Vita Rosewood Arbor Operating instructions

Vita
Brand
Vita
Model
Rosewood Arbor
Type
Operating instructions
Rosewood Arbor
VA68894
ASSEMBLY
GUIDE
VER 1.7 11/19/19
1-844-880-8482
[email protected]
(44) 2038 687160
8:
00 AM
4:
00 PM EST
-
WWW.NEWENGLANDARBORS.COM
WWW.NEWENGLANDARBORS.CO.UK
NEA
X
PARTS LIST 4
TOOLS YOU WILL NEED - PRODUCT
DIMENSIONS
STEP 1 AND 2
STEP 3 AND 4
STEP 5 AND 6
STEP 7 AND 8
STEP 9 AND 10 (TEMPORARY
INSTALLATION)
STEP 11 (PERMANENT
INSTALLATION)
5
6
7
8
9
10
11
IN THIS GUIDE
ARCH KEYSTONE
12000 - X2
PARTS LIST
4 VER 1.7 11/19/19
ARCH RAFTER - 12003 - X6
RIGHT ARCH - 12002 - X2 LEFT ARCH - 12043 - X2
POST TRIM
12001 - X4
PRE-ASSEMBLED SIDE PANEL - 12004 - X2
METAL GROUND STAKES - 12006 - X4
20064 - SCREW B - 1 1/4IN (3.18CM) - X8 - TO ATTACH METAL STAKES TO ARBOR
20063 - SCREW C - 1 3/4IN (4.5CM) - X14 - TO ATTACH RAFTERS AND KEYSTONES TO
20065- BOLT AND T-NUT D - 2IN (5CM) - X8
TO FASTEN SIDE PANELS TO ARCH ASSEMBLY. TNUTS PREINSTALLED
20067 - BOLT AND T-NUT E - 1 3/4IN (4.5CM) - X4
FASTEN ARCH SECTIONS TOGETHER. TNUTS PREINSTALLED
20071 - SCREW A - 1 1/4IN (3.18CM) - X8 - TO SECURE POST TRIM CAPS TO ARBOR POSTS
WOOD BLOCK - X1
TOOLS YOU WILL NEED
VER 1.7 11/19/19 5
PRODUCT DIMENSIONS
88.7
(225.3CM)
84.5IN
(214.6CM)
42IN
(106.7CM)
47IN
(119.4CM)
26.5IN
(67.3CM)
20IN
(50.8CM)
24IN
(60.9CM)
1
2
6 VER 1.7 11/19/19
12000 - x2
12043 - x2
12002 - x2
20067 - x4
E
12002 x2
12043 x2
VER 1.7 11/19/19 7
3
4
20063 - x2
20063 - x12
12003 - x6
C
C
Stapled side of archs have to face each other, space between arches is 20in(50.8cm)
Align central trim
at arch marking
8 VER 1.7 11/19/19
5
6
12001 - x4
Screw holes to face
inside of arbor
VER 1.7 11/19/19 9
7
8
20065 - x8
D
A
20071 - x8
x1
Use wood block
provided to help
you hold post trim
in place! Repeat for
each trim
!
10 VER 1.7 11/19/19
9
10
B
20064 x8
Temporary Installation
Carefully push arbor
stakes into desired
ground area
12006 - x4
A
VER 1.7 11/19/19 11
11
B
Permanent Installation
For a permanent
installation, measure
four 8in (20.3cm)
holes in diameter, 44
1/2in (113cm) apart by
22in apart (56cm),
from center to center.
Dig each hole 14in
(36cm) deep.
Fill excavated holes
with mixed concrete
and carefully lift arbor
into place. Plumb and
level the arbor.
The posts should not
be set in the concrete.
Make sure to support
bottom part of you
lattice with bricks until
concrete has set. This
will stop your arbor
from sinking.
GROUND
CONCRETE
METAL STAKE
ARBOR POST
BRICKS
8IN
(20.3CM)
14IN
(36CM)
44 1/2in
(113cm)
22in (56cm)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Vita Rosewood Arbor Operating instructions

Vita
Brand
Vita
Model
Rosewood Arbor
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents