2. Vita
  3. Westwood Arbor

Vita Westwood Arbor, VA68890 Installation guide

  • Hello! I've reviewed the user guide for the Arbor Westwood VA68890. This document provides step-by-step instructions for assembling your new arbor, including a parts list, tool requirements, and guidance for both temporary and permanent installation. I'm ready to answer any questions you may have about the assembly process or features mentioned in the document.
  • What type of screws are used to attach the rafters to the arch?
    What are the dimensions between the holes for permanent installation?
    What size are the holes that need to be dug for permanent installation?
Westwood Arbor
VA68890
ASSEMBLY
GUIDE
VER 1.9 11/10/20
X
8am - 5pm ESThello@wearevita.com WWW.WEAREVITA.COM
18002829346
PARTS LIST 4
TOOLS YOU WILL NEED  PRODUCT
DIMENSIONS
STEP 1 AND 2
STEP 3 AND 4
STEP 5 AND 6 TEMPORARY
INSTALLATION
STEP 7 PERMANENT INSTALLATION
5
6
7
8
9
IN THIS GUIDE
PARTS LIST
4
ARCH RAFTER  12007  X6
PREASSEMBLED ARCH  12009  X2
PREASSEMBLED SIDE PANEL  12008  X2
METAL GROUND STAKES  12006  X4
BRACES  12005  X4
SCREW B  20064  1 1/4IN 3.18CM  X8  ATTACH GROUND STAKES TO POSTS
SCREW C  20068  2IN 5CM  X4  TO ATTACH THE FLAT PART OF THE BRACES TO ARBOR POSTS
SCREW D  20069  3IN 7.6CM  X4  TO ATTACH THE SWOOP PART OF THE BRACE TO ARBOR
SCREW E  20070  3 1/2IN 9CM  X8  TO ATTACH SWOOP PART OF ARCHS TO ARBOR POSTS
SCREW A  20037 1 1/2IN 3.8CM  X12  TO ATTACH RAFTERS TO ARCH
TOOLS YOU WILL NEED
5
PRODUCT DIMENSIONS
59in
(149.8cm)
78in
(198.1cm)
81.5in
(207cm)
42in
(106.6cm)
47in
(119.3cm)
85.5in
(217.2cm) 59in
(149.8cm)
3in
(7.6cm)
3in
(7.6cm)
13.5in
(34.3cm)
17.5in
(44.5cm)
5in
(12.7cm)
1
2
6
12009  X2
12008  X2
20070  X8 E
7
3
4
20068  X4
20069  X4
20037  X12
C
D
A
12005  X4
D
C
Screw in first, then
DC
Brace should in the center of the post.
12007  X6
8
5
6
20064  X8
12006 - x4
Temporary Installation
Carefully push arbor
stakes into desired
ground area
A
B
9
7
GROUND
CONCRETE
METAL STAKE
ARBOR POST
BRICKS
8IN
(20.3CM)
14IN
(36CM)
B
Permanent Installation
For a permanent
installation, measure
four 8in holes in
diameter, 44 1/2in
(113cm) apart by 15
1/2in apart (39.4cm),
from center to center.
Dig each hole 14in
(36cm) deep.
Fill excavated holes
with mixed concrete
and carefully lift arbor
into place. Plumb and
level the arbor.
The posts should not
be set in the concrete.
Make sure to support
bottom part of lattice
with bricks until
concrete has set. This
will stop your arbor
from sinking.
44 1/2in
(113cm) 15 1/2in
(39.4cm)
/