T: 020 7387 9951 www.allgood.co.uk1
Recycle responsibly
Allgood size 2-4 surface cam closer fitting instructions
9267N-6
issue 01:11/21
1
1
2
3
1
1
2
3
8
EN 2-4
max. 1100mm
1
12 3
A
A
1
2
7
5
mm
8
EN 2-4
max. 1100mm
Max
120°
13
1
B
B
1
2
≥EN3
Installation and Maintenance Instructions:
Maintenance
1.Once the unit has been correctly fitted it is recommended that periodic
checks (every six months) are carried out to ensure all fixings are tight and
the door closes freely and positively into the frame, without slamming.
2.A light oil lubricant (non-graphite) should be applied to the moving joints and
exposed pivot points. Hinges should be maintained in accordance with the
manufacturer’s instructions.
After Installation
1.When the closer operates to close the door from its maximum opening
position, it should ensure the lock latchbolt and any seals are overcome and
the leaf returned into its frame.
2.When the door is slightly open and the latch bolt resting against the strike,
release the door to ensure the leaf fully closes into its frame.
3.It is recommended to fit door stops to prevent the door opening beyond its
limits.
Warning
1.Please note the minimum power size requirement for fire / smoke door assemblies is 3 as required by Approved Document B.
2.Do not install mechanical hold open devices on fire / smoke door assemblies.
3.Take care not to exceed the maximum opening angle as detailed above.
4.Care and attention must be taken when adjusting any of the units control valves to avoid damage through over adjustment.
5.All Allgood Door Closer units are sealed for life and the internal components assembled under high load, therefore, tampering
with the mechanism is to be strictly avoided.
Factory preset
EN3 EN4EN2
x0 x2x3
850mm
Max
40Kg
950mm
Max
60Kg
1100mm
Max
80Kg
≥EN3
Factory preset
EN3 EN4EN2
x0 x2x3
850mm
Max
40Kg
950mm
Max
60Kg
1100mm
Max
80Kg
12
23
1
2
3
4
6
5
mm
Max. 10Nm
75
mm
11
BC
60°
4
10
3120°
10°
9
2
0°
10°
290°
51
5
mm
2
345°
1
1
4
1
23
12
3
4
5
2
90°
1
9
10°
0°
2
10
10°
180° 3
1
2
3
45°
1
4
1
6
5
mm
5
mm
Max. 10Nm
4
70° BC
11
Fixing Instructions for : S3406
Door Closer Power Adjustable EN 2~4
Regular Fixing : Push Side Application
Transom Fixing : Pull Side Application
ISSUE 04:09/21
11009 ZINC-T0162-3Swww.synergyhardware.co.uk
1
1
2
3
1
1
2
3
12
APPROVED
PRODUCT
CF5312
2812
CPR-AD5198
15
21
BS EN1154:1997+ A1:2002
484
2113
www.synergyhardware.co.uk
1121-UK
CPR-AD7833
1
1
2
3
1
1
2
3
8
EN 2-4
max. 1100mm
1
12 3
A
A
1
2
7
5
mm
8
EN 2-4
max. 1100mm
1 2 3
Max
120°
13
1
B
B
1
2
≥EN3
Installation and Maintenance Instructions:
Maintenance
1.Once the unit has been correctly fitted it is recommended that periodic
checks (every six months) are carried out to ensure all fixings are tight and
the door closes freely and positively into the frame, without slamming.
2.A light oil lubricant (non-graphite) should be applied to the moving joints and
exposed pivot points. Hinges should be maintained in accordance with the
manufacturer’s instructions.
After Installation
1.When the closer operates to close the door from its maximum opening
position, it should ensure the lock latchbolt and any seals are overcome and
the leaf returned into its frame.
2.When the door is slightly open and the latch bolt resting against the strike,
release the door to ensure the leaf fully closes into its frame.
3.It is recommended to fit door stops to prevent the door opening beyond its
limits.
Warning
1.Please note the minimum power size requirement for fire / smoke door assemblies is 3 as required by Approved Document B.
2.Do not install mechanical hold open devices on fire / smoke door assemblies.
3.Take care not to exceed the maximum opening angle as detailed above.
4.Care and attention must be taken when adjusting any of the units control valves to avoid damage through over adjustment.
5.All Allgood Door Closer units are sealed for life and the internal components assembled under high load, therefore, tampering
with the mechanism is to be strictly avoided.
Factory preset
EN3 EN4EN2
x0 x2x3
850mm
Max
40Kg
950mm
Max
60Kg
1100mm
Max
80Kg
≥EN3
Factory preset
EN3 EN4EN2
x0 x2x3
850mm
Max
40Kg
950mm
Max
60Kg
1100mm
Max
80Kg
12
23
1
2
3
4
6
5
mm
Max. 10Nm
75
mm
11
BC
60°
4
10
3120°
10°
9
2
0°
10°
290°
51
5
mm
2
345°
1
1
4
1
23
12
3
4
5
2
90°
1
9
10°
0°
2
10
10°
180° 3
1
2
3
45°
1
4
1
6
5
mm
5
mm
Max. 10Nm
4
70° BC
11
Fixing Instructions for : S3406
Door Closer Power Adjustable EN 2~4
Regular Fixing : Push Side Application
Transom Fixing : Pull Side Application
ISSUE 04:09/21
11009 ZINC-T0162-3Swww.synergyhardware.co.uk
1
1
2
3
1
1
2
3
12
APPROVED
PRODUCT
CF5312
2812
CPR-AD5198
15
21
BS EN1154:1997+ A1:2002
484
2113
www.synergyhardware.co.uk
1121-UK
CPR-AD7833
