Push Button DALI DT6 Group Controller 09.2402K8G4.04859
Group 1:
Click to switch on group.
Press and hold down to turn
up brightness of group.
Function introduction
Important: Read All Instructions Prior to Installation
Front side
Group 1:
Click to switch off group.
Press and hold down to turn
down brightness of group.
Group 2 Group 2
Group 3 Group 3
Group 4 Group 4
Rotary Switch for Assigning
Group (Total 16 Groups)
DA DA
DALI INPUT
DALI signal output
Back side
59.3 mm
80 mm
59.3 mm
80 mm
9mm 17.6mm
DA DA
DALI I NP UT
Output DALI signal
Operation Current 30mA
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 80x80x26.6mm
Product Data
Power Supply Supply By DALI Bus
Wiring Diagram
DALI signal
DA DA
DALI BUS
DALI DT6 Device
DALI DT6 Device
DA
DA
DA
DA
Installation
• DO NOT installed with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
• DALI DT6 push button controller
• Ultra slim and luxury design
• Material and finishing color can be customized
• With back lighting design, easy to find even in dark night
• DALI bus powered, no extra power supply required
• Each channel DALI bus can install multiple controllers
• Enables to select and control 4 DALI groups from total 16
DALI groups
• Easy installation with mounting bracket
• Waterproof grade: IP20
1. Do wiring according to connection diagram correctly.
2. Set starting Group number via rotary switch on the back: (0-15 selectable)
• This DALI push button controller enables dimming commands to be sent to Four Groups of devices on the
DALI circuit by Four Groups of buttons. A rotary switch on the back is used to select DALI Groups you would like
to control and set the starting Group number, and total 16 Groups (0-15) can be selected.
• When the rotary switch arrow position is at 0, Group 1 buttons controls all devices on DALI circuit through
broadcast, Group 2 buttons controls DALI group 0,
.
• When the rotary switch arrow position is at X except 0 (1-15), Group 1 buttons controls DALI Group X-1,
.
For example: Rotary switch arrow at 1, Group 1 buttons controls DALI Group 0,
. Rotary switch arrow
at 15,
Please refer to the detailed Group setting table as follows:
Group 3 buttons controls DALI group 1, Group 4 buttons
controls DALI group 2
Group 2 buttons controls DALI Group X, Group 3 buttons controls DALI Group X+1, Group 4 buttons controls
DALI Group X+2
Group 2 buttons controls DALI
Group 1, Group 3 buttons controls DALI Group 2, Group 4 buttons controls DALI Group 3
Group 1 buttons controls DALI Group 14, Group 2 buttons controls DALI Group 15, Group 3 buttons
controls DALI Group 0, Group 4 buttons controls DALI Group 1.
Rotary Switch
Position
DALI Group for
Group 1 Buttons
0
Broadcast
1
0
2
1
3
2
4
3
5
4
6
5
7
6
8
7
9
8
10
9
11
10
12
11
13
12
14
13
15
14
Operation
DALI Group for
Group 2 Buttons 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
DALI Group for
Group 3 Buttons 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0
DALI Group for
Group 4 Buttons 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1
Note: please assign the devices on DALI circuit to a DALI group(0-15) with DALI master controller first.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sunricher SR-2410RG-RGB-GL User manual
-
-
-
-
-
-
-
-
-
Other documents
-
WAGO DALI Configurator User manual
-
Mean Well DLC-02-KN User manual
-
DIODE LED CASAMBI Controllers User guide
-
Mean Well DLC-02 User manual
-
SLV 1006459 Owner's manual
-
-
AUTLED LC-004-944 User manual
-
SBC “DALI F26x” Multimaster Mounting Instructions & Users Guide
-
-
Hytronik HIM13 Dual sense DALI sensor User manual
