Anova BH1831R Assembly Instruction

Brand: Anova

Model: BH1831R

Category: Computer desks

Type: Assembly Instruction

This manual is also suitable for

anovafurnishings.com

888.535.5005 tel

TOOLS NEEDED:

• Ratchet with 1/2” socket

• 1/2” Open end or box end wrench

• 5/32” Allen wrench

• Rubber mallet

Assembly Instructions

Beacon Hill 3-Seat ADA Tables with Flat or Contour Seats

BH1830R– Recycled Plastic with Contour Seats

BH1830R-GT - Recycled Plastic ADA Game Table, 3 Seats

BH1831R– Recycled Plastic with Flat Seats

BH1831R-GT - Recycled Plastic ADA Game Table, 3 Flat Seats

BH1830T– Thermory® with Contour Seats

BH1830T-GT - Thermory® ADA Game Table, 3 Seats

BH1831T– Thermory® with Flat Seats

BH1831T-GT - Thermory® ADA Game Table, 3 at Seats

COMPONENT PARTS:

ASSEMBLY HARDWARE: All hardware is stainless steel.

ASSEMBLY:

Recycled Plastic with Contour

Seats

Thermory with Flat Seats

Inspect the shipping container contents for damage and to

determine that all components and hardware are present.

2. Lay all parts on a so work surface or on the shipping

packaging to prevent damage to nish.

3. Open the hardware package and nd the three black

plastic plugs. Insert a plug in the hole on the bottom of

each of the seat supports. Use the rubber mallet to seat the

plugs.

NOTE: Before assembling the nuts to the bolts, it is

recommended that a light oil or petroleum jelly be applied

to the screw threads.

The assembly is a two-person operation

4. Locate two seat supports and the lower

leg bracket. Position the seat supports

so that they will be opposite each other

when fastened to the lower leg bracket.

Install 5/16” at washers on 5/16” x

1” hex head bolts and insert the bolts

through the appropriate mounting

holes in the lower leg bracket and into

the lower mounting holes in the seat

supports. Place 5/16” at washers and

5/16” Nylock nuts on the end of the bolts

and tighten nger tight.

5. Position the remaining seat support

so that it aligns with the remaining

mounting hole in the lower leg bracket.

Attach the seat support to the lower

leg bracket using a 5/16” x 1” hex head

bolt with 5/16” at washers on the top

and bottom and a 5/16” Nylock nut to

secure. Leave the hardware nger tight

until aer the table top pan is secured

(step 7).

6. Locate the table top pan and place it on top of the platform created by the raised end of the seat supports. Adjust the placement of the table

top pan until one set of mounting holes in the pan aligns with the corresponding set of mounting holes in one of the seat supports.

Place a 5/16” at washer on the end of one of the 5/16” x 1” hex head bolts and insert the bolt through the pan mounting hole in the inner

bolt circle and through the hole in the support. Fasten the bolt using a 5/16” at washer and a 5/16” Nylock nut on the bottom of the bolt.

Leave the bolt and nut nger tight. Repeat this for the remaining two 5/16” hex head bolts. You may have to adjust the seat supports or the

table top pan in order to get the mounting holes to align.

7. Place a 1/4” at washer on the end of one of the 1/4” x 1 1/2” button head Allen bolts and insert the bolt through one of the pan mounting

holes in the outer bolt circle and into the corresponding threaded hole in the seat support. Leave the bolt nger tight.

Repeat this for the remaining two 1/4” x 1 1/2” button head Allen bolts in the top of the table top pan. You may have to adjust the seat

supports or the table top pan in order to get the mounting holes to align.

Aer all the button head Allen bolts are installed, tighten all of the hardware in the lower leg bracket and at the table top pan.

Note: Be careful not to over tighten the button head Allen bolts; the inserts they thread into could unseat and begin to spin with the bolt.

8. Locate one of the seat mounts. Position the seat mount on the lower end of one of the seat supports so that the mounting holes in the seat

mount aligns with the mounting holes in the seat support mounting plate. Install four 5/16”x 1” hex head bolts with 5/16” at washers (top

and bottom) and 5/16” Nylock nuts. Install the remaining seat mounts in the same manner.

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

9. Li the table top and move it over the top of the table top pan. Rotate the table top until the square frame on the bottom of the table top

matches the orientation of the table top pan. Carefully lower the table top down onto the table top pan.

Secure the table top to the table top pan using the remaining eight 1/4” x 1 1/2” button head Allen bolts (two bolts on each side) with a 1/4”

at washer on each of the bolts. You may have to li the table top slightly to get the holes to align.

Leave the bolts nger tight until all of the bolts are started, then use the 5/32” Allen wrench to tighten the bolts.

Note: Be careful not to over tighten the bolts; the inserts they thread into could unseat and begin to spin with the bolts.

10. Place one of the seats (at or contour) over one of the seat mounts. Use four 5/16”x 1” at head socket cap screws with 5/16” at washers

(inside and outside) and 5/16” Nylock nuts. Install the remaining seats in the same manner.

Note: Extra hardware may be included.

11. Move the table to the location where it will be used.

Note: Tables must be surface mounted for stability and to comply with warranty and federal ADA regulations.

12. Aer two weeks, retighten all hardware.

Anova BH1831R Assembly Instruction

Brand: Anova

Model: BH1831R

Category: Computer desks

Type: Assembly Instruction

This manual is also suitable for

Download PDF

report

Anova BH1831R Assembly Instruction

This manual is also suitable for

Anova BH1831R Assembly Instruction

Related papers

Other documents