Altair AMP25B User guide

Brand: Altair

Model: AMP25B

Type: User guide

Altair AMP25B is a rechargeable battery-powered motor designed for use with roller blinds, sheer shadings, roman shades, and zebra shades. It features a built-in Li-ion battery pack with integrated charge management and can be recharged using a standard 5V charger. The motor has a rated torque of 0.7/1.1 N.m, a rated speed of 34/28 rpm, and a rated power of 8W. It also has a built-in radio receiver and can be controlled using a remote control. The motor has safety features such as a low-voltage alarm, over-current protection, and a sleep mode to conserve battery power.

AMP25B

Instruction

Attention

-1-

The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades.

Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.

Important safety instructions to be read before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Declarations

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

-2-

Safety

1. Do not expose motor to humid, damp or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna and keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If power cable or connector is damaged, do not use.

6. Ensure correct crown and drive adaptor are used.

7. Ensure power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls shall be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not needed for powered

operation.

11. Installation and programming to be performed by a qualified professional, use or modification outside

the scope of this instruction may void warranty.

Features

Fields of Application

Specifications

Following data for reference

Working temperature: -10℃ ~ +50℃

Input Voltage: USB 5V 1A / USB 5V 2A

Radio Frequency: 433.925MHz

Maximum Running Time: 6 minutes

Model Rated Torque

(N.m)

Rated Speed

(rpm)

Rated Power

(W)

AMP25B - 0.7/34 0.7 34 8

AMP25B -1.1/28 1.1 28 8

Charging Instructions

This motor has a built in Li-ion battery pack with integrated charge management.

Max power input for recharging: 5V 2A.

Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .

During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and

needs to be charged.

During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped

running and needed to be recharged.

Rechargeable Battery

Blinking red:

Low battery alert

Blinking green:

Charging is processing

Solid green:

Battery has

finished charging.

FCC Text - text 01

Add A zoom in on the

charging port

P1 Button Instructions

P1 button

Lithium Battery Switch

LED light

Micro-USB Port

Add visual explanation of P1 - file 02

Sheer

Roller Revolve Roman shades

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

DECLARATIONS

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development

Canada licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired

operation of the device. Le présent appareil est conforme aux CNR d’ISED

applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d’en compromettre le fonctionnement.

Voltage 4.5V

Radio Frequency 433.92 MHz Bi-directional

Transmitting Power 10 milliwatt

Operating Temperature 14°F to 122°F (-10°C to 50°C)

RF Modulation FSK

Lock Function Yes

IP Rating IP20

Transmission Distance up to 200m (outdoor)

SPECIFICATIONS

SAFETY INSTRUCTIONS

1. Do not expose motor to humid, damp, or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna. Keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If the power cable or connector is damaged, do not use.

6. Ensure the correct crown and drive adaptor are used.

7. Ensure the power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls should be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not

needed for powered operation.

11. Installation and programming should be performed by a qualied professional.

Use or modication outside the scope of these instructions may void warranty.

Never drop, knock drill or submerge the motor, Read all safety instructions

before installation. Incorrect installation can lead to serious injury and will void

manufacturer’s liability and warranty.

Settings Steps

1 Pairing

TDBU Shades:

P1 (hold down for 2s) > Left Stop (hold down for 2s)

Regular Shades:

P1 (hold down for 2s) > Stop (hold down for 2s) Per Left / Right

you choose to pair

2 Switch Rotating Direction

TDBU Shades:

Left Up + Left Down (hold down for 2s)

Regular Shades:

Up + Down (hold down for 2s) Per Left / Right paired

3Setting Upper & Lower

Limits

TDBU Shades:

Upper Limit: Up (hold down for 2s) > Left Up + Left Stop (hold

down for 2s)

Lower Limit: Down (hold down for 2s) > Left Down + Left Stop

(hold down for 2s)

Regular Shades:

Upper Limit: Up (hold down for 2s) > Up + Stop (hold down for 2s)

Per Left / Right paired

Lower Limit: Down (hold down for 2s) > Down + Stop (hold down

for 2s) Per Left / Right paired

4Add / Remove Favorite

Position

TDBU Shades:

P2 > Left Stop > Left Stop

Regular Shades:

P2 > Stop > Stop Per Left / Right paired

5Roller Mode & Sheer

Mode Switch

TDBU Shades:

Left Up + Left Down (hold down for 5s) > Stop

Regular Shades:

Up + Down (hold down for 5s) > Stop Per Left / Right paired

6 Adjust Limits

TDBU Shades:

Upper Limit: Left Up + Left Stop (hold down for 5s) > Up or Down

> Left Up + Left Stop (hold down for 2s)

Lower Limit: Left Down + Left Stop (hold down for 5s) > Up or

Down > Left Down + Left Stop (hold down for 2s)

Regular Shades:

Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up +

Stop (hold down for 2s) Per Left / Right paired

Lower Limit: Down + Stop (hold down for 5s) > Up or Down >

Down + Stop (hold down for 2s) Per Left / Right paired

7Pair / Unpair Additional

Emitter

TDBU Shades:

P2 (existing) > P2 (existing) > P2 (new)

Regular Shades:

P2 (existing) > P2 (existing) > P2 (new) Per Left / Right paired

8 Speed Regulation

TDBU Shades:

Acceleration: P2 > Left Up > Left Up

Deceleration: P2 > Left Down > Left Down

Regular Shades:

Acceleration: P2 > Up > Up Per Left / Right paired

Deceleration: P2 > Down > Down Per Left / Right paired

QUICK INDEX

BLISS™Automation by Alta

TD/BU COMBINATION

REMOTE CONTROL

PROGRAMMING AND USERS GUIDE

Scan QR code to view additional BLISS™

Automation Programming Guides

Scan QR code to watch BLISS™ Automation

Programming Videos TROUBLESHOOTING

Problem - The motor has no response

Cause Solution

Battery in motor is depleted Recharge with compatible AC adaptor and check

connection and positioning of solar panel

Insucient charging from Solar Panel Check connection and orientation of solar panel.

Remote control battery is discharged Replace battery or check placement.

or not installed properly

Radio interference / shielding Ensure remote control and the antenna on the motor

are positioned away from metal objects.

Receiver distance is too far Move the remote control to a closer position.

Power failure Check power supply to motor is connected/active.

Incorrect wiring Check that wiring is connected correctly.

Problem - The Motor beeps 10 times when in use

Cause Solution

Battery voltage is low/ SolarPanel Issue Recharge with AC adapter or check connection and

positioning of solar PV panel

Problem - The Motor Will Not Program or Connect

Cause Solution

Check if the motor in Sleep Mode Press the P1 button on the motor for 2 seconds to

activate Pairing Mode.

Multiple Motors are paired to the same Always reserve a channel for programming. To work

Channel on a single motor at a time, place all other motors

into sleep mode. Press the “P1” button (about 6 ec)

on the motor head until motor jog x2 and beep x2.

To work on a single motor at a time, place all other motors into sleep mode by pressing the

P1 button (about 6 seconds) on the motor head until motor jogs X2 and beeps X2.

Rev 8/22

REPLACE/INSTALL BATTERIES

ADVANCED SETTING - DISABLE LIMIT SETTING

a. Remove the cover from the backside

of remote, the lock switch is in the

right corner.

b. Move the switch to the “Lock”

position to disable the following com-

mands, remote will show “L” (lock):

- Change Motor Direction

- Setting the Upper and Lower Limit

- Adjust Limit

- Roller Mode or Sheer Mode

c. Move the switch to “Unlock” posi-

tion to assess all remote functions,

remote will show “U” (unlock).

Switch

LockUnlock

*This advanced feature is intended to be

used after all shade programming is com-

pleted. User Mode will prevent accidental or

unintended changing of limits.

BUTTON INSTRUCTIONS

LCD Display

Right Up

Right Stop

Right Down

Right Side

P2 Button

Right Side

P2 Button

Switch

Higher

Channel

Higher

Channel

Lower

Channel

Lower

Channel

Left Up

Left Side

Controls

Bottom Rail

Left Side

Right Side

Controls

Middle Rail

Right Side

Left Stop

Left Down

Channel 1 - Channel 5 are for TDBU Shades

Channel 6 - Channel 16 are for regular shades. The right side and left side serve

the same function and can be considered as 2 individual channels.

Unused channels can be

hidden:

Channel 1 - 5: Channel 1 must

show

a. At CH 1 ~ CH 5, Press and

Hold (about 3 sec) “<” and “>”

buttons simultaneously until

remote control displays “t”

(TDBU).

b. Press “<” or “>” button

to select desired channel

(between 1 ~ 5).

c. Press “Stop” button to

conrm selection (the example

shows a 3-channel selection).

The LED will display “o” (OK)

once to conrm selection.

Channel 6-16: Channel 6

must show

a. At CH 6 ~ CH 16, Press and

Hold (about 3 sec) “<” and “>”

buttons simultaneously until

remote control displays “C”

(channel).

b. Press “<” or “>” button

to select desired channel

(between 6 ~ 16).

c. Press “Stop” button to

conrm selection (the example

shows a 5-channel selection:

CH6 ~ CH10). The LED will

display “o” (OK) once to

conrm selection.

Lower

Channel

Lower

Channel

Lower

Channel

Lower

Channel

Higher

Channel

Higher

Channel

Higher

Channel

Higher

Channel

Stop

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Remote

Response

Remote

Response

Remote

Response

Remote

Response

Remote

Response

Remote

Response

CHANNEL OPTIONS

Select A Channel

a. Press “<” button on the

remote to select a lower

channel.

b. Press “>” button on the

remote to select a higher

channel.

Channel 1 - Channel 5 are for TDBU Honeycomb

Channel 6 - Channel 16 are for Standard or Tilt-Only shades

Channel 0 - Controls all shades

a. b.

Higher

Channel

Lower

Channel

Action on

Remote

Control

Remote

Response

P1 Button

LED

light

P1 button

Lithium Battery Switch

Power line

Signal line

P1 Button

HIDE UNUSED CHANNELS

click

a. Gently apply a small amount

of pressure to the cover and slide

the cover o.

b. Install 2 AAA batteries into

the battery compartment making

sure the polarity matches the

markings.

c. Gently slide the cover back on

until a “click” sound is heard.

LockUnlock

P1 BUTTON LOCATION

HORIZONTAL

BLIND

TILT MOTOR

ROLLER / SHEER

DUAL / WOVEN

MOTOR

HONEYCOMB

STANDARD SHADE

MOTOR

HONEYCOMB

TOP-DOWN/BOTTOM-UP

SHADE MOTOR (TDBU)

Left Side

P2 Button

Back Side

of Remote

Back Side

of Remote

Battery

Cover

Battery

Cover

Blinking Red:

Low battery alert

Blinking Green:

Charging in process

Solid Green:

Finished charging

Internal Rechargeable Battery

During operation, if the motor begins to beep, this is an indicator to let users

know the motor power is low and needs to be charged. To charge, plug the

micro-USB port on the motor into the 5V/2A charger.

Solid Green:

Finished charging

Solid Red:

Charging in process

External Rechargeable Battery Pack

During operation, if the voltage is detected to be too low, the battery stops

running and needs to be recharged. To charge, plug the micro-USB port on

the end of the battery pack into the 5V/2A charger.

MOTOR CHARGING AND BATTERY STATUS INDICATORS

Switch

Left Side

P2 Button

click

8. ADJUST MOTOR SPEED

6. ROLLER MODE

7. ADD OR REMOVE ADDITIONAL REMOTE

4. ADJUST LIMITS

3. SETTING THE UPPER AND LOWER LIMITS

4.1 Adjust the Upper Limit

a. Press and hold (about 5 sec)

Left “Up” and Left “Stop”

buttons simultaneously until

the motor jogs x1.

b. Press Right “Up” button

to raise the Middle Rail, then

press Right “Stop” button

when it is in the new desired

upper limit.

c. Press Left “Up” button to

raise the Bottom Rail, then

press Left “Stop” button

when it is in the new desired

upper limit.

6.1 Roller Shade Mode -

continue movement after a

short press - Default Mode

a. Press and hold (about 5 sec)

Left “Up” and Left “Down”

buttons simultaneously until the

motor jogs x1.

b. Press and hold (about 2 sec)

Left “Stop” button until the

motor jogs x2.

7.1 Using Current Remote

Control

a. On the current remote

control, press Left Side “P2”

button until the motor jogs x1.

b. Once more, on the current

remote control, press Left Side

“P2” button until the motor

jogs x1.

c. On the Additional remote

control, press Left Side “P2”

button until the motor jogs x2.

8.1 Acceleration Speed

a. Press Left Side “P2” button

until the motor jogs x1.

b. Press Left “Up” button until

the motor jogs x1.

c. Once more, press Left “Up”

button until the motor jogs x2.

8.2 Decelaration Speed

a. Press Left Side “P2” button

until motor

jog x1.

b. Press Left “Down” button

until the motor jogs x1.

c. Once more, press Left

“Down” button until the

motor jogs x2.

4.2 Adjust the Lower Limit

a. Press and hold (about 5 sec)

Left “Down” and Left “Stop”

buttons simultaneously until

the motor jogs x1.

b. Use Left “Down” button

to lower the Bottom Rail then

press Left “Stop” button

when it is in the new desired

lower limit.

c. Press Right “Down” button

to lower the Middle Rail, then

press Right “Stop” button

when it is in the new desired

lower limit.

*If the motor has no response,

it already has a Maximum or

Minimum speed.

3.1 Set Upper Limit

a. Press Right “Up” button

to raise the Middle Rail, then

press Right “Stop” button

when it is in the desired upper

limit.

b. Press Left “Up” button to

raise the Bottom Rail, then

press Left “Stop” button when

it is in the desired upper limit.

c. Press and hold (about 2 sec)

Left “Up” and Left “Stop”

buttons simultaneously until

the motor jogs x2.

*If you exit the limit setting status before you nish the

limit settings, the motor will take the previous existing

limits.

3.2 Set Lower Limit

a. Press Left “Down” button

to lower the Bottom Rail, then

press Left “Stop” button when

it is in the desired lower limit.

b. Press Right “Down” button

to lower the Middle Rail, then

press Right “Stop” button

when it is in the desired lower

limit.

c. Press and hold (about 2 sec)

Left “Down” and Left “Stop”

buttons simultaneously until

the motor jogs x2.

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Middle Rail

Response

Motor Response

Bottom Rail

Response

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Motor Response

Bottom Rail

Response

Middle Rail

Response

Jog x1

Left

Down

Left

Stop

Jog x2

Left Up

Right Up Left Up

Left Stop

a. b.

Left Down

Jog x1

Jog x2

Left Up Left

Down

Left

Stop

Action on

Remote

Control

Action on

Remote Control

Motor Response

Jog x1

Jog x2

Jog x1

Current Remote

Control

New Remote Control

Current Remote

Control

Action on

Remote Control

Action on

Remote Control

Motor Response

Jog x1

Jog x1 Jog x1

Jog x2

Jog x1

Jog x2

Left Up

Left Down

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Motor Response

7.2 New Remote Control

Follow instructions under the section 1. Pair / Unpair Remote Control

*Repeat the same procedure to

remove additional remote control.

Action on

Remote

Control

Motor Response Jog x2

Left

Down

Left

Stop

Right Down

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Motor Response

Middle Rail

Response

Bottom Rail

Response

Jog x1

Left Up Left Stop

Right Up

Action on

Remote

Control

Motor Response Jog x2

Left Up Left

Stop

Left Up

d. Press and hold (about 2 sec) Left “Up” and Left

“Stop” buttons simultaneously until the motor

jogs x2.

d. Press and hold (about 2 sec) Left “Down” and Left

“Stop buttons simultaneously until the motor jogs x2.

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Bottom Rail

Response

Motor Response

Middle Rail

Response

Jog x2

Left Down

Left

Down

Right

Down

Left Stop

a. b.

2. CHANGE MOTOR DIRECTION (IF NECESSARY)

1. PAIR / UNPAIR REMOTE CONTROL

CHANNELS 1 -5 PROGRAMMING GUIDE FOR TDBU SHADES

All setup needs to be done using LEFT SIDE of the remote.

Jog x1

Jog x2

GETTING STARTED

It is important to conm that the motor is awake and ready to receive

programming. To do this, press “P1” button on the motor less than 1 sec, to

activate the motor from Sleep Mode.

a. Press “P1” button (about 2

sec) on the End Cap as shown

until the motor jogs x1.

b. In the next 10 secs, press

and hold Left “Stop” button

on the remote control until the

motor jogs x2.

Press Left “Up” or Left

“Down” button to check if the

shade moves in the desired

direction.

If you need to reverse the di-

rection, press and hold (about

2 sec) Left “Up” and “Down”

buttons simultaneously until

motor jog x1.

*The operation is only valid when there are no set limits.

* Repeat the same procedure to

unpair remote control.

Action on

Motor

Action on

Remote

Control

Action on

Remote Control

Motor Response

Left Up Left

Down

Left Stop

Honeycomb TDBU

NOTE: If you are programming any product other

than a Honeycomb Top-Down/Bottom-Up shade,

please proceed to the programming section for

Channels 6-16 Standard Shades

5. FAVORITE POSITION

5.1 Set Favorite Position

a. Use Left “Up” and “Down”

buttons to move the bottomrail

to the desired Favorite position.

Use Right “Up” and “Down”

buttons to move the middle rail

to the desired Favorite position.

b. Press one of the “P2” buttons

on the back of remote control

until the motor jogs x1.

c. Press and hold the Left

“Stop” button until the motor

jogs x1.

5.3 Delete Favorite Position

a. Press one of the “P2”

buttons on the back of the

remote, the shade will jog X1.

b. Press and hold (about 2 sec)

Left “Stop” button until the

motor jogs X1.

c. Once more, press and hold

(about 2 sec) Left “Stop”

button until the motor jogs x2.

5.2 Send Shade to Favorite Position

Press and hold the Left “Stop” button

until the shade moves. The rails will

move to Favorite position.

d. Once more, press and hold the Left “Stop”

button until the motor jogs x2.

Jog x1

Jog x1 Jog x1

Jog x1

Left Up/

Down

Left

Stop

Left Stop

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Action on

Remote

Control

Motor

Response

Shade Response

Motor Response

c. d.

Jog x1 Jog x2

Left

Stop

Left

Stop

Action on

Remote

Control

Motor Response

Right Up/

Down

GETTING STARTED

It is important to conm that the motor is awake and ready to receive

programming. To do this, press “P1” button on the motor less than 1 sec, to

activate the motor from Sleep Mode.

Beep x1

Beep x3

Beep x1

Beep x3

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

CHANNELS 6 -16 PROGRAMMING GUIDE FOR STANDARD OR TILT-ONLY

SHADES, LEFT SIDE AND RIGHT SIDE SERVE THE SAME FUNCTIONS.

NOTE: BLISS LIFT and BLISS TILT motors DO NOT BEEP.

8. ADJUST MOTOR SPEED

6. ROLLER MODE AND SHEER MODE

7. ADD OR REMOVE ADDITIONAL REMOTE

5. FAVORITE POSITION

2. CHANGE MOTOR DIRECTION (IF NECESSARY)

3. SETTING THE UPPER AND LOWER LIMITS

4. ADJUST LIMITS

1. PAIR / UNPAIR REMOTE CONTROL

Jog x1

Jog x2

Beep x1

Beep x3

a. Press “P1” button (about 2

sec) on the motor head until

motor jogs x1 and beeps x1.

b. In the next 10 secs, press

and hold “Stop” button on the

remote control until motor

jogs x2 and beeps x3.

4.1 Adjust the Upper Limit

a. Press and hold (about 5

sec) “Up” and “Stop” buttons

simultaneously until motor jogs

x1 and beeps x1.

b. Use “Up” button to raise the

shade to the desired highest

position, and use “Up” or

“Down” button to do the nal

adjustment if necessary.

6.1 Roller Shade Mode - continue

movement after a short press -

Default Mode

a. Press and hold (about 5 sec) “Up”

and “Down” buttons simultaneously

until motor jogs x1.

7.1 Using Current Remote

Control

a. On the current remote

control, press Left or Right

“P2” button (per Left/Right

paired) until motor jog x1 and

beep x1.

b. Once more, on the current

remote control, press Left or

Right “P2” button (per Left/

Right paired) until motor jog

x1 and beep x1.

8.1 Acceleration Speed

a. Press Left or Right “P2”

button (per Left/Right paired)

until motor jog x1 and beep x1.

b. Press “Up” button until

motor jog x1 and beep x1.

c. Once more, press “Up”

button until motor jog x2 and

beep x1.

6.2 Sheer Shade Mode - jog

movement after a short press

(continue movement after a long

press)

a. Press and hold (about 5 sec) “Up”

and “Down” buttons simultaneously

until motor jogs x1.

8.2 Deceleration Speed

a. Press Left or Right “P2”

button (per Left/Right paired)

until motor jog x1 and beep x1.

b. Press “Down” button until

motor jogs x1 and beeps x1.

c. Once more, press “Down”

button until motor jogs x2 and

beeps x1.

5.1 Set Favorite Position

a. Use “Up” or “Down” button

to move the shade to desired

Favorite position.

b. Press Left or Right “P2”

button (per Left/Right paired) on

the back of remote control until

motor jogs x1 and beeps x1.

c. Press “Stop” button until

motor jogs x1 and beeps x1.

d. Once more, “Stop” button

until motor jogs x2 and beeps x3.

5.3 Delete Favorite Position

a. Press Left or Right “P2”

button (per Left/Right paired)

until motor jogs and beeps x1.

b. Press “Stop” button until

motor jogs and beeps x1.

c. Once more, “Stop” button

until motor jogs x1 and long

beep x1.

4.2 Adjust the Lower Limit

a. Press and hold (about 5 sec)

“Down” and “Stop” buttons

simultaneously until motor jogs

x1 and beeps x1.

b. Use “Down” button to lower

the shade to the desired lowest

position, and use “Up” or

“Down” button to do the nal

adjustment if necessary.

5.2 Send Shade to Favorite

Position

Press and hold (about 2 sec)

“Stop” button, motor will

move to Favorite position.

Press “Up” or “Down” button

to check if the shade moves in

the desired direction.

If you need to reverse the di-

rection, press and hold (about

2 sec) “Up” and “Down”

buttons simultaneously until

motor jogs x1 and beeps x1.

3.1 Set Upper Limit

a. Press “Up” button to raise

the shade, then press “Stop”

button when it is in the desired

upper limit.

b. Press and hold (about 5

sec) “Up” and “Stop” buttons

simultaneously until motor

jogs x2 and beeps x3.

*The operation is only valid when there are no limits. If the motor has already set the upper

and lower limit, then you can only switch direction by pressing “P1” button (about 10 sec) on

the motor head until motor jog x3 and beep x3.

* Repeat the same procedure to unpair remote control.

*If you exit the limit setting status before you

nish the limit settings, the motor will take the

previous existing limits.

NOTE: If the motor

has no response,

it already has

a Maximum or

Minimum speed.

3.2 Set Lower Limit

a. Press “Down” button to

lower the shade, then press

“Stop” button when it is in the

desired lower limit.

b. Press and hold (about 5 sec)

“Down” and “Stop” buttons

simultaneously until motor

jogs x2 and beeps x3.

Action on

Motor

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Motor Response

Up Down

Stop

a. b.

Jog x2

Down Stop

Stop

Down

Jog x1

Jog x2

Beep x1

Beep x3

Stop

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Motor Response

Stop

Jog x1 Beep x1

Down Stop Down

Jog x2 Beep x3

Down Stop

Jog x1

Jog x2

Up Down

Stop

Motor Response

Jog x1

Jog x1 Beep x1

Action on

Remote Control

Motor Response

Up Down

Stop

Jog x1

Jog x2

Jog x1

Beep x1

Beep x3

Beep x1

Current Remote

Control

New Remote Control

Current Remote

Control

Action on

Remote Control

Action on

Remote Control

Motor Response

P2 P2

Jog x1

Jog x1 Jog x1

Jog x2

Jog x1

Jog x2

Beep x1

Beep x1 Beep x1

Beep x1

Down

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Motor Response

7.2 New Remote Control

Follow instructions under the section 1. Pair / Unpair Remote Control

NOTE: Repeat the

same procedure to

remove additional

remote controls.

Factory Mode Complete

User Mode Begins

Jog x1

Jog x1 Jog x2

Beep x1

Jog x1 Jog x1

Jog x1

Beep x1 Beep x1

Up Down

Stop

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Action on

Remote Control

Motor Response

Shade Response

Motor Response

Roller Standard

Honeycomb

Sheer Banded Tilt-Only

Horizontal

Natural

Woven

c. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until

motor jogs x2 and beeps x3.

c. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until

motor jogs x2 and beeps x3. P2

b. Press and hold (about 2 sec) “Stop” button until motor jogs x2 and beeps x3.

b. Press and hold (about 2 sec) “Stop” button until motor jogs x1 and beeps x1.

c. On the Additional remote control, press Left or Right “P2” button (per Left/

Right channel you would like to pair) until motor jogs x2 and beeps x3.

NOTE: If you are programming a Honeycomb Top-Down/Bottom-Up

shade, please proceed to the programming section for Channels 1-5.

Altair AMP25B User guide

Altair AMP25B User guide

Other documents