Enwork Expanse Installation guide

Brand: Enwork

Model: Expanse

Type: Installation guide

Expanse

Installation Guide

PART NUMBER EAAXXX

CONFERENCE TABLES

TI0075

Expanse Conference Table Installation Guide – Rev 02.23

2TI0075 - Expanse Table Installation Instructions

1 — REQUIRED TOOLS AND SUPPLIES

Drill Philips Head Driver

Socket

Level Ratchet

Tape Measure

3TI0075 - Expanse Table Installation Instructions

2 — INCLUDED PARTS AND FASTENERS

.375-16 x 1.25"

Hex Head Bolt

.375-16 x 2.25"

Hex Head Bolt

.375-16 Square Nut

#12 x 1.00" Screw

25-20 Nut Base Plate Right Base Leg Left Base Leg

.375-16 x .50"

Hex Head Bolt

.375 -16 Easy Adjust Glide

25-20 x .50"

Draw Plate 1

Kickstand

.50-13 x 4.00"

Hex Head Bolt

Draw Plate 2

Zipbolt Surface Connector

4TI0075 - Expanse Table Installation Instructions

2 — INCLUDED PARTS AND FASTENERS

Extrusions

(Left, Mid, & Center)

Top Plate Assembly

End Cap Base Bottom Cover,

Inside

C Channel

Base Bottom Cover,

Outside

L Bracket

10-10 x 1" Truss Head SQ/

Phillips (SCREW 1)

5TI0075 - Expanse Table Installation Instructions

Assemble (4)Glides into the Baseplate.

Assemble the Inside Base Bottom

Cover using (3) 25-20 Nuts.

While standing on the base plate, Line up the connection

holes of the Top Plate Assembly with the Base Leg

assembly and attach using (8).375-16 x 1.25" bolts.

Note: Once the base is full assembled, place the provided

Kickstand under the assembly to keep it from falling forward.

Line up the Base Leg connection holes

with the holes on the Base Plate. Secure

together with (4).375-16 x 1.25" bolts.

Note: The angles cut into the attachment

plates should be facing the back.

3.1

3.3

3.2

3 — BASE ASSEMBLY

When the base assemblies are completed,

place them in there nal position.

3.4

6TI0075 - Expanse Table Installation Instructions

Extrusion Description

Top

Bottom

Outside

Inside

U-Channel

Space

Assemble the C Channels(EAM-1001-xx) into the

outside of the extrusion with the embossed "T"

facing up and the opening of the C facing outside.

Note: Do not tighten the bolts at this time

Place the extrusions in a clear area on a non marring

surface, in an order similar to their completed position.

Note: The Number of extrusions is dependent on table length.

Assemblies with 2 extrusions, assemble

the Left and Right Extrusion

Assemblies with 3 extrusions, skip to

section 5) Table Frame Assembly

Assemblies with 4 extrusions, assembly the Mid Extrusion

4.1

4.3

4.2

4 — EXTRUSION ASSEMBLY

Line up 2 of the threaded holes. Install (2) .25"-20 x

.50". and nger tighten. Repeat for all Extrusion.

Note: Do not tighten the bolts at this time

4.4

7TI0075 - Expanse Table Installation Instructions

Slide the next extrusion on to the C-Channel.

Assemble (1) Draw Plate 1, (1) Draw Plate 2

and (1) .50 -13 X 4.00" bolt into each Extrusion

connection hole and loosely tighten so the

extrusions line up ush on all sides.

Note: The extrusions must be aligned and square before they

are fully tightening. Adjust as necessary while tightening.

Once the Draw Plates are fully tightened, Fully tighten

the (2) .25-20 x .50" on top of the extrusion and

install and fully tighten (6) .25-20 x .50" into the top

and bottom of the extrusion (as shown in Fig 4.5).

Note: Depending on table length, Left & Right

Extrusions may be assembled at this point.

4.5 4.6

4 — EXTRUSION ASSEMBLY

8TI0075 - Expanse Table Installation Instructions

Place the fully assembled beams on the

Base Assembly, seating the channel of the

extrusion in to the U Channel of the base.

Note: leave the Kickstands in place

until the beams are fully secured.

Secure the ends of both extrusion to the Base

Assemblies using a .375-16 x 1.25" bolt, then proceed to

secure the extrusion with the using .375-16 x 2.25" bolts.

Repeat process for the other end of the table.

Align the holes of the assembled beams to

the holes of the assembled bases.

5.1

5.3

5.2

5 — TABLE FRAME ASSEMBLY

Slide the extrusions completely until the

surfaces meet. The C Channel holes should

alight with the top slots on the middle

extrusion assembly as shown below.

5.4

9TI0075 - Expanse Table Installation Instructions

Insert (2).25-20 x .50" into the extrusion slots

to secure the C-Channel and nger tighten.

Note: Do not tighten the bolts at this time

Loosely assemble the Top Connection Bracket, (2)

375-16 x .50" bolts, and (2) .375-16 Square Nuts

Insert the this assembly into the inside of the extrusions

There will be 2 for every Top Connection

Bracket (EAM-1024).

Install Draw Plate 1, Draw Plate 2 and a .50 -13 X 4.00"

bolt into each Extrusion connection hole and tighten.

Note: The extrusions must be aligned and square before they

are fully tightening. Adjust as necessary while tightening.

Fully tighten the bolts connecting the extrusion

to the base at this time (see Fig 5.5).

5.5

5.7

5.6

5 — TABLE FRAME ASSEMBLY

Position the 2 outer most Top Connection

Brackets 10"-16" from the end of the extrusion

and then evenly distribute the remaining

Brackets along the length of the extrusion.

Do not tighten yet. These may need to be

repositioned later in the assembly process.

5.8

10TI0075 - Expanse Table Installation Instructions

Loosely assemble the Extrusion Cap (EAM-2010-x) ,

(4) 375-16 x .50" bolts, and (4) .375-16 Square Nuts.

Press the end cap in all the way tight against the

end of the extrusion. Insure the back side of the

cap is ush with the end of the extrusion.

Fully tighten

5.9

5 — TABLE FRAME ASSEMBLY

11TI0075 - Expanse Table Installation Instructions

Place the worksurfaces on a non-marring surface

and attach the Embedded Braces to the routings

using the 10-10 x 1" Truss Head Phillips Screws.

Note: When attaching the braces, secure both end and

then use every other screw hole provided. This will aid

when attaching the work surface to the table frame.

Before attaching the work surface to the table tops

assembly, verify there is no interference with the Top

Connection Bracket and any power unit/cutouts.

Location of the Top Connection Bracket

can be adjusted as needed.

Tighten all of the brackets to the extrusion at this time.

Place the work surfaces onto the table frame. When

placing the end piece, insure there are no screw heads

interfering between the worksurface and the beams.

Any screw(s) causing interference may be removed.

This will only occur on the End Work Surface pieces.

Install and snuggly attach all tight joints. Align

work surfaces and fully tighten all tight joints.

Note: number of surfaces may vary depending on table length.

6.1

6.3

6.2

6 — TABLE TOP ASSEMBLY

Verify the work surface is aligned and centered.

Attach the work surface to the table assembly using

the Top Connection Bracket and #12 x 1.00 screws.

6.4

12TI0075 - Expanse Table Installation Instructions

Levelers are accessible through the

access hole on the tops of the base.

Place a level spanning both beams and

level the table across it’s depth.

Install the Outside Base Bottom

Covers between the Base legs.

Place a level on the beam between the 2

bases and level the table length rst.

7.1

7.3 7.4

7.2

7 — LEVELING

1.800.815.7251

enwork.com

12900 Christopher Dr. Lowell, MI 49331

Specications subject to change without notice.

Rev 02.2023

Enwork Expanse Installation guide

Enwork Expanse Installation guide

Enwork Expanse Installation guide

Related papers

Other documents