CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
D
D
A
A
S
S
H
H
D
D
I
I
S
S
A
A
S
S
S
S
E
E
M
M
B
B
L
L
Y
Y
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
2
2
0
0
0
0
0
0
-
-
0
0
1
1
H
H
y
y
u
u
n
n
d
d
a
a
i
i
A
A
c
c
c
c
e
e
n
n
t
t
1) Open drink holder half way and remove the (2) Phillips screws from this location.
2) Remove the (4) knobs from the heater, A/C controls.
3) Gently pull outward on the dash trim bezel starting at the bottom and work your
way to the top.
4) Open the glove box and depress both sides to lower the glove box out of
the way.
5) Disconnect the (1) heater control cable from the heater box, and remove the clip
from the cable (do not throw away)!
6)
Disconnect the (2) heater, A/C control cables from below the steering wheel. (You
will see a yellow gear with a cable and a white gear with a cable attached towards
the right side.) Detach the cables from the gears and remove the mounting clips
from the cables (do not throw away)! NOTE: The yellow gear connects to the
cable with the yellow foam covering.
7) Gently pull dash trim bezel forward.
8) Disconnect the Clock, Hazard, and Rear Defogger harnesses and lean the dash
trim bezel out of the way.
9) Remove the (4) Phillips screws securing the radio to the sub-dash.
10) Pull radio forward, disconnect the wire harness and antenna lead and remove
the radio.
K
K
I
I
T
T
A
A
S
S
S
S
E
E
M
M
B
B
L
L
Y
Y
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
1) Attach the left & right ISO mounting brackets to the left & right sides of the face
of kit.
2) Remove the trim ring from the after market radio.
3) Insert the aftermarket radio into the kit from the rear and attach to the kit using
the screws supplied with the aftermarket radio.
N
N
O
O
N
N
F
F
L
L
I
I
P
P
-
-
F
F
A
A
C
C
E
E
S
S
T
T
Y
Y
L
L
E
E
R
R
A
A
D
D
I
I
O
O
S
S
Adjust the radio forward or backwards until you have the desired look, and tighten
the side mounting screws.
F
F
L
L
I
I
P
P
-
-
F
F
A
A
C
C
E
E
S
S
T
T
Y
Y
L
L
E
E
R
R
A
A
D
D
I
I
O
O
S
S
Adjust the radio forward and tighten the side mounting screws and open the face
of the radio. If the face of the radio does not clear the lower lip of the kit, adjust
the radio backwards until the face of the radio opens unobstructed and tighten
the side mounting screws.
4) Wire the radio and install into dash using the (4) screws supplied with the kit.
5) Reassemble dash in reverse order of dash disassembly from steps 1 thru 8.
HYN-K1109 Mounting Kit
Hyundai
2000-01 ACCENT (Single ISO Application)
VEHICLE APPLICATIONS
©2009 AMERICAN INTERNATIONAL INDUSTRIES, INC.
Ver. 6/09
iHYNK1109
/
