Version
V1.4 0922
Everything you need
for your Gs on Glss
Cooktop is in this
User Mnul
Model/s
ECGG604W
ECGG905W
User Manual
2
Welcome
Congrtultions on purchsing your new Gs Cooktop. The Estto brnd is
proudly distributed within Austrli by Residenti Group Pty Ltd.
Plese refer to the wrrnty crd t the rer of this mnul for informtion
regrding your product’s prts nd lbour wrrnty, or visit us online t:
www.residenti.group
At Residenti Group, we re customer obsessed nd our Support Tem re
there to ensure you get the most out of your pplince. Should you wnt to
lern more bout your new gs cooktop, it's fetures or importntly tking
cre of the pplince, our Support Tem re here to help.
You cn use our online Support Centre t nytime by visiting:
http://support.residentigroup.com.u
Or you cn contct us vi phone by diling: 1300 11 HELP (4357).
It is importnt tht you red through the following use nd cre mnul
thoroughly to fmilirise yourself with the instlltion nd opertion
requirements of your pplince to ensure optimum performnce.
Agin, thnk you for choosing n Estto pplince nd we look forwrd
to being of service to you.
Kind Regrds,
The Residenti Tem
Residenti roup
—
Head Office
165 Brkly Avenue
Burnley, Victori
Austrli 3121
—
ACN
600 546 656
—
Online
residenti.group
www.estto.house
@estto.house
—
Postage
PO Box 5177
Burnley, Victori
Austrli 3121
—
Telephone
1300 11 4357
www.esatto.house
esatto.house
3
Page 2
Welcome
Page 4
Safety Instructions
Page 6
Product Overview
Page 8
Before First Use
Pge 9
Using Your
Cooktop
Pge 10
Burners
Page 11
Cleaning Care
Page 12
Troubleshooting
Pge 13
Technicl Dt
Pge 14
Instlltion
Instructions
Pge 16
Gs Connection
Pge 19
LPG Conversion
Page 20
Electrical
Connection
Page 21
Testing Appliance
Operation
Pge 23
Purchse Detils
Pge 24
Wrrnty
Contents
User Manual
4
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP
FOR FUTURE REFERENCE
Read this manual thoroughly before rst use,
even if you are familiar with this type of product.
The safety precautions enclosed herein reduce
the risk of re, electric shock and injury when
correctly adhered to. Make sure you understand
all instructions and warnings.
Keep the user manual in a safe place for future
reference, along with the completed warranty
card and purchase receipt. If you sell or transfer
ownership of this product, pass on these
instructions to the new owner.
Always follow basic safety precautions and
accident prevention measures when using an
electrical appliance. The following statements you
will see in this booklet have these meanings:
WARNING: Indicating information concerning
your personal safety.
CAUTION: Indicating information on how
to avoid damaging the appliance, benchtop
or cabinetry.
IMPORTANT: Indicating tips and information
about use of the appliance.
USAGE CONDITIONS AND RESTRICTIONS
• Domestic use only: This appliance is intended
for indoor household use only. It is not intended
for commercial, industrial or outdoor use. It is
not intended for use in a recreational vehicle.
• Purpose: Do not use this appliance for anything
other than its intended purpose. Other uses are
not recommended and may cause re, electric
shock or personal injury.
• Attachments: The use of attachments is not
recommended by the appliance manufacturer
and distributor as they may be hazardous.
• Improper use: Damage due to improper use,
or repairs made by unqualied personnel will
void your warranty. We assume no liability
for any eventual damages caused by misuse
of the product or noncompliance with these
instructions.
BEFORE USING YOUR APPLIANCE
This manual explains the proper use of your new
Esatto cooktop. Please read this manual carefully
before using the product. This manual should
be kept in a safe place for handy reference. This
rangehood is a domestic appliance which has been
manufactured and tested to comply with Australian
and New Zealand Standard AS/NZS 5263.
This cooktop must only be installed in accordance
with the instructions provided. Incorrect
installation may cause harm to persons, damage
property and void the product’s warranty.
Read the following carefully to avoid damage
or injury.
IMPORTANT: Check for any damage or marks.
If you nd the appliance is damaged or marked,
you must report it within 7 days if you wish to
claim for damage/ marks under the manufacturer’s
warranty. This does not aect your statutory rights.
Sfety Instructions
esatto.house
5
WARNING: Follow these instructions carefully
to avoid injury or damage to your appliance.
• Do not allow pots to boil dry, as damage to both
pan and cooktop may result.
• Do not operate the cooktop for an extended
period without a pot or pan on the burner.
• Do not allow large cookware to overhang the
cooktop onto adjacent benchtop. This will cause
scorching to the benchtop surface.
• Do not allow cooking pots or pans to intrude into
the area which is close to the controls.
• Ensure burner bodies and trivets are properly
located on the cooktop (i.e. correctly assembled
and positioned).
CAUTION: Follow these instructions carefully
to avoid an electric shock or re.
It is important to use your cooktop safely. Check
these safety points before using your cooktop.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
• Children should be supervised to ensure they do
not play with this appliance.
• During use, this appliance becomes hot. Care
should be taken to avoid touching hot surfaces.
To avoid burns, young children should be kept
awa y.
• This appliance must not be used as a
space heater.
• Keep vents clear of obstructions.
• In order to avoid a re, this appliance must be
kept clean.
• Do not spray aerosols in the vicinity of this
appliance while it is in operation.
• Do not store ammable materials on or under
this appliance, e.g. aerosols.
• Do not remove the trivet and enclose the burner
with a wok stand as this will concentrate and
deect heat onto the burner.
• Do not use large pots or heavy weights
which can bend the trivet or deect ame onto
the burner.
• Do not place anything, e.g. asbestos mat
between pan and trivet as serious damage to the
cooktop may occur.
• For maximum stability, ensure pots and pans are
centrally located on the trivets.
• Handles should be turned away from the front of
the bench to avoid accidents.
• Do not modify this appliance.
• Only models tted with ame safeguard
can be used in marine craft, caravans
or mobile homes.
UNPACKING
During transportation, protective packaging was
used to protect the appliance against any damage.
After unpacking, please dispose of all elements of
packaging in a way that will not cause damage to
the environment.
All materials used for packaging the appliance are
environmentally friendly; they are 100% recyclable
and are marked with the appropriate symbol.
CAUTION: During unpacking, the packaging
materials (polythene bags, polystyrene pieces, etc.)
should be kept out of reach of children.
DISPOSAL OF THE APPLIANCE
Old appliances should not simply be disposed
of with normal household waste and should be
delivered to a collection and recycling centre for
electric and electronic equipment. A symbol shown
on the product, the instruction manual or the
packaging shows that it is suitable for recycling.
Materials used inside the appliance are recyclable
and are labelled with information concerning this.
By recycling materials or other parts from used
devices you are making a signicant contribution
to the protection of our environment.
Information on appropriate disposal centres
for used devices can be provided by your local
authority.
User Manual
6
Product Overview
YOUR COOKTOP
Figure 1A — ECGG604W
Figure 1B — ECGG905W
KEY
A. Toughened Blck Glss
B. Burner Control Knobs
C. Cst Iron Trivets
D. Auxiliry Burner
E. Semi Rpid Burner
F. Rpid Burner
G. Wok Burner
A
B
E
E
C
D
G
AC
ED
E F
G
B
esatto.house
7
THE BURNER
Figure 2A
COOKTOP COMPONENTS ACCESSORIES
Your Estto cooktop is supplied with:
1 × Cooktop
1 × Wok support trivet
1 × Voltge regultor vlve
4 × Injector (ECGG604W)
5 × Injector (ECGG905W)
1 × Pressure joint
4 × Brckets
4 × Sponges
4 × Screws
1 × Elbow
1 × User Mnul
1 × Quick Strt Guide
Figure 2B
Burner Flame Ports
Ignition Spark Plug
Flame Safeguard Sensor
Skirt
Burner
Injector
Note: The images in this user manual are for reference only. Your appliance may appear dierently.
User Manual
8
INSTALLATION
• An uthorised person must instll this pplince
nd MUST provide Certicte of Complince.
This certicte should be retined long with
purchse informtion.
• Before using the cooktop, ensure tht ll
pcking mterils re removed from the
pplince.
• In order to void ny potentil hzrd, the
instlltion instructions in this booklet, nd ny
lbels on the pplince must be followed.
• Ensure tht ll specied vents, openings nd ir
spces re not blocked.
• Where the pplince is built into benchtop,
the benchtop mteril must be cpble of
withstnding 85°C.
• Ensure tht the duplicte rting lbel
(in the instruction pck) is ttched to
redily ccessible djcent surfce, so tht the
cooktop cn be esily identied in the cse of
service cll.
SERVICING
• Servicing MUST only be crried out by
uthorised personnel.
• To mintin sfe opertion, it is recommended
tht the product be inspected every ve yers
by n uthorised service person.
• If the supply cord is dmged, it must be
replced by the mnufcturer, its service gent
or similrly qulied persons in order to void
hzrd.
WARNING: Never instll cooktop tht hs
been dmged. Plese contct our Service Tem
for ssistnce.
CLEANING
• Alwys ensure the pplince is turned o
before clening.
• This pplince contins luminium ttings.
Do not use custic bsed cleners.
• Do not use stem cleners s this my cuse
moisture build up on electricl components.
• Alwys clen the pplince immeditely fter
ny food spillge.
• Do not plce ny components in dishwsher.
• Refer to the Clening Cre section on pge 11
of this user mnul for instructions on clening
nd mintining your glss hob pnel.
CAUTION: Never plce burners or trivets in
dishwsher.
Before First Use
esatto.house
9
STANDARD BURNER
Figure 3A
TRIPLE RING WOK BURNER
Figure 3B: ECGG604W Figure 3C: ECGG905W
Both rings of the wok burner operte between
knob rottion settings ‘1’ nd ‘9’.
NOTE: Gs controls turn nticlockwise from ‘OFF’
nd hve limited movement.
CONTROLS
Ech burner is controlled by control knob.
The mrkings on the control pnel indicte which
burner the knob controls, nd the setting for tht
burner (See Figure 3).
LIGHTING BURNERS
Electronic ignition: These cooktops re tted with
mins powered ignition. When the pplince hs
been connected nd the power is on, depressing
ny knob will relese sprks to ll burners.
CAUTION:
• Keep hnds cler of burners when lighting.
• If burner does not light within 5 seconds, turn
knob to ‘OFF’ position, wit to llow gs to
disperse nd then try lighting gin.
• Burners MUST be operted between ‘1’ nd ‘9’
settings only.
