide

H3C SR6608/6604 Routers

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: T2-08040D-20080516-C-1.02

No part of this manual may be reproduced or transmitted in any form or by any means

without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF, NetPilot,

Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,

Storware, NQA, VVG, V

2

G, V

n

G, PSPT, XGbus, N-Bus, TiGem, InnoVision and

HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their

respective owners.

Notice

The information in this document is subject to change without notice. Every effort has

been made in the preparation of this document to ensure accuracy of the contents, but

all statements, information, and recommendations in this document do not constitute

the warranty of any kind, express or implied.

To obtain the latest information, please access:

http://www.h3c.com

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C SR66 Series Routers documentation set includes

the following:

Manual Description

H3C SR66 Series Routers User Manual

It is a guide for the user to perform the

operations correctly. It is organized into

the parts of getting started, system

management, interface, link layer

protocol, network protocol, routing

protocol, security, VPN, and QoS.

It also gives the user a detailed

description of the operating commands.

It is organized into the parts of getting

started, system management, interface,

link layer protocol, network protocol,

routing protocol, security, VPN, QoS, as

well as a command index.

Low-End and Mid-Range Series Routers

Cable Manual

This manual introduces all cable pinouts

available with low-end and mid-range

series routers.

Organization

H3C SR6608/6604 Routers Installation Manual is organized as follows:

Chapter Contents

1 Router Overview

Briefly introduces the product

specifications, as well as the features

and applications of the H3C

SR6608/6604 routers.

2 Interface Modules

Describes the interface cards and

interface modules supported by the H3C

SR6608/6604 routers.

3 Arranging Slots and Numbering

Interfaces

Introduces the slots and numbering

rules of the H3C SR6608/6604 routers.

4 Preparing for Installation

Describes the requirements on

installation site, the safety

recommendations before and during

installation, and the required tools.

Chapter Contents

5 Installing the Router

Introduces how to install the

SR6608/6604 routers, as well as how to

connect the power cable, console cable,

AUX port cable, Ethernet cable,

interface card and interface module

cable.

6 Starting and Configuring the Router

Helps you get familiar with the basic

knowledge of how to boot and configure

the H3C SR6608/6604 routers, including

device startup, power-on, and

initialization of system files, and so on.

7 Maintaining Software

Introduces how to maintain the software

of the H3C SR6608/6604 routers,

including upgrading the software and

updating the configuration files.

8 Maintaining Hardware

Introduces how to maintain the

hardware of the H3C SR6608/6604

routers.

9 Troubleshooting

Describes some problems that may

occur during installation and startup of

the router and how to solve them.

Conventions

The manual uses the following conventions:

I. Command conventions

Convention Description

Boldface

The keywords of a command line are in Boldface.

italic

Command arguments are in italic.

[ ]

Items (keywords or arguments) in square brackets [ ] are

optional.

{ x | y | ... }

Alternative items are grouped in braces and separated by

vertical bars. One is selected.

[ x | y | ... ]

Optional alternative items are grouped in square brackets

and separated by vertical bars. One or none is selected.

{ x | y | ... } *

Alternative items are grouped in braces and separated by

vertical bars. A minimum of one or a maximum of all can be

selected.

[ x | y | ... ] *

Optional alternative items are grouped in square brackets

and separated by vertical bars. Many or none can be

selected.

Convention Description

&<1-n>

The argument(s) before the ampersand (&) sign can be

entered 1 to n times.

# A line starting with the # sign is comments.

II. GUI conventions

Convention Description

< >

Button names are inside angle brackets. For example, click

<OK>.

[ ]

Window names, menu items, data table and field names

are inside square brackets. For example, pop up the [New

User] window.

/

Multi-level menus are separated by forward slashes. For

example, [File/Create/Folder].

III. Symbols

Convention Description

Warning

Means reader be extremely careful. Improper operation

may cause bodily injury.

Caution

Means reader be careful. Improper operation may cause

data loss or damage to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements on environmental

protection. For the proper storage, use and disposal of this product, national laws and

regulations must be observed.

H3C SR6608/6604 Routers Installation Manual Table of Contents

i

Table of Contents

Chapter 1 Router Overview..........................................................................................................1-1

1.1 Introduction ........................................................................................................................ 1-1

1.2 Physical Description .......................................................................................................... 1-2

1.2.1 Front View ............................................................................................................... 1-2

1.2.2 Rear View................................................................................................................ 1-4

1.3 System Specifications........................................................................................................ 1-5

1.3.1 RPE-X1 ................................................................................................................... 1-5

1.3.2 FIP-100.................................................................................................................... 1-9

1.3.3 FIP-200.................................................................................................................. 1-13

1.3.4 Dimensions, Weight and LPU Slots ...................................................................... 1-16

1.3.5 Voltage and Current .............................................................................................. 1-16

1.3.6 Interface Modules.................................................................................................. 1-16

1.3.7 Fan Tray ................................................................................................................ 1-19

1.3.8 Operating environment.......................................................................................... 1-19

1.4 Components..................................................................................................................... 1-19

1.4.1 RPE-X1 ................................................................................................................. 1-19

1.4.2 FIP-100/FIP-200.................................................................................................... 1-28

1.4.3 Power Supply Module ........................................................................................... 1-36

1.4.4 Port Lightning Arrester (Optional) ......................................................................... 1-38

1.4.5 Power Lightning Arrester (Optional)...................................................................... 1-38

1.4.6 Signal Lightning Arrester (Optional)...................................................................... 1-39

1.4.7 System Software ................................................................................................... 1-39

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-1

Chapter 1 Router Overview

1.1 Introduction

The H3C SR6608 and SR6604 routers are high-performance service routers

developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter referred to as H3C)

for enterprise networks and carrier-edge access. The SR6608 and SR6604 adopt two

route processing engine-X1s (RPE-X1s), two power modules, and a distributed

modular architecture. Abundant optional modules are available so that the two service

routers can have a powerful processing capability and support flexible configuration to

fully meet the requirements of enterprise networks and carrier networks. The SR6608

and SR6604 can work at the core layer of small- and medium-sized enterprise

networks or at the distribution layer and core layer of large-sized enterprise networks.

They can also work at the access layer of carrier networks or large enterprise networks.

With the high-performance microprocessor technology, advanced hardware

architecture and H3C proprietary Comware V5 platform, the SR6608 and SR6604

provide high service processing capabilities, good service scalability, and high reliability.

In addition, the SR6608 and SR6604 can work together with other H3C network

devices to provide full network solutions for carriers and departments in electric power,

finance, tax, public security, railway and education, as well as for medium- and

large-sized enterprises. The full compliance with national and international standards

ensures the interoperability with the products of other manufacturers at different layers.

The SR6608 and SR6604 support high-speed interface modules (HIMs) and provide a

bus processing capability of up to 10 Gbps, which can meet the high-speed

performance requirements of users. In addition, the SR6608 and SR6604 are

compatible with some multi-functional interface modules (MIMs) of the H3C AR/MSR

series routers to guarantee the smooth upgrade from narrowband access to broadband

access, improve the competitiveness, and protect existing investments. For easy

description, the term “device” is used throughout this document to refer to any SR6608

or SR6604 router if not otherwise specified.

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-2

1.2 Physical Description

1.2.1 Front View

(1)

(2) (3) (4)

(7) (5)(8)(9)(10)

(13)

(6)

(15)

(14)

(12)

(11)

(1) Left mounting bracket (2) Blank panel for RPE-X1 (Slot 1)

(3) RPE-X1 (Slot 0) (4) Right mounting bracket

(5) Chassis handle (6) Fan tray

(7) AC power module (PWR 1)

(8) Blank panel for PoE power module (reserved PoE slot)

(9) Blank panel for power module (PWR 2) (10) ESD socket and silkscreen

(11) Blank panel for LPU (Slot 5) (12) Blank panel for LPU (Slot 4)

(13) Blank panel for LPU (Slot 3) (14) Blank panel for LPU (Slot 2)

(15) Cable management bracket

Figure 1-1 Front view of the SR6608

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-3

(1) (2) (3) (4)

(11)

(13)

(12)

(7) (5)(8)(9)(10) (6)

(1) Left mounting bracket (2) Blank panel for RPE-X1 (Slot 1)

(3) RPE-X1 (Slot 0) (4) Right mounting bracket

(5) Chassis handle (6) Fan tray

(7) AC power module (PWR 1)

(8) Blank panel for PoE power module (reserved PoE slot)

(9) Blank panel for power module (PWR 2) (10) ESD socket and silkscreen

(11) Blank panel for LPU (Slot 3) (12) Blank panel for LPU (Slot 2)

(13) Cable management bracket

Figure 1-2 Front view of the SR6604

 Note:

Currently, the device does not support power over Ethernet (PoE).

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-4

1.2.2 Rear View

(1) Warning label (2) Handle on the rear chassis panel

(3) Upper slide rail for the air filter (4) Air filter (optional)

(5) Lower slide rail for the air filter (6) Chassis handle

(7) Weight-bearing warning label (50 kg, namely, 110.2 lb.)

(8) Grounding screw and sign (9) Vents

Figure 1-3 Rear view of the SR6608

(1) Warning label (2) Handle on the rear chassis panel

(3) Upper slide rail for the air filter (optional) (4) Air filter (optional)

(5) Lower slide rail for the air filter (optional) (6) Chassis handle

(7) Weight-bearing warning label (50 kg, namely, 110.2 lb.)

(8) Grounding screw and sign (9) Vents

Figure 1-4 Rear view of the SR6604

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-5

 Note:

Do not hold the handle indicated by (2) in Figure 1-3 on the rear chassis panel to move

the chassis because it is designed for the convenience of the rear chassis panel

removal, but not for bearing the chassis weight.

1.3 System Specifications

1.3.1 RPE-X1

I. Front view

(1) RESET button (RESET) (2) Run LED (RUN)

(3) Active LED of the RPE-X1 (ACT) (4) Alarm LED (ALM)

(5) Link state/data reception & transmission LED (LINK/ACT)

(6) CF card eject button

(7) CF card slot (8) CF LED (CF)

(9) USB interface 1 LED (USB) (10) Captive screw

(11) Ejector lever (12) USB interface 1 (USB 1)

(13) USB interface 0 (USB 0) (14) AUX port (AUX)

15) Console port (CONSOLE)

(16) Management Ethernet interface (MANAGEMENT) (10/100/1000BASE-T)

Figure 1-5 Front view of RPE-X1

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-6

II. Technical specifications

Table 1-1 Technical specifications for the RPE-X1

Item Specification

Processor

Freescale MPC8548E 1GHz

Processor cores 1

Flash 4 MB

Memory type and size

DDR2 SDRAM

1 GB (default, one memory module)

2 GB (maximum)

NVRAM

128 KB

Console port

1 (9600 bps to 115200 bps, 9600 bps by default)

AUX port

1 (9600 bps to 115200 bps, 9600 bps by default)

Management Ethernet

interface

1 (10Base-T/100Base-TX/1000Base-T)

CF card

 256 MB by default for the built-in CF card

 256 MB, 512 MB, or 1 GB for an optional external

CF card

USB interfaces

2 (USB 0: Type A connector, operating in the host

mode; USB 1: Type B connector, operating in the

device mode)

Reset Button

1

 Note:

 Flash is used for storing the boot file—the BootWare program.

 The memory is used for storing the data exchanged between the system and the

CPU.

 The non-volatile random access memory (NVRAM) is used for storing the exception

information of the system during operation.

 A CF card is used for storing the software system and configuration files of the

device.

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-7

III. LEDs

(1) Run LED (RUN) (2) Active LED of the RPE-X1 (ACT)

(3) Alarm LED (ALM)

(4) Ethernet link state/data reception & transmission LED (LINK/ACT)

(5) CF LED (CF) (6) USB interface 1 LED (USB)

Figure 1-6 LEDs on the RPE-X1

1) Device LEDs

Table 1-2 Description of the device LEDs

LED Status Meaning

Off

No power input is available, or the RPE-X1 has

failed.

Slow blinking

(1 Hz)

The RPE-X1 is operating normally.

RUN (green)

Fast blinking

(8 Hz)

The application software is being loaded (in this

case, never power off the device or hot-swap the

RPE-X1; otherwise the RPE-X1 may be damaged),

or the RPE-X1 is not working.

Off

The RPE-X1 is in the standby state.

ACT (green)

On

The RPE-X1 is in the active state.

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-8

LED Status Meaning

Off

The system is operating normally and there is no

alarm.

On

A fault has occurred to the system. In this state,

you need to check the system log immediately.

ALM (red)

Fast blinking

(8 Hz)

A critical fault has occurred to the system. In this

state, you need to handle the fault immediately.

2) Management Ethernet interface LED

Table 1-3 Description of the management Ethernet interface LED

LED Status Meaning

Solid yellow A 10/100 Mbps link is present.

Solid green

A 1000 Mbps link is present.

Blinking

yellow

Data is being received or transmitted at a rate of

10/100 Mbps.

LINK/ACT

(yellow/green)

Blinking

green

Data is being received or transmitted at a rate of

1000 Mbps.

3) USB 1 LED

Table 1-4 Description of the USB 1 LED

LED Status Meaning

Off

No host is connected to the device-mode USB

interface.

On

A host is connected to the device-mode USB

interface. The USB cable can be unplug in this

state.

USB (green)

Blinking

Data is being transmitted or received through the

device-mode USB interface. In this state, do not

unplug the USB cable.

4) CF LED

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-9

Table 1-5 Description of the CF LED

LED Status Meaning

Off

No CF card is present or the CF card is not

recognizable.

On

A CF card is in position and has been detected.

CF (green)

Blinking

The system is accessing the CF card. In this state,

do not remove the CF card.

 Note:

Do not remove the CF card when the CF LED is blinking. Otherwise, the file system on

the CF card will be damaged.

1.3.2 FIP-100

I. Introduction

Flexible interface platform-100 (FIP-100) is a type of line processing unit (LPU) that

supports H3C legacy multifunctional interface modules (MIMs). FIP-100 can be

inserted in slot 2, 3, 4, or 5 of the SR6608 or slot 2 or 3 of the SR6604. FIP-100 provides

two GigabitEthernet (GE) Combo interfaces and supports four MIMs at the same time.

FIP-100 is hot-swappable.

 Note:

 FIP-100 and FIP-200 are called LPUs in general.

 “Hot-swapping” a module refers to first using the remove slot slot-number [ subslot

subslot-number ] command to stop the module and then pulling it out manually, or

inserting the module into its slot without powering off the device. For details about

the remove slot command, refer to H3C SR66 Series Routers User Manual.

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-10

(1) Slot 1 (2) Slot 2

(3) Slot 3 (4) Slot 4

(5) 10/100/1000 Mbps electrical Ethernet interface 0

(6) 1000 Mbps optical Ethernet interface 0 (7) 1000 Mbps optical Ethernet interface 1

(8) 10/100/1000 Mbps electrical Ethernet interface 1

(9) OPEN BOOK sign

Figure 1-7 Front view of the FIP-100

"OPEN BOOK" sign – Refer to related sections when performing the following

operations:

Operation Reference

Plug/unplug an FIP-100

Section 8.5 “Installing and Removing an

FIP-100/FIP-200” in Chapter 8 “Maintaining

Hardware”

Plug/unplug an HIM/MIM

Section 8. 9 “Installing and Removing an HIM” and

section 8.10 “Installing and Removing an MIM” in

Chapter 8 “Maintaining Hardware”

Connect an Ethernet cable

Section 5.10.3 “Connecting the Management

Ethernet Interface” and section 5.10.4 “Connecting

Ethernet Cables” in Chapter 5 “Installing the

Router”

Plug/unplug an optical module

Section 5.10.5 “Connecting Interface Module

Cables” in Chapter 5 “Installing the Router”

Connect an optical fiber

Section 5.10.5 “Connecting Interface Module

Cables” in Chapter 5 “Installing the Router”

II. Technical specifications

Table 1-6 Technical specifications for FIP-100

Item Specification

Processor

Freescale MPC8548E 1GHz

Processor

cores

1

Flash 4 MB

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-11

Item Specification

Memory type

and size

DDR2 SDRAM

512 MB (default, one 512 MB memory module)

2 GB (maximum)

NVRAM 128 KB

2

10 Mbps, half/full-duplex

100 Mbps, half/full-duplex

Two electrical

interfaces

(automatic

MDI/MDI-X)

1000 Mbps, full-duplex

Combo

interfaces

Two optical

interfaces

1000 Mbps, full-duplex

HIM

Not supported

MIM

Four MIMs supported at the same time

Hardware

encryption

Supported

 Note:

 If you need to install two memory modules, make sure they are of the same type and

size.

 For a Combo interface, the default operating interface is the electrical interface.

 For a Combo interface, you can use either the electrical Ethernet interface or the

optical Ethernet interface. You can use the combo enable { copper | fiber }

command in interface view to switch between the optical and electrical interfaces.

 For details about the combo enable { copper | fiber } command, refer to H3C SR66

Series Routers User Manual.

III. LEDs

FIP-100 provides five LEDs: RUN, SFP1, SFP0, GE0, and GE1. Table 1-7 describes

the LEDs.

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-12

(1) (2)

(5)

(4)

(3)

(1) LED for 10/100/1000 Mbps electrical Ethernet interface 0

(2) LED for 10/100/1000 Mbps electrical Ethernet interface 1

(3) 1000 Mbps optical Ethernet interface LED (SFP0)

(4) 1000 Mbps optical Ethernet interface LED (SFP1)

(5) Run LED (RUN)

Figure 1-8 FIP-100 LEDs

Table 1-7 Description of FIP-100 LEDs

LED Status Meaning

Off

No power input is available or the FIP-100 has

failed.

Slow blinking

(1 Hz)

The FIP100 is working normally.

RUN (green)

Fast blinking (8

Hz)

Application software is being loaded (in this case,

never power off the device or hot-swap the

FIP100; otherwise the FIP100 may be damaged)

or FIP-100 is not working.

Off

No optical link is present.

Solid green

An optical link is present.

Blinking green

Data is being sent or received at a rate of 1000

Mbps.

SFP0 to

SFP1

(yellow/gree

n)

Solid yellow

The optical transceiver failed to be detected.

Off

No link is present.

Solid green

A 1000 Mbps link is present.

Blinking green

Data is being received or transmitted at a rate of

1000 Mbps.

Solid yellow

A 10/100 Mbps link is present.

GE0 to GE1

(yellow/gree

n)

Blinking yellow

Data is being received or transmitted at a rate of

10/100 Mbps.

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-13

IV. Slots

FIP-100 provides four MIM slots for some H3C legacy MIMs.

The MIM slots on FIP-100 are numbered 1 to 4 from the bottom up and from right to left,

as shown in

Figure 1-9.

(1) Interface module slot 1 (2) Interface module slot 2

(3) Interface module slot 3 (4) Interface module slot 4

Figure 1-9 Interface module slots on FIP-100

 Note:

The numbers 1 through 4 in Figure 1-9 represent Slot 1 through Slot 4 respectively.

Actually, these numbers are not silk-screened on an FIP-100.

1.3.3 FIP-200

I. Introduction

Flexible interface platform-200 (FIP-200), another type LPU of the device, provides a

high-speed service processing capability. FIP-200 supports SR66 series HIMs and

some H3C legacy MIMs and provides two Combo interfaces. In consideration of the

smooth upgrade requirements, FIP-200 supports two HIMs or two MIMs, or intermixing

of an HIM and an MIM. FIP-200 is hot-swappable.

(1) Slot 1

(2) Slot 2

(3) 10/100/1000 Mbps electrical Ethernet interface 0

(4) 1000 Mbps optical Ethernet interface 0

(5) 1000 Mbps optical Ethernet interface 1

(6) 10/100/1000 Mbps electrical Ethernet interface 1

(7) OPEN BOOK sign

Figure 1-10 Front view of FIP-200

H3C SR6608/6604 Routers Installation Manual Chapter 1 Router Overview

1-14

 Note:

"OPEN BOOK" sign – Refer to related sections when performing the following

operations on FIP-200:

 Plugging/unplugging an FIP-200

 Plugging/unplugging an HIM/MIM

 Connecting an Ethernet cable

 Plugging/unplugging an optical module

 Connecting an optical fiber

II. Technical specifications

Table 1-8 Technical specifications for FIP-200

Item Specifications

Processor

Multi-core MIPS CPU, 1 GHz

Processor cores 8

Flash 4 MB

Memory type and

size

DDR2 SDRAM

 1 GB (default, two 512 MB memory modules)

 2 GB (maximum)

 1.5 GB not supported

NVRAM 128 KB

2

10 Mbps, half/full-duplex

100 Mbps, half/full-duplex

Two electrical

interfaces (automatic

MDI/MDI-X)

1000 Mbps, full-duplex

Combo interfaces

Two optical

interfaces

1000 Mbps, full-duplex

HIMs

2

MIMs

2

Hardware

encryption

Supported

Page is loading ...

H3C SR6604 Installation guide

This manual is also suitable for

H3C SR6604 Installation guide

Related papers

Other documents