Karl home MA436OT11C23GNAFAMZ-4285423 Operating instructions

Karl home
Brand
Karl home
Model
MA436OT11C23GNAFAMZ-4285423
Type
Operating instructions

This manual is also suitable for

The Karl home MA436OT11C23GNAFAMZ-4285423 is a mug press machine designed to transfer designs onto mugs and other cylindrical objects. It features adjustable temperature and pressure settings, allowing you to customize the pressing process for different materials and projects. With its user-friendly control panel, you can easily set the desired temperature and time, ensuring precise and consistent results. The machine also includes a built-in safety mechanism that prevents overheating and ensures safe operation.

The Karl home MA436OT11C23GNAFAMZ-4285423 is a mug press machine designed to transfer designs onto mugs and other cylindrical objects. It features adjustable temperature and pressure settings, allowing you to customize the pressing process for different materials and projects. With its user-friendly control panel, you can easily set the desired temperature and time, ensuring precise and consistent results. The machine also includes a built-in safety mechanism that prevents overheating and ensures safe operation.

MUG -PRESS MACHINE INTRUDUCTION
CAUTION:
1. for continued protection against fire,disconnect power-supply before
using the machine,check the power-supply grounded connection well
before using.
2. disconnect power-supply before replacing different-function heat unit
3. put in the object going to be shaped,close up the pressure handle and
rotate the adjusting screw to get a proper pressure.
4. the surface of the heat unit is hot during heat pressing,do not touch them
with no proper protection.
BASIC PREPARATION BEFORE USING
1. plug the three-core power line into the outlet,check whether the power
supply is conformity with the rated voltage of the machine, there should be
a reliable ground wire for the power supply.
2. put in the object going to be shaped,close up the handle and rotate the
adjusting screw to get a proper pressure .
3. turn on the power switch, and the instrument board will display the
temperature .
4. set the temperature and time according to the table below and get the
specific corresponding temperature and timing setting.
initial temperature highest temperature time
single process 230 330 40
continuous process 325 330 120
Learn to set the temperature and time
1. press the mode key once, see the “set light” turning red. Press the plus or
minus key to set the initial heating temperature.
2. press the mode key for the second time, see the “temperature light” turning
red, Press the plus or minus key to set the highest heating temperature.
3. press the mode key for the third time, see the “time light” turning red, Prees
the plus or minus key to set the proper heating time.
4. press the mode key for the fourth time ,finish the setting and the machine
stands by to work.
Attention:
The initial heating temperature should be set between 200~380,the highest
heating temperature should be set between 200~430. the timing should be set
between 0~999 sec.
IF the initial heating temperature is 230, the highest heating temperature
should be set only between 230~430. as the same , IF the highest heating
temperature is 380, the initial heating temperature should be set only between
200~380.
initial heating temperature always =< highest heating temperature
OPERATION
Preset the corresponding temperature and timing for the object that is going to
be shaped. put into the object, close up the pressure handle, Press the
executive key, the temperature will straight to achieves the highest heating
temperature, wait for a few times(set), you will hear a hint sound ,the pressing
is finished, pull up the pressure handle,press the executive key. Do the next
object or turn off the power.
  • Page 1 1
  • Page 2 2

Karl home MA436OT11C23GNAFAMZ-4285423 Operating instructions

Karl home
Brand
Karl home
Model
MA436OT11C23GNAFAMZ-4285423
Type
Operating instructions
This manual is also suitable for

The Karl home MA436OT11C23GNAFAMZ-4285423 is a mug press machine designed to transfer designs onto mugs and other cylindrical objects. It features adjustable temperature and pressure settings, allowing you to customize the pressing process for different materials and projects. With its user-friendly control panel, you can easily set the desired temperature and time, ensuring precise and consistent results. The machine also includes a built-in safety mechanism that prevents overheating and ensures safe operation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents