PRODUCT SHEET
GB
The No-Frost system ensures the cool air freely circulates
around the stored food, reduces humidity and prevents ice
build-up, thus, entirely eliminating the need of
compartments defrosting. Frozen products do not stick
together, the labels remain clear, and the food storage
space stays clean. The forced airflow No-Frost system
assures even temperature distribution inside the
compartments and helps to keep the food fresh longer.
A. Refrigerator Compartment
1.
Crisper
2.
Shelves
3.
No-Frost system
3a.
Cold air vents
4.
Lighting module
5.
Cooler compartment
6.
Rating plate
7.
Door trays
8.
Removable shelf with a bottle holder
9.
Lower shelf (depending on the model)
B. Freezer Compartment
10.
Turntable with an ice-cube tray (depending on the model)
11.
Ice-cube tray (depending on the model)
12.
Super Fast Freezing (SFF) Compartment
13.
The freezer door trays for pizza or other frozen products
with a short storage time (depending on the model)
C. Control panel
D) Anti-bacterial filter (depending on the model)
Note:
•
The internal temperatures of the appliance
depend on
the ambient temperature, frequency of opening the doors,
as well as location of the appliance. Adjust the thermostat
knob depending on these factors.
•
The number and type of shelves,
as well as configuration
of accessories may vary, depending on model. All shelves
and door trays are removable.
•
The appliance accessories
are not suitable for washing in
a dishwasher.
The
anti-bacterial filter
ensures a higher level of hygiene in
your refrigerator through continuous purifying of circulating
air from bacteria. Remove it from the box (found in the
crisper drawer (item 1) and insert into the grille (item D).
Replace the filter every 6 months.
1.
Remove the filter together with the grille and dispose as a
whole.
2.
Replace the filter and the grille with the new ones.
3.
The replacement procedure is attached with the filter.
Our After-sales Service can supply this type of filter.
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, the
refrigerator
and freezer compartment
starts operation automatically.
Specific control elements are activated:
•
The indicator lamps on the control panels light up for 2
seconds.
•
The alarm becomes activated for 1 second.
Note:
•
Food products put inside the appliance before it
achieved its set operating temperature may spoil.
OPERATION DESCRIPTION
Adjustment Temperature:
•
To adjust the temperature in the
refrigerator compartment, turn the knob inside the
refrigerator compartment above the lighting module:
- To set a lower temperature, turn the knob to its leftmost
position.
- To set a higher temperature, turn the knob to its rightmost
position.
It is recommend to set the thermostat to position 3-4.
To adjust the temperature in the freezer compartment
,
use the temperature selection function.
•
Temperature is selected by consecutive pressing of the
button:
- Minimum
- Medium
- Maximum
•
The appropriate of the green indicator lamps (under the
asterisks) on the control panel is on.
•
The temperature of the freezer compartment is factory set
at the medium position. The middle green indicator lamp on
the control panel is on.
•
When the appliance is disconnected from power supply and
then re-connected, the freezer remembers the previously
set temperature.
CONTROL PANEL DESCRIPTION
On/Off buttons
1.
Alarm deactivating button: “
RESET
”.
2.
Yellow indicator light informing of an alarm: “
Black Out
”
and/or “
Anti-Bacterial Filter
” replacement.
3.
“
Fast Freezing
” button.
4.
Green lamps indicating the “
Freezer Temperature
”.
5.
Temperature selection button “
-/+
”.
How to replace the bulb
1.
Bulb cover.
2.
Light bulb
3.
Notches for removing
the cover.
Before replacing the light bulb, make sure to disconnect the
appliance from the mains power supply. Following this:
•
Remove the fan cover by grasping the notches (3), bend
aside and pulling outwards.
•
Remove the bulb by pulling it out (the bulb is of a special
push-in type - do not rotate the bulb).
•
Check the bulb and replace it, if necessary, with a new one:
Push the bulb into the fitting till it stops.
•
Snap the cover back on.
Notes:
•
Do not leave the bulb uncovered.
•
The bulb must not exceed 15W.
•
It is available via our After-Sales Service outlets only
GUIDE TO SELECTING FUNCTIONS
Functions and settings
Other abnormal appliance operations displayed
by indicator lamps.
In case of abnormal appliance operation, all the temperature
selection indicator lamps will flash and a beep will sound.
After pressing and holding the alarm deactivation "
RESET
"
button, the beep will stop and the indicator lamps will light
up, allowing for determining the alarm code (in accordance
with the following table listing possible alarm codes).
When the "
RESET
" is released, the indicator lamps will flash
until the fault is eliminated. If any alarm from the table below
occurs, other functions such as temperature adjustment and
fast freezing are not available until the fault is eliminated.
When several alarms occur simultaneously, the alarm with the
highest priority is displayed. (Code 01 is the highest priority.)
After determining the alarm code (between 01 and 04):
•
The user can eliminate the reason of the code 04 alarm by
closing the door completely.
•
Code 03 alarm - The alarm deactivates when the minimum
required temperature is reached.
•
The other alarms (code 01, 02) - Contact the After-Sales
Service and provide the alarm code.
How can increase the freezer compartment capacity
In certain models you can increase the freezer compartment
capacity by:
- Removing the shelf with the turntable.
- Removing the turntable only.
Please refer to the figures beside to see how to proceed.
How to make ice cubes
Depending on the model:
With a turntable and ice-cube trays
•
Remove the turntable, fill the trays with water to approx. 3/
4 and place back in the appliance.
•
The ice-cubes will be automatically ejected into the
container after turning the ice-cube tray knobs
With an ice-cube tray
•
Fill the ice-cube tray with water to approx. 3/4 and insert it
into the SFF section of the freezer compartment.
•
Do not use any sharp or cutting items to remove the tray.
Alarm off button
Fast Freezing
: Activate this function before freezing
fresh products. To activate this function, press the
“
Fast Freezing
”
- All 3 green indicator lamps on the panel will light
up simultaneously. This function is automatically
disabled after 18 hours. To deactivate it earlier:
- Press the “
Fast Freezing
” button again - the
temperature selection indicator lamps will return
to the previously set temperature level, or.
- Press the temperature selection button in the
freezer compartment.
Temperature selection - It is possible to select
between 3 levels of the freezer temperature
(minimum, medium, maximum) by
pressing the temperature selection button .
The “
Anti-Bacterial Filter
” - alarm, signalled by the
continuous yellow indicator lamp (2), indicates the
need to replace the filter. After replacing the filter
press the “
RESET
” button for approx. 5
seconds until the indicator lamp goes off.
“
Black-out
”
Alarm -
in case of power failure, the
appliance automatically monitors the temperature
changes in the freezer compartment. After the
power supply returns,- the
“Black-out”
alarm will
activate, if the temperature has risen above the
admissible level. This is indicated by:
- Flashing of the yellow indicator lamp (2).
- Activation of a beep.
When the “
Black-out
” alarm is active, it is
recommended to proceed as follows:
- If the food in the freezer is not frozen but is still
cold, transfer it promptly to the refrigerator
compartment and consume within 24 hours.
- If the food in the freezer is frozen, it has re-frozen
after thawing caused by the power failure.
Consumption of re-frozen food is not
recommended since it lost its nutritive value and
may be hazardous to your health.
Note:
The “
Black-out
” alarm does not guarantee
the food quality and its safety in case of consumption.
It merely indicates the necessity to assess the quality
of food in the freezer andrefrigerator compartments.
To deactivate the alarm, press the “
RESET
”
button for approximately 3 seconds, until the
indicator light goes off.
The temperature will return to the normal operating
cycle level and the beep will silence.
Alarm priority Alarm
code
Te m p e r a t u r e
setting indicator lamps on
minimum
MIN
medium
MED
maximum
MAX
Evaporator sensor failure 01 No
Yes
No
Freezer sensor failure 02
Yes
No No
High freezer compartment
temperature alarm
03
Yes Yes
No
Open door alarm 04
Yes Yes Yes
5019 636 01001
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool ARC 5603 Program Chart
-
LADEN DC 191 Program Chart
-
Whirlpool ARC 2150W Program Chart
-
Whirlpool ARC 6670 Program Chart
-
Whirlpool KDN 4382 A2+ PT User guide
-
Whirlpool ART 480/A++ Program Chart
-
Whirlpool ARC 4188/IX/A+ User guide
-
Whirlpool WTC 3746 A+NFCX Program Chart
-
Whirlpool CFS 710 S GB User guide
-
Whirlpool ARC7637 IX Program Chart
Other documents
-
Bauknecht KGEA 320 BIO OPTIM. Program Chart
-
Bauknecht KGA325 PUREOPTIMA/1 WS Program Chart
-
KitchenAid KRCB 6064 Program Chart
-
Bauknecht KGN PLATINUM 32 IN Program Chart
-
Bauknecht KGA 355 BIO OPTIM. Program Chart
-
Bauknecht KGA 285 PURE OPTIMA IO Program Chart
-
-
Bauknecht KGA355 BIO OPTIMA/1 WS Program Chart
-
-
Bauknecht KGE PLATINUM3 A++IO Program Chart