Panasonic ETPKD100H Datasheet

Category
Projector mounts
Type
Datasheet

This manual is also suitable for

Attachment plate
Attachment plate
Projector
Ø60.5
290
* Adjustable in 40-mm (1-9/16˝) steps.
175 62.5
50
200
300
87.5
150
440
416.5–536.5*
200
314
344
344
54
581–701
(Ø2-3/8˝)
(11-13/32˝)
(6-7/8˝)
(2-15/32˝)
(1-31/32˝)
(7-7/8˝)
(11-13/16˝)
(3-7/16˝)
(5-29/32˝)
(17-5/16˝)
(16-13/32˝–21-1/8˝)
(7-7/8˝)
(12-3/8˝)
(13-17/32˝)
(13-17/32˝)
(2-1/8˝)
(22-7/8˝–27-19/32˝)
S PEC F ILE
ET-PKD100H
Ceiling mount bracket for high ceilings
As of December 2006 < 1 >
Specifications
Vertical correction angle: +5°, -17°
Horizontal slant correction angle: ±2.5°
Horizontal turn correction angle: ±1.2°
Dimensions (W x H x D): 536 x 416.5536.5 x 425 mm
(21-3/32˝ x 16-13/32˝–21-1/8˝ x 16-23/32˝)
Weight: 16.6 kg (36.6 lbs)
Attachment plateIllustration shows the ET-PKD100H attached to the projector.
Parts
Attachment plate . . . . . . . . . . . . . . . . . . . . . . . . 1
Projector mount bracket . . . . . . . . . . . . . . . . . . . 1
Adjuster poles . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Angle adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pole support bracket 1 . . . . . . . . . . . . . . . . . . . . 1
Pole support brackets 2 . . . . . . . . . . . . . . . . . . . 2
Pole fixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hexagonal bolt (M6 x 110) . . . . . . . . . . . . . . . . . 1
Spring washer (M6) . . . . . . . . . . . . . . . . . . . . . . 1
Nut (M6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Washer-fitted hex bolts (M6 x 12) . . . . . . . . . . 36
Sealing packing . . . . . . . . . . . . . . . . . . . . . . . . . 1
Washer-fitted hex bolts (M6 x 25) . . . . . . . . . . . 5
Washers (M6) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Hex nuts (M6) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Sealing packing . . . . . . . . . . . . . . . . . . . . . . . . . 1
Weights and dimensions shown are approximate. Specifications subject to change without notice.
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
Dimensions
Description
This ceiling mount bracket is to be used when mounting Panasonic projectors to the ceiling.
Caution:
Mounting should be done by a qualified technician. Make sure that the mounting (ceiling) area has
sufficient strength. Read the enclosed mounting instructions thoroughly before starting.
  • Page 1 1

Panasonic ETPKD100H Datasheet

Category
Projector mounts
Type
Datasheet
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI