Anova LEX1640S Assembly Instruction

Type
Assembly Instruction
1
anovafurnishings.com
888.535.5005 tel
Rubber Foot
1/4” -20 x 1”
Phillips Head Screw
(2) Adhesive
Strips
Plastic
Rectangular
Foot
Packing cardboard or
other soft work surface
ASSEMBLY INSTRUCTIONS
LEX1640S - Exposition 4-Seat Table w/ Contour Swivel Seat
TOOLS NEEDED:
Ratchet with 7/16”, 1/2” and 9/16” sockets
1/2” Open end or box end wrench
9/16” Open end or box end wrench
5/32” Allen wrench
#4 Phillips screwdriver
TABLE COMPONENTS:
ASSEMBLY HARDWARE: All hardware is stainless steel.
(1) Table Top
(2) Seat Supports
The assembly is a two-person operation.
1. Inspect the shipping container contents for damage and to
determine that all components and hardware are present.
2. Assemble the table over the shipping packaging or padded
work area to avoid scratching the product.
NOTE: Before assembling the nuts to the bolts, it is
recommended that a light oil or petroleum jelly be applied to the
screw threads.
3. Locate the two seat supports and place the supports on the work
surface upside down with the seat platforms oriented downward.
4.
Apply two adhesive strips to one of the plastic rectangular feet. Then
firmly apply the plastic rectangular foot to the metal foot of the seat
supports aligning the holes in each. Repeat for the remaining feet.
Seat Support
(4) Contour Seats
(1) Table Top Bracket
(4) Seat Mounts
(4) 5/16” x 1 1/4”
Hex Head Bolts
(32) 1/4”-20 x 3/4”
Socket Head Cap
Screws
(16) 5/16” x 1 1/4”
Phillips Head Screws
(32) 1/4”
Nylock Nuts
(24) 5/16”
Flat Washers
(20) 5/16”
Nylock Nuts
(6) Rubber Feet
(6) 1/4” -20 x 1”
Phillips Head
Screws
(8) Adhesive Strips
(4) Plastic
Rectangular
Feet
(64) 1/4
Flat Washers
(4) Swivels
(16) 3/8“
Flat Washers
(8) 3/8
Nylock Nuts
(8) 3/8” x 1 1/4”
Hex Head Bolts
2
5. Locate the rubber feet and 1/4” -20 x 1” Phillips head
screws. Insert a screw through the rubber foot into the
pre-drilled hole in the seat support and tighten screw with
the #4 Phillips screwdriver. Once all six rubber feet are
installed turn the support over so that the feet are
contacting the work surface.
Seat Support
Packing cardboard or
other soft work surface
Seat Platforms
3/8” Flat Washers
3/8” Nylock Nuts
Table Top Bracket
6. Locate the table top bracket. Position the bracket at
the end of the seat support so that the extended supports
are out to the sides and parallel to the main shaft of the seat
support. Bracket needs to be angled upward.
Place 3/8” flat washers on four 3/8” x 1 1/4” hex head
bolts and insert the bolts through the four mounting
holes in the seat support end plate and into the
matching holes in the table top bracket. Place 3/8” flat
washers and 3/8” Nylock nuts on the end of the bolts
and finger tighten.
Attach the other seat support to the opposite side of
the table top bracket in the same manner.
After all the bolts are installed, use the 9/16” open end
or box end wrench and ratchet with 9/16” socket
to tighten.
3/8” Flat Washers
3/8” x 1 1/4”
Hex Head Bolt
3/8” Nylock Nut
3/8” Flat Washers
Table Top Bracket
3/8” Flat Washers
3/8” x 1 1/4” Hex Head
3
7.
Locate one of the seat swivels. Position the seat swivel on one of
the seat platforms so that the mounting holes in the seat swivel
align with the mounting holes in the seat platform.
NOTE: The word “Front” is stamped into the frame of the swivel.
This should be oriented toward the center of the table.
Place 1/4” flat washers on four 1/4”-20 x 3/4” socket head cap
screws and insert the screws through the bottom plate of the
swivel and the support mounting plate. Place 1/4” flat washers and
1/4” Nylock nuts on the end of the screws and finger tighten.
Install the remaining seat swivels in the same manner.
After all bolts are installed, tighten using the 7/16” socket and
5/32” Allen wrench.
Note: The screw heads must be inside the swivel and the Nylock
nuts must be outside of the swivel for the swivel to work properly.
1/4”-20 x 3/4” Socket
Head Cap Screw
Swivel
1/4” Flat Washer
1/4” Nylock Nut
1/4” Flat Washer
Seat Platform
8.
Locate one of the seat mounts. Position the seat mount on
one of the seat swivel/seat supports so that the mounting
holes in the seat mount align with the mounting holes in the
top plate of the seat swivel.
Place 1/4” washers on four 1/4”-20 x 3/4” socket head cap
screws and insert the screws through the top plate of the
seat swivel and the seat mount. Place 1/4” flat washers and
1/4” Nylock nuts on the end of the screws and finger tighten.
Install the remaining seat mounts in the same manner.
After all the screws are installed, tighten using the 7/16”
socket and 5/32” Allen wrench.
Note: The screw heads must be inside the swivel and the
Nylock nuts must be outside of the swivel for the swivel to
work properly.
1/4” Nylock Nut
1/4”-20 x 3/4”
Socket Head Cap
1/4” Flat Washer
1/4” Flat Washer
Seat Mount
5/16” Flat Washer
5/16” Nylock Nut
5/16” x 1 1/4”
Phillips Head Screw
Contour Seat
9. Place one of the seats over one of the seat mounts so
that all the mounting holes line up.
Insert four 5/16” x 1 1/4” Phillips head screws through the
seat mounting holes into corresponding holes in the seat
mount. Place 5/16” flat washers and 5/16” Nylock nuts on the
end of the screws and finger tighten. Install the remaining
seats in the same manner.
After all the screws are installed, tighten using the #4 Phillips
screwdriver and a 1/2” socket.
Note: The screw heads must be inside the swivel and the
Nylock nuts must be outside of the swivel for the swivel to
work properly.
4
02/10/2020 Copyright 2020 ANOVA® Manufactured in the U.S.
10.
Lift the table top and position it over the table top bracket. Rotate the table top until the frame on the bottom of the table top matches the
orientation of the table top bracket. Carefully lower the table top down onto the table top bracket.
Secure the table top to the table top bracket using 5/16” flat washers on four 5/16” x 1 1/4” hex head bolts. Insert the bolts with washers from
inside the bracket and place 5/16” flat washers and 5/16” Nylock nuts on the end of the bolts at the outside of the table top frame. You may have
to lift the table top slightly to get the holes to align.
Leave the bolts finger tight until all are started, then use the 1/2” open end or box end wrench and ratchet with 1/2” socket to tighten.
11.
Move the table to the location where it will be used.
NOTE: This table is required to be surface mounted prior to use. Follow surface mount instructions provided with the surface mount hardware that
you purchase locally.
12. After two weeks, retighten all of the hardware.
Table Top
5/16” Flat Washer
5/16” Nylock Nut
5/16” Flat Washer
5/16”-1 1/4” Hex Head Bolt
Table Top Bracket
NOTE: Please contact Customer Care at 1-866-797-1761 to receive assistance in placing a replacement part order.
(1) Table Top
(1) Table Top Bracket
(4) Contour Seats
(2) Seat Supports
(4) Seat Mounts
(4) Swivels
Replacement Parts
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Anova LEX1640S Assembly Instruction

Type
Assembly Instruction

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI