SICK WTB11-2P2461S03/P04 Operating instructions

SICK
Brand
SICK
Model
WTB11-2P2461S03/P04
Type
Operating instructions
ENGLISH
Photoelectric Reflex Sensor
with visible redlight
Operating Instructions
Safety notes
> Not a safety component in accordance with EU Machinery Directive.
> Read the operating instructions before commissioning.
> Connection, mounting, and setting is only to be performed by trained
specialists.
> When commissioning, protect the device from moisture and
con
tamination.
Correct use
The photoelectric sensors WTB11-2 are used for detection
of optical, noncontact detection of objects.
Starting operation
1
WTB11-2P2461P04
Maintain direction in which object moves relative to sensor.
Set sensitivity to „max.“. Position object. Position light spot on
object. Yellow LED indicator should light up.
Remove object, yellow LED indicator does not light up any longer
(no inuence from background). Adjustment is completed.
If yellow LED indicator light up anyhow (inuence from background
is too strong), reduce sensitivity until the yellow LED indicator goes
out, position object again.
If yellow LED indicator lights up, the adjustment is completed, if not,
check application conditions such as scanning distance, size and
reectance of object to be detected as well as the reectance of the
background and compare it with characteristic in diagram.
2 WTB11-2P2461S03
Remove object, yellow LED indicator does not light up any longer
(no inuence from background). Adjustment is completed.
If yellow LED indicator light up anyhow (inuence from background
is too strong), reduce sensitivity until the yellow LED indicator goes
out, position object again.
Maintenance
SICK light barriers are maintenance-free. We recommend doing
the following regularly:
- Clean the external lens surfaces.
- Check the screw connections and plug-in connections.
No modications may be made to devices.
DEUTSCH
Reflexions-Lichtschranke
mit sichtbarem Rotlicht (Laser)
Betriebsanleitung
Sicherheitshinweise
> Kein Sicherheitsbauteil gemäß EU-Maschinenrichtlinie.
> Vor der Inbetriebnahme die Betriebsanleitung lesen.
> Anschluss, Montage und Einstellung nur durch Fachpersonal.
> Gerät bei Inbetriebnahme vor Feuchte und Verunreinigung schützen.
Bestimmungsgemäße Verwendung
Die optoelektronischen Sensoren WTB11-2 werden
zum optischen, berührungslosen Erfassen von Sachen eingesetzt.
Inbetriebnahme
1
WTB11-2P2461P04
Bewegungsrichtung des Objektes relativ zum Taster einhalten.
Empndlichkeit auf „max.“ stellen. Objekt positionieren. Lichteck auf
Objekt ausrichten. Gelbe Empfangsanzeige muss permanent leuchten.
Objekt entfernen, gelbe Empfangsanzeige leuchtet nicht mehr (kein
Hintergrundeinuss vorhanden). Einstellung ist beendet.
Falls die gelbe Empfangsanzeige trotzdem leuchtet (Hintergrund-
einuss zu stark), Empndlichkeit reduzieren bis die gelbe Empfangs -
anzeige erlischt, Objekt erneut positionieren.
Wenn gelbe Empfangsanzeige leuchtet, ist die Einstellung beendet,
falls nicht, Einsatzbedingungen wie Tastweite, Objektgröße und Remis-
sionsvermögen des Tastgutes sowie des Hintergrundes überprüfen
und mit der Kennlinie im Diagramm vergleichen.
2 WTB11-2P2461S03
Objekt entfernen, gelbe Empfangsanzeige leuchtet nicht mehr
(kein Hintergrundeinuss vorhanden). Inbetriebnahme ist beendet.
Falls die gelbe Empfangsanzeige trotzdem leuchtet (Hintergrundein-
uss zu stark), Objekt erneut positionieren.
Wartung
SICK-Lichtschranken sind wartungsfrei.
Wir empfehlen, in regelmäßigen Abständen
– die optischen Grenzächen zu reinigen,
– Verschraubungen und Steckverbindungen zu überprüfen.
Veränderungen an Geräten dürfen nicht vorgenommen werden.
More representatives and agencies at www.sick.com ∙ Subject to change
without notice ∙ The specied product features and technical data do not
represent any guarantee.
Weitere Niederlassungen nden Sie unter www.sick.com ∙ Irrtümer
und Änderungen vorbehalten ∙ Angegebene Produkteigenschaften und
technische Daten stellen keine Garantieerklärung dar.
Plus de représentations et d’agences à l’adresse www.sick.com ∙ Sujet à
modication sans préavis ∙ Les caractéristiques de produit et techniques
indiquées ne constituent pas de déclaration de garantie.
Para mais representantes e agências, consulte www.sick.com ∙ Alterações
poderão ser feitas sem prévio aviso ∙ As características do produto e os
dados técnicos apresentados não constituem declaração de garantia.
Altri rappresentanti ed agenzie si trovano su www.sick.com ∙ Contenuti
soggetti a modiche senza preavviso ∙ Le caratteristiche del prodotto e i dati
tecnici non rappresentano una dichiarazione di garanzia.
Más representantes y agencias en www.sick.com ∙ Sujeto a cambio sin
previo aviso ∙ Las características y los datos técnicos especicados no
constituyen ninguna declaración de garantía.
欲了解更多代表机构和代理商信息，请登录 www.sick.com ∙
如有更改, 不另行通知 ∙ 对所给出的产品特性和技术参数
的正确性不予保证。
その他の営業所は www.sick.com よりご覧ください ∙ 予告なしに変更される
ことがあります ∙ 記載されている製品機能および技術データは保証を明示す
るものではありません。
WTB11-
2P2461S03/P04
1
L+
Q
Q
M
4
2
3
brn
blk
wht
blu
WTB11-2P2461S03 WTB11-2P2461P04
Recommended sensing range Empfohlener Schaltabstand Portée de service conseillée Alcance operacional recomendado 30 ... 150 mm / 18%
1)
preadjusted, fixed
30 … 800 mm
1)
adjustable
Light spot diameter / distance Lichtfleckdurchmesser / Entfernung Diamètre de la tache lumineuse
/ distance Diâmetro do ponto de luz / distância 6 mm @ 200 mm 6 mm @ 200 mm
Supply voltage V
S
Versorgungsspannung U
V
Tension d‘alimentation U
V
Tensão de força U
V
DC 10 ... 30 V
2)
DC 10 ... 30 V
2)
Output current I
max
Ausgangsstrom I
max.
Courant de sortie I
max.
Corrente de saída I
max.
100 mA 100 mA
Response time Ansprechzeit Temps de réponse Tempo de reação < 2.5 ms
3)
< 2.5 ms
3)
Switching frequency Schaltfolge max. Fréquence max. Sequência max. de sinais 200 Hz
4)
200 Hz
4)
Enclosure rating Schutzart Type de protection Tipo de proteção IP 67 IP 67
Protection class Schutzklasse Classe de protection Classe de proteção
5)
5)
Circuit protection Schutzschaltungen Circuits de protection Circuitos protetores A, B, C
6)
A, B, C
Ambient operating temperature Betriebsumgebungstemperatur Température ambiante Temperatura ambiente de operação -30 ... +60 °C -30 ... +60 °C
Incl. mounting bracket Inkl. Haltewinkel Incl. équerre de fixation Incl. ângulo de suporte
1)
Object 90 % reflection according to DIN 5033
2)
Limit values: Operation in
short-circuit protected network
max. 8 A ripple
max. 5 V
pp
3)
With light / dark ratio 1:1
4)
Signal transit time with resistive load
5)
Reference voltage 50 V DC
6)
A = V
S
connections reversepolarity protected
B = Outputs short-circuit protected suppression
C = Interference pulse suppression
1)
Objekt 90 % Remission nach DIN 5033
2)
Grenzwerte: Betrieb im
kurzschlussgeschützen Netz
max. 8 A; Restwelligkeit
max. 5 V
SS
3)
Bei Hell / Dunkelverhältnis 1:1
4)
Signallaufzeit bei ohmscher Last
5)
Bemessungsspannung DC 50 V
6)
A = U
V
-Anschlüsse verpolsicher
B = Ausgänge kurzschlussfest
C = Störimpulsunterdrückung
1)
Objet Luminance de 90 % selon DIN 5033
2)
Valeurs limites Service dans un réseau
protégév contre les courts-circuits 8 A au
max. Ondulation résiduelle max. 5 V
SS
3)
Pour un rapport clair / sombre 1:1
4)
Durée du signal en charge ohmique
5)
Tension de calcul 50 V c.c.
6)
A = Raccordements U
V
protégés contre
les inversions de polarité
B = Sorties sans court-circuit
C = Suppression des impulsions parasites
1)
Objeto: 90 % de remissão segundo DIN 5033
2)
Valores limite Operação em rede protegida
contra curto-circuitos max. 8 A Ondulação
residual max. 5 V
SS
3)
Com uma relação luminoso / escuro de 1:1
4)
Tempo de transição do sinal com carga ôhmica
5)
Tensão de dimensionamento DC 50 V
6)
A = Conexões U
V
protegidas contra inversão de polos
B = Saídas à prova de curto-circuito
C = Supressão de impulsos parasitas
WTB11-2P2461S03 WTB11-2P2461P04
Distanza di lavoro consigliata Alcance de servicio recomendado
建议的有效工作距离 推奨動作範囲
30 ... 150 mm / 18%
1)
preadjusted, fixed
30 … 800 mm
1)
adjustable
Diametro punto luminoso / distanza Diámetro / distancia de mancha de luz
光点直径 / 距离 スポット径 / 距離 6 mm @ 200 mm 6 mm @ 200 mm
Tensione di alimentazione U
V
Tensión de alimentación U
V
电源电压U
V
供給電圧 U
V
DC 10 ... 30 V
2)
DC 10 ... 30 V
2)
Corrente di uscita I
max.
Corriente de salida I
max.
输出电流I
max.
最大出力電流 I
max.
100 mA 100 mA
Tempo di risposta Tiempo de reacción
触发时间 応答時間
< 2.5 ms
3)
< 2.5 ms
3)
Sequenza signali max. Secuencia de señales max. 信号流 max. 切替順序 max. 200 Hz
4)
200 Hz
4)
Tipo di protezione Tipo de protección
保护种类 保護等級
IP 67 IP 67
Classe di protezione Protección clase
保护级别 保護クラス
5)
5)
Commutazioni di protezione Circuitos de protección
保护电路 保護回路
A, B, C
6)
A, B, C
Temperatura ambiente circostante Temperatura ambiente de servicio
工作环境-温度 使用周囲温度
-30 ... +60 °C -30 ... +60 °C
Con staffa angolare Incl. escuadra de montaje
含支撑角 取付ブラケットを含む
1)
Oggetto 90 %, remissione sec. DIN 5033
2)
Valori limite Funzionamento in rete con
protezione dai cortocircuiti max. 8 A
ondulazione residua max. 5 V
SS
3)
Con relatio chiaro / scuro 1:1
4)
Tempo di continuare de segnale a resistenza ohmica
5)
Tensione di taratura DC 50 V
6)
A = U
V
-collegamenti con protez. contro inversione di poli
B = Uscite resistenti al corto circuito
C = Soppressione impulsi di disturbo
1)
Objeto 90 % de remission en base a DIN 5033
2)
Valores límite Funcionamiento en la red
protegida contra cortocircuito, max. 8 A
ondulación residual max. 5 V
SS
3)
Con una relación claro / oscuro de 1:1
4)
Duración de la señal con carga óhmica
5)
Tensión tolerable DC 50 V
6)
A = Conexiones U
V
a prueba de inversión de polaridad
B = Salidas a prueba de cortocircuitos
C = Represión de impulso de interferencia
1)
90 % 漫反射比物体按照 DIN 5033
2)
操作电流：在防短路的网络里， 最大8
极限值剩余波纹度 max. 5 V
SS
3)
亮 / 暗比 1:1
4)
电阻性负载时，传感器检测到变化时输出信号的转
换时间
5)
限定电压 DC 50 V
6)
A = U
V
-接头防反接
B = 防短路的输出端
C = 消除干扰脉冲
1)
対象物 90 % の反射率 DIN 5033 に準拠
2)
限界値：短絡防止回路での動作
最大 8 A、残留リップル
最大 5 V
SS
3)
明暗比率 1:1の場合
4)
抵抗負荷における信号遷移時間
5)
定格電圧 DC 50 V
6)
A = U
V
接続 逆接保護
B = 短絡防止出力
C = 干渉パルス制御
------------------------------------------------------- 8015828.10DD 1218 COMAT -----------------------------------------------------
0 100
(3.94)
300
(11.81)
500
(19.69)
700
(27.56)
900
(35.43)
1100
(43.31)
30
15
20
25
10
0
5
% of sensing distance
Distance in mm (inch)
WTB11-2P / N / K2461
6% / 90%
18% / 90%
90% / 90%
19.4
(0.76)
21.3
(0.84)
32 (1.26)
15.6
(0.61)
ø 4.2
(0.91)
7.3
(0.29)
3.2
(0.13)
23.1
(0.91)
6.1
(0.24)
48.5
(1.91)
5.1
(0.2)
42
(1.65)
D
Q (PNP)
Q (NPN)
L
L
1
0
1
0
1
0
1
0
D
1 + 2 WTB11-2P2461P04 WTB11-2P2461S03
A WTB11-2P2461S03/P04
D = dark-switching / dunkelschaltend
L = light-switching / hellschaltend
B WTB11-2P2461S03/P04
2006/42/EG
NO
SAFETY
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BZ int48
Please find detailed addresses and further locations in all major industrial
nations at www.sick.com
Australia
Phone +61 (3) 9457 0600
Austria
Phone +43 (0) 2236 62288-0
Belgium/Luxembourg
Phone +32 (0) 2 466 55 66
Brazil
Phone +55 11 3215-4900
Canada
Phone +1 905.771.1444
Czech Republic
Phone +420 2 57 91 18 50
Chile
Phone +56 (2) 2274 7430
China
Phone +86 20 2882 3600
Denmark
Phone +45 45 82 64 00
Finland
Phone +358-9-25 15 800
France
Phone +33 1 64 62 35 00
Germany
Phone +49 (0) 2 11 53 01
Hong Kong
Phone +852 2153 6300
Hungary
Phone +36 1 371 2680
India
Phone +91-22-6119 8900
Israel
Phone +972-4-6881000
Italy
Phone +39 02 27 43 41
Japan
Phone +81 3 5309 2112
Malaysia
Phone +603-8080 7425
Mexico
Phone +52 (472) 748 9451
Netherlands
Phone +31 (0) 30 229 25 44
New Zealand
Phone +64 9 415 0459
Norway
Phone +47 67 81 50 00
Poland
Phone +48 22 539 41 00
Romania
Phone +40 356-17 11 20
Russia
Phone +7 495 283 09 90
Singapore
Phone +65 6744 3732
Slovakia
Phone +421 482 901 201
Slovenia
Phone +386 591 78849
South Africa
Phone +27 (0)11 472 3733
South Korea
Phone +82 2 786 6321
Spain
Phone +34 93 480 31 00
Sweden
Phone +46 10 110 10 00
Switzerland
Phone +41 41 619 29 39
Taiwan
Phone +886-2-2375-6288
Thailand
Phone +66 2 645 0009
Turkey
Phone +90 (216) 528 50 00
United Arab Emirates
Phone +971 (0) 4 88 65 878
United Kingdom
Phone +44 (0)17278 31121
USA
Phone +1 800.325.7425
Vietnam
Phone +65 6744 3732
BZ int48
Please find detailed addresses and further locations in all major industrial
nations at www.sick.com
Australia
Phone +61 (3) 9457 0600
Austria
Phone +43 (0) 2236 62288-0
Belgium/Luxembourg
Phone +32 (0) 2 466 55 66
Brazil
Phone +55 11 3215-4900
Canada
Phone +1 905.771.1444
Czech Republic
Phone +420 2 57 91 18 50
Chile
Phone +56 (2) 2274 7430
China
Phone +86 20 2882 3600
Denmark
Phone +45 45 82 64 00
Finland
Phone +358-9-25 15 800
France
Phone +33 1 64 62 35 00
Germany
Phone +49 (0) 2 11 53 01
Hong Kong
Phone +852 2153 6300
Hungary
Phone +36 1 371 2680
India
Phone +91-22-6119 8900
Israel
Phone +972-4-6881000
Italy
Phone +39 02 27 43 41
Japan
Phone +81 3 5309 2112
Malaysia
Phone +603-8080 7425
Mexico
Phone +52 (472) 748 9451
Netherlands
Phone +31 (0) 30 229 25 44
New Zealand
Phone +64 9 415 0459
Norway
Phone +47 67 81 50 00
Poland
Phone +48 22 539 41 00
Romania
Phone +40 356-17 11 20
Russia
Phone +7 495 283 09 90
Singapore
Phone +65 6744 3732
Slovakia
Phone +421 482 901 201
Slovenia
Phone +386 591 78849
South Africa
Phone +27 (0)11 472 3733
South Korea
Phone +82 2 786 6321
Spain
Phone +34 93 480 31 00
Sweden
Phone +46 10 110 10 00
Switzerland
Phone +41 41 619 29 39
Taiwan
Phone +886-2-2375-6288
Thailand
Phone +66 2 645 0009
Turkey
Phone +90 (216) 528 50 00
United Arab Emirates
Phone +971 (0) 4 88 65 878
United Kingdom
Phone +44 (0)17278 31121
USA
Phone +1 800.325.7425
Vietnam
Phone +65 6744 3732
SICK AG, Erwin-Sick-Strasse 1, D-79183 Waldkirch
Page is loading ...
  • Page 1 1
  • Page 2 2

SICK WTB11-2P2461S03/P04 Operating instructions

SICK
Brand
SICK
Model
WTB11-2P2461S03/P04
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers