Esatto EOCG60 User manual

Type
User manual
Version
V1.3 0124
Everything you need
for your Gs Cooktop
is in this User Mnul
Model/s
ECG604E
User Manual
2
Welcome
Congrtultions on purchsing your new Gs Cooktop. The Estto brnd is
proudly distributed within Austrli by Residenti Group Pty Ltd.
Plese refer to the wrrnty crd t the rer of this mnul for informtion
regrding your products prts nd lbour wrrnty, or visit us online t:
www.residenti.group
At Residenti Group, we re customer obsessed nd our Support Tem re
there to ensure you get the most out of your pplince. Should you wnt to
lern more bout your new gs cooktop, it's fetures or importntly tking
cre of the pplince, our Support Tem re here to help.
You cn use our online Support Centre t nytime by visiting:
http://support.residentigroup.com.u
Or you cn contct us vi phone by diling: 1300 11 HELP (4357).
It is importnt tht you red through the following use nd cre mnul
thoroughly to fmilirise yourself with the instlltion nd opertion
requirements of your pplince to ensure optimum performnce.
Agin, thnk you for choosing n Estto pplince nd we look forwrd
to being of service to you.
Kind Regrds,
The Residenti Tem
Residenti roup
Head Office
165 Brkly Avenue
Burnley, Victori
Austrli 3121
ACN
600 546 656
Online
residenti.group
www.estto.house
@estto.house
Postage
PO Box 5177
Burnley, Victori
Austrli 3121
Telephone
1300 11 4357
www.estto.house
esatto.house
3
Pge 2
Welcome
Pge 4
Sfety Instructions
Pge 6
Product Overview
Pge 7
Before First Use
Pge 8
Using Your
Cooktop
Pge 9
Burners
Pge 10
Clening  Cre
Pge 11
Troubleshooting
Pge 12
Technicl Dt
Pge 13
Instlltion
Instructions
Pge 16
Gs Connection
Pge 19
LPG Conversion
Pge 20
Electricl
Connection
Pge 21
Testing Applince
Opertion
Pge 23
Purchse Detils
Pge 24
Wrrnty
Contents
User Manual
4
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP
FOR FUTURE REFERENCE
Red this mnul thoroughly before rst use,
even if you re fmilir with this type of product.
The sfety precutions enclosed herein reduce
the risk of re, electric shock nd injury when
correctly dhered to. Mke sure you understnd
ll instructions nd wrnings.
Keep the user mnul in  sfe plce for future
reference, long with the completed wrrnty
crd nd purchse receipt. If you sell or trnsfer
ownership of this product, pss on these
instructions to the new owner.
Alwys follow bsic sfety precutions nd
ccident prevention mesures when using n
electricl pplince. The following sttements you
will see in this booklet hve these menings:
WARNING: Indicting informtion concerning
your personl sfety.
CAUTION: Indicting informtion on how
to void dmging the pplince, benchtop
or cbinetry.
IMPORTANT: Indicting tips nd informtion
bout use of the pplince.
USAGE CONDITIONS AND RESTRICTIONS
Domestic use only: This pplince is intended
for indoor household use only. It is not intended
for commercil, industril or outdoor use. It is
not intended for use in  recretionl vehicle.
Purpose: Do not use this pplince for nything
other thn its intended purpose. Other uses re
not recommended nd my cuse re, electric
shock or personl injury.
Attchments: The use of ttchments is not
recommended by the pplince mnufcturer
nd distributor s they my be hzrdous.
Improper use: Dmge due to improper use,
or repirs mde by unqulied personnel will
void your wrrnty. We ssume no libility
for ny eventul dmges cused by misuse
of the product or noncomplince with these
instructions.
BEFORE USING YOUR APPLIANCE
This mnul explins the proper use of your new
Estto cooktop. Plese red this mnul crefully
before using the product. This mnul should be
kept in  sfe plce for hndy reference.
This rngehood is  domestic pplince which
hs been mnufctured nd tested to comply
with Austrlin nd New Zelnd Stndrd
AS/NZS 5263.
This cooktop must only be instlled in ccordnce
with the instructions provided. Incorrect
instlltion my cuse hrm to persons, dmge
property nd void the product’s wrrnty.
Red the following crefully to void dmge
or injury.
IMPORTANT: Check for ny dmge or
mrks. If you nd the pplince is dmged
or mrked, you must report it within 7 dys if
you wish to clim for dmge/ mrks under the
mnufcturer’s wrrnty. This does not ect
your sttutory rights.
WARNING: Follow these instructions crefully
to void injury or dmge to your pplince.
Do not llow pots to boil dry, s dmge to both
pn nd cooktop my result.
Do not operte the cooktop for n extended
period without  pot or pn on the burner.
Do not llow lrge cookwre to overhng the
cooktop onto djcent benchtop. This will cuse
scorching to the benchtop surfce.
Do not llow cooking pots or pns to intrude
into the re which is close to the controls.
Ensure burner bodies nd trivets re properly
locted on the cooktop (i.e. correctly ssembled
nd positioned).
CAUTION: Follow these instructions crefully
to void n electric shock or re.
Sfety Instructions
esatto.house
5
It is importnt to use your cooktop sfely. Check
these sfety points before using your cooktop.
This pplince is not intended for use by
persons (including children) with reduced
physicl, sensory or mentl cpbilities, or lck
of experience nd knowledge, unless they hve
been given supervision or instruction concerning
use of the pplince by  person responsible for
their sfety.
Children should be supervised to ensure they do
not ply with this pplince.
During use, this pplince becomes hot.
Cre should be tken to void touching hot
surfces. To void burns, young children should
be kept wy.
Prolonged intensive use of the pplince my
cll for dditionl ventiltion, for exmple
opening of  window, or incresing the level of
mechnicl ventiltion where present.
Keep vents cler of obstructions.
This pplince must not be used s 
spce heter.
Keep vents cler of obstructions.
In order to void  re, this pplince must be
kept clen.
Do not spry erosols in the vicinity of this
pplince while it is in opertion.
Do not store mmble mterils on or under
this pplince, e.g. erosols.
Do not remove the trivet nd enclose the burner
with  wok stnd s this will concentrte nd
deect het onto the burner.
Do not use lrge pots or hevy weights
which cn bend the trivet or deect me onto
the burner.
Do not plce nything, e.g. sbestos mt
between pn nd trivet s serious dmge to
the cooktop my occur.
For mximum stbility, ensure pots nd pns re
centrlly locted on the trivets.
Hndles should be turned wy from the front
of the bench to void ccidents.
Do not modify this pplince.
This pplince cnnot be instlled on mrine
crft, crvns or mobile homes.
Do not use this pplince s  spce heter.
This pplince is not suitble for instlltion
with ftermrket lids or covers.
CAUTION: In the event of  gs lek, tke the
following ctions:
Do not turn on the room light.
Do not switch on/o ny electricl pplinces
nd do not touch ny electric plugs.
Do not use  telephone.
1. Stop using the product nd close the
middle vlve.
2. Open the window to ventilte.
3. Contct our service centre by using  mobile
phone outside.
NOTE: The fuel gs contins mercptn. In the
event of  gs lek, it will smell like rotten eggs or
grlic—even if there is only 1/1000th of the gs is
in the ir.
UNPACKING
During trnsporttion, protective pckging ws
used to protect the pplince ginst ny dmge.
After unpcking, plese dispose of ll elements of
pckging in  wy tht will not cuse dmge to
the environment.
All mterils used for pckging the pplince re
environmentlly friendly; they re 100% recyclble
nd re mrked with the pproprite symbol.
CAUTION: During unpcking, the pckging
mterils (polythene bgs, polystyrene pieces,
etc.) should be kept out of rech of children.
DISPOSAL OF THE APPLIANCE
Old pplinces should not simply be disposed
of with norml household wste nd should be
delivered to  collection nd recycling centre for
electric nd electronic equipment. A symbol shown
on the product, the instruction mnul or the
pckging shows tht it is suitble for recycling.
Mterils used inside the pplince re recyclble
nd re lbelled with informtion concerning this.
By recycling mterils or other prts from used
devices you re mking  signicnt
contribution to the protection of
our environment. Informtion on
pproprite disposl centres for
used devices cn be provided by
your locl uthority.
User Manual
6
THE BURNER
Figure 2A
Product Overview
Burner Flme Ports
Ignition Sprk Plug
Flme Sfegurd Sensor
Skirt
Burner
Injector
Note: The images in this user manual are for reference only. Your appliance may appear dierently.
YOUR COOKTOP
Figure 1A ECG604E
A
B
D
E
C
E
F
KEY
A. Stinless Steel Hob
B. Burner Control Knobs
C. Enmel Trivets
D. Auxiliry Burner
E. Semi Rpid Burner
F. Rpid Burner
COOKTOP COMPONENTS
ACCESSORIES
Your Estto cooktop is supplied with:
1 × Cooktop
1 × Auxiliry pn support
1 × Gs regultor vlve
4 × Injectors
1 × Pressure joint
4 × Brckets
4 × Seling strips
4 × Screws
1 × Elbow
1 × User Mnul
1 × Quick Strt Guide
Figure 2B
esatto.house
7
INSTALLATION
An uthorised person must instll this pplince
nd MUST provide  Certicte of Complince.
This certicte should be retined long with
purchse informtion.
Before using the cooktop, ensure tht ll
pcking mterils re removed from the
pplince.
In order to void ny potentil hzrd, the
instlltion instructions in this booklet, nd ny
lbels on the pplince must be followed.
Ensure tht ll specied vents, openings nd ir
spces re not blocked.
Where the pplince is built into  benchtop,
the benchtop mteril must be cpble of
withstnding 85°C.
Ensure tht the duplicte rting lbel
(in the instruction pck) is ttched to 
redily ccessible djcent surfce, so tht the
cooktop cn be esily identied in the cse of
 service cll.
SERVICING
Servicing MUST only be crried out by
uthorised personnel.
To mintin sfe opertion, it is recommended
tht the product be inspected every ve yers
by n uthorised service person.
If the supply cord is dmged, it must be
replced by the mnufcturer, its service gent
or similrly qulied persons in order to void
 hzrd.
WARNING: Never instll  cooktop tht hs
been dmged. Plese contct our Service Tem
for ssistnce.
CLEANING
Alwys ensure the pplince is turned o
before clening.
This pplince contins luminium ttings.
Do not use custic bsed cleners.
Do not use stem cleners s this my cuse
moisture build up on electricl components.
Alwys clen the pplince immeditely fter
ny food spillge.
Do not plce ny components in  dishwsher.
Refer to the Clening Cre section on pge 10
of this user mnul for instructions on clening
nd mintining your stinless steel hob pnel.
CAUTION: Never plce burners or trivets in
 dishwsher.
Before First Use
User Manual
8
CONTROLS
Ech burner is controlled by  control knob.
The mrkings on the control pnel indicte which
burner the knob controls, nd the setting for tht
burner (See Figure 3).
STANDARD BURNER
Figure 3
NOTE: Gs controls turn nticlockwise from ‘OFF’
nd hve limited movement.
LIGHTING BURNERS
Electronic ignition: These cooktops re tted with
mins powered ignition. When the pplince hs
been connected nd the power is on, depressing
ny knob will relese sprks to ll burners.
CAUTION:
Keep hnds cler of burners when lighting.
If burner does not light within 5 seconds, turn
knob to ‘OFF’ position, wit to llow gs to
disperse nd then try lighting gin.
Burners MUST be operted between ‘1’ nd ‘9’
settings only.
To light  burner, the knob must be turned to the
position, then pushed down s fr s possible
for pproximtely 5 seconds. If the me goes
out when the knob is relesed simply depress the
knob gin, this time holding it down with slightly
more force for the sme length of time.
The height of the me cn be vried by turning
the control knob towrd the ‘1’ position.
In the bsence of electricl power, crry out the
ignition directly to the burner with  hnd held
ignition source.
Using Your Cooktop
Note: The diagrams in this user manual are for reference only. Your appliance may appear dierently.
esatto.house
9
Burners
CHOICE OF BURNER
For your convenience there is  choice of burners
to choose from:
A smll Auxiliry burner for specil low het
nd slow cooking. Minimum pn size 120mm
(Mximum 160mm).
Two medium Semi-Rpid burners for norml
cooking nd simmering. Minimum pn size
160mm (Mximum 180mm).
A lrge Rpid burner for fst heting nd lrge
pots nd pns. Minimum pn size 200mm
(Mximum 240mm).
To conserve gs plce the pn centrlly over the
burner nd djust the me so tht it does not
extend pst the edge of the pn (Figure 4). Do not
boil food too rpidly. A vigorous boil will not cook
food ny fster, nd will wste energy.
Figure 4
POTS AND PANS
All common pots nd pns; luminium,
stinless steel, cst iron, cermic, etc., my
be used on your new gs cooktop. Ensure tht
the pots or pns re stedy nd hve t bses
to void dngerous spill-over of hot liquids nd
wsted energy.
CAUTION:
Never use sbestos mts, wire mts or grids,
or luminium foil s it cn led to overheting,
crcked enmel or broken glss. The wrrnty will
be void if these items re used nd cuse  filure.
INCORRECT
A me tht is too high will
cuse gs wstge long
with possibility of heting
or dmge to your hndles.
CORRECT
For  lrge burner,
use  lrge utensil.
CORRECT
A correct me height will
sve gs usge.
CORRECT
For  smll burner,
use  smll utensil.
User Manual
10
Clening  Cre
CAUTION:
Ensure the pplince is o nd hs cooled down
before clening.
TRIVETS
Persistent stins my require rubbing with 
nylon scourer or cremed powder clensers.
Household enmel cleners re vilble, follow
the mnufcturer’s instructions in their use.
Hrsh brsive cleners, powder cleners,
steel wool or wx polishes should not be used.
STAINLESS STEEL HOB
The stinless steel hob my discolour over
time. This is norml due to the high cooking
tempertures. Ech time the cooktop is used, it
should be clen with  product tht is sfe nd
suitble for stinless steel, such s  soft cloth or
sponge with detergent nd wrm wter.
CAUTION: Try to clen up nd remove spillges
immeditely, while the hob is still hot! Especilly
sugr nd foods with  high sugr content
(eg. jm), melted plstics nd foil, ll of which
cn dmge the hob if left. Dry the the surfce
thoroughly fter clening.
If the hob requires extensive clening:
Use  hob clener product fter there hs been
sucient time llowed for the hob to cool.
Shke the bottle nd pply  smll quntity of
clener directly onto the hob.
Rub clen using  dmp cloth or pper towels.
Use  dmp cloth to remove ll remining
trces of the clener, which could otherwise
burn on when the hob is next used. Wipe the
hob dry.
TRIVETS AND BURNERS
These cn ll be lifted o nd removed for
seprte clening.
CAUTION: When retting the burners, ensure
tht they re correctly seted.
Ensure burners re thoroughly dried fter clening
or spillge. When clening the burners, ensure
tht ll the me ports re free of ny blockge
(refer to Figure 2B on pge 6). If necessry, use
 toothpick or brush to cler ports. The outer
surfce of the burner cps hve  polished
nish nd extr cre needs to be tken to void
scrtching this surfce during clening. In
instnces of hevy soiling, it my be necessry to
pply  non-brsive clening compound nd rub
with  cloth until the soiling is removed nd then
nish with  soft, dry cloth.
WARNING:
NEVER plce trivets or burners in the dishwsher.
IGNITION SPARK PLUG
FLAME SAFEGUARD SENSOR
Gently clen the ignition sprk plug nd me
sfegurd sensor with  dmp cloth to void
lighting diculties. Ensure tht they re dry
before use.
INJECTOR
Ensure the injector remins free of ny foreign
mteril. If necessry, use  thin piece of wire to
cler the orice.
esatto.house
11
Troubleshooting
If you hve  problem with the cooktop, check the tble below. You my be ble to solve the problem
nd this will sve you from pying for  service cll. You will hve to py for  service cll even in the
wrrnty period if the problem is one listed below.
Tble 1
PROBLEM POSSIBLE CAUSE SOLUTION
Burner will not light
even though the
sprker is working
Knob not held down long enough in ‘9’
position for me sfegurd.
Repet lighting procedure nd
hold knob down for 5 seconds in
‘9’ position. (Refer pge 8).
Gs supply vlve turned o. Turn on gs supply to pplince.
Wrong knob turned.
Ensure the knob you re turning
corresponds to the burner you
wnt to light.
Port blockge in ignition re. Ensure tht ports in ignition re
re clen nd dry.
Ignition sprk plugs wet or dirty. Dry or clen ignition sprk plugs.
No sprk is obtined
when control knob is
ctivted
Electricity supply is disconnected or
switched o.
Switch on electricity
or check fuses.
Ignition sprk plugs wet or dirty. Dry or clen ignition sprk plugs.
Flmes uneven or
tending to lift
Flme ports blocked or wet. Clen or dry me ports.
Burner cp incorrectly tted. Ensure this component is
tted correctly.
Flmes not stying on
when knob
is relesed
Knob not held down long enough
in ‘9’ position for me sfegurd
to engge.
Repet lighting procedure nd
hold knob down for 5 seconds in
‘9’ position. (Refer pge 8).
Knob not set between ‘1’ nd ‘9’ Knob MUST be set between
these positions.
Dirt or spillge on me
sfegurd sensor. Clen me sfegurd sensor tip.
Low het, slow
cooking
Incorrect cooking pot or pn
being used. Refer to Figure 4 (pge 9).
Benchtop or knobs
overheting
Incorrect cooking pot or pn
being used. Refer to Figure 4 (pge 9).
Pot or pn not locted
on burner properly.
Ensure pot or pn is centrlly
locted on burner.
User Manual
12
Technicl Dt
Tble 2
FEATURES ECG604E
Burners 4
Wok No
Ignition 220–240V~
Trivet Enmel
Hob Mteril 201 Grde Stinless Steel
Fetures Continous Ignition Device
Flme Filure Sfety Yes
Gs Connection G1/2 thred
Gs Types NG (LP conversion
kit supplied)
COOKTOP PHYSICAL DIMENSIONS mm
Width 600
Depth 510
Height 95
CUT OUT DIMENSIONS mm
Width 560
Depth 490
ENERGY RATING NG  MJ/h
Auxiliry burner 4.3
Semi Rpid burner × 2 6.3
Rpid burner 10.8
Totl MJ/h 27.7
This product is subject to continuous improvement,
specications are subject to change without prior notice.
This product was tested in accordance with the following standards:
AS/NZS 60335.2.102: 2018 & AS/NZS 60335.1: 2020
esatto.house
13
Instlltion Instructions
INSTALLATION PROCEDURE
Do not modify this pplince.
WARNING: This pplince must be instlled
by n uthorised technicin or instller.
Prior to instlltion, ensure tht the locl distribution conditions (nture of the gs nd
gs pressure) nd the djustment of the pplince re comptible.
The djustment conditions for this pplince re stted on the lbel (or dt plte)
This pplince is not connected to  combustion products evcution device. It
should be instlled nd connected in ccordnce with current instlltion regultions.
Prticulr ttention should be given to the relevnt requirements regrding ventiltion.
Before instlling, turn o the gs nd electricity supply to the pplince.
All pplinces contining ny electricl components must be erthed.
Ensure tht the gs pipe nd electricl cble re instlled in such  wy tht they do not
touch ny prts of the pplince which my become hot.
Gs pipe or connector shouldn’t be bent or blocked by ny other pplinces.
Check the dimensions of the pplince s well s the dimensions of the gp to be cut in
the kitchen unit.
The pnels locted bove the work surfce, directly next to the pplince, must be mde
of non-mmble mteril. Both the strtied surfcing nd the glue used to secure it
should be het resistnt, to prevent deteriortion.
Turn on pplince tp nd light ech burner. Check for  cler blue me without yellow
tipping nd if burners show ny bnormlities check the following;
Burner lid is on correctly
Flme spreder is positioned correctly
Burner verticlly ligned with injector end
A full opertionl test nd test for possible lekges must be crried out by the instller
fter instlltion.
The exible hose shll be tted in such  wy tht it cnnot come into contct with 
movble prt of the housing unit nd does not pss through ny spce susceptible of
becoming congested.
Grese crnes produced t the fctory to meet the requirement of ll life hob.
CAUTION: Cooktops re supplied set up for nturl gs (NG). To use on LPG, the injectors
must be chnged using the conversion kit supplied. Refer LPG Conversion on pge 19.
Figure 5 ECG604E
600
510
490
95
560
Gas Supply
Connection
200
60
200
User Manual
14
INSTALLATION PROCEDURE
When tting the cooktop with  rngehood bove, refer to the instlltion requirements
of the rngehood for clernces required.
This pplince is to be built into  kitchen unit or 600mm worktop, provided the
following minimum distnces re llowed;
The edges of the cooktop must be  minimum distnce of 60mm from  side or rer wll.
Adjcent wlls, cupbords nd protection for combustible mterils: Ensure tht the
pplince is instlled in ccordnce with AS/NZS 5601.1, or AS/NZS 5601.2 with regrd
to clernces to combustible surfces nd mterils, nd clernces to rngehoods nd
exhust fns.
Clernces to combustible surfces my be reduced if combustible surfces re
protected in ccordnce with AS/NZS 5601.1, or AS/NZS 5601.2.
400mm between the cooktop surfces, providing tht the underside of the horizontl
surfce is in line with the outer edge of the cooktop. If the underside of the horizontl
surfce is lower thn 400mm, then it must be t lest 50mm wy from the outer edges
of the cooktop.
50mm clernce round the pplince nd between the cooktop surfce nd ny
combustible mterils.
A brrier must be instlled to prevent ccidentl contct with the cooktop bse,
where the bse of the cooktop is ccessible from below (i.e. Inside  cupbord, etc.).
A minimum clernce of 25mm must be mintined between the bse nd the brrier.
This brrier my be mde of ny non-combustible, rigid mteril.
You must hve  gp of t lest 25mm nd t most 74mm between the underneth of
the pplince nd ny surfce tht is below it.
Brrier protection is not necessry if the product is instlled bove n underbench oven
or similr pplince nd/or if the cupbord construction is such tht the underside of
the cooktop is not ccessible.
An oven must hve forced ventiltion to instll  cooktop bove it. Check the dimensions
of the oven in the instlltion mnul.
The cut out size must obey the indiction.
Ensure that there is an earthed power outlet within 900mm of the rear right hand side of
the cooktop when installed. This should be accessible at all times.
A self-adhesive Foam Tape has been provided to act as a sealing agent and is to be
placed around the edge of the hob underside. Ensure that there are no gaps in the Foam
Tape. Take care to ensure that the seals meet without overlapping. The thickness of this
Foam Tape is 3mm and the width is 10mm.
