2. PortaPivot
  3. V2-NL
V2-NL

PortaPivot V2-NL Installation guide

  • Hello! I've reviewed the Stealthpivot NL Quickstart Guide and I'm ready to assist you with any questions you may have. This guide includes details on installation, adjustments and also describes features such as interchangeable gas dampers and different positioning options. Feel free to ask!
  • What is the minimum joint dimension?
    What is the maximum door weight?
    What gas dampers are used?
By PortaPivot
8 x Maxxfast CST 4.5x50
8 x DIN ≈965 A-M5x10
STEALTHPIVOT NL - QUICKSTART GUIDE
www.portapivot.com
4 x SP-CRL
2 x SP-PHE (=NL)
1 x TORX BIT TX 25
1 x TORX BIT TX 20
16 x DIN 988-5x10x1
4 x DIN916-M6x6
4 x Fisher
Duopower 8x40
4 x Maxxfast
CK 6x50
4 x PAP-ADKPB 2 x SP-PZOV 3 mm
2 x SP-PZOV 1.5 mm
2 x SP-PZOV 1 mm
1 x PAP-1W
8 x Maxxfast CST 4.5x50
4 x Fisher Duopower 8x40
1 x SP-PS&KAL
2 x PAP-2W
2 x magnet South/North
4 x ISO 10642 - M4x8
OPTIONAL STEALTHPIVOT NL ACCESSORY SET
OPTIONAL STEALTHPIVOT INSTALLATION TOOL
STEALTHPIVOT NL SET
33
25.25
18
99
172
127
33
7.25
172.5
138.5
25.75
35
25.75
R5.25
Ø3
R5
35
158
11.25
STEALTHPIVOT NL CAVITY DIMENSIONS (mm)
STEALTHPIVOT NL DIMENSIONS (mm)
1000
500
250
85
joint A & BX
Th
2
2
3
4
40
2
2
3
3
30
2
3
3
5
50
3
3
4
7
60
11 mm
3 mm* 3 mm*
11 mm
Xmax = 1/2
Xmin = 85
joint A joint B
Pivot distance = X
Door thickness = Th
WIDTH = 0-1250
Top & bottom joints: min. 11 mm
*Left & right joints:
The minimum joint depends on the
door thickness and pivot distance.
For visual coherence, we advise to
use equal joints left and right. See
visual and table below for advised
left and right joint dimensions.
Max. width = 1250 mm
Max. weight = 75 kg (165 lbs)
Axis position (X) = 85 mm up to 1/2
AXIS POSITIONS (X)
ADVISED JOINT DIMENSIONS
min 85 mmup to 1/2
up to 1/2 min 178 mm
180°
360°
INTEGRATION OPTIONS
S90 - 90° STOP ACCESSORY
75 mm
AXIS*
75 mm
Ø 8 mm
45 mm deep
1
3
2
DRILL PIVOT MOUNT HOLES
*Depends on doorway measurements!
SYNCHRONIZE PIVOT AXIS HEIGHT IN DOORWAY
difference
difference
Height between floor and
ceiling at pivot axis
Pivot to pivot
distance on door
DOORWAY DOOR
MAXIMUM
RECTANGLE
Compare the measured doorway height at the pivot axis with the
pivot to pivot distance of the door. Synchronize them if necessary by
using one of the hinge height adjustment options on the next page.
INSTALL IN SOLID OR REINFORCED MATERIALS!
For TOP or BOTTOM joint adjustment
= preferred method for bottom hinge
1. Shims between hinge and door
For TOP or BOTTOM joint adjustment
= faster but less stable method
2. Shims between hinge and floor/ceiling
Only for TOP joint adjustment and non compressible door structures!
3. Inbus screws
HINGE HEIGHT ADJUSTMENT OPTIONS
1
3
2
Use the drill tool to rotate the pivot mount in place.
Repeat for the bottom pivot mount.
Install the octagonal inserts at ‘position 1’ in the top mount, then insert
screws but do not fully tighten yet. Repeat for the bottom mount.
Always rotate the pivot mount in
the closing direction of the door! If
not, the door will be blocked in its
opened position.
INSTALL ASSEMBLED DOOR
Place the assembled door in the
doorway, with the pivot axis in
between the 2 pivot mounting holes.
Tilt the door upright
and keep it in place.
Put both pivots in their ‘closed’ position.
1
3
2
4
5
1,35 mm
1,50 mm
1,20 mm
1,05 mm
The inserts are excentric, so each position will affect the
centerline angle of the door leaf.
The view below shows the effect on the centerline angle
when rotating the inserts to different positions.
ADJUST PIVOT AXIS POSITION
0° POSITIONING ADJUSTMENTS
Optional
MINIMIZE VISIBLE COMPONENTS
INTERCHANGEABLE GAS DAMPERS
Slide the 3D printed covers over the base of the
hinge to cover up the screws and hexagonal inserts.
Stealthpivot NL and XL are equipped with 480N gas dampers which
can easily be replaced.
Optional 750N dampers are also available.
0°
+90°
-90°
0°
+90°
50
11
11
Ø8
neodymium
magnet
2-way
magnet holder
neodymium
magnet
1-way
magnet holder
69
55
11
optional shim for height adjustment
2-way magnet holder
1-way magnet holder
2-way magnet holder
Ø8 mm
Maxxfast CST 4.5x50
Fischer duopower 8x40
OPTIONAL 0° POSITIONING ACCESSORIES
0° positioning magnet
(North/south)
0° positioning magnet
(North/south)
www.portapivot.com
1-WAY2-WAY
1-WAY
magnet holder
2-WAY
magnet holder
2-WAY SETUP 1-WAY SETUP
By PortaPivot
Find more pictures, information and in-depth manuals
@
WWW.PORTAPIVOT.COM
/