Sauder 410147 is a full/queen headboard with a Shoal Creek Collection design. It comes with a detailed instruction manual that includes a guide on part identification, assembly tools required, and step-by-step assembly instructions with illustrations. It also features an optional video assembly tip available online. The headboard has a sturdy construction made from various materials, including wood, metal, and plastic. It is easy to assemble with the included hardware and tools and can be cleaned with furniture polish or a damp cloth.
Sauder 410147 is a full/queen headboard with a Shoal Creek Collection design. It comes with a detailed instruction manual that includes a guide on part identification, assembly tools required, and step-by-step assembly instructions with illustrations. It also features an optional video assembly tip available online. The headboard has a sturdy construction made from various materials, including wood, metal, and plastic. It is easy to assemble with the included hardware and tools and can be cleaned with furniture polish or a damp cloth.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-20
Français pg 21-23
Español pg 24-26
Lot # 376037 08/12/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Full/Queen Headboard
Shoal Creek Collection | 410147
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
You are getting sleepy.
Very sleepy.
Table of Contents Assembly Tools Required
2-3
4-5
6-20
21-23
24-26
27
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
410147 www.sauder.com/servicesPage 2
Part Identifi cation
å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F PANEL (1)
G SHELF (1)
H SMALL SHELF (2)
I BACK (1)
J DRAWER BOTTOM (2)
K DRAWER FRONT (2)
L DRAWER BACK (2)
M DRAWER SIDE (4)
Part Identifi cation
Now you know
our ABCs.
410147www.sauder.com/services
Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
H
J
K
L
M
M
M
Hardware Identifi cation
å Screws are shown actual size. You may receive extra hardware with your unit.
410147 www.sauder.com/servicesPage 4
NUT - 4
Y
WASHER - 4
Z
ANGLE BRACKET - 5
R
SUPPORT PIN - 4
W
CAM COVER - 4
X
TWIST-LOCK
®
FASTENER - 6
N
METAL PIN - 8
V
CAM DOWEL - 12
P2
HIDDEN CAM - 12
O2
KNOB - 2
T
HEADBOARD BRACKET - 2
Q
U
TAPE CARD - 5
S
DRAWER FRONT
BRACKET - 4
Hardware Identifi cation
å Screws are shown actual size. You may receive extra hardware with your unit.
410147www.sauder.com/services
Page 5
BLACK 9/16" LARGE HEAD SCREW - 22
DD
BLACK 1-1/4" FLAT HEAD SCREW - 4
AA
NAIL - 58
FF
BLACK 1/2" FLAT HEAD SCREW - 8
EE
GOLD 1" MACHINE SCREW - 2
CC
SILVER 1-1/4" BOLT - 4
117S
Step 1
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å
Assemble your unit on a carpeted fl oor or on the empty
carton to avoid scratching your unit or the fl oor.
å
To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (N) into the large holes in the UPRIGHTS (C and D).
410147 www.sauder.com/servicesPage 6
C
D
N
N
Do not tighten the TWIST-LOCK® FASTENERS in this step.
å
Push twelve HIDDEN CAMS (O2) into the ENDS (A and B),
PANEL (F), and SHELF (G). Then, insert the metal end of a
CAM DOWEL (P2) into each HIDDEN CAM.
Step 2
410147www.sauder.com/services
Page 7
A
B
F
G
Arrow
02
P2
Arrow
O2
P2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
(12 used)
Step 3
å
Using your hammer, gently tap four SUPPORT PINS (W) into
the holes in the ENDS (A and B) and UPRIGHTS (C and D).
410147 www.sauder.com/servicesPage 8
A
B
C
D
W
W
Remember:
Righty tighty.
Lefty loosey.
å
Fasten the UPRIGHTS (C and D) to the TOP (E). Tighten
two TWIST-LOCK® FASTENERS.
Step 4
410147www.sauder.com/services
Page 9
E
C
D
Angled edge
Long fi nished edge
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
How to use the SAUDER TWIST-LOCK
®
FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Step 5
å
Insert four METAL PINS (V) into each SMALL SHELF (H).
å
Insert the METAL PINS (V) in one end of the SMALL
SHELVES (H) into the holes in the UPRIGHTS (C and D).
410147 www.sauder.com/servicesPage 10
C
D
H
H
V
V
Finished edge
Finished edge
(8 used)
Unfi nished
surface
Unfi nished
surface
å
Fasten the SHELF (G) to the UPRIGHTS (C and D).
Tighten four TWIST-LOCK® FASTENERS.
Step 6
410147www.sauder.com/services
Page 11
C
D
G
Surface
with
HIDDEN
CAMS
Rounded edge
Step 7
å
Fasten the LEFT END (B) to the TOP (E) and SHELF (G).
Tighten four HIDDEN CAMS.
å
NOTE: Be sure the METAL PINS in the SMALL SHELF (H)
insert into the holes in the LEFT END (B).
410147 www.sauder.com/servicesPage 12
H
G
E
B
Surface
with
HIDDEN
CAMS
Angled edge
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Now might be a
good time to refresh
your drink.
å
Fasten fi ve ANGLE BRACKETS (R) to the PANEL (F). Use
fi ve BLACK 9/16" LARGE HEAD SCREWS (DD).
å
NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edge of the PANEL.
å
Carefully stand your unit on its TOP (E).
å
Fasten the PANEL (F) to the LEFT END (B). Tighten two
HIDDEN CAMS.
å
Then, fasten the PANEL (F) to the SHELF (G). Use fi ve
BLACK 9/16" LARGE HEAD SCREWS (DD).
Step 8
410147www.sauder.com/services
Page 13
R
F
F
B
G
Surface
with
HIDDEN
CAMS
Surface
with
HIDDEN
CAMS
BLACK 9/16" LARGE HEAD SCREW
(10 used in this step)
DD
Arrow
Minimum
190 degrees
Maximum
210 degrees
Step 9
å
Fasten the RIGHT END (A) to the TOP (E), SHELF (G), and
PANEL (F). Tighten six HIDDEN CAMS.
å
NOTE: Be sure the METAL PINS in the SMALL SHELF (H)
insert into the holes in the RIGHT END (A).
410147 www.sauder.com/servicesPage 14
F
A
E
G
H
Surface
without
HIDDEN
CAMS
Arrow
Minimum
190 degrees
Maximum
210 degrees
Angled edge
å
Carefully turn your unit over onto its front edges. Unfold
the BACK (I) and lay it over your unit.
å
Make equal margins along all four edges of the BACK (I).
Push on opposite corners of your unit if needed to make
it "square".
å
Fasten the BACK (I) to your unit using the NAILS (FF).
å
NOTE: Be sure to tap NAILS into the holes that line up
over the UPRIGHTS (C and D).
å
NOTE: Perforations have been provided for access
through the BACK. Carefully cut out the holes needed.
Step 10
410147www.sauder.com/services
Page 15
I
Unfi nished surface
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
These holes must line up over the UPRIGHTS (C and D).
NAIL
(38 used in this step)
FF
Step 11
å
Fasten the DRAWER FRONT BRACKETS (S) to the
DRAWER SIDES (M). Use four BLACK 1/2" FLAT
HEAD SCREWS (EE).
å
Then, fasten the DRAWER SIDES (M) to the
DRAWER FRONT (K). Use two BLACK 9/16"
LARGE HEAD SCREWS (DD).
å
Repeat this step for the other drawer.
410147 www.sauder.com/servicesPage 16
M
M
S
M
M
K
Finished edge
Finished edge
BLACK 9/16" LARGE HEAD SCREW
(4 used for the DRAWER FRONTS)
DD
Unfi nished edge
BLACK 1/2" FLAT HEAD SCREW
(8 used for the BRACKETS)
EE
Hole is closer to this edge.
å
Peel the double-sided TAPE from the TAPE CARD (U).
Apply fi ve pieces of TAPE to the DRAWER FRONT (K).
å
NOTE: You may want to crease the fl ap on the DRAWER
BOTTOM (J) before applying the BOTTOM to the
DRAWER FRONT (K).