Positioning
The edges of the hob must be a minimum distance of mm from a side or
rear wall.
700 mm between the highest point of the hob surface (including the burners)
and the underside of any horizontal surface directly above it.
400 mm between the hob surfaces, providing that the underside of the
horizontal surface is in line with the outer edge of the hob. If the underside of
the horizontal surface is lower than 400 mm, then it must be at least 50 mm
away from the outer edges of the hob.
50 mm clearance around the appliance and between the hob surface and any
combustible materials.
45 mm
60
You must have a gap of at least 25 mm and at most 74 mm between
the underneath of the appliance and any surface that is below it.
16
o
o
o
o
o
CLEARANCES REQUIRED
WHEN FITTING THE HOB
WITH A COOKER HOOD ABOVE
900mm
700mm
400mm
400mm
FO 0813
60mm
480mm
in
0
.
0mm
M
2
This appliance is to be built into a kitchen unit or 600mm worktop,providing
the following minium distances are allowed;
- An oven must have forced ventilation to install a hob above it.
- Check the dimensions of the oven in the installation manual.
- The cut out size must obey the indication.
830mm
12
INSTALLATION INSTRUCTIONS CONT.
INSTALLING THE APPLIANCE
Remove the pan supports, the burner lid and
flame spreader and carefully turn the appliance
upside down and place it on a cushioned mat.
Take care that the Ignition devices and flame
supervision devices are not damaged in this
operation.
Apply the sponge provided around the edge of
the appliance.
Do not leave a gap in the sealing agent or
overlap the thickness.
WARNING!
DO NOT use a silicon sealant to seal the appliance
to the bench top.
This will make it difficult to remove the appliance
from the aperture in future, particularly if it needs to
be serviced.
1. Place the bracket (B) over the holes that match
the size of the screws. There are one set of screw
holes in each corner of the cooktop.
2. Slightly tighten a screw (C) through the bracket
(B) so that the bracket is attached to the hob, but
so that you can still adjust the position. Carefully
turn the hob back over and then gently lower it
into the aperture hole that you have cut out.
3. On the underneath of the hob, adjust the
brackets into a position that is suitable for
your worktop.
Then fully tighten the screws (C) to secure the hob
into position.
Installing the appliance
Bottom view
of the screws.There are one set of screw holes in each
corner of the hob (H) .
Slightly tighten a screw (C) through the bracket (B) so
that the bracket is attached to the hob, but so that you
can still adjust the position
.
.2 Carefully turn the hob back over and then gently lower
it into the aperture hole that you have cut out.
.3 On the underneath of the hob, adjust the brackets into
a position that is suitable for your worktop.
Then fully tighten the screws (C) to secure the hob into
position.
(A) SEALING STRIP
(C) SCREW (B) BRACKET
17
Remove the pan supports, the burner lid
and flame spreader and carefully turn the
appliance upside down and place it on a
cushioned mat.
Take care that the Ignition devices and
flame supervision devices are not damaged
in this operation.
2. Apply the sponge provided around the
edge of the appliance.
3.
1.
Do not leave a gap in the sealing agent or
overlap the thickness.
3ODFHWKHEUDFNHW %RYHUWKHKROHVWKDWPDWFKWKHVL]H
7KLVZLOOPDNHLWGLI¿FXOWWRUHPRYHWKH
DSSOLDQFHIURPWKHDSHUWXUHLQIXWXUH
SDUWLFXODUO\LILWQHHGVWREHVHUYLFHG
Do not use a silicon sealant to seal the
appliance against the aperture.
Installing the appliance
of the screws.There are one set of screw holes in each
corner of the hob (H) .
Slightly tighten a screw (C) through the bracket (B) so
that the bracket is attached to the hob, but so that you
can still adjust the position
.
.2 Carefully turn the hob back over and then gently lower
it into the aperture hole that you have cut out.
.3 On the underneath of the hob, adjust the brackets into
a position that is suitable for your worktop.
Then fully tighten the screws (C) to secure the hob into
position.
(A) SEALING STRIP
(C) SCREW (B) BRACKET
17
Remove the pan supports, the burner lid
and flame spreader and carefully turn the
appliance upside down and place it on a
cushioned mat.
Take care that the Ignition devices and
flame supervision devices are not damaged
in this operation.
2. Apply the sponge provided around the
edge of the appliance.
3.
1.
Do not leave a gap in the sealing agent or
overlap the thickness.
3ODFHWKHEUDFNHW %RYHUWKHKROHVWKDWPDWFKWKHVL]H
7KLVZLOOPDNHLWGLI¿FXOWWRUHPRYHWKH
DSSOLDQFHIURPWKHDSHUWXUHLQIXWXUH
SDUWLFXODUO\LILWQHHGVWREHVHUYLFHG
Do not use a silicon sealant to seal the
appliance against the aperture.
Instlltion Instructions (Continued)
esatto.house
15
Installing the appliance
Sponge
Bottom view
The thickness of the sponge is 3 mm.
The width of the sponge is 10 mm.
of the screws.There are one set of screw holes in each
corner of the hob (H) .
Slightly tighten a screw (C) through the bracket (B) so
that the bracket is attached to the hob, but so that you
can still adjust the position
.
.2 Carefully turn the hob back over and then gently lower
it into the aperture hole that you have cut out.
.3 On the underneath of the hob, adjust the brackets into
a position that is suitable for your worktop.
Then fully tighten the screws (C) to secure the hob into
position.
(A) SEALING STRIP
(C) SCREW (B) BRACKET
17
Remove the pan supports, the burner lid
and flame spreader and carefully turn the
appliance upside down and place it on a
cushioned mat.
Take care that the Ignition devices and
flame supervision devices are not damaged
in this operation.
2. Apply the sponge provided around the
edge of the appliance.
3.
1.
Do not leave a gap in the sealing agent or
overlap the thickness.
3ODFHWKHEUDFNHW %RYHUWKHKROHVWKDWPDWFKWKHVL]H
7KLVZLOOPDNHLWGLI¿FXOWWRUHPRYHWKH
DSSOLDQFHIURPWKHDSHUWXUHLQIXWXUH
SDUWLFXODUO\LILWQHHGVWREHVHUYLFHG
Do not use a silicon sealant to seal the
appliance against the aperture.
(A) SEALING STRIP
(B) CLAMP
(C) SCREW
WARNING: Do not use a silicon sealant to seal the appliance against the benchtop.
This will make it dicult to remove the appliance should the cooktop need a service.
Fit the pull down clamps supplied to ensure that the cooktop cannot move after installation.
Remove any excess seal visible after installation
WARNING: Failure to x the cooktop to the bench could result in loosening of the gas
connection through movement of the cooktop and a gas leak may result.
When benchtops re less thn 35mm in thickness, it my be necessry to t  spcer
between the benchtop nd ech clmp to ensure clmps cn be tightened suciently.
FITTING THE CLAMPS
Ensure tht the hob is free from ll burner pieces nd trivets. Plce the hob upside down
on  soft surfce to protect both the hob nd your worksurfce from dmge.
Plce the brcket (B) over the holes tht mtch the size of the screws. There re one
set of screw holes in ech corner of the hob. Slightly tighten  screw (C) through the
brcket (B) so tht the brcket is ttched to the hob whilst still llowing you to djust
it’s position.
Crefully turn the hob bck over nd then gently lower it into the perture hole tht you
hve cut-out in your benchtop.
On the underside of the hob, djust the brckets into  position tht is suitble for your
benchtop. Then fully tighten the screws (C) to secure the hob into position.
Figure 6
User Manual
16
Gs Connection
WARNING: This pplince must be instlled
nd connected in ccordnce with instlltion
regultions in force in the country in which the
pplince is to be used.
This pplince is supplied to run on LPG nd
nturl gs. Conversion for use on LPG nd
nturl gses must only be undertken by 
qulied person.
INSTALLATION OF APPLIANCE
Note: Wer protective gloves to t the hob.
CAUTION: lf it is necessry to djust or instll
the elbow, it is llowed only torque wrench with
9±1N.m, nd work on the Blck nut of mnifold
insted of on the elbow.
ADJUSTING THE DIRECTION OF ELBOW
After loosening the elbow, djust the elbow
interfce to the required direction s required,
nd keep the hexgonl hed of the elbow
motionless with  wrench. Use  9±1N.m torque
wrench to tighten the blck bolt of the gs inlet
pipe ssembly. Ensure tht the torque of the
wrench is within the required rnge to prevent
elbow brekge or dmge cused by excessive
force. After the instlltion is tightened, check
whether the prts re in good condition nd test
the ir tightness to ensure the tightness of the
instlltion. The instller is responsible for the
results of the process.
WARNING: Dnger of leks!
If ny connection is hndled, check the sel.
The mnufcturer is not lible for ny connection
leking, fter being hndled.
OPERATION ON N.G./S.N.G
This pplince is supplied for use with Nturl
Gs. However, it cn be converted for use with
LPG. Refer to LPG Conversion on pge 19.
SUPPLY PIPE SIZING
The totl hourly gs consumption for the
pplince is shown on the dt lbel. The
required supply pressure (i.e. t inlet to pplince
regultor) for ech gs type is shown on the dt
lbel, nd given in Tble 3 (pge 18). Use this
informtion in conjunction with the length of run,
number of elbows, tees nd bends, the vilble
service pressure nd the supply requirements of
other instlled pplinces to determine  suitble
pipe size.
For ssistnce in this mtter refer to the
pproprite section of AS/NZS 5601.1 or
AS/NZS 5601.2.
An AGA certied clss B or D exible connection
my be used to connect the cooktop in
ccordnce with AS/NZS 5601.1, in prticulr
section 5.9 nd cluse 6.10.1.8, or AS/NZS 5601.2,
in prticulr section 2.11.
Where  hose ssembly is used nd the cooktop
is in the instlled position, the hose ssembly shll
be suitble for connection to  xed consumer
piping outlet locted t  point 800 – 850mm
bove the oor nd in the region outside the width
of the pplince to  distnce of 250mm. The
point of connection to consumer piping must be
ccessible with pplince instlled.
ELBOW POSITIONING
It is possible to reposition the elbow if required
by loosening the locking nut nd elbow by using
two spnners. Re-tighten the entire ssembly
fter the elbow hs been repositioned. When
tting elbow to pplince, ensure tht the seling
wsher is tted.
Note to Instller: Assembly of elbow to mnifold
t rer of unit requires two spnners to secure
locking nut nd ensure lek free connection. For
this reson the elbow is best secured onto cooktop
mnifold before instlling unit into benchtop.
16
Installing the appliance
Remove the pan supports, the burner lid and flame spreader and carefully turn the appliance upside
down and place it on a cushioned mat.
Take care that the Ignition devices and flame supervision devices are not damaged in this operation.
Apply the sponge provided around the edge of the appliance.
Do not leave a gap in the sealing agent or overlap the thickness.
(A) SEALING STRIP
(C) SCREW (B) BRACKET
2.
1.
3.
2.
3.
Do not use a silicon sealant to seal the
appliance against the aperture.
This will make it difficult to remove the
appliance from the aperture in future,
particularly if it needs to be serviced.
Place the bracket (B) over the holes that match the
size of the screws.There are one set of screw holes in
each corner of the hob (H).Slightly tighten a screw (C)
through the bracket (B) so that the bracket is attached
to the hob, but so that you can still adjust the position.
Carefully turn the hob back over and then gently lower
it into the aperture hole that you have cut out.
On the underneath of the hob, adjust the brackets into
a position that is suitable for your worktop.
Then fully tighten the screws (C) to secure the hob into
position.
Gas Connection
This appliance must be installed and connected in accordance with installation
regulations in force in the country in which the appliance is to be used.
This appliance is supplied to run on LPG and natural gas. Conversion for use on LPG
and natural gases must only be undertaken by a qualified person.
Installation of appliance
Note: Wear protective gloves to
fit the hob.
Caution!
Black nut of
manifold
Elbow
Torque:
9±1N.m
lf necessary to adjust or
install the elbow, it is allowed
only torque wrench with
9±1N.m, and work on the
Black nut of manifold instead
of on the elbow.
9.0N.m
esatto.house
17
Gas Connection
Statutory requirements
This installation must conform with the following:
Manufacturer’s Installation instructions
Local Gas Fitting Regulations
Municipal Building Codes
Refer to AS/NZS 5601.1 for Gas Installations
S.A.A. Wiring Code
Local Electrical Regulations
Any other statutory regulations
Preparing to install
Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to
be inserted in a benchtop cutout. Only an officially authorised technician should
connect the appliance. Before you begin, turn off the gas and electricity supply.
19
A full operational test and a test for possible leakages must be
carried out by the fitter after installation.
Access to the whole length of the connection hose must be possible
and the gas hose must be replaced before its use before the end of
service life (indicated on the hose.)
Before Leaving-Check all connections for gas leaks with soap and
water.
DO NOT use a naked flame for detecting leaks. Ignite all burners both
individually and concurrently to ensure correct operation of gas
valves, burners and ignition. Turn gas taps to low flame position and
observe stability of the flame for each burner individually and all
together. Adhere the duplicate data plate to an accessible location
near the hotplate. When satisfied with the hotplate, please instruct
the user on the correct method of operation. In case the appliance
fails to operate correctly after all checks have been carried out, refer
to the auth orised service provider in your area.
Natural gas connection
95
115
LPG gas connection
pressure test point
pressure test point
Figure 7
REGULATOR
An pplince regultor is provided. The regultor
must be positioned so tht the pressure test nipple
is ccessible when the pplince is instlled.
Connect the gs supply to the ½” B.S.P. internl
thred inlet of the regultor. Refer to ‘bench
cutout’ Figure 5 for connection point position.
Regultors re supplied pre-djusted nd
congured by the component mker for use with
Nturl Gs.
The pplince instller is not required to
mke n djustment to obtin the correct outlet
pressure setting.
An rrow on the bse of the regultor indictes
the direction of gs ow when the inlet nd outlet
of the regultor is orientted correctly.
When the regultor hs been tted, check for
leks from the connections with sopy wter
—never  nked me.
ASSEMBLY OF THE REGULATOR
The ssembly of the regultor to the cooktop
mnifold is chieved vi the elbow union nd
seling wsher supplied, refer to Figure 7.
The ½” prllel thred connects to the mnifold,
nd the seling wsher is plced between the
mnifold end nd the t fce on the elbow.
The ½” tpered thred connects to the outlet of
the regultor, nd is seled on the thred using
pproved thred seling tpe or pproved thred
seling compound.
The inlet of the regultor is  ½” prllel thred
nd is connected to consumer piping or hose
ssembly.
Regultors re supplied pre-djusted nd
congured by the component mker for use with
Nturl Gs.
The pplince instller is not required to mke n
djustment to obtin the correct outlet
pressure setting.
An rrow on the bse of the regultor indictes
the direction of gs ow when the inlet nd outlet
of the regultor is orientted correctly. When the
regultor hs been tted check for leks from the
connections with sopy wter.
Where a flexible hose assembly is used, ensure it is
approved to AS/NZS 1869, Class B. Any hose assembly
used must be restrained from accidental contact with
the flue outlet of an under bench oven.
This hose assembly shall be suitable for connection to a
fixed consumer piping outlet located as follows:
Hotplates at a point 800 mm to 850 mm above the floor
and in the region outside the width of the appliance to a
distance of 250 mm.
After connecting to gas, check for leaks using soapy
solution, never a naked flame. Inlet connection region for flexible hose
Gas Connection
Install in accordance with relevant gas standards and/or codes of
practice applicable.
Connect the elbow fitting to the appliance gas manifold
connection, and check that seals between the elbow and
manifold connection are in place and in good condition.
For Natural gas: connect the natural gas appliance
regulator (pictured opposite) with integral test point using
approved gas thread tape or compound to the elbow
fitting.
For Universal LPG: connect the brass test point adaptor
(pictured opposite) using approved gas thread tape or
compound to the elbow fitting.
Ensure the supply connection point, test point and natural gas
regulator adjustment screw (for Natural gas installation) are
accessible for testing and/or adjustment with the hotplate in
the installed position.
20
Flexible Hose: If installing with a hose assembly, it must comply with AS/NZS
accordance with AS/NZS 5601.1.
Ensure that the hose does not contact the hot surfaces of the
hotplate,oven,dishwasher or any other appliance that may be installed
underneath or next to the hotplate.The hose should not be subjected to abrasion,
kinking or permanent deformation and should be able to be inspected along its
entire length with the cooktop in the installed position. Unions compatible with
the hose fittings must be used and all connections tested for gas leaks.The
supply connection point shall be accessible with the appliance installed.
WARNING: Ensure that the hose assembly is restrained from accidental contact
with the flue outlet of an underbench oven.
Gas Connection
1869,10mmID,class B or D,no more than 1.2m long and installed in
User Manual
18
CHECKING THE GAS SUPPLY
Check the mnometer zero point is correct.
Connect the mnometer to the cooktop
pressure point. This is locted on the regultor.
Turn on the gs supply nd electricity nd try to
ignite the gs.
NOTE:
It will tke dditionl time to light the gs for the
rst time s ir needs to be purged from the pipes.
With the pplince operting check the outlet
pressure:
When ll burners of the pplince re operting
t mximum.
When the smllest burner of the pplince is
operting t minimum.
Under these conditions the outlet pressure should
not vry from the nominl outlet pressure
of 1.00kP by more thn ±0.20kP.
If the regultor ppers to not be performing
stisfctorily, then check the following points:
If the outlet pressure is consistently too low
then the inlet pressure my be too low nd
djustment of n upstrem regultor my be
needed, or n upstrem regultor or vlve with
insucient ow cpcity my be present in
the gs supply line. If this is suspected then it
my be necessry to repet the checks whilst
mesuring both the inlet nd outlet pressure
to determine if the inlet pressure is in the
rnge 1.13 5kP.
Check tht the regultor hs been tted to
the gs supply line in the correct orienttion,
the rrow on the bse of the body indictes the
direction of gs ow.
Once these checks hve been completed, if the
regultor still fils to perform in  stisfctory
mnner it should be replced.
Tble 3 – ECG604E
Burner Type Nturl Gs
(Nominl Test point pressure: 1.00kP)
LPG
(Nominl Test point pressure: 2.75kP)
Injector Size
(mm)
Gs Consumption
(MJ/h)
Injector Size
(mm)
Gs Consumption
(MJ/h)
Auxiliry burner 0.93 4.3 0.58 4.3
Semi Rpid burner 1.15 6.3 0.68 6.3
Rpid burner 1.5 10.8 0.9 10.8
Gs Connection (Continued)
esatto.house
19
This pplince is supplied set up for Nturl
Gs usge. A conversion kit is included with the
product for Universl LPG usge. The conversion
kit contins the pproprite injectors, 1 Brss Test
Point nd 1 LPG sticker.
Plese follow the procedure below if  conversion
to suit UNIVERSAL LPG is required:
Remove the hotplte trivets, burner cps nd
burner crowns to ccess the hotplte injectors.
Replce the fctory tted injectors with the
pproprite injectors, s supplied. Refer to
injector orice tble for injector sizes. The
injector size is stmped on the side of the
injector.
Connect the brss test point dpter (pictured
opposite) using pproved gs thred tpe or
compound to the elbow tting.
Turn on the gs supply nd t ech new
connection check for leks using sopy wter.
Ech hotplte vlve should be turned on, one
t  time, nd the injector hole blnked o for
severl seconds.
With the pplince operting check the
outlet pressure when ll burners of the
pplince re operting t mximum, when
the smllest burner of the pplince is
operting t minimum.
Under these conditions the outlet pressure
should not vry from the nominl outlet
pressure of 2.60kP by more thn ±0.52kP.
If the regultor ppers to not be performing
stisfctorily then check the following points:
If the outlet pressure is consistently too low
then the inlet pressure my be too low nd
djustment of n upstrem regultor my be
needed, or n upstrem regultor or vlve with
insucient ow cpcity my be present in the
gs supply line.
If this is suspected then it my be necessry to
repet the checks whilst mesuring both the
inlet nd outlet pressure to determine if the
inlet pressure is in the rnge 2.75 7.00kP.
One by one, turn the knobs to minimum nd
screw in the bypss screw (ccessible when
the knob is removed) until  smll stble me
results;  length of 3-4mm. Turn the knob to
mximum nd then bck to minimum to ensure
tht the correct minimum me is mintined.
Attch the LPG sticker to the cooker, ner the
gs supply inlet. Cover the Nturl Gs lbel
tht is fctory tted.
LPG Conversion
User Manual
20
Electricl Connection
ELECTRICAL CONNECTION
220240 VOLTS
The pplince is supplied with  stndrd 7.5 Amp
service cord terminted by  3-pin plug for connection to  stndrd 10 Amp household
socket. The electricl supply is required to power the electronic ignition system.
Note: It will be necessry for servicing purposes to disconnect the electricl power supply.
The power point should therefore be ccessible fter the pplince is instlled, s specied
in the locl wiring regultions.
Digrm 1 is schemtics of the wiring in
the pplince.
IMPORTANT:
This pplince must be erthed.
This pplince is designed to be connected to  220-240V, 50Hz-60Hz AC electricity supply.
The wires in the mins led re coloured in ccordnce with the following code:
1. Green/Yellow = Erth
2. Blue = Neutrl
3. Brown = Live
IMPORTANT: The wire which is coloured
Green/Yellow must be connected to the terminl which is mrked with the letter E or by the
Erth symbol.
WARNING: When the power cord is dmged it must be replced by the mnufcturer, its
service gent or similrly qulied persons in order to void  hzrd.
Digrm 1 ECG604E
Electrical Connection
- Green/yellow = Earth
- Blue = Neutral
- Brown = Live
22
■ This appliance is designed to be connected to a 220-240V, 50Hz-60Hz AC electricity supply.
Ŷ7KHZLUHZKLFKLVFRORXUHGJUHHQDQG\HOORZPXVWEHFRQQHFWHG
WRWKHWHUPLQDOZKLFKLVPDUNHGZLWKWKHOHWWHU(RUE\WKHHDUWK
V\PERO
ʄ:,5
When the power cord is damaged it must be replaced by the manufacturer to produce,
customer service agent or similarly qualified personnel.
,1*',$*5$0
Ŷ7KLVDSSOLDQFHPXVWEHHDUWKHG
Ŷ7KHZLUHVLQWKHPDLQVOHDGDUHFRORXUHGLQDFFRUGDQFHZLWKWKHIROORZLQJFRGH
Switch 1
Switch 2
AC INPUT
Switch 3
Switch 4
IGNITION
L
E
N
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Esatto EOCG60 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI