BLISS™Automation by Alta
15 CHANNEL
REMOTE CONTROL
PROGRAMMING
AND USERS GUIDE
AMP25B
Instruction
Attention
-1-
The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades.
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Declarations
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
-2-
Safety
1. Do not expose motor to humid, damp or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.
Features
Fields of Application
Specifications
Following data for reference
Working temperature: -10℃ ~ +50℃
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.925MHz
Maximum Running Time: 6 minutes
Model Rated Torque
(N.m)
Rated Speed
(rpm)
Rated Power
(W)
AMP25B - 0.7/34 0.7 34 8
AMP25B -1.1/28 1.1 28 8
Charging Instructions
This motor has a built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .
During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and
needs to be charged.
During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped
running and needed to be recharged.
Rechargeable Battery
Blinking red:
Low battery alert
Blinking green:
Charging is processing
Solid green:
Battery has
finished charging.
FCC Text - text 01
Add A zoom in on the
charging port
P1 Button Instructions
P1 button
Lithium Battery Switch
LED light
Micro-USB Port
Add visual explanation of P1 - file 02
Sheer
Roller Revolve Roman shades
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
SAFETY INSTRUCTIONS
1. Do not expose motor to humid, damp, or extreme temperature
conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the power cable and antenna are clear and protected from
moving parts.
7. Cable routed through walls should be properly isolated.
8. Motor should be mounted in horizontal position only.
9. Before installation, remove unnecessary cords and disable equipment
not needed for powered operation.
Voltage 3V (CR2450)
Radio Frequency 433.92 MHz Bi-directional
Transmitting Power 10 milliwatt
Operating Temperature 14°F to 122°F (-10°C to 50°C)
RF Modulation FSK
Lock Function Yes
IP Rating IP20
Transmission Distance up to 200m (outdoor)
SPECIFICATIONS
Scan QR code to view additional BLISS™
Automation Programming Guides
Scan QR code to watch BLISS™ Automation
Programming Videos
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development
Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference
that may cause undesired operation of the device. Le présent appareil
est conforme aux CNR d’ISED applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil
doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
7. ADDING A REMOTE CONTROL
USING AN EXISTING
REMOTE CONTROL
a. On the current remote
control, press one “P2”
button until motor jogs x1
and beeps x1.
b. Once more, on the
current remote control,
press one “P2” button
until motor jogs x1 and
beeps x1.
c. On the New remote
control, press one “P2”
button until motor jogs x2
and beeps x3.
a. b.
c.
Jog x1
Jog x2
Jog x1
Beep x1
Beep x3
Beep x1
Current
Remote
Control
Action on
Remote
Control
Action on
Remote
Control
Motor
Response
Motor
Response
P2
P2
P2
PROGRAMMING A NEW REMOTE CONTROL
Follow instructions under the section 1. Pair / Unpair Remote Control
*Repeat the same procedure to add/remove additional remote control.
DECLARATIONS
GETTING STARTED - continued
Current
Remote
Control
NEW
Remote
Control
8. ADJUSTING THE MOTOR SPEED
INCREASE MOTOR
SPEED
a. Press one “P2” button
until motor
jog x1 and beep x1.
b. Press “Up” button until
motor jog x1 and beep x1.
c. Once more, press “Up”
button until motor jog x2
and beep x1.
DECREASE MOTOR
SPEED
a. Press one “P2” button
until motor jogs x1 and
beeps x1.
b. Press “Down” button
until motor jogs x1 and
beeps x1.
c. Once more, press
“Down” button until
motor jogs x2 and beeps
x1.
*If the motor has no response, it already has a Maximum or Minimum speed.
a.
a.
b.
b.
c.
c.
Jog x1
Jog x1 Jog x1
Jog x2
Jog x1
Jog x2
Beep x1
Beep x1 Beep x1
Beep x1
Beep x1
Beep x1
Up
Up
Down
Down
Action on
Remote
Control
Action on
Remote
Control
Action on
Remote
Control
Action on
Remote
Control
Motor
Response
Motor
Response
Motor
Response
Motor
Response
P2
P2
*If the motor has no response, it already has a Maximum or Minimum speed.
SETTINGS STEPS
1. Pairing P1 (hold for 2s) > Stop (hold for 2s)
2. Switch Rotating
Direction Up + Down (hold for 2s)
3. Set Upper/Lower
Limits
Upper Limit: Up (hold for 2s) >
Up + Stop (hold for 2s)
Lower Limit: Down (hold for 2s) >
Down + Stop (hold for 2s)
4.
Add/Remove
Favorite
Position
P2 > Stop > Stop
5. Roller/Sheer Mode
Switch Up + Down (hold for 5s) > Stop
6. Adjusting the
Limits
Upper: Up + Stop (hold for 5s) > Up or Dn > Up +
Stop (hold for 2s)
Lower: Dn + Stop (hold for 5s) > Up or Dn > Dn +
Stop (hold for 2s)
7. Add/Remove a
Remote P2 (existing) > P2 (existing) > P2 (new)
8. Speed Regulation
Increase Motor Speed: P2 > Up > Up
Decrease Motor Speed: P2 > Down > Down
QUICK INDEX
TROUBLESHOOTING
Cause
Battery in motor is depleted
Insucient charging from Solar
Panel
Remote control battery is discharged or
not installed properly
Radio interference / shielding
Receiver distance is too far
Power failure
Incorrect wiring
Cause
Battery voltage is low/ SolarPanel
Issue
Cause
Check if the motor in Sleep Mode
Multiple Motors are paired to the
same
Solution
Recharge with compatible AC adaptor
and check connection and positioning of
solar panel
Check connection and orientation of
solar panel
Replace battery or check placement.
Ensure remote control and the antenna
on the motor are positioned away from
metal objects
Move the remote control to a closer
position.
Check power supply to motor is
connected/active.
Check that wiring is connected correctly.
Solution
Recharge with AC adapter or check
connection and positioning of solar PV
panel
Solution
Press the P1 button on the motor for 2
seconds to activate Pairing Mode.
Always reserve a channel for
programming. To work on a single motor
at a time, place all other motorsinto sleep
mode. Press the “P1” button (about 6 ec)
on the motor head until motor jogs x2
and beeps x2.
PROBLEM - THE MOTOR BEEPS 10 TIMES WHEN IN USE
PROBLEM - THE MOTOR HAS NO RESPONSE
PROBLEM - THE MOTOR WILL NOT PROGRAM OR CONNECT
Revised 3/2022