Page is loading ...
R&S®RTP
High-Performance Oscilloscope
User Manual
1803648402
Version 03
(B3Îâ2)
This manual describes the following R&S®RTP models with firmware version 5.30:
●R&S®RTP044B (1803.7000K04)
●R&S®RTP064B (1803.7000K06)
●R&S®RTP084B (1803.7000K08)
●R&S®RTP134B (1803.7000K13)
●R&S®RTP164B (1803.7000K16)
© 2023 Rohde & Schwarz GmbH & Co. KG
Muehldorfstr. 15, 81671 Muenchen, Germany
Phone: +49 89 41 29 - 0
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered
trademarks of HDMI Licensing Administrator, Inc.
TEKTRONIX, TEK, and TEKPROBE are registered trademarks of Tektronix, Inc.
All other trademarks are the properties of their respective owners.
1803.6484.02 | Version 03 | R&S®RTP
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol, e.g. R&S®RTP is indicated as
R&S RTP.
Contents
R&S®RTP
3User Manual 1803.6484.02 ─ 03
Contents
1 Safety and regulatory information......................................................11
1.1 Safety instructions...................................................................................................... 11
1.2 Labels on the product.................................................................................................16
1.3 Warning messages in the documentation................................................................ 16
1.4 Where to find key documents on Rohde & Schwarz............................................... 17
1.5 Korea certification class A......................................................................................... 17
2 Preface.................................................................................................. 18
2.1 Key features.................................................................................................................18
2.2 Documentation overview............................................................................................18
2.3 Options described in this document.........................................................................20
2.4 Conventions used in the documentation..................................................................22
3 Getting started......................................................................................24
3.1 Preparing for use........................................................................................................ 24
3.2 Instrument tour............................................................................................................31
3.3 Operating the instrument........................................................................................... 43
4 Instrument setup..................................................................................70
4.1 System settings...........................................................................................................70
4.2 Option settings............................................................................................................74
4.3 Appearance settings...................................................................................................77
4.4 Display settings...........................................................................................................93
4.5 Frontpanel settings.....................................................................................................97
4.6 Preset setup...............................................................................................................101
4.7 Maintenance settings................................................................................................103
4.8 Save / recall............................................................................................................... 107
5 Acquisition and waveform setup......................................................112
5.1 Basics.........................................................................................................................112
5.2 Horizontal...................................................................................................................122
5.3 Horizontal accuracy.................................................................................................. 125
5.4 Acquire settings........................................................................................................ 128
5.5 Vertical setup.............................................................................................................140
Contents
R&S®RTP
4User Manual 1803.6484.02 ─ 03
5.6 Probes........................................................................................................................ 146
5.7 R&S RT-ZVC probe....................................................................................................174
5.8 Differential signals.................................................................................................... 184
5.9 Setting up the waveform.......................................................................................... 188
6 Triggers............................................................................................... 193
6.1 Basics of triggering.................................................................................................. 193
6.2 Setting up the trigger................................................................................................194
6.3 Trigger types..............................................................................................................196
6.4 Mode / Holdoff........................................................................................................... 225
6.5 Conditioning.............................................................................................................. 228
6.6 Actions on trigger..................................................................................................... 229
6.7 Qualification.............................................................................................................. 231
6.8 Sequence................................................................................................................... 234
6.9 Zone trigger............................................................................................................... 237
6.10 High speed serial pattern trigger (option R&S RTP-K140/K141).......................... 241
6.11 External trigger input................................................................................................256
7 Waveform analysis.............................................................................261
7.1 Zoom.......................................................................................................................... 261
7.2 Reference waveforms............................................................................................... 271
7.3 Mathematics.............................................................................................................. 279
7.4 History........................................................................................................................298
7.5 XY-diagram................................................................................................................ 304
8 Measurements....................................................................................308
8.1 Cursor measurements.............................................................................................. 308
8.2 Automatic measurements........................................................................................ 319
8.3 Quick measurements................................................................................................396
9 Spectrum analysis............................................................................. 399
9.1 FFT analysis.............................................................................................................. 399
9.2 Spectrum analysis (option R&S RTP-K37)............................................................. 419
10 Mask testing....................................................................................... 423
10.1 About mask testing...................................................................................................423
10.2 Mask test settings..................................................................................................... 425
Contents
R&S®RTP
5User Manual 1803.6484.02 ─ 03
10.3 Mask testing on eye diagrams................................................................................. 437
10.4 Working with masks..................................................................................................441
11 Search functions................................................................................ 449
11.1 Overview: search definition and results................................................................. 449
11.2 Search setup..............................................................................................................450
11.3 Search gate................................................................................................................465
11.4 Search display presentation.................................................................................... 468
12 Data and file management.................................................................473
12.1 Save and recall user settings...................................................................................473
12.2 Save and recall waveform data and results............................................................482
12.3 Screenshots...............................................................................................................507
12.4 Reports.......................................................................................................................511
12.5 File selection dialog..................................................................................................513
13 Protocol analysis............................................................................... 515
13.1 Basics of protocol analysis......................................................................................515
13.2 I²C (option R&S RTP-K1)...........................................................................................525
13.3 SPI bus (option R&S RTP-K1).................................................................................. 539
13.4 UART/RS-232/RS-422/RS-485 (option R&S RTP-K2)..............................................550
13.5 CAN and CAN FD (option R&S RTP-K3/K9)............................................................559
13.6 LIN (option R&S RTP-K3)..........................................................................................585
13.7 MIL-1553 (option R&S RTP-K6)................................................................................599
13.8 ARINC 429 (option R&S RTP-K7).............................................................................616
13.9 Ethernet 10BASE-T and 100BASE-TX (option R&S RTP-K8)................................ 629
13.10 Ethernet 100BASE-T1 (option R&S RTP-57)...........................................................644
13.11 Ethernet 1000BASE-T1 (option R&S RTP-K58)...................................................... 663
13.12 RFFE (option R&S RTP-K40)....................................................................................681
13.13 D-PHY (option R&S RTP-K42).................................................................................. 702
13.14 M-PHY and USB SSIC (option R&S RTP-K44 and K64)......................................... 718
13.15 Custom: Manchester / NRZ (option R&S RTP-K50)............................................... 748
13.16 8b/10b (option R&S RTP-K52)..................................................................................781
13.17 MDIO (option R&S RTP-K55)....................................................................................794
13.18 USB (option R&S RTP-K60)......................................................................................807
Contents
R&S®RTP
6User Manual 1803.6484.02 ─ 03
13.19 USB 3.1 (option R&S RTP-K61/K62)........................................................................ 834
13.20 USBPD (option R&S RTP-K63).................................................................................856
13.21 SpaceWire (option R&S RTP-K65)...........................................................................869
13.22 PCIe (option R&S RTP-K72/K73)..............................................................................881
13.23 DDR (option R&S RTP-K91/K93 ).............................................................................916
14 Mixed signal option (MSO, R&S RTP-B1)........................................ 938
14.1 Digital channels and parallel buses........................................................................ 938
14.2 Display....................................................................................................................... 947
14.3 Trigger........................................................................................................................ 949
14.4 Measurements on digital channels......................................................................... 962
14.5 Data export................................................................................................................ 963
14.6 Mathematics.............................................................................................................. 964
14.7 Search........................................................................................................................ 964
15 Waveform generator (option R&S RTP-B6)..................................... 966
15.1 Setup of the waveform generator............................................................................ 966
15.2 Setup of the pattern generator.................................................................................985
15.3 Output........................................................................................................................ 988
15.4 Coupling settings......................................................................................................991
15.5 Sync settings.............................................................................................................992
15.6 Configuring the waveform generator...................................................................... 993
16 Pulse source and TDR/TDT analysis (options R&S RTP-B7/K130)
............................................................................................................. 997
16.1 Pulse source (option R&S RTP-B7).........................................................................997
16.2 TDR/TDT analysis (option R&S RTP-K130).............................................................999
17 I/Q software interface (option R&S RTP-K11)................................1014
17.1 I/Q mode...................................................................................................................1014
17.2 I/Q sampling setup.................................................................................................. 1014
17.3 I/Q data output.........................................................................................................1020
17.4 Deembedding in I/Q mode......................................................................................1021
18 Jitter analysis and clock data recovery......................................... 1023
18.1 Jitter measurements (option R&S RTP-K12)........................................................ 1024
18.2 Advanced jitter and noise (option R&S RTP-K133/K134)....................................1033
Contents
R&S®RTP
7User Manual 1803.6484.02 ─ 03
18.3 Clock data recovery................................................................................................ 1067
19 Advanced eye diagram analysis (option R&S RTP-K136/K137).. 1072
19.1 Calculation and display of advanced eye diagrams............................................ 1072
19.2 Eye diagram setup.................................................................................................. 1073
19.3 Measurements and zoom on eye diagrams..........................................................1085
19.4 Mask Testing on Eye Diagrams..............................................................................1086
20 Deembedding (option R&S RTP-K121/-K122)................................1087
20.1 Configuring the measurement setup for deembedding...................................... 1087
20.2 Deembedding settings............................................................................................1088
20.3 Responses............................................................................................................... 1097
20.4 Proven probe, proven cable...................................................................................1098
21 External frontend control (option R&S RTP-K553)....................... 1103
21.1 External frontend basics........................................................................................ 1103
21.2 Test setups...............................................................................................................1104
21.3 Settings for frontend control..................................................................................1107
21.4 Using frontends to get I/Q data.............................................................................. 1114
21.5 Using frontends to get raw data.............................................................................1115
21.6 Troubleshooting frontend control..........................................................................1117
22 Compliance tests..............................................................................1121
22.1 USB compliance test...............................................................................................1122
22.2 Ethernet compliance tests (options R&S RTP-K22/K23/K25/K86)......................1124
22.3 D-PHY compliance tests (option R&S RTP-K26).................................................. 1126
22.4 eMMC compliance tests (option R&S RTP-K92)...................................................1127
22.5 PCIe compliance tests (option R&S RTP-K81)..................................................... 1128
22.6 DDR3 compliance tests (option R&S RTP-K91)................................................... 1129
22.7 DDR4 compliance tests (option R&S RTP-K93)................................................... 1130
22.8 C-PHY compliance tests (option R&S RTP-K28).................................................. 1130
23 Network operation and remote control.......................................... 1132
23.1 Operating system.................................................................................................... 1132
23.2 Setting up a network (LAN) connection................................................................ 1137
23.3 Web interface...........................................................................................................1142
23.4 Remote Desktop connection..................................................................................1147
Contents
R&S®RTP
8User Manual 1803.6484.02 ─ 03
23.5 Remote control........................................................................................................ 1149
24 Remote control commands.............................................................1165
24.1 Conventions used in remote command description............................................1171
24.2 Finding the appropriate command........................................................................ 1172
24.3 Programming examples..........................................................................................1172
24.4 Frequently used parameters and suffixes............................................................ 1188
24.5 Common commands...............................................................................................1196
24.6 General remote settings......................................................................................... 1201
24.7 Instrument setup..................................................................................................... 1205
24.8 Acquisition and setup.............................................................................................1234
24.9 Trigger...................................................................................................................... 1304
24.10 Waveform analysis..................................................................................................1378
24.11 Cursor measurements............................................................................................ 1413
24.12 Automatic measurements...................................................................................... 1426
24.13 Spectrum analysis.................................................................................................. 1524
24.14 Mask testing............................................................................................................ 1542
24.15 Search...................................................................................................................... 1565
24.16 Data management................................................................................................... 1604
24.17 Protocols..................................................................................................................1636
24.18 Mixed signal option (MSO, R&S RTP-B1)............................................................. 2309
24.19 Waveform generator (option R&S RTP-B6).......................................................... 2334
24.20 Pulse source and TDR/TDT analysis (options R&S RTP-B7/K130).................... 2357
24.21 I/Q software interface (option R&S RTP-K11).......................................................2366
24.22 Jitter analysis and clock data recovery................................................................ 2373
24.23 Eye diagram analysis..............................................................................................2412
24.24 Deembedding (option R&S RTP-K121/-K122).......................................................2432
24.25 External frontend control (option R&S RTP-K553).............................................. 2444
24.26 Maintenance............................................................................................................ 2460
24.27 Status reporting...................................................................................................... 2463
24.28 Remote trace........................................................................................................... 2469
24.29 Deprecated commands...........................................................................................2473
25 Maintenance and support................................................................2475
25.1 Cleaning................................................................................................................... 2475
Contents
R&S®RTP
9User Manual 1803.6484.02 ─ 03
25.2 Power cables for R&S RTP.....................................................................................2475
25.3 Contacting customer support................................................................................2476
25.4 Information for technical support..........................................................................2476
25.5 Data security............................................................................................................2477
25.6 Transporting............................................................................................................ 2477
25.7 Storage.....................................................................................................................2477
25.8 Disposal................................................................................................................... 2478
List of commands............................................................................ 2479
Index..................................................................................................2552
Contents
R&S®RTP
10User Manual 1803.6484.02 ─ 03
Safety and regulatory information
R&S®RTP
11User Manual 1803.6484.02 ─ 03
1 Safety and regulatory information
The product documentation helps you to use the product safely and efficiently. Follow
the instructions provided here and in the Chapter 1.1, "Safety instructions",
on page 11.
Intended use
The R&S RTP oscilloscope is designed for measurements on circuits that are only indi-
rectly connected to the mains or not connected at all. It is not rated for any measure-
ment category.
The product is intended for the development, production and verification of electronic
components and devices in industrial, administrative, and laboratory environments.
Use the product only for its designated purpose. Observe the operating conditions and
performance limits stated in the data sheet.
Where do I find safety information?
Safety information is part of the product documentation. It warns you of potential dan-
gers and gives instructions on how to prevent personal injury or damage caused by
dangerous situations. Safety information is provided as follows:
●In Chapter 1.1, "Safety instructions", on page 11. The same information is provi-
ded in many languages as printed "Safety Instructions". The printed "Safety
Instructions" are delivered with the product.
●Throughout the documentation, safety instructions are provided when you need to
take care during setup or operation.
1.1 Safety instructions
Products from the Rohde & Schwarz group of companies are manufactured according
to the highest technical standards. To use the products safely, follow the instructions
provided here and in the product documentation. Keep the product documentation
nearby and offer it to other users.
Use the product only for its intended use and within its performance limits. Intended
use and limits are described in the product documentation such as the data sheet,
manuals and the printed "Safety Instructions for Oscilloscopes and Accessories" docu-
ment. If you are unsure about the appropriate use, contact Rohde & Schwarz customer
service.
Using the product requires specialists or specially trained personnel. These users also
need sound knowledge of at least one of the languages in which the user interfaces
and the product documentation are available.
Reconfigure or adjust the product only as described in the product documentation or
the data sheet. Any other modifications can affect safety and are not permitted.
Never open the casing of the product. Only service personnel authorized by
Rohde & Schwarz are allowed to repair the product. If any part of the product is dam-
Safety instructions
Safety and regulatory information
R&S®RTP
12User Manual 1803.6484.02 ─ 03
aged or broken, stop using the product. Contact Rohde & Schwarz customer service at
https://www.rohde-schwarz.com/support.
In these safety instructions, the term "product" covers instruments (oscilloscopes),
probes and their accessories.
Lifting and carrying the instrument
Check the data sheet for the maximum weight of the instrument. A single person can
only carry a maximum of 18 kg safely depending on age, gender and physical condi-
tion. If your instrument is heavier than 18 kg, do not move or carry it by yourself.
Use the instrument handles to move or carry the instrument. Do not use the mounted
accessories instead of the handles. Accessories are not designed to carry the weight
of the instrument.
To move the instrument safely, you can use lifting or transporting equipment such as lift
trucks and forklifts. Follow the instructions provided by the equipment manufacturer.
Choosing the operating site
Only use the product indoors. The product casing is not waterproof. Water that enters
can electrically connect the casing with live parts, which can lead to electric shock,
serious personal injury or death if you touch the casing. If Rohde & Schwarz provides
accessories designed for outdoor use of your product, e.g. a protective cover, you can
use the product outdoors.
Unless otherwise specified in the data sheet, you can operate the product up to an alti-
tude of 2000 m above sea level.
The product is suitable for pollution degree 2 environments where nonconductive con-
tamination can occur. For more information on environmental conditions such as ambi-
ent temperature and humidity, see the data sheet.
Setting up the product
Always place the product on a stable, flat and level surface with the bottom of the prod-
uct facing down. If the product is designed for different positions, secure the product so
that it cannot fall over.
If the product has foldable feet, always fold the feet completely in or out to ensure sta-
bility. The feet can collapse if they are not folded out completely or if the product is
moved without lifting it. The foldable feet are designed to carry the weight of the prod-
uct, but not an extra load.
If stacking is possible, keep in mind that a stack of products can fall over and cause
injury.
If you mount products in a rack, ensure that the rack has sufficient load capacity and
stability. Observe the specifications of the rack manufacturer. Always install the prod-
ucts from the bottom shelf to the top shelf so that the rack stands securely. Secure the
product so that it cannot fall off the rack.
Safety instructions
Safety and regulatory information
R&S®RTP
13User Manual 1803.6484.02 ─ 03
Connecting to power and grounding
The mains power supply input of the instrument complies with overvoltage category II.
It has to be connected to a fixed installation used to supply energy-consuming equip-
ment such as household appliances and similar loads. Be aware that electrically pow-
ered products have risks, such as electric shock, fire, personal injury or even death.
Take the following measures for your safety:
●Do not use an isolating transformer to connect the instrument to the mains power
supply.
●Before switching on the product, ensure that the voltage and frequency indicated
on the product match the available power source. If the power adapter does not
adjust automatically, set the correct value and check the rating of the fuse.
●Only use the power cable delivered with the product. It complies with country-spe-
cific safety requirements. Only insert the plug into an outlet with protective conduc-
tor terminal.
●If a product has an exchangeable fuse, its type and characteristics are indicated
next to the fuse holder. Before changing the fuse, switch off the instrument and dis-
connect it from the power source. How to change the fuse is described in the prod-
uct documentation.
●Only use intact cables and route them carefully so that they cannot be damaged.
Check the power cables regularly to ensure that they are undamaged. Also ensure
that nobody can trip over loose cables.
●If the product needs an external power supply, use the power supply that is deliv-
ered with the product or that is recommended in the product documentation or a
power supply that conforms to the country-specific regulations.
●Ensure that you can disconnect the product from the power source at any time.
Pull the power plug to disconnect the product. The power plug must be easily
accessible. If the product is integrated into a system that does not meet these
requirements, provide an easily accessible circuit breaker at the system level.
●Replace parts that are relevant to safety only by original parts, e.g. power cables or
fuses.
Performing measurements
Take the following measures for your safety:
●To ascertain voltage-free state, use an appropriate voltage tester. Any measure-
ment setup including an oscilloscope is not suitable for this purpose.
●The maximum input voltage on channel inputs and the external trigger input must
not exceed the value specified in the data sheet.
●Observe all voltage and current ratings of the instrument, the probes, and the
accessories. Exceeding the allowed voltages can lead to an electric shock.
Limits and ratings are marked on the products and listed in the data sheets.
Consider that the rated voltage depends on the frequency. The voltage limitation
curves or values are provided in the data sheet.
●Never cause any short circuits when measuring sources with high output currents.
●Use only probes and accessories that comply with the measurement category
(CAT) of your measurement task. If the product is rated for any measurement cate-
Safety instructions
Safety and regulatory information
R&S®RTP
14User Manual 1803.6484.02 ─ 03
gory, the permitted category is indicated on the product and in the data sheet. If
you use other than Rohde & Schwarz accessories, make sure that they are suita-
ble for the instrument and the measurement task.
●Set the correct attenuation factor on the instrument according to the probe being
used. Otherwise, the measurement results do not reflect the actual voltage level,
and you might misjudge the actual risk.
●When working with high voltages and current probes, observe the additional oper-
ating conditions specified in these safety instructions.
●The probe pins are extremely pointed and can easily penetrate clothes and the
skin. Handle the probe pins with great care. To exchange a probe pin, use tweez-
ers or pliers to avoid injuries. When transporting the accessories, always use the
box supplied with the probe.
●Prevent the probe from receiving mechanical shock. Avoid putting excessive strain
on the probe cable or exposing it to sharp bends. Touching a broken cable during
measurements can cause injuries.
●Set up all probe connections to the instrument before applying power.
Working with hazardous voltages
Voltages higher than 30 V RMS, or 42 V peak, or 60 V DC are regarded as hazardous
contact voltages. Direct contact with them can cause serious injuries.
Make sure that only electrically skilled persons use the products for measurements on
hazardous contact voltages. These working conditions require special education and
experience to perceive risks and to avoid hazards which electricity can create.
When working with hazardous contact voltages, use protective measures to preclude
direct contact with the measurement setup:
●Do not touch exposed connections and components when power is applied.
●Switch off the test circuit while connecting and disconnecting probe leads.
●Use only insulated voltage probes, test leads and adapters.
●Make sure that the input leads fulfill the safety requirements for your measurement.
The delivered input leads might have a jacket wear indicator that indicates a worn
jacket by different jacket color. In this case, do not use the input lead. Replace it
with a new one.
●When connecting to the DUT, keep your fingers behind finger guard. Remove jew-
elry, watches, and other metallic objects. Only use 4 mm safety banana plugs.
Working with current probes
When working with current probes, you can measure high-frequency currents or cur-
rents that contain high-frequency components.
●Switch off the test circuit while connecting the probe.
●Do not attach the clamp to bare unisolated conductors. To avoid injury from a short
circuit, measure at a location on an insulated wire where the insulation is sufficient
for the circuit voltage.
●Connect the probe only to the secondary side of a breaker. With this measure, you
avoid injury, if a short circuit occurs.
Safety instructions
Safety and regulatory information
R&S®RTP
15User Manual 1803.6484.02 ─ 03
●The following effects can cause burns and fire or damage to the measurement site:
– Eddy current loss can cause heating of the sensor head.
– Dielectric heating can cause heating of cord insulation and other materials.
●When measuring current that includes a high-frequency component, consider the
derating characteristics of the probe. Do not measure any current that exceeds the
rated current.
●Using the probes with high frequencies or strong magnetic fields may cause the
device to become abnormally hot, resulting in fire, equipment damage, or burns.
Measurement categories
IEC 61010-2-030 defines measurement categories that rate instruments on their ability
to resist short transient overvoltages that occur in addition to the working voltage. Use
the measurement setup only in electrical environments for which they are rated.
●0 - Instruments without rated measurement category
For measurements performed on circuits not directly connected to mains, for exam-
ple, electronics, circuits powered by batteries, and specially protected secondary
circuits. This measurement category is also known as CAT I.
●CAT II:
For measurements performed on circuits directly connected to the low-voltage
installation by a standard socket outlet, for example, household appliances and
portable tools.
●CAT III:
For measurements performed in the building installation, such as junction boxes,
circuit breakers, distribution boards, and equipment with permanent connection to
the fixed installation.
●CAT IV:
For measurements performed at the source of the low-voltage installation, such as
electricity meters and primary overcurrent protection devices.
Cleaning the product
Use a dry, lint-free cloth to clean the product. When cleaning, keep in mind that the
casing is not waterproof. Do not use liquid cleaning agents.
Safety instructions
Safety and regulatory information
R&S®RTP
16User Manual 1803.6484.02 ─ 03
Meaning of safety labels
Safety labels on the product warn against potential hazards.
Potential hazard
Read the product documentation to avoid personal injury or product damage.
Heavy product
Be careful when lifting, moving or carrying the product. Carrying the product requires a suffi-
cient number of persons or transport equipment.
Electrical hazard
Indicates live parts. Risk of electric shock, fire, personal injury or even death.
Protective conductor terminal
Connect this terminal to a grounded external conductor or to protective ground. This connec-
tion protects you against electric shock if an electric problem occurs.
1.2 Labels on the product
Labels on the casing inform about:
●Personal safety, see "Meaning of safety labels" on page 16
●Product and environment safety, see Table 1-1
●Identification of the product
Table 1-1: Labels regarding product and environment safety
Chassis grounding terminal
Take care when handling electrostatic sensitive devices.
Labeling in line with EN 50419 for disposal of electrical and electronic equipment after the prod-
uct has come to the end of its service life.
For more information, see "Disposing of electrical and electronic equipment" on page 2478.
1.3 Warning messages in the documentation
A warning message points out a risk or danger that you need to be aware of. The sig-
nal word indicates the severity of the safety hazard and how likely it will occur if you do
not follow the safety precautions.
WARNING
Potentially hazardous situation. Could result in death or serious injury if not avoided.
Warning messages in the documentation
Safety and regulatory information
R&S®RTP
17User Manual 1803.6484.02 ─ 03
CAUTION
Potentially hazardous situation. Could result in minor or moderate injury if not avoided.
NOTICE
Potential risks of damage. Could result in damage to the supported product or to other
property.
1.4 Where to find key documents on Rohde & Schwarz
Certificates issued to Rohde & Schwarz that are relevant for your country are provided
at www.rohde-schwarz.com/key-documents, e.g. concerning:
●Quality management
●Environmental management
●Information security management
●Accreditations
1.5 Korea certification class A
이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기
바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.
Korea certification class A
Preface
R&S®RTP
18User Manual 1803.6484.02 ─ 03
2 Preface
2.1 Key features
The R&S RTP high-performance oscilloscopes combine superior signal integrity with
fastest acquisition rate. It combines multiple instrument capabilities for time-correlated
debugging in one box. Outstanding key features are:
Real-time signal integrity
●Superior frontend performance
●Real-time de-embedding and advanced triggering
●Hardware accelerated processing for faster results
●Comprehensive analysis tools, for example, powerful protocol analysis, jitter analy-
sis functions, automatic compliance tests, spectrograms, and precise and wide-
band RF analysis
Multi-instrument capability
●Time-correlated analysis of different signal types
●Integrated arbitrary waveform and pattern generator that can be used, for example,
for protocol-based programming
●Easy-to-use serial protocol analysis for various protocols used in embedded
design, mobile communications and more
●General-purpose mixed signal option
●Multi-channel power consumption analysis with up to 8 additional voltage and 8
additional current measurement channels and very high dynamic range
●16 GHz pulse source
Compact and configurable
●Most compact high-end instrument platform
●Highest configuration flexibility
●Advanced user interface
For a detailed specification, refer to the data sheet.
2.2 Documentation overview
This section provides an overview of the R&S RTP user documentation.
2.2.1 Manuals and instrument help
You find the manuals on the product page at:
www.rohde-schwarz.com/manual/rtp
Documentation overview
Preface
R&S®RTP
19User Manual 1803.6484.02 ─ 03
Getting started manual
Introduces the R&S RTP and describes how to set up and start working with the instru-
ment, and describes basic operations. A printed English version is included in the
delivery. Editions in other languages are available on the product website.
Instrument help
The help offers quick, context-sensitive access to the complete information for the firm-
ware basic functionality and applications.
User manual (Instrument)
Describes all instrument functions in detail. It also provides an introduction to remote
control, a complete description of the remote control commands with programming
examples, and information on maintenance and instrument interfaces. Includes the
contents of the getting started manual.
The online version of the user manual provides the complete contents for immediate
display on the internet.
Manuals for compliance test options
For compliance test options, extra test procedure manuals are available. Test fixtures
are described in printed manuals, which are delivered with the fixture.
●The following test procedure manuals are available:
– USB 2.0/3.2 Compliance Test Procedures
– Ethernet Compliance Tests Procedures
– MIPI D-PHY Compliance Tests Procedures
– eMMC Compliance Tests Procedures
– PCIe Compliance Tests Procedures
– DDR3 Compliance Tests Procedures
– DDR4 Compliance Tests Procedures
– HDMI Tests Procedures
– ScopeSuite Automation
●The following test fixture manuals are available:
– R&S RT-ZF1 USB 2.0 Compliance Test Fixture Set
– R&S RT-ZF2 Ethernet Compliance Test Fixture Set
– R&S RT-ZF3 Frequency Converter Board (100BASE-T1)
– R&S RT-ZF4 10BASE-Te Test Fixture
– R&S RT-ZF5 Ethernet Probing Fixture
– R&S RT-ZF6 Frequency Converter Board (1000BASE-T1)
– R&S RT-ZF7 Automotive Ethernet T&D Fixture
– R&S RT-ZF7A and R&S RT-ZF7P SMA Adaptors
– R&S RT-ZF8 Automotive Ethernet Compliance Test Fixture
Documentation overview
Preface
R&S®RTP
20User Manual 1803.6484.02 ─ 03
Safety instructions
Provides safety information in many languages. The printed document is delivered with
the product.
Instrument security procedures manual
Deals with security issues when working with the R&S RTP in secure areas. It is avail-
able for download on the internet.
Service Manual
Describes the performance test for checking the rated specifications, module replace-
ment, firmware update, troubleshooting and fault elimination, and contains mechanical
drawings and spare part lists. The service manual is available for registered users on
the global Rohde & Schwarz information system (GLORIS, https://gloris.rohde-
schwarz.com).
2.2.2 Data sheet and brochure
The data sheet contains the technical specifications of the R&S RTP. It also lists the
firmware applications and their order numbers, and optional accessories. The brochure
provides an overview of the instrument and deals with the specific characteristics.
See www.rohde-schwarz.com/brochure-datasheet/rtp
2.2.3 Release notes, open source acknowledgment
The release notes list new features, improvements and known issues of the current
firmware version, and describe the firmware installation. The open source acknowledg-
ment document provides verbatim license texts of the used open source software. It
can also be read directly on the instrument.
See www.rohde-schwarz.com/firmware/rtp.
2.2.4 Application notes, application cards, videos
These documents deal with special applications or background information on particu-
lar topics.
●Application notes
●Media center
●Application videos
2.3 Options described in this document
In addition to the base unit, the following options are described in this documentation:
Options described in this document
/
