Page is loading ...
R&S®RTO2000
Oscilloscope
User Manual
1332972502
Version 22
(=PïI2)
This manual describes the following R&S®RTO models with firmware version 5.30:
●R&S®RTO2002 (1329.7002K02)
●R&S®RTO2004 (1329.7002K04)
●R&S®RTO2012 (1329.7002K12)
●R&S®RTO2014 (1329.7002K14)
●R&S®RTO2022 (1329.7002K22)
●R&S®RTO2024 (1329.7002K24)
●R&S®RTO2032 (1329.7002K32)
●R&S®RTO2034 (1329.7002K34)
●R&S®RTO2044 (1329.7002K44)
●R&S®RTO2064 (1329.7002K64)
© 2023 Rohde & Schwarz GmbH & Co. KG
Muehldorfstr. 15, 81671 Muenchen, Germany
Phone: +49 89 41 29 - 0
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
TEKTRONIX, TEK, and TEKPROBE are registered trademarks of Tektronix, Inc.
All other trademarks are the properties of their respective owners.
1332.9725.02 | Version 22 | R&S®RTO2000
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol, e.g. R&S®RTO is indicated as
R&S RTO.
Contents
R&S®RTO2000
3User Manual 1332.9725.02 ─ 22
Contents
1 Safety and regulatory information......................................................11
1.1 Safety instructions...................................................................................................... 11
1.2 Labels on the product.................................................................................................16
1.3 Warning messages in the documentation................................................................ 16
1.4 Where to find key documents on Rohde & Schwarz............................................... 17
1.5 Korea certification class A......................................................................................... 17
2 Preface.................................................................................................. 18
2.1 Key features.................................................................................................................18
2.2 Documentation overview............................................................................................19
2.3 Options described in this document.........................................................................21
2.4 Conventions used in the documentation..................................................................22
3 Getting started......................................................................................24
3.1 Preparing for use........................................................................................................ 24
3.2 Instrument tour............................................................................................................30
3.3 Operating the instrument........................................................................................... 45
4 Instrument setup..................................................................................72
4.1 System settings...........................................................................................................72
4.2 Option settings............................................................................................................76
4.3 Appearance settings...................................................................................................79
4.4 Display settings...........................................................................................................95
4.5 Frontpanel settings.....................................................................................................99
4.6 Preset setup...............................................................................................................103
4.7 Maintenance settings................................................................................................106
4.8 Save / recall................................................................................................................110
5 Acquisition and waveform setup......................................................114
5.1 Basics.........................................................................................................................114
5.2 Horizontal...................................................................................................................125
5.3 Horizontal accuracy.................................................................................................. 128
5.4 Acquire settings........................................................................................................ 131
5.5 Vertical setup.............................................................................................................144
Contents
R&S®RTO2000
4User Manual 1332.9725.02 ─ 22
5.6 Probes........................................................................................................................ 151
5.7 R&S RT-ZVC probe....................................................................................................177
5.8 Differential signals.................................................................................................... 186
5.9 Setting up the waveform.......................................................................................... 191
6 Triggers............................................................................................... 196
6.1 Basics of triggering.................................................................................................. 196
6.2 Setting up the trigger................................................................................................197
6.3 Trigger types..............................................................................................................199
6.4 Mode / Holdoff........................................................................................................... 226
6.5 Conditioning.............................................................................................................. 228
6.6 Actions on trigger..................................................................................................... 230
6.7 Qualification.............................................................................................................. 232
6.8 Sequence................................................................................................................... 235
6.9 Zone trigger............................................................................................................... 238
6.10 External trigger input................................................................................................242
7 Waveform analysis.............................................................................245
7.1 Zoom.......................................................................................................................... 245
7.2 Reference waveforms............................................................................................... 255
7.3 Mathematics.............................................................................................................. 263
7.4 History........................................................................................................................282
7.5 XY-diagram................................................................................................................ 288
8 Measurements....................................................................................292
8.1 Cursor measurements.............................................................................................. 292
8.2 Automatic measurements........................................................................................ 303
8.3 Quick measurements................................................................................................377
9 Spectrum analysis............................................................................. 379
9.1 FFT analysis.............................................................................................................. 379
9.2 Spectrum Analysis (option R&S RTO-K18).............................................................399
10 Mask testing....................................................................................... 403
10.1 About mask testing...................................................................................................403
10.2 Mask test settings..................................................................................................... 405
10.3 Mask testing on eye diagrams................................................................................. 417
Contents
R&S®RTO2000
5User Manual 1332.9725.02 ─ 22
10.4 Working with masks..................................................................................................420
11 Search functions................................................................................ 428
11.1 Overview: search definition and results................................................................. 428
11.2 Search setup..............................................................................................................429
11.3 Search gate................................................................................................................444
11.4 Search display presentation.................................................................................... 447
12 Data and file management.................................................................452
12.1 Save and recall user settings...................................................................................452
12.2 Save and recall waveform data and results............................................................461
12.3 Screenshots...............................................................................................................484
12.4 Reports.......................................................................................................................488
12.5 File selection dialog..................................................................................................490
13 Protocol analysis............................................................................... 492
13.1 Basics of protocol analysis......................................................................................492
13.2 I²C (option R&S RTO-K1).......................................................................................... 502
13.3 SPI bus (option R&S RTO-K1)..................................................................................517
13.4 UART/RS-232/RS-422/RS-485 (option R&S RTO-K2)............................................. 528
13.5 CAN and CAN FD (option R&S RTO-K3/K9)............................................................537
13.6 LIN (option R&S RTO-K3)......................................................................................... 563
13.7 FlexRay (option R&S RTO-K4)................................................................................. 577
13.8 Audio signals (option R&S RTO-K5)....................................................................... 593
13.9 MIL-1553 (option R&S RTO-K6)................................................................................612
13.10 ARINC 429 (option R&S RTO-K7).............................................................................629
13.11 Ethernet 10BASE-T and 100BASE-TX (option R&S RTO-K8)................................642
13.12 Ethernet 100BASE-T1 (option R&S RTO-57)...........................................................657
13.13 Ethernet 1000BASE-T1 (option R&S RTO-K58)...................................................... 676
13.14 SENT (option R&S RTO-K10)................................................................................... 694
13.15 RFFE (option R&S RTO-K40)....................................................................................726
13.16 D-PHY (option R&S RTO-K42)..................................................................................747
13.17 M-PHY and USB SSIC (option R&S RTO-K44 and K64).........................................763
13.18 Custom: Manchester / NRZ (option R&S RTO-K50)............................................... 793
13.19 8b/10b (option R&S RTO-K52)..................................................................................826
Contents
R&S®RTO2000
6User Manual 1332.9725.02 ─ 22
13.20 MDIO (option R&S RTO-K55)....................................................................................839
13.21 USB (option R&S RTO-K60)..................................................................................... 852
13.22 USB 3.1 (option R&S RTO-K61)............................................................................... 880
13.23 USBPD (option R&S RTO-K63)................................................................................ 902
13.24 SpaceWire (option R&S RTO-K65)...........................................................................915
13.25 PCIe (option R&S RTO-K72).....................................................................................927
13.26 CXPI (option R&S RTO-K76).....................................................................................957
13.27 DDR (option R&S RTO-K91 ).................................................................................... 976
14 Mixed signal option (MSO, R&S RTO-B1)........................................ 997
14.1 Digital channels and parallel buses........................................................................ 998
14.2 Display..................................................................................................................... 1007
14.3 Trigger...................................................................................................................... 1009
14.4 Measurements on digital channels....................................................................... 1022
14.5 Data export.............................................................................................................. 1023
14.6 Mathematics............................................................................................................ 1024
14.7 Search...................................................................................................................... 1024
15 Waveform generator (option R&S RTO-B6)................................... 1026
15.1 Setup of the waveform generator.......................................................................... 1026
15.2 Setup of the pattern generator...............................................................................1045
15.3 Output...................................................................................................................... 1049
15.4 Coupling settings....................................................................................................1052
15.5 Sync settings...........................................................................................................1053
15.6 Configuring the waveform generator.................................................................... 1054
16 Pulse source and TDR/TDT analysis (options R&S RTO-B7/K130)
........................................................................................................... 1058
16.1 Pulse source (option R&S RTO-B7).......................................................................1058
16.2 TDR/TDT analysis (option R&S RTO-K130).......................................................... 1061
17 I/Q software interface (option R&S RTO-K11)............................... 1074
17.1 I/Q mode...................................................................................................................1074
17.2 I/Q sampling setup.................................................................................................. 1074
17.3 I/Q data output.........................................................................................................1079
17.4 NFC trigger.............................................................................................................. 1081
Contents
R&S®RTO2000
7User Manual 1332.9725.02 ─ 22
18 Jitter analysis and clock data recovery......................................... 1083
18.1 Jitter measurements (options R&S RTO-K12/-K13).............................................1084
18.2 Advanced jitter and noise (option R&S RTO-K133/K134)....................................1094
18.3 Clock data recovery................................................................................................ 1127
19 Power analysis (option R&S RTO-K31).......................................... 1137
19.1 Power measurement selection...............................................................................1137
19.2 Overview of power measurement setup............................................................... 1149
19.3 Input..........................................................................................................................1152
19.4 Control loop............................................................................................................. 1166
19.5 Power path............................................................................................................... 1180
19.6 Output.......................................................................................................................1199
20 Deembedding (option R&S RTO-K121).......................................... 1215
20.1 Configuring the measurement setup for deembedding...................................... 1215
20.2 Deembedding settings............................................................................................1216
20.3 Responses............................................................................................................... 1225
20.4 Proven probe, proven cable...................................................................................1226
21 Compliance tests............................................................................. 1231
21.1 USB compliance test.............................................................................................. 1231
21.2 Ethernet compliance tests (options R&S RTO-K22/K23/K24/K25/K86/K87)...... 1232
21.3 D-PHY compliance tests (option R&S RTO-K26)..................................................1235
21.4 eMMC compliance tests (option R&S RTO-K92).................................................. 1235
21.5 PCIe compliance tests (option R&S RTO-K81).....................................................1236
21.6 DDR3 compliance tests (option R&S RTO-K91)................................................... 1236
22 Network operation and remote control.......................................... 1238
22.1 Operating system....................................................................................................1238
22.2 Setting up a network (LAN) connection................................................................1243
22.3 Web interface...........................................................................................................1248
22.4 Remote Desktop connection..................................................................................1253
22.5 Remote control........................................................................................................1255
23 Remote control commands.............................................................1270
23.1 Conventions used in Remote command description.......................................... 1276
23.2 Finding the appropriate command........................................................................ 1277
Contents
R&S®RTO2000
8User Manual 1332.9725.02 ─ 22
23.3 Programming examples......................................................................................... 1278
23.4 Frequently used parameters and suffixes............................................................ 1298
23.5 Common commands...............................................................................................1306
23.6 General remote settings......................................................................................... 1311
23.7 Instrument setup..................................................................................................... 1315
23.8 Acquisition and setup.............................................................................................1345
23.9 Trigger...................................................................................................................... 1410
23.10 Waveform analysis..................................................................................................1459
23.11 Cursor measurements............................................................................................ 1490
23.12 Automatic measurements...................................................................................... 1501
23.13 Spectrum analysis.................................................................................................. 1587
23.14 Mask testing............................................................................................................ 1604
23.15 Search...................................................................................................................... 1625
23.16 Data management................................................................................................... 1662
23.17 Protocols..................................................................................................................1691
23.18 Mixed signal option (MSO, R&S RTO-B1)............................................................. 2440
23.19 Waveform generator (option R&S RTO-B6).......................................................... 2464
23.20 Pulse source and TDR/TDT analysis (options R&S RTO-B7/K130).................... 2485
23.21 I/Q software interface (option R&S RTO-K11).......................................................2493
23.22 Jitter analysis and clock data recovery................................................................ 2500
23.23 Power analysis (option R&S RTO-K31).................................................................2540
23.24 Deembedding (option R&S RTO-K121)................................................................. 2580
23.25 Maintenance............................................................................................................ 2591
23.26 Status reporting...................................................................................................... 2593
23.27 Remote trace........................................................................................................... 2599
23.28 Deprecated commands...........................................................................................2602
24 Maintenance and support................................................................2608
24.1 Cleaning................................................................................................................... 2608
24.2 Contacting customer support................................................................................2608
24.3 Information for technical support..........................................................................2609
24.4 Data security............................................................................................................2609
24.5 Transporting............................................................................................................ 2609
24.6 Storage.....................................................................................................................2610
Contents
R&S®RTO2000
9User Manual 1332.9725.02 ─ 22
24.7 Disposal................................................................................................................... 2610
List of commands.............................................................................2611
Index..................................................................................................2693
Contents
R&S®RTO2000
10User Manual 1332.9725.02 ─ 22
Safety and regulatory information
R&S®RTO2000
11User Manual 1332.9725.02 ─ 22
1 Safety and regulatory information
The product documentation helps you to use the product safely and efficiently. Follow
the instructions provided here and in the Chapter 1.1, "Safety instructions",
on page 11.
Intended use
The R&S RTO oscilloscope is designed for measurements on circuits that are only indi-
rectly connected to the mains or not connected at all. It is not rated for any measure-
ment category.
The product is intended for the development, production and verification of electronic
components and devices in industrial, administrative, and laboratory environments.
Use the product only for its designated purpose. Observe the operating conditions and
performance limits stated in the data sheet.
Where do I find safety information?
Safety information is part of the product documentation. It warns you of potential dan-
gers and gives instructions on how to prevent personal injury or damage caused by
dangerous situations. Safety information is provided as follows:
●In Chapter 1.1, "Safety instructions", on page 11. The same information is provi-
ded in many languages as printed "Safety Instructions". The printed "Safety
Instructions" are delivered with the product.
●Throughout the documentation, safety instructions are provided when you need to
take care during setup or operation.
1.1 Safety instructions
Products from the Rohde & Schwarz group of companies are manufactured according
to the highest technical standards. To use the products safely, follow the instructions
provided here and in the product documentation. Keep the product documentation
nearby and offer it to other users.
Use the product only for its intended use and within its performance limits. Intended
use and limits are described in the product documentation such as the data sheet,
manuals and the printed "Safety Instructions for Oscilloscopes and Accessories" docu-
ment. If you are unsure about the appropriate use, contact Rohde & Schwarz customer
service.
Using the product requires specialists or specially trained personnel. These users also
need sound knowledge of at least one of the languages in which the user interfaces
and the product documentation are available.
Reconfigure or adjust the product only as described in the product documentation or
the data sheet. Any other modifications can affect safety and are not permitted.
Never open the casing of the product. Only service personnel authorized by
Rohde & Schwarz are allowed to repair the product. If any part of the product is dam-
Safety instructions
Safety and regulatory information
R&S®RTO2000
12User Manual 1332.9725.02 ─ 22
aged or broken, stop using the product. Contact Rohde & Schwarz customer service at
https://www.rohde-schwarz.com/support.
In these safety instructions, the term "product" covers instruments (oscilloscopes),
probes and their accessories.
Lifting and carrying the instrument
Check the data sheet for the maximum weight of the instrument. A single person can
only carry a maximum of 18 kg safely depending on age, gender and physical condi-
tion. If your instrument is heavier than 18 kg, do not move or carry it by yourself.
Use the instrument handles to move or carry the instrument. Do not use the mounted
accessories instead of the handles. Accessories are not designed to carry the weight
of the instrument.
To move the instrument safely, you can use lifting or transporting equipment such as lift
trucks and forklifts. Follow the instructions provided by the equipment manufacturer.
Choosing the operating site
Only use the product indoors. The product casing is not waterproof. Water that enters
can electrically connect the casing with live parts, which can lead to electric shock,
serious personal injury or death if you touch the casing. If Rohde & Schwarz provides
accessories designed for outdoor use of your product, e.g. a protective cover, you can
use the product outdoors.
Unless otherwise specified in the data sheet, you can operate the product up to an alti-
tude of 2000 m above sea level.
The product is suitable for pollution degree 2 environments where nonconductive con-
tamination can occur. For more information on environmental conditions such as ambi-
ent temperature and humidity, see the data sheet.
Setting up the product
Always place the product on a stable, flat and level surface with the bottom of the prod-
uct facing down. If the product is designed for different positions, secure the product so
that it cannot fall over.
If the product has foldable feet, always fold the feet completely in or out to ensure sta-
bility. The feet can collapse if they are not folded out completely or if the product is
moved without lifting it. The foldable feet are designed to carry the weight of the prod-
uct, but not an extra load.
If stacking is possible, keep in mind that a stack of products can fall over and cause
injury.
If you mount products in a rack, ensure that the rack has sufficient load capacity and
stability. Observe the specifications of the rack manufacturer. Always install the prod-
ucts from the bottom shelf to the top shelf so that the rack stands securely. Secure the
product so that it cannot fall off the rack.
Safety instructions
Safety and regulatory information
R&S®RTO2000
13User Manual 1332.9725.02 ─ 22
Connecting to power and grounding
The mains power supply input of the instrument complies with overvoltage category II.
It has to be connected to a fixed installation used to supply energy-consuming equip-
ment such as household appliances and similar loads. Be aware that electrically pow-
ered products have risks, such as electric shock, fire, personal injury or even death.
Take the following measures for your safety:
●Do not use an isolating transformer to connect the instrument to the mains power
supply.
●Before switching on the product, ensure that the voltage and frequency indicated
on the product match the available power source. If the power adapter does not
adjust automatically, set the correct value and check the rating of the fuse.
●Only use the power cable delivered with the product. It complies with country-spe-
cific safety requirements. Only insert the plug into an outlet with protective conduc-
tor terminal.
●If a product has an exchangeable fuse, its type and characteristics are indicated
next to the fuse holder. Before changing the fuse, switch off the instrument and dis-
connect it from the power source. How to change the fuse is described in the prod-
uct documentation.
●Only use intact cables and route them carefully so that they cannot be damaged.
Check the power cables regularly to ensure that they are undamaged. Also ensure
that nobody can trip over loose cables.
●If the product needs an external power supply, use the power supply that is deliv-
ered with the product or that is recommended in the product documentation or a
power supply that conforms to the country-specific regulations.
●Ensure that you can disconnect the product from the power source at any time.
Pull the power plug to disconnect the product. The power plug must be easily
accessible. If the product is integrated into a system that does not meet these
requirements, provide an easily accessible circuit breaker at the system level.
●Replace parts that are relevant to safety only by original parts, e.g. power cables or
fuses.
Performing measurements
Take the following measures for your safety:
●To ascertain voltage-free state, use an appropriate voltage tester. Any measure-
ment setup including an oscilloscope is not suitable for this purpose.
●The maximum input voltage on channel inputs and the external trigger input must
not exceed the value specified in the data sheet.
●Observe all voltage and current ratings of the instrument, the probes, and the
accessories. Exceeding the allowed voltages can lead to an electric shock.
Limits and ratings are marked on the products and listed in the data sheets.
Consider that the rated voltage depends on the frequency. The voltage limitation
curves or values are provided in the data sheet.
●Never cause any short circuits when measuring sources with high output currents.
●Use only probes and accessories that comply with the measurement category
(CAT) of your measurement task. If the product is rated for any measurement cate-
Safety instructions
Safety and regulatory information
R&S®RTO2000
14User Manual 1332.9725.02 ─ 22
gory, the permitted category is indicated on the product and in the data sheet. If
you use other than Rohde & Schwarz accessories, make sure that they are suita-
ble for the instrument and the measurement task.
●Set the correct attenuation factor on the instrument according to the probe being
used. Otherwise, the measurement results do not reflect the actual voltage level,
and you might misjudge the actual risk.
●When working with high voltages and current probes, observe the additional oper-
ating conditions specified in these safety instructions.
●The probe pins are extremely pointed and can easily penetrate clothes and the
skin. Handle the probe pins with great care. To exchange a probe pin, use tweez-
ers or pliers to avoid injuries. When transporting the accessories, always use the
box supplied with the probe.
●Prevent the probe from receiving mechanical shock. Avoid putting excessive strain
on the probe cable or exposing it to sharp bends. Touching a broken cable during
measurements can cause injuries.
●Set up all probe connections to the instrument before applying power.
Working with hazardous voltages
Voltages higher than 30 V RMS, or 42 V peak, or 60 V DC are regarded as hazardous
contact voltages. Direct contact with them can cause serious injuries.
Make sure that only electrically skilled persons use the products for measurements on
hazardous contact voltages. These working conditions require special education and
experience to perceive risks and to avoid hazards which electricity can create.
When working with hazardous contact voltages, use protective measures to preclude
direct contact with the measurement setup:
●Do not touch exposed connections and components when power is applied.
●Switch off the test circuit while connecting and disconnecting probe leads.
●Use only insulated voltage probes, test leads and adapters.
●Make sure that the input leads fulfill the safety requirements for your measurement.
The delivered input leads might have a jacket wear indicator that indicates a worn
jacket by different jacket color. In this case, do not use the input lead. Replace it
with a new one.
●When connecting to the DUT, keep your fingers behind finger guard. Remove jew-
elry, watches, and other metallic objects. Only use 4 mm safety banana plugs.
Working with current probes
When working with current probes, you can measure high-frequency currents or cur-
rents that contain high-frequency components.
●Switch off the test circuit while connecting the probe.
●Do not attach the clamp to bare unisolated conductors. To avoid injury from a short
circuit, measure at a location on an insulated wire where the insulation is sufficient
for the circuit voltage.
●Connect the probe only to the secondary side of a breaker. With this measure, you
avoid injury, if a short circuit occurs.
Safety instructions
Safety and regulatory information
R&S®RTO2000
15User Manual 1332.9725.02 ─ 22
●The following effects can cause burns and fire or damage to the measurement site:
– Eddy current loss can cause heating of the sensor head.
– Dielectric heating can cause heating of cord insulation and other materials.
●When measuring current that includes a high-frequency component, consider the
derating characteristics of the probe. Do not measure any current that exceeds the
rated current.
●Using the probes with high frequencies or strong magnetic fields may cause the
device to become abnormally hot, resulting in fire, equipment damage, or burns.
Measurement categories
IEC 61010-2-030 defines measurement categories that rate instruments on their ability
to resist short transient overvoltages that occur in addition to the working voltage. Use
the measurement setup only in electrical environments for which they are rated.
●0 - Instruments without rated measurement category
For measurements performed on circuits not directly connected to mains, for exam-
ple, electronics, circuits powered by batteries, and specially protected secondary
circuits. This measurement category is also known as CAT I.
●CAT II:
For measurements performed on circuits directly connected to the low-voltage
installation by a standard socket outlet, for example, household appliances and
portable tools.
●CAT III:
For measurements performed in the building installation, such as junction boxes,
circuit breakers, distribution boards, and equipment with permanent connection to
the fixed installation.
●CAT IV:
For measurements performed at the source of the low-voltage installation, such as
electricity meters and primary overcurrent protection devices.
Cleaning the product
Use a dry, lint-free cloth to clean the product. When cleaning, keep in mind that the
casing is not waterproof. Do not use liquid cleaning agents.
Safety instructions
Safety and regulatory information
R&S®RTO2000
16User Manual 1332.9725.02 ─ 22
Meaning of safety labels
Safety labels on the product warn against potential hazards.
Potential hazard
Read the product documentation to avoid personal injury or product damage.
Electrical hazard
Indicates live parts. Risk of electric shock, fire, personal injury or even death.
Protective conductor terminal
Connect this terminal to a grounded external conductor or to protective ground. This connec-
tion protects you against electric shock if an electric problem occurs.
1.2 Labels on the product
Labels on the casing inform about:
●Personal safety, see "Meaning of safety labels" on page 16
●Product and environment safety, see Table 1-1
●Identification of the product
Table 1-1: Labels regarding product and environment safety
Chassis grounding terminal
Take care when handling electrostatic sensitive devices.
Labeling in line with EN 50419 for disposal of electrical and electronic equipment after the prod-
uct has come to the end of its service life.
For more information, see "Disposing of electrical and electronic equipment" on page 2610.
1.3 Warning messages in the documentation
A warning message points out a risk or danger that you need to be aware of. The sig-
nal word indicates the severity of the safety hazard and how likely it will occur if you do
not follow the safety precautions.
WARNING
Potentially hazardous situation. Could result in death or serious injury if not avoided.
CAUTION
Potentially hazardous situation. Could result in minor or moderate injury if not avoided.
Warning messages in the documentation
Safety and regulatory information
R&S®RTO2000
17User Manual 1332.9725.02 ─ 22
NOTICE
Potential risks of damage. Could result in damage to the supported product or to other
property.
1.4 Where to find key documents on Rohde & Schwarz
Certificates issued to Rohde & Schwarz that are relevant for your country are provided
at www.rohde-schwarz.com/key-documents, e.g. concerning:
●Quality management
●Environmental management
●Information security management
●Accreditations
1.5 Korea certification class A
이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기
바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.
Korea certification class A
Preface
R&S®RTO2000
18User Manual 1332.9725.02 ─ 22
2 Preface
2.1 Key features
The R&S RTO oscilloscope brings various benefits in your daily work. Outstanding key
features are:
Best oscilloscope performance:
●Up to 16-bit vertical resolution
●Trigger on any detail you can see
●Quickly find signal faults with 1 Million waveforms/s
●Integrated spectrum analysis
Widest range of capabilities:
●Fast acquisition rate even with industry leading 2 Gsample deep memory
●First zone trigger in time and frequency domain
●Analyze previous acquisitions - always available in history buffer
●Deep toolset for signal analysis
Powerful user interface:
●High-resolution 12.1’’ capacitive touchscreen with gesture support
●Easily customizable waveform display with SmartGrid
●Fast access to important tools
●Documentation at the press of a button
Engineered for multi-domain challenges:
●Class leading MSO
●Trigger and decode for serial protocols
●Advanced spectrum analysis
●Integrated arbitrary waveform and pattern generator
●Power measurements
●Signal integrity testing with advanced eye and jitter analysis
●Automatic compliance tests
●EMI debugging with oscilloscopes
●IQ and RF analysis
●Extensive probe portfolio for voltage, current and more
For a detailed specification refer to the data sheet.
Key features
Preface
R&S®RTO2000
19User Manual 1332.9725.02 ─ 22
2.2 Documentation overview
This section provides an overview of the R&S RTO user documentation.
2.2.1 Manuals and instrument help
You find the manuals on the product page at:
www.rohde-schwarz.com/manual/rto
Getting started manual
Introduces the R&S RTO and describes how to set up and start working with the instru-
ment, and describes basic operations. A printed English version is included in the
delivery. Editions in other languages are available on the product website.
Instrument help
The help offers quick, context-sensitive access to the complete information for the firm-
ware basic functionality and applications.
User manual (Instrument)
Describes all instrument functions in detail. It also provides an introduction to remote
control, a complete description of the remote control commands with programming
examples, and information on maintenance and instrument interfaces. Includes the
contents of the getting started manual.
The online version of the user manual provides the complete contents for immediate
display on the internet.
Manuals for compliance test options
For compliance test options, extra test procedure manuals are available. Test fixtures
are described in printed manuals, which are delivered with the fixture.
●The following test procedure manuals are available:
– USB 2.0 Compliance Test Procedures
– Ethernet Compliance Tests Procedures
– MIPI D-PHY Compliance Tests Procedures
– eMMC Compliance Tests Procedures
– PCIe Compliance Tests Procedures
– DDR3 Compliance Tests Procedures
– ScopeSuite Automation
●The following test fixture manuals are available:
– R&S RT-ZF1 USB 2.0 Compliance Test Fixture Set
– R&S RT-ZF2 Ethernet Compliance Test Fixture Set
– R&S RT-ZF3 Frequency Converter Board (100BASE-T1)
– R&S RT-ZF4 10BASE-Te Test Fixture
Documentation overview
Preface
R&S®RTO2000
20User Manual 1332.9725.02 ─ 22
– R&S RT-ZF5 Ethernet Probing Fixture
– R&S RT-ZF6 Frequency Converter Board (1000BASE-T1)
– R&S RT-ZF7 Automotive Ethernet T&D Fixture
– R&S RT-ZF7A and R&S RT-ZF7P SMA Adaptors
– R&S RT-ZF8 Automotive Ethernet Compliance Test Fixture
Safety instructions
Provides safety information in many languages. The printed document is delivered with
the product.
Instrument security procedures manual
Deals with security issues when working with the R&S RTO in secure areas. It is avail-
able for download on the internet.
Service Manual
Describes the performance test for checking the rated specifications, module replace-
ment, firmware update, troubleshooting and fault elimination, and contains mechanical
drawings and spare part lists. The service manual is available for registered users on
the global Rohde & Schwarz information system (GLORIS, https://gloris.rohde-
schwarz.com).
2.2.2 Data sheet and brochure
The data sheet contains the technical specifications of the R&S RTO. It also lists the
firmware applications and their order numbers, and optional accessories. The brochure
provides an overview of the instrument and deals with the specific characteristics.
See www.rohde-schwarz.com/brochure-datasheet/rto
2.2.3 Release notes, open source acknowledgment
The release notes list new features, improvements and known issues of the current
firmware version, and describe the firmware installation. The open source acknowledg-
ment document provides verbatim license texts of the used open source software. It
can also be read directly on the instrument.
See www.rohde-schwarz.com/firmware/rto.
2.2.4 Application notes, application cards, videos
These documents deal with special applications or background information on particu-
lar topics.
●Application notes
●Media Center
Documentation overview
/