å
Press the fl ap of the DRAWER BOTTOM (J) onto the
DRAWER FRONT (K).
å
Fasten the DRAWER BACK (L) to the DRAWER SIDES (M).
Use two BLACK 1-1/4" FLAT HEAD SCREWS (AA).
å
Repeat this step for the other drawer.
Step 12
410147www.sauder.com/services
Page 17
K
U
J
M
M
L
J
K
The fi nished surface should be
facing the DRAWER FRONT (K).
Finished
surface
Finished edge
Flap
Flap
BLACK 1-1/4" FLAT HEAD SCREW
(4 used in this step)
AA
Step 13
å
Carefully turn your drawer over and fold the DRAWER
BOTTOM (J) so it rests on the DRAWER BACK (L) and
DRAWER SIDES (M).
å
Fasten the DRAWER BOTTOM (J) to the DRAWER
BACK (L) and DRAWER SIDES (M). Use ten NAILS (FF).
å
Repeat this step for the other drawer.
410147 www.sauder.com/servicesPage 18
M
M
L
J
J
M
L
NAIL
(20 used in this step)
FF
Almost time to
celebrate! With a nap.
å
NOTE: You may want to crease the fl aps on the DRAWER
BOTTOM (J) before applying TAPE to the DRAWER BOTTOM.
å
Peel the double-sided TAPE from the TAPE CARD (U). Apply
four pieces of TAPE to the DRAWER BOTTOM (J) and stick the
fl aps of the DRAWER BOTTOM (J) onto the TAPE.
å
Fasten a KNOB (T) to the DRAWER FRONT (K). Use a GOLD 1"
MACHINE SCREW (CC).
å
Repeat this step for the other drawer.
Step 14
410147www.sauder.com/services
Page 19
J
U
J
K
T
Flap
GOLD 1" MACHINE SCREW
(2 used in this step)
CC
Want options? Customize
your item with add-on
hardware kits available
on sauder.com.
Step 15
å
Carefully stand your unit upright and insert the drawers into your unit.
å
Push a CAM COVER (X) onto each visible HIDDEN CAM.
å
Fasten the HEADBOARD BRACKETS (Q) to the ENDS (A and B). Use eight BLACK 9/16" LARGE HEAD SCREWS (DD).
Use the holes that are best suited for the height of your bedframe.
å
Fasten the bedframe to the HEADBOARD BRACKETS (Q). Use the SILVER 1-1/4" BOLTS (117S), NUTS (Y)
and WASHERS (Z).
å
This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
410147 www.sauder.com/servicesPage 20
A
B
Q
Q
X
20 lbs.
3 lbs.
3 lbs.
5 lbs.
5 lbs.
25 lbs.
(4 used)
To cover HIDDEN CAMS
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
DD
And to celebrate, why not share your success story?
117S
YZ
(4 of each used in this step)
WASHER NUTSILVER 1-1/4" BOLT
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Sauder 410147 is a full/queen headboard with a Shoal Creek Collection design. It comes with a detailed instruction manual that includes a guide on part identification, assembly tools required, and step-by-step assembly instructions with illustrations. It also features an optional video assembly tip available online. The headboard has a sturdy construction made from various materials, including wood, metal, and plastic. It is easy to assemble with the included hardware and tools and can be cleaned with furniture polish or a damp cloth.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Sauder 410147 Mode d'emploi
- español: Sauder 410147 Instrucciones de operación
Related papers
-
Sauder 420566 Operating instructions
-
-
-
-
-
-
-
-
-
Other documents
-
Hilti IFU-MH-SLT User guide
-
Regency LBC3032CH Operating instructions
-
-
Signature Sleep 3215198 Owner's manual
-
BLOTZ B28-SFW-201 Assembly Instructions
-
Hay Shelving Unit User manual
-
for Living 068-0410-4 Owner's manual
-
Franklin Brass P43971K-FB-CP User manual
-
Craftsman CMHT77633 Owner's manual
-
HOMESTOCK 99352 User manual