To light burner, the knob must be turned to the
position, then pushed down s fr s possible
for pproximtely 5 seconds. If the me goes
out when the knob is relesed simply depress the
knob gin, this time holding it down with slightly
more force for the sme length of time.
The height of the me cn be vried by turning
the control knob towrd the ‘1’ position.
NOTE: When the wok burner is turned to setting 1,
only the smll inner ring stys lit. This is norml
function of the dul wok burner to provide very
low power me option.
In the bsence of electricl power, crry out the
ignition directly to the burner with hnd held
ignition source.
Using Your Cooktop
Note: The diagrams in this user manual are for reference only. Your appliance may appear dierently.
User Manual
10
Burners
CHOICE OF BURNER
For your convenience there is choice of burners
to choose from:
• A smll Auxiliry burner for specil low het
nd slow cooking. Minimum pn size 120mm
(Mximum 160mm).
• A medium Semi-Rpid burner for norml
cooking nd simmering. Minimum pn size
160mm (Mximum 180mm).
• A lrge Rpid burner (ECGG905W only) for fst
heting nd lrge pots nd pns. Minimum pn
size 200mm (Mximum 240mm).
• A Triple Ring wok burner for very fst heting
using wok or lrge pot or pn. Minimum pn
size 200mm (Mximum 240mm).
To conserve gs plce the pn centrlly over the
burner nd djust the me so tht it does not
extend pst the edge of the pn (Figure 4). Do not
boil food too rpidly. A vigorous boil will not cook
food ny fster, nd will wste energy.
Figure 4
POTS AND PANS
All common pots nd pns; luminium,
stinless steel, cst iron, cermic, etc., my
be used on your new gs cooktop. Ensure tht
the pots or pns re stedy nd hve t bses
to void dngerous spill-over of hot liquids nd
wsted energy.
CAUTION:
Never use sbestos mts, wire mts or grids,
or luminium foil s it cn led to overheting,
crcked enmel or broken glss. The wrrnty will
be void if these items re used nd cuse filure.
Woks should only be used on the wok burner nd
the wok support trivet. Refer to Figure 1A 1B on
pge 6 depending on your model.
INCORRECT
A me tht is too high will
cuse gs wstge long
with possibility of heting
or dmge to your hndles.
CORRECT
For lrge burner,
use lrge utensil.
CORRECT
A correct me height will
sve gs usge.
CORRECT
For smll burner,
use smll utensil.
esatto.house
11
Clening Cre
CAUTION:
Ensure the pplince is o nd cool before
clening.
TRIVETS
Persistent stins my require rubbing with
nylon scourer or cremed powder clensers.
Household enmel cleners re vilble, follow
the mnufcturer’s instructions in their use.
Hrsh brsive cleners, powder cleners,
steel wool or wx polishes should not be used.
GLASS HOB
The glss used s the primry hob hs been
toughened nd mnufctured to the highest
possible stndrds for both sfety nd relibility.
However, it must be remembered tht s it is
glss, it my brek. Tret it ccordingly. To clen
the glss hob use soft cloth or sponge with
detergent nd wrm wter.
CAUTION: Try to clen up nd remove spillges
immeditely, while the hob is still hot! Especilly
sugr nd foods with high sugr content
(eg. jm), melted plstics nd foil, ll of which cn
dmge the hob if left.
WARNING! If the surfce is crcked, switch o
the pplince immeditely to void the possibility
of electric shock.
If the hob requires extensive clening:
1. Remove soilge using the rzor blde scrper.
Angle the scrper t pprox. 45° nd scrpe
wy the spillge. The rzor blde cn be
pressed down hrd onto the hob without
cusing ny dmge.
2. Use hob clener product fter there hs been
sucient time llowed for the hob to cool.
Shke the bottle nd pply smll quntity of
clener directly onto the hob.
Rub clen using dmp cloth or pper towels.
3. Use dmp cloth to remove ll remining
trces of the clener, which could otherwise
burn on when the hob is next used. Wipe the
hob dry.
TRIVETS AND BURNERS
These cn ll be lifted o nd removed for
seprte clening.
CAUTION: When retting the burners, ensure
tht they re correctly seted.
Ensure burners re thoroughly dried fter clening
or spillge. When clening the burners, ensure
tht ll the me ports re free of ny blockge
(refer to Figure 2B on pge 7). If necessry, use
toothpick or brush to cler ports. The outer
surfce of the burner cps hve polished
nish nd extr cre needs to be tken to void
scrtching this surfce during clening. In
instnces of hevy soiling, it my be necessry to
pply non-brsive clening compound nd rub
with cloth until the soiling is removed nd then
nish with soft, dry cloth.
WARNING:
NEVER plce trivets or burners in the dishwsher.
IGNITION SPARK PLUG
FLAME SAFEGUARD SENSOR
Gently clen the ignition sprk plug nd me
sfegurd sensor with dmp cloth to void
lighting diculties. Ensure tht they re dry
before use.
INJECTOR
Ensure the injector remins free of ny foreign
mteril. If necessry, use thin piece of wire to
cler the orice.
User Manual
12
Troubleshooting
If you hve problem with the cooktop, check the tble below. You my be ble to solve the problem
nd this will sve you from pying for service cll. You will hve to py for service cll even in the
wrrnty period if the problem is one listed below.
Tble 1
PROBLEM POSSIBLE CAUSE SOLUTION
Burner will not light
even though the
sparker is working
Knob not held down long enough in ‘9’
position for ame safeguard.
Repeat lighting procedure and
hold knob down for 5 seconds in
‘9’ position. (Refer page 9).
Gas supply valve turned o. Turn on gas supply to appliance.
Wrong knob turned.
Ensure the knob you are turning
corresponds to the burner you
want to light.
Port blockage in ignition area. Ensure that ports in ignition area
are clean and dry.
Ignition spark plugs wet or dirty. Dry or clean ignition spark plugs.
No spark is obtained
when control knob is
activated
Electricity supply is disconnected or
switched o.
Switch on electricity or check
fuses.
Ignition spark plugs wet or dirty. Dry or clean ignition spark plugs.
Flames uneven or
tending to lift
Flame ports blocked or wet. Clean or dry ame ports.
Burner cap incorrectly tted. Ensure this component is
tted correctly.
Flames not staying on
when knob
is released
Knob not held down long enough in ‘9’
position for ame safeguard to engage.
Repeat lighting procedure and
hold knob down for 5 seconds in
‘9’ position. (Refer page 9).
Knob not set between ‘1’ and ‘9’ Knob MUST be set between
these positions.
Dirt or spillage on ame safeguard
sensor. Clean ame safeguard sensor tip.
Low heat, slow
cooking
Incorrect cooking pot or pan being
used. Refer to Figure 4 (page 10).
Benchtop or knobs
overheating
Incorrect cooking pot or pan being
used. Refer to Figure 4 (page 10).
Pot or pan not located on burner
properly.
Ensure pot or pan is centrally
located on burner.
esatto.house
13
Technicl Dt
Estto reserves the right to lter these specictions. This pplince conforms to AS/NZS 5263.
Tble 2
FEATURES ECGG604W ECGG905W
Burners 4 5
Wok Yes, triple ring Wok Yes, triple ring Wok
Ignition 220–240V~ 220–240V~
Trivet Cast Iron Cast Iron
Hob Material Toughened Glass Toughened Glass
Features Ignition under knob Ignition under knob
Flame Failure Safety Yes Yes
Colours Black Glass Black Glass
Gas Types NG (LP conversion
kit supplied)
NG (LP conversion
kit supplied)
COOKTOP PHYSICAL DIMENSIONS mm
Width 600 900
Depth 510 510
Height 100 100
CUT OUT DIMENSIONS mm
Width 560 830
Depth 490 490
ENERGY RATING NG MJ/h
Auxiliary burner 4.3 4.3
Semi Rapid burner × 2 6.3 6.3
Rapid burner N /A 10.8
Wok burner 13.5 13.5
Total MJ/h 30.4 41.2
User Manual
14
Instlltion Instructions
This pplince must be instlled by n uthorised person nd in complince with:
• AS/NZS 5601.1 Gs Instlltions Prt 1: Generl Instlltions, nd AS/NZS 5601.2 Gs Instlltions
Prt 2: LP Gs instlltions in crvns nd bots for non-propulsive purposes, or the relevnt
instlltion code for gs pplinces in your country.
• The locl gs tting regultions, municipl building codes, electricl wiring regultions nd ny other
relevnt sttutory regultions.
• The prticulr instructions s given below.
• A certicte of complince MUST be given to the customer fter the ppliction is successfully
instlled.
CAUTION: Cooktops re supplied set up for nturl gs (NG). To use on LPG, the injectors must be
chnged using the conversion kit supplied. Refer LPG Conversion on pge 19.
Figure 5A – ECGG604W Figure 5B – ECGG905W
* Minimum clernce from cut-out to combustible surfce.
NOTE: This dimension is not relevnt if the djcent surfce is non-combustible.
600
510
490
100
560
Gas Supply
Connection
120*
145*
90
*
900
510
490
100
Gas Supply
Connection
130*
110*
130*
830
esatto.house
15
INSTALLATION PROCEDURE
• The bench cutout should be mde s per
cutout dimensions in Tble 2 nd Figure 5A
5B (depending on your model).
• Adjcent wlls, cupbords nd protection
for combustible mterils: Ensure tht the
pplince is instlled in ccordnce with
AS/NZS 5601.1, or AS/NZS 5601.2 with regrd
to clernces to combustible surfces nd
mterils, nd clernces to rngehoods nd
exhust fns.
To ensure clernces to combustible
surfces observe the minimum distnce
requirements shown in Figure 5A 5B
(relevnt to your model).
Clernces to combustible surfces my be
reduced if combustible surfces re protected
in ccordnce with AS/NZS 5601.1, or
AS/NZS 5601.2.
• Brrier: A brrier must be instlled to prevent
ccidentl contct with the cooktop bse,
where the bse of the cooktop is ccessible
from below (i.e. Inside cupbord, etc.).
A minimum clernce of 25mm must be
mintined between the bse nd the brrier.
This brrier my be mde of ny non-
combustible, rigid mteril.
Brrier protection is not necessry if the
product is instlled bove n underbench oven
or similr pplince nd/or if the cupbord
construction is such tht the underside of the
cooktop is not ccessible.
• Ensure tht there is n erthed power outlet
within 900mm of the rer right hnd side of
the cooktop when instlled. This should be
ccessible t ll times.
• A self-dhesive Fom Tpe hs been provided
to ct s seling gent nd is to be plced
round the edge of the hob underside. Ensure
tht there re no gps in the Fom Tpe. Tke
cre to ensure tht the sels meet without
overlpping. The thickness of this Fom Tpe is
3mm nd the width is 10mm.
WARNING: Do not use silicon selnt to
sel the pplince ginst the benchtop. This
will mke it dicult to remove the pplince
should the cooktop need service.
• Fit the pull down clmps supplied to
ensure tht the cooktop cnnot move fter
instlltion. Refer to Figure 6 nd the following
instructions.
• Remove ny excess sel visible fter
instlltion
WARNING: Filure to x the cooktop to the bench
could result in loosening of the gs connection
through movement of the cooktop nd gs lek
my result.
Clmps nd screws re supplied with ech
cooktop. Fit the clmps s shown in Figure 6.
When benchtops re less thn 35mm in thickness,
it my be necessry to t spcer between the
benchtop nd ech clmp to ensure clmps cn
be tightened suciently.
FITTING THE CLAMPS
• Ensure tht the hob is free from ll burner
pieces nd trivets. Plce the hob upside down
on soft surfce to protect both the hob nd
your worksurfce from dmge.
• Plce the brcket (B) over the holes tht mtch
the size of the screws. There re one set of
screw holes in ech corner of the hob. Slightly
tighten screw (C) through the brcket (B) so
tht the brcket is ttched to the hob whilst
still llowing you to djust it’s position.
• Crefully turn the hob bck over nd then
gently lower it into the perture hole tht you
hve cut-out in your benchtop.
• On the underside of the hob, djust the
brckets into position tht is suitble for your
benchtop. Then fully tighten the screws (C) to
secure the hob into position.
Figure 6
Installing the appliance
Sponge
Bottom view
The thickness of the sponge is 3 mm.
The width of the sponge is 10 mm.
of the screws.There are one set of screw holes in each
corner of the hob (H) .
Slightly tighten a screw (C) through the bracket (B) so
that the bracket is attached to the hob, but so that you
can still adjust the position
.
.2 Carefully turn the hob back over and then gently lower
it into the aperture hole that you have cut out.
.3 On the underneath of the hob, adjust the brackets into
a position that is suitable for your worktop.
Then fully tighten the screws (C) to secure the hob into
position.
(A) SEALING STRIP
(C) SCREW (B) BRACKET
17
Remove the pan supports, the burner lid
and flame spreader and carefully turn the
appliance upside down and place it on a
cushioned mat.
Take care that the Ignition devices and
flame supervision devices are not damaged
in this operation.
2. Apply the sponge provided around the
edge of the appliance.
3.
1.
Do not leave a gap in the sealing agent or
overlap the thickness.
3ODFHWKHEUDFNHW %RYHUWKHKROHVWKDWPDWFKWKHVL]H
7KLVZLOOPDNHLWGLI¿FXOWWRUHPRYHWKH
DSSOLDQFHIURPWKHDSHUWXUHLQIXWXUH
SDUWLFXODUO\LILWQHHGVWREHVHUYLFHG
Do not use a silicon sealant to seal the
appliance against the aperture.
(A) SEALING STRIP
(B) CLAMP
(C) SCREW
User Manual
16
Gs Connection
OPERATION ON N.G./S.N.G
This appliance is supplied for use with Natural
Gas. However, it can be converted for use with
LPG. Refer to LPG Conversion on page 19.
SUPPLY PIPE SIZING
The total hourly gas consumption for the
appliance is shown on the data label. The required
supply pressure (i.e. at inlet to appliance regulator)
for each gas type is shown on the data label, and
given in Table 3 (page 18). Use this information
in conjunction with the length of run, number
of elbows, tees and bends, the available service
pressure and the supply requirements of other
installed appliances to determine a suitable
pipe size.
For assistance in this matter refer to the
appropriate section of AS/NZS 5601.1 or
AS/NZS 5601.2.
An AGA certied class B or D exible connection
may be used to connect the cooktop in
accordance with AS/NZS 5601.1, in particular
section 5.9 and clause 6.10.1.8, or AS/NZS 5601.2,
in particular section 2.11.
Where a hose assembly is used and the cooktop
is in the installed position, the hose assembly shall
be suitable for connection to a xed consumer
piping outlet located at a point 800 – 850mm
above the oor and in the region outside the width
of the appliance to a distance of 250mm. The
point of connection to consumer piping must be
accessible with appliance installed.
ELBOW POSITIONING
It is possible to reposition the elbow if required
by loosening the locking nut and elbow by using
two spanners. Re-tighten the entire assembly after
the elbow has been repositioned. When tting
elbow to appliance, ensure that the sealing washer
is tted.
Note to Installer: Assembly of elbow to manifold
at rear of unit requires two spanners to secure
locking nut and ensure leak free connection.
For this reason the elbow is best secured onto
cooktop manifold before installing unit into
benchtop.
esatto.house
17
Gas Connection
Statutory requirements
This installation must conform with the following:
■Manufacturer’s Installation instructions
■Local Gas Fitting Regulations
■Municipal Building Codes
■Refer to AS/NZS 5601.1 for Gas Installations
■S.A.A. Wiring Code
■Local Electrical Regulations
■Any other statutory regulations
Preparing to install
Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to
be inserted in a benchtop cutout. Only an officially authorised technician should
connect the appliance. Before you begin, turn off the gas and electricity supply.
19
A full operational test and a test for possible leakages must be
carried out by the fitter after installation.
Access to the whole length of the connection hose must be possible
and the gas hose must be replaced before its use before the end of
service life (indicated on the hose.)
Before Leaving-Check all connections for gas leaks with soap and
water.
DO NOT use a naked flame for detecting leaks. Ignite all burners both
individually and concurrently to ensure correct operation of gas
valves, burners and ignition. Turn gas taps to low flame position and
observe stability of the flame for each burner individually and all
together. Adhere the duplicate data plate to an accessible location
near the hotplate. When satisfied with the hotplate, please instruct
the user on the correct method of operation. In case the appliance
fails to operate correctly after all checks have been carried out, refer
to the auth orised service provider in your area.
Natural gas connection
95
115
LPG gas connection
pressure test point
pressure test point
Figure 7
REGULATOR
An appliance regulator is provided. The regulator
must be positioned so that the pressure test nipple
is accessible when the appliance is installed.
Connect the gas supply to the ½” B.S.P. internal
thread inlet of the regulator. Refer to ‘bench
cutout’ Figure 5A 5B (relevant to your model) for
connection point position. Regulators are supplied
pre-adjusted and congured by the component
maker for use with Natural Gas.
The appliance installer is not required to
make an adjustment to obtain the correct outlet
pressure setting.
An arrow on the base of the regulator indicates the
direction of gas ow when the inlet and outlet of
the regulator is orientated correctly.
When the regulator has been tted check for leaks
from the connections with soapy water.
ASSEMBLY OF THE REGULATOR
The assembly of the regulator to the cooktop
manifold is achieved via the elbow union and
sealing washer supplied, refer to Figure 7.
The ½” parallel thread connects to the manifold,
and the sealing washer is placed between the
manifold end and the at face on the elbow.
The ½” tapered thread connects to the outlet of
the regulator, and is sealed on the thread using
approved thread sealing tape or approved thread
sealing compound.
The inlet of the regulator is a ½” parallel thread
and is connected to consumer piping or hose
assembly.
Regulators are supplied pre-adjusted and
congured by the component maker for use with
Natural Gas.
The appliance installer is not required to make an
adjustment to obtain the correct outlet
pressure setting.
An arrow on the base of the regulator indicates
the direction of gas ow when the inlet and outlet
of the regulator is orientated correctly. When the
regulator has been tted check for leaks from the
connections with soapy water.
User Manual
18
CHECKING THE GAS SUPPLY
• Check the mnometer zero point is correct.
• Connect the mnometer to the cooktop
pressure point. This is locted on the regultor.
• Turn on the gs supply nd electricity nd try to
ignite the gs.
NOTE:
It will tke dditionl time to light the gs for the
rst time s ir needs to be purged from the pipes.
With the pplince operting check the outlet
pressure:
• When ll burners of the pplince re operting
t mximum.
• When the smllest burner of the pplince is
operting t minimum.
Under these conditions the outlet pressure should
not vry from the nominl outlet pressure
of 1.00kP by more thn ±0.20kP.
If the regultor ppers to not be performing
stisfctorily, then check the following points:
• If the outlet pressure is consistently too low
then the inlet pressure my be too low nd
djustment of n upstrem regultor my be
needed, or n upstrem regultor or vlve with
insucient ow cpcity my be present in
the gs supply line. If this is suspected then it
my be necessry to repet the checks whilst
mesuring both the inlet nd outlet pressure
to determine if the inlet pressure is in the
rnge 1.13 – 5kP.
• Check tht the regultor hs been tted to
the gs supply line in the correct orienttion,
the rrow on the bse of the body indictes the
direction of gs ow.
Once these checks hve been completed, if the
regultor still fils to perform in stisfctory
mnner it should be replced.
Tble 3A – ECGG604W
Burner Type Nturl Gs
(Nominl Test point pressure: 1.00kP)
LPG
(Nominl Test point pressure: 2.75kP)
Injector Size
(mm)
Gs Consumption
(MJ/h)
Injector Size
(mm)
Gs Consumption
(MJ/h)
Auxiliary burner 0.93 4.3 0.58 4.3
Semi Rapid burner 1.15 6.3 0.68 6.3
Rapid burner ————
Wok burner 1.72 13.5 1.0 13.5
Tble 3B – ECGG905W
Burner Type Nturl Gs
(Nominl Test point pressure: 1.00kP)
LPG
(Nominl Test point pressure: 2.75kP)
Injector Size
(mm)
Gs Consumption
(MJ/h)
Injector Size
(mm)
Gs Consumption
(MJ/h)
Auxiliry burner 0.93 4.3 0.58 4.3
Semi Rpid burner 1.15 6.3 0.68 6.3
Rpid burner 1.5 10.8 0.9 10.8
Wok burner 1.72 13.5 1.0 13.5
Gs Connection (Continued)
esatto.house
19
This pplince is supplied set up for Nturl
Gs usge. A conversion kit is included with the
product for Universl LPG usge. The conversion
kit contins the pproprite injectors, 1 Brss Test
Point nd 1 LPG sticker.
Plese follow the procedure below if
conversion to suit UNIVERSAL LPG is required:
• Remove the hotplte trivets, burner cps nd
burner crowns to ccess the hotplte injectors.
Replce the fctory tted injectors with the
pproprite injectors, s supplied. Refer to
injector orice tble for injector sizes. The
injector size is stmped on the side of the
injector.
• Connect the brss test point dpter (pictured
opposite) using pproved gs thred tpe or
compound to the elbow tting.
• Turn on the gs supply nd t ech new
connection check for leks using sopy wter.
Ech hotplte vlve should be turned on, one
t time, nd the injector hole blnked o for
severl seconds.
• With the pplince operting check the outlet
pressure when ll burners of the pplince
re operting t mximum, when the smllest
burner of the pplince is operting t
minimum.
Under these conditions the outlet pressure
should not vry from the nominl outlet
pressure of 2.60kP by more thn ±0.52kP.
• If the regultor ppers to not be performing
stisfctorily then check the following points:
• If the outlet pressure is consistently too low
then the inlet pressure my be too low nd
djustment of n upstrem regultor my be
needed, or n upstrem regultor or vlve with
insucient ow cpcity my be present in the
gs supply line.
• If this is suspected then it my be necessry to
repet the checks whilst mesuring both the
inlet nd outlet pressure to determine if the
inlet pressure is in the rnge 2.75 – 7.00kP.
• One by one, turn the knobs to minimum nd
screw in the bypss screw (ccessible when
the knob is removed) until smll stble me
results; length of 3-4mm. Turn the knob to
mximum nd then bck to minimum to ensure
tht the correct minimum me is mintined.
• Attch the LPG sticker to the cooker, ner the
gs supply inlet. Cover the Nturl Gs lbel
tht is fctory tted.
LPG Conversion
User Manual
20
Electricl Connection
ELECTRICAL CONNECTION
220240 VOLTS
The pplince is supplied with stndrd 7.5 Amp
service cord terminted by 3-pin plug for
connection to stndrd 10 Amp household
socket. The electricl supply is required to power
the electronic ignition system.
Note: It will be necessry for servicing purposes
to disconnect the electricl power supply. The
power point should therefore be ccessible fter
the pplince is instlled, s specied in the locl
wiring regultions.
Digrm 1A 1B (depending on your model)
re schemtics of the wiring in the pplince.
IMPORTANT:
This pplince must be erthed.
This pplince is designed to be connected to
220-240V, 50Hz-60Hz AC electricity supply.
The wires in the mins led re coloured in
ccordnce with the following code:
1. Green/Yellow = Erth
2. Blue = Neutrl
3. Brown = Live
IMPORTANT: The wire which is coloured
Green/Yellow must be connected to the terminl
which is mrked with the letter E or by the
Erth symbol.
WARNING: When the power cord is dmged it
must be replced by the mnufcturer, its service
gent or similrly qulied persons in order to
void hzrd.
Digrm 1A – ECGG604W
Digrm 1B – ECGG905W
Electrical Connection
- Green/yellow = Earth
- Blue = Neutral
- Brown = Live
22
■ This appliance is designed to be connected to a 220-240V, 50Hz-60Hz AC electricity supply.
Ŷ7KHZLUHZKLFKLVFRORXUHGJUHHQDQG\HOORZPXVWEHFRQQHFWHG
WRWKHWHUPLQDOZKLFKLVPDUNHGZLWKWKHOHWWHU(RUE\WKHHDUWK
V\PERO
ʄ:,5
When the power cord is damaged it must be replaced by the manufacturer to produce,
customer service agent or similarly qualified personnel.
,1*',$*5$0
Ŷ7KLVDSSOLDQFHPXVWEHHDUWKHG
Ŷ7KHZLUHVLQWKHPDLQVOHDGDUHFRORXUHGLQDFFRUGDQFHZLWKWKHIROORZLQJFRGH
Switch 1
Switch 2
AC INPUT
Switch 3
Switch 4
IGNITION
L
E
N
24
Installation
Electrical Connection
Electrical Connection
- Green/yellow = Earth
- Blue = Neutral
- Brown = Live
22
■ This appliance is designed to be connected to a 220-240V, 50Hz-60Hz AC electricity supply.
Ŷ7KHZLUHZKLFKLVFRORXUHGJUHHQDQG\HOORZPXVWEHFRQQHFWHG
WRWKHWHUPLQDOZKLFKLVPDUNHGZLWKWKHOHWWHU(RUE\WKHHDUWK
V\PERO
ʄ:,5
When the power cord is damaged it must be replaced by the manufacturer to produce,
customer service agent or similarly qualified personnel.
,1*',$*5$0
Ŷ7KLVDSSOLDQFHPXVWEHHDUWKHG
Ŷ7KHZLUHVLQWKHPDLQVOHDGDUHFRORXUHGLQDFFRUGDQFHZLWKWKHIROORZLQJFRGH
Switch 1
Switch 2
AC INPUT
Switch 3
Switch 4
IGNITION
L
E
N
Model: ICGG604W Model: ICGG755W & ICGG905W
Wiring Diagrams
Electrical Connection
- Green/yellow = Earth
- Blue = Neutral
- Brown = Live
22
■ This appliance is designed to be connected to a 220-240V, 50Hz-60Hz AC electricity supply.
Ŷ7KHZLUHZKLFKLVFRORXUHGJUHHQDQG\HOORZPXVWEHFRQQHFWHG
WRWKHWHUPLQDOZKLFKLVPDUNHGZLWKWKHOHWWHU(RUE\WKHHDUWK
V\PERO
ʄ:,5
When the power cord is damaged it must be replaced by the manufacturer to produce,
customer service agent or similarly qualified personnel.
,1*',$*5$0
Ŷ7KLVDSSOLDQFHPXVWEHHDUWKHG
Ŷ7KHZLUHVLQWKHPDLQVOHDGDUHFRORXUHGLQDFFRUGDQFHZLWKWKHIROORZLQJFRGH
Switch 1
Switch 2
AC INPUT
Switch 3
Switch 4
IGNITION
L
E
N
Electrical Connection
- Green/yellow = Earth
- Blue = Neutral
- Brown = Live
22
■ This appliance is designed to be connected to a 220-240V, 50Hz-60Hz AC electricity supply.
Ŷ7KHZLUHZKLFKLVFRORXUHGJUHHQDQG\HOORZPXVWEHFRQQHFWHG
WRWKHWHUPLQDOZKLFKLVPDUNHGZLWKWKHOHWWHU(RUE\WKHHDUWK
V\PERO
ʄ:,5
When the power cord is damaged it must be replaced by the manufacturer to produce,
customer service agent or similarly qualified personnel.
,1*',$*5$0
Ŷ7KLVDSSOLDQFHPXVWEHHDUWKHG
Ŷ7KHZLUHVLQWKHPDLQVOHDGDUHFRORXUHGLQDFFRUGDQFHZLWKWKHIROORZLQJFRGH
Switch 1
Switch 2
AC INPUT
Switch 3
Switch 4
IGNITION
L
E
N
Switch 5
Electrical Connection
- Green/yellow = Earth
- Blue = Neutral
- Brown = Live
22
■ This appliance is designed to be connected to a 220-240V, 50Hz-60Hz AC electricity supply.
Ŷ7KHZLUHZKLFKLVFRORXUHGJUHHQDQG\HOORZPXVWEHFRQQHFWHG
WRWKHWHUPLQDOZKLFKLVPDUNHGZLWKWKHOHWWHU(RUE\WKHHDUWK
V\PERO
ʄ:,5
When the power cord is damaged it must be replaced by the manufacturer to produce,
customer service agent or similarly qualified personnel.
,1*',$*5$0
Ŷ7KLVDSSOLDQFHPXVWEHHDUWKHG
Ŷ7KHZLUHVLQWKHPDLQVOHDGDUHFRORXUHGLQDFFRUGDQFHZLWKWKHIROORZLQJFRGH
Switch 1
Switch 2
AC INPUT
Switch 3
Switch 4
IGNITION
L
E
N
Gas adjustment
1
2
Injector
Control handle
Tap
Sealing ring
23
Remove the pan support, Burner lid and Flame spreader.
Unscrew the injector using a 7mm box spanner and
replace it with the stipulated injector for new gas
supply. Carefully reassemble the all components.
After injectors are replaced, it is advisable to strongly
tighten the injector in place.
Adjustment of minimum level of the flame.
Turn the taps down to minimum.
-
Remove the knob from the tap and place a small
bladed screwdriver in the centre of the tap shaft.
The correct adjustment is obtained when the flame
has a length of about 3 - 4 mm.
-
For butane
/ propane gas, the adjusting screw must
Make sure that the flame does not go out by
quickly turning from maximum flow to minimum
flow. If it does then remove the control knob and
make further adjustments to the gas flow, testing it
again once the adjustment has been made.
Repeat this process for each one of the gas taps.
be tightly screwed in.
Refit the control knob.
Ŷ7DNHSUHFDXWLRQVRQWKHRSHUDWLRQVDQGDGMXVWPHQWVWREHFDUULHGRXWZKHQ
FRQYHUWLQJIURPRQHJDVWRDQRWKHU
Ŷ$OOZRUNPXVWEHFDUULHGRXWE\DTXDOL¿HGWHFKQLFLDQ
Ŷ%HIRUH\RXEHJLQWXUQRIIWKHJDVDQGHOHFWULFLW\VXSSO\WRWKHDSSOLDQFH
-
Ŷ
%HIRUHSODFLQJWKHEXUQHUV
EDFNRQWKHWRSSODFHPDNHVXUH
WKDWWKHLQMHFWRULV QRWEORFNHG
FDUULHGRXWDIWHUJDVFRQYHUVLRQ
VXFKDVVRDSZDWHURUJDV
DTXDOL¿HGWHFKQLFLDQRULQVWDOOHU
KDVWRPDUN³9´RQWKHULJKWJDV
FDWHJRU\
WRPDWFKZLWKWKH
VHWWLQJLQUDWLQJSODWH
5HPRYHWKHSUHYLRXV
VHWWLQJ³9´PDUN
LQWKHHYHQWRIDPDOIXQFWLRQ
FKDQJHWKHZKROHWDS
Ŷ
$IXOORSHUDWLRQDOWHVWDQGDWHVW
IRUSRVVLEOHOHDNDJHVPXVWEH
Ŷ
$IWHUFRPSOHWLQJFRQYHUVLRQ
GHWHFWRU
Change the injector of the burners.
ŶDo not dismantle the tap shafe:
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Esatto ECGG604W User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Inalto ICG905W User manual
-
-
Solt GGSCC6004K User manual
-
-
-
-
Westinghouse WVE615SWHG644SA User manual
-
Westinghouse WHG646SA User manual
-
Electrolux EHG955BD User manual
-